Professional Documents
Culture Documents
SPECIFICATIONS
LIFTING EQUIPMENT
TOWING
LUBRICANTS - CONSUMABLES
DRAINING - REFILLING
"The repair methods given by the manufacturer in this document are based on the All copyrights reserved by Renault.
technical specifications current when it was prepared.
Copying or translating, in part or in full, of this document or use of the service part
The methods may be modified as a result of changes by the manufacturer in the reference numbering system is forbidden without the prior written authority of
production of the various component units and accessories from which his vehicles Renault.
are constructed".
PRC0001
General
Contents
Pages Pages
04 LUBRICANTS - CONSUMABLES
Packaging 04-1
SPECIFICATIONS
Engine - Clutch - Gearbox 01
Engine
B531 - C531 - L531 C1J 1397 180 CP 3300 JB0 - JB1 - JB4 - JB5
B53W - C53W - L53W E7F 1171 180 CP 3300 JB0 - JB1 - JB3
01-1
SPECIFICATIONS
Vehicle identification 01
IDENTIFICATION OF F3P ENGINES WITH REDUCED CUBIC CAPACITY
APPROVAL VEHICLE
ENGINE NUMBER
LETTER TYPE
E 704
H 706
X53 Y
E 708
H 760
H 706
053 A
F3P
H 760
053 B - F - H
J 765
X53 V
053 C - D - H
A 682
X53 8
X53 Y = B53 Y, C53 Y, L53 Y Vehicle type code starting with a letter.
A B C D
A : the engine type
B : the vehicle type approval letter
000 0 000 / C : the identity of RENAULT SA
D : the engine number
0000000 E : the engine manufacturing number
F : letter indicating the factory at which the en-
gine was manufactured (e.g.: C for Cléon)
F E
90775
01-2
SPECIFICATIONS
Vehicle identification 01
LOCATION OF THE VEHICLE IDENTIFICATION PLATE
Position n° 1 Position n° 3
95890-1R
92025R
Position n° 2
94946R
01-3
SPECIFICATIONS
Vehicle identification 01
METAL PLATE (Position n° 1)
2 3 1 4
REGIE NATIONALE A
DES USINES RENAULT B2
01-4
SPECIFICATIONS
VEHICLE IDENTIFICATION 01
METAL PLATE (Position n° 2)
REGIE NATIONALE 1
A
DES USINES RENAULT 0000 3
00 000 000 4
B AU 0000-00-00
00 000 000 7
C VF1000000
0000000 6
D 00000000
8
E 0000 kg
5
F 0000 kg 2
G 1 - 0000 kg
H 2 - 0000 kg
WARNING: The 7 characters of the manufacturing number must not be separated. For vehicles manufactured
before that date, the manufacturing number is 7 numbers.
NOTE: some of these items of information are not required for certain export markets. The plates described
above are shown in their most complete form.
01-5
SPECIFICATIONS
Vehicle identification 01
METAL PLATE (Position n° 3)
1 VF0000000
2 00000000 9
8 0000
7 00 000 000 10
14 00 000 000 11
13 0000000
12
01-6
SPECIFICATIONS
Vehicle identification 01
This consists of:
At A : the manufacturer’s name,
At B : the EU official approval number
At 1 : the official type number preceded by the manufacturer’s worldwide identification code
(for example : VF1 for RENAULT France),
At 2 : the chassis number,
At 3 : the gross vehicle weight,
At 4 : the gross train weight,
At 5 : the maximum permissible front axle weight,
At 6 : the maximum permissible rear axle weight,
At 7 : the first number indicates the gearbox or the factory options
the second number indicates the level of equipment,
At 8 : the vehicle type
At 9 : the technical equipment number,
At 10 : the factory option additional equipment,
At 11 : the level of equipment,
At 12 : the paint identification code,
At 13 : a letter indicating the factory of manufacture, followed by the manufacturing number,
At 14 : the trim identification code.
NOTE: some of these items of information are not required for certain export markets. The plates described
above are shown in their most complete form.
The equipment code, three letters at (9), must be documented when vehicle identification is required (orde-
ring of replacement parts, warranty form, etc).
01-7
SPECIFICATIONS
Vehicle identification 01
Due to the European depollution standards, the "ABCD" coding of some vehicles has become saturated follo-
wing the introduction of new engines (letter "D"), the body code "A" therefore becomes "A’".
A A’ "ABCD" "A’BCD"
REMINDER:
01-8
LIFTING EQUIPMENT
Trolley jack - Axle stands 02
Safety symbol (special precautions to be taken when carrying out work).
It is forbidden to lift the vehicle by taking the load under the front suspension arms. Use whichever of the
sockets Cha. 408-02 that suits the trolley jack to fit pad Cha. 280-02.
LIFTING WITH THE TROLLEY JACK FROM THE LIFTING WITH THE TROLLEY JACK FROM THE
FRONT REAR
Apply the handbrake or place chocks under the It is FORBIDDEN to lift the rear of the vehicle
rear wheels. taking the load under the rear axle. Lift each
wheel separately taking the load under the
Use pad Cha. 280-02. vehicle jacking points.
92556R
91936G2 85679-1G13
02-1
LIFTING EQUIPMENT
Trolley jack - Axle stands 02
LIFTING WITH THE TROLLEY JACK FROM THE SIDE AXLE STANDS
Use pad Cha. 280-02. When taking the weight of the vehicle on the axle
stands ensure that the stands are under the
Take the load on the body sill, under the front vehicle jacking points (1).
door.
Stands are to be placed under the rear end by
Ensure that the body sill flange locates correctly in lifting the vehicle from the side.
the groove in the pad.
87709R
91936G3 85679-1G14
02-2
TOWING
All models 03
FOR TOWING, REFER TO THE LEGISLATION IN FORCE IN THE COUNTRY CONCERNED.
The towing points are only to be used for towing the vehicle on the road. In no circumstances are they to be
used for pulling the vehicle out of a ditch, or for any other similar operation nor are they to be used for lifting
the vehicle either directly or indirectly.
FRONT REAR
92020S 92019S
03-1
LUBRICANTS - CONSUMABLES
Packaging 04
DESCRIPTION PACK SIZE PART NUMBER
GREASES
• ANTI-SEIZE
(high temperature grease) Turbo etc. 80 ml tube 77 01 422 307
• MULTIPURPOSE GREASE
wheel sensor Aerosol 77 01 422 308
04-1
LUBRICANTS - CONSUMABLES
Packaging 04
DESCRIPTION PACK SIZE PART NUMBER
ADHESIVES
CLEANERS - LUBRICANTS
04-2
LUBRICANTS - CONSUMABLES
Packaging 04
DESCRIPTION PACK SIZE PART NUMBER
VARNISH
AIR CONDITIONING
Fixed cubic capacity compressor oil SANDEN SP 250 ml (R134a) 77 11 143 700
20
Variable cubic capacity compressor oil SP10 250 ml (R134a) 77 01 419 313
04-3
DRAINING - REFILLING
Engine 05
ESSENTIAL SPECIAL TOOLS
98486R 92179R
98701R 92178R
05-1
DRAINING - REFILLING
Engine 05
REFILLING: plug (2)
dipstick (3)
92035R 92715R
95748R 95747R
05-2
DRAINING - REFILLING
Gearbox 05
MANUAL
ENGINES C - E - F
98486R1
92081R DI0522
05-3
DRAINING - REFILLING
Power assisted steering 05
CHECKING THE LEVEL
92030R
05-4
VALUES AND SETTINGS
Dimensions 07
Phase 1
91936R1
07-1
VALUES AND SETTINGS
Dimensions 07
Phase 2
95890R
F 1.426
07-2
VALUES AND SETTINGS
Dimensions 07
Models D and L
95888R4
A 0.813 F 1.426
07-3
VALUES AND SETTINGS
Capacities - Grades 07
Capacity
Units Grade
in litres
PETROL
- 15 °C + 25 °C
- 30 °C - 20 °C - 10 °C 0°C + 10 °C + 20 °C + 30 °C
CCMC-G4 15W40-15W50
ACEA A2-96/A3-96 15W40-15W50
CCMC-G5 10W30-10W40-10W50
ACEA A2-96/A3-96 10W30-10W40-10W50
CCMC-G5 5W30
ACEA A2-96/A3-96 5W30
C 3
CCMC-G5 5W40-5W50
E 3.5 ACEA A2-96/A3-96 5W40-5W50
- 15 °C
- 30 °C - 20 °C - 10 °C 0°C + 10 °C + 20 °C + 30 °C
API SH 15W40
API SH 10W40
API SH 10W30
07-4
VALUES AND SETTING
Capacities - Grades 07
Capacity
Units Grade
in litres
- 15 °C + 25 °C
- 30 °C - 20 °C - 10 °C 0 °C + 10 °C + 20 °C + 30 °C
CCMC-PD2 15W40
ACEA B2-96/B3-96 15W40
CCMC-PD2 10W40
ACEA B2-96/B3-96 10W40
CCMC-PD2 5W30
ACEA B2-96/B3-96 5W30
CCMC-PD2 5W40
ACEA B2-96/B3-96 5W40
F8Q 5
Other countries
DIESEL
- 15 °C + 15
- 30 °C - 20 °C - 10 °C 0 °C + 10 °C + 20 °C + 30 °C
API CF 15W40
API CF 10W40
07-5
VALUES AND SETTINGS
Capacities - Grades 07
Capacity
Units Grade Special points
in litres
Manual
gearbox All countries: TRANSELF TRX 75 W 80 W
(Standards API GL5 or MIL-L 2105 C or D)
JB0 3.25
JB1 3.40
JB3 3.40
JB4 2.80
JB5 2.90
JC5 3.10
Automatic
transmission
Normal : 0.7 SAE J 1703 The brake fluid must be of a type approved by our
Braking system
ABS : 1 and DOT 4 Design office.
Fuel Unleaded
55 -
tank petrol/diesel
Engine cooling
system
C1G - C1J - C2J 5.4
C3J 6
E6J 5.2
E7F - E7J 5,2 - -
F2N - F3N 6
F3P 6.1 or 6.5
F7P 7
F8Q 6.8
07-6
VALUES AND SETTINGS
Belt tension 07
ESSENTIAL SPECIAL TOOLS
96601R
Principle Procedure
Via the pressure piece button (1), the pressure Setting zero:
piece (2) and the external pads (3), the sensor ap- - switch on the equipment (button E) with the
plies a constant slack to the belt. pressure piece button (1) head down,
- if 0 is displayed, do not adjust anything,
The reactive force of the belt is measured using a - if there is no display, check the charge of the
test unit (4) fitted with stress gauges. equipment’s 9 volt battery,
- if a value other than 0 is displayed, operate
The pulling of the gauges creates a variation in screw (F) until 0 is obtained .
their electrical resistances. Once converted by the
equipment, this variation is displayed in SEEM
units (US).
07-7
VALUES AND SETTINGS
Belt tension 07
Checking the calibration
Position the standard spring blade (Z) on the sensor as shown on the diagram (checking value etched towards
the top , (A) minimum value, (B) maximum value).
Tighten the pressure piece button (1) until it clicks (three "CLICKS").
Check that the display shows a value X between values (A and B) (A ≤ X ≤ B).
COMMENT: It may be necessary to carry out a few preliminary test in order to obtain the correct value.
If the values are incorrect after several tests, contact your local After Sales Head Office.
NOTE: Each apparatus has its own standard spring blade which is not interchangeable.
96602R
07-8
VALUES AND SETTINGS
Accessories belt tension 07
RECOMMENDATIONS FOR FITTING BELTS:
V-BELT
Tension the belt until the recommended fitting value is displayed on Mot. 1273.
Check that the tension is within the fitting tension tolerance, adjust it if it is not.
Tension the belt until 80% of the recommended fitting value is displayed on Mot. 1273.
Check that the tension is within the tolerance of 80% of the fitting tension. If it is not, adjust it to 80% of the
fitting value.
NOTE: The V-belt is changed depending on its condition or the noise which it makes.
For the measuring point, fit the sensor of Mot. 1273 in place of Elé. 346-04.
07-9
VALUES AND SETTINGS
Accessories belt tension 07
Toothed BELT
Tensioning procedure
Tension the belt until the recommended fitting value is displayed on Mot. 1273.
Check that the tension is within the fitting tension tolerance, adjust it if it is not.
NOTE :
Change the belt if the tension is below the minimum operating tension.
Small cuts or cracks are not criteria for changing the belt.
For the measuring point, fit the sensor of Mot. 1273 in place of Elé. 346-04.
07-10
VALUES AND SETTINGS
C
ENGINE
Accessories belt tension 07
ALTERNATOR AND COOLANT PUMP
92648R1
A Coolant pump
B Crankshaft pump
C Alternator pump
→ Tension checking point
90 ± 6
Fitting 105 ± 6 (*)
89 ± 5 (*)
Minimum
64
operating 75 (*)
68 (*)
tension
07-11
VALUES AND SETTINGS
E
ENGINE
Accessories belt tension 07
ALTERNATOR
92320R2
B Crankshaft pulley
C Alternator pulley
→ Tension checking point
E6J engine
Air conditioning
Toothed alternator
Tension Air conditioning and power assisted
belt Alternator V-belt
(US=SEEM unit) V-belt steering belt
(three teeth)
(four teeth)
Fitting 84 ± 6 83 ± 7 90 106
Minimum operating
52 70 72 59
tension
E7J engine
Air
conditioning
Toothed Toothed power Air
Tension Alternator and power
alternator belt assisted steering conditioning
(US=SEEM unit) V-belt assisted
(three teeth) belt (three teeth) V-belt
steering belt
(four teeth)
Fitting 84 ± 6 84 ± 5 83 ± 7 90 106
Minimum operating
52 46 70 72 59
tension
07-12
VALUES AND SETTINGS
F
ENGINE
Accessories belt tension 07
F2N, F3N engines
Toothed belt
Toothed belt Toothed belt
(six teeth)
Tension (six teeth) (six dents teeth)
Alternator
(US=SEEM unit) Alternator Alternator and
Air conditioning and
Power assisted steering coolant pump
power assisted steering
Fitting 106 ± 6 98 ± 6 83 ± 6
Minimum operating
71 73 57
tension
F7P engine
Fitting 91 ± 5 95 ± 5
Minimum
operating 58 57
tension
F8Q engine
Toothed belt
Toothed belt
(six teeth) Toothed belt
(six teeth) Toothed belt
Tension Alternator (six dents teeth)
Alternator (six teeth)
(US=SEEM unit) Air conditioning Alternator
Power assisted Alternator
and power assisted Air conditioning
steering
steering
112 ± 4
Fitting 101 ± 5 99 ± 5 97 ± 3
116 ± 7*
Minimum operating
67 67 68 67
tension
07-13
VALUES AND SETTINGS
F
ENGINE
Accessories belt tension 07
ALTERNATOR AND COOLANT PUMP
87413R1
A Coolant pump
B Crankshaft
C Alternator
E Air conditioning compressor
86979R1
91136R3 92290R2
07-14
VALUES AND SETTINGS
Timing belt tension 07
Tensioning procedure E engine
07-15
VALUES AND SETTINGS
Timing belt tension 07
F engine (petrol) except F7P F8Q engine
96528R1 99175R
Belt tension (in SEEM units) Belt tension (in SEEM units)
07-16
VALUES AND SETTINGS
Cylinder head tightening 07
E ENGINE C ENGINE
Grease the bolt threads and underneath the bolt Grease the bolt threads and underneath the bolt
heads with engine oil. heads with engine oil.
REMINDER: In order to tighten the bolts correctly, REMINDER: In order to tighten the bolts correctly,
remove any oil from the cylinder head securing remove any oil from the cylinder head securing
holes using a syringe. holes using a syringe.
Tighten the cylinder head in the order shown be- Tighten the cylinder head in the order shown be-
low: low:
8 4 1 5 9
7 3 2 6 10
90775S 81528-1S
07-17
VALUES AND SETTINGS
Cylinder head tightening 07
For engines F2N - F3N - F3P, refer to the "F ENGINE" section.
CYLINDER HEAD GASKET WITH ASBESTOS CYLINDER HEAD GASKET WITH NO ASBESTOS
Grease the bolt threads and underneath the bolt All of the bolts must be changed automatically af-
heads with engine oil. ter removal.
REMINDER: In order to tighten the bolts correctly, Grease the bolt threads and underneath the bolt
remove any oil from the cylinder head securing heads with engine oil.
holes using a syringe.
REMINDER: In order to tighten the bolts correctly,
Tighten the cylinder head in the order shown be- remove any oil from the cylinder head securing
low: holes using a syringe.
8 4 1 5 9
8 4 1 5 9
7 3 2 6 10
7 3 2 6 10
90775S
07-18
VALUES AND SETTINGS
Cylinder head tightening 07
F7P ENGINE
8 4 1 5 9
7 3 2 6 10
90775S
07-19
VALUES AND SETTINGS
Cylinder head tightening 07
F ENGINE (diesel)
CYLINDER HEAD GASKET WITH ASBESTOS CYLINDER HEAD GASKET WITHOUT ASBESTOS
This operation is carried out when cold, when the All of the bolts must be changed automatically af-
cylinder head is refitted, and there is no other rea- ter removal.
son for it to be carried out.
Grease the bolt threads and underneath the bolt
Grease the bolt threads and underneath the bolt heads with engine oil.
heads with engine oil.
REMINDER: In order to tighten the bolts correctly,
REMINDER: In order to tighten the bolts correctly, remove any oil from the cylinder head securing
remove any oil from the cylinder head securing holes using a syringe.
holes using a syringe.
Tighten the cylinder head in the order shown be-
Tighten the cylinder head in the order shown be- low:
low:
81528-1S
81528-1S
1st tightening to 3 daN.m.
1st tightening to 3 daN.m.
2nd tightening (angle) : 50° ± 4 °.
2nd tightening (angle) : 7 daN.m.
Wait for at least three minutes.
Wait for at least three minutes.
Slacken bolt by bolt until they are completely free,
Slacken bolt by bolt until they are completely free, then tighten to 2.5 daN,m.
then tighten to 2 daN,m.
2nd tightening (angle) : 213° ± 7°.
2nd tightening (angle) : 123° ± 2°.
The cylinder head is not retightened except on
the F8Q Turbo.
- Special features of engines F8Q 610, 740, 744,
768.
- Following an increase in engine temperature
(operation of the fan).
- Wait until the engine returns to ambient tem-
perature.
- In the recommended order, again tighten bolts
1-2, 3-4, 5-6, 7-8, 9-10, angle 120° ± 7°.
07-20
VALUES AND SETTINGS
Main brake components and dimensions 07
B/C/L/S B/C/D/L/S B/C/L/S B/C/D/L
530, 531 533, 536 538, 53F 539, 53D
532, 534 538, 53C 53K, 53T X53 ABS*
535, 537 53F, 53K
53A, 53B 53T, 53V 3/4/5
53G, 53H 53Y, 53Z 53C, 53D
53J, 53W 53H
3/4/5/8
53A, 53F
53H
(1) The brake discs cannot be ground. The discs must be changed if they are excessively scratched or worn.
(2) Wheel cylinder with integral fixed compensator: in the event of a wheel cylinder or compensator
function fault: change the assembly, repair is forbidden.
07-21
VALUES AND SETTINGS
Front axle setting values 07
MANUAL STEERING
ALL TYPES EXCEPT B539 - C539 - L539 - B53D - C53D - D53D - L53D
2°55’ H5-H2= 21 mm
2°25 H5-H2= 40 mm
1°55’ H5-H2= 59 mm NOT ADJUSTABLE
1°25’ H5-H2= 78 mm
0°55’ H5-H2= 97 mm
Maximum left/ right
difference= 1°
78423S3
CAMBER
1°35’ H1-H2= 22 mm
0°30’ H1-H2= 59 mm
- 0°5’ ± 30’ H1-H2= 86 mm NOT ADJUSTABLE
- 0°30’ H1-H2= 115 mm
- 0°45’ H1-H2= 149 mm
Maximum left/right
difference = 1°
78423S1
KING PIN INCLINATION
10°45’ H1-H2= 22 mm
12°5’ H1-H2= 59 mm
12°55’ ± 30’ H1-H2= 86 mm NOT ADJUSTABLE
13°40’ H1-H2= 115 mm
14°15’ H1-H2= 149 mm
Maximum left/right
difference = 1°
78423S2
PARALLELISM
(Toe-out) Adjusted by
rotating track rod
sleeves
For two wheels UNLADEN 1 turn= 30’
0°10’ ± 10’ (3 mm)
(1 ± 1 mm)
78423S
POSITION FOR TIGHTENING RUBBER BUSHES
UNLADEN
- -
81603S1
07-22
VALUES AND SETTINGS
Front axle setting values 07
POWER ASSISTED STEERING
ALL TYPES EXCEPT B539 - C539 - L539 - B53D - C53D - D53D - L53D
5° H5-H2= 21 mm
4°30’ H5-H2= 40 mm
4° H5-H2= 59 mm NOT ADJUSTABLE
3°30’ H5-H2= 78 mm
3° H5-H2= 97 mm
Maximum left/right
difference= 1°
78423S3
CAMBER
1°35’ H1-H2= 22 mm
0°30’ H1-H2= 59 mm
- 0°5’ ± 30’ H1-H2= 86 mm NOT ADJUSTABLE
- 0°30’ H1-H2= 115 mm
- 0°45’ H1-H2= 149 mm
Maximum left/right
difference= 1°
78423S1
KING PIN INCLINATION
10°45’ H1-H2= 22 mm
12°5’ H1-H2= 59 mm
12°55’ ± 30’ H1-H2= 86 mm NOT ADJUSTABLE
13°40’ H1-H2= 115 mm
14°15’ H1-H2= 149 mm
Maximum left/right
difference= 1°
78423S2
PARALLELISM
(Toe-out)
Adjusted by
rotating track rod
For two wheels UNLADEN sleeves
0°10’ ± 10’ 1 turn= 30’
(1 ± 1 mm) (3 mm)
78423S
POSITION FOR TIGHTENING RUBBER BUSHES
- UNLADEN -
81603S1
07-23
VALUES AND SETTINGS
Front axle checking values 07
POWER ASSISTED STEERING
B/C/L 539 - B/C/D/L 53D
5°30’ H5-H2= 32 mm
5° H5-H2= 51 mm
4°30’ H5-H2= 70 mm NOT ADJUSTABLE
4° H5-H2= 89 mm
3°30’ H5-H2= 108 mm
Maximum left/right
difference= 1°
93012-1S
CAMBER
0°18’ H1-H2= 41 mm
- 0°15’ H1-H2= 120 mm
± 30’ NOT ADJUSTABLE
- 0°00’ H1-H2= 141 mm
1°02’ H1-H2= 185 mm
Maximum left/right
difference= 1°
93013-1S
KING PIN INCLINATION
8°40’ H1-H2= 41 mm
10°40’ H1-H2= 120 mm
± 30’ NOT ADJUSTABLE
11°00’ H1-H2= 141 mm
11°06’ H1-H2= 185 mm
Maximum left/right
difference= 1°
93014-1S
PARALLELISM
(Toe-out) Adjusted by
rotating track rod
sleeves
Foe two wheels UNLADEN 1 turn= 30’
0°10’ ± 10’ (3 mm)
(1 ± 1 mm)
93011-1S
POSITION FOR TIGHTENING RUBBER BUSHES
UNLADEN
- -
81603S1
07-24
VALUES AND SETTINGS
Rear axle checking values 07
ALL TYPES EXCEPT B/C/L 539 - B/C/D/L 53D
POSITION OF THE
VALUES ADJUSTMENT
REAR AXLE
ANGLES
Rear axle Rear axle Rear axle Rear axle Rear axle Rear axle
Tubular 4 bars Tubular 4 bars Tubular 4 bars
CAMBER
78423S1
PARALLELISM
- UNLADEN -
81603S1
07-25
VALUES AND SETTINGS
Rear axle checking values 07
B/C/L 539 - B/C/D/L 53D
93013-2S
PARALLELISM
Per wheel
- 10’ to 30’
(Toe-in) UNLADEN NOT ADJUSTABLE
or
- 1 to - 3 mm
93011-2S
POSITION FOR TIGHTENING RUBBER BUSHES
- UNLADEN -
81603S1
07-26
VALUES AND SETTINGS
Underbody heights 07
UNDERBODY HEIGHTS (1) (mm)
Tolerances : ± 7.5 mm
The differences between the right hand side and the left hand side on the same axle must not exceed 5 mm,
with the driver’s side always being the higher.
Any alteration to the underbody height must be followed by resetting of the headlight beams and the
braking compensator.
(1) If there is a minus sign in front of a value, this represents a floor position which is higher than that of the
wheel centreline in relation to the ground.
* As an option.
07-27
VALUES AND SETTINGS
Brake compensator 07
Checking pressure (Bar)
Amount of fuel in tank
Type
(driver on board)
Front Rear
B/C/L 533
53C
53Y With ABS
(after 05/92)
534
53J
53K
B/C/L 53T
With
53V ABS
53Z
+0
90966S 100 40
-8
3/4/5 53A
With
53B ABS
53F
B/C/L/S 53F
538
Without ABS
53K (before 11/94)
53T
53Z
3/4/5 53C
Without ABS
53D (before 11/94)
53H
07-28
VALUES AND SETTINGS
Brake compensator 07
Checking pressure (Bar)
Amount of fuel in tank
Type
(driver on board)
Front Rear
B/C/D/L 539 +0
(before 05/92) 100 47 -8
53D
B/C/L 53A
535
with ABS
53B
538
with ABS
B/C/L 53F (after 05/92) +0
100 52 -8
3/4/5 53C
53D with ABS
53H
90966S
B/C/L/S 53F
538
53K With ABS
(after 11/94)
53T
+0
100 49
53Z -8
3/4/5 53C
Without ABS
53D (after 11/94)
53H
07-29
VALUES AND SETTINGS
Brake compensator 07
Checking pressure (Bar)
Amount of fuel in tank
Type
(driver on board)
Front Rear
B/C/D/L/S 533
53C
53F
With ABS
534 (before 05/92)
+0
100 43
53J -8
53K
53Y
D 53V
8 53A With ABS
53F
07-30