Professional Documents
Culture Documents
LC-46/52E77U
SERVICE MANUAL
No. S37X3LC46E77U
In the interests of user safety (required by safety regulations in some countries) the set should be restored to its
original condition and only parts identical to those specified should be used.
CONTENTS
SAFETY PRECAUTION CHAPTER 7. OVERALL WIRING/SYSTEM BLOCK
IMPORTANT SERVICE SAFETY PRE- DIAGRAM
CAUTION ............................................................i [1] OVERALL WIRING DIAGRAM ......................7-1
PRECAUTIONS A PRENDRE LORS DE [2] SYSTEM BLOCK DIAGRAM .........................7-2
LA REPARATION ...............................................ii
PRECAUTIONS FOR USING LEAD-FREE CHAPTER 8. PRINTED WIRING BOARD ASSEM-
SOLDER ........................................................... iii BLIES
[1] KEY Unit ........................................................8-1
CHAPTER 1. SPECIFICATIONS [2] MAIN Unit ......................................................8-2
[1] SPECIFICATIONS ......................................... 1-1 [3] LED Unit ........................................................8-6
CHAPTER 5. ADJUSTMENT
[1] ADJUSTMENT PROCEDURE ....................... 5-1
[2] PUBLIC MODE SETTING PROCEDURE ...... 5-16
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
WARNING • Use an AC voltmeter having with 5000 ohm per volt, or higher, sen-
sitivity or measure the AC voltage drop across the resistor.
1. For continued safety, no modification of any circuit should be
attempted. • Connect the resistor connection to all exposed metal parts having a
return to the chassis (antenna, metal cabinet, screw heads, knobs
2. Disconnect AC power before servicing. and control shafts, escutcheon, etc.) and measure the AC voltage
drop across the resistor.
C A U T I O N : F O R C O N T I N U E D PROTECTION All checks must be repeated with the AC cord plug connection
AGAINST A RISK OF FIRE REPLACE ONLY WITH reversed. (If necessary, a nonpolarized adaptor plug must be used
only for the purpose of completing these checks.)
SAME TYPE FUSE.
Any reading of 0.75 Vrms (this corresponds to 0.5 mA rms AC.) or
more is excessive and indicates a potential shock hazard which
F7000 (250V 6.3A)
must be corrected before returning the monitor to the owner.
DVM
AC SCALE
BEFORE RETURNING THE RECEIVER (Fire &
Shock Hazard) 1.5k ohm
Before returning the receiver to the user, perform the following 10W
safety checks:
3. Inspect all lead dress to make certain that leads are not pinched,
and check that hardware is not lodged between the chassis and
other metal parts in the receiver.
0.15 µF
4. Inspect all protective devices such as non-metallic control knobs, TEST PROBE
insulation materials, cabinet backs, adjustment and compartment
covers or shields, isolation resistor-capacitor networks, mechanical
insulators, etc.
5. To be sure that no shock hazard exists, check for leakage current in
the following manner. TO EXPOSED CONNECT TO
• Plug the AC cord directly into a 120 volt AC outlet. METAL PARTS KNOWN EARTH
GROUND
• Using two clip leads, connect a 1.5k ohm, 10 watt resistor paral-
leled by a 0.15µF capacitor in series with all exposed metal cabinet
parts and a known earth ground, such as electrical conduit or elec-
trical ground connected to an earth ground.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICE
Many electrical and mechanical parts in LCD color television have For continued protection, replacement parts must be identical to those
special safety-related characteristics. used in the original circuit.
These characteristics are often not evident from visual inspection, nor The use of a substitute replacement parts which do not have the same
can protection afforded by them be necessarily increased by using safety characteristics as the factory recommended replacement parts
replacement components rated for higher voltage, wattage, etc. shown in this service manual, may create shock, fire or other hazards.
Replacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by " " and shaded areas in the Replacement Parts List
and Schematic Diagrams.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
i
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux
conseils suivants.
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
AVIS POUR LA SECURITE
De nombreuses pièces, électriques et mécaniques, dans les télévi- Pour assurer la protection, ces pièces doivent être identiques à celles
seur ACL présentent des caractéristiques spéciales relatives à la sé- utilisées dans le circuit d'origine. L'utilisation de pièces qui n'ont pas
curité, qui ne sont souvent pas évidentes à vue. Le degré de protec- les mêmes caractéristiques que les pièces recommandées par l'usine,
tion ne peut pas être nécessairement augmentée en utilisant des indiquées dans ce manuel, peut provoquer des électrocutions, incen-
pièces de remplacement étalonnées pour haute tension, puissance, dies, radiations X ou autres accidents.
etc.
Les pièces de remplacement qui présentent ces caractéristiques sont
identifiées dans ce manuel; les pièces électriques qui présentent ces
particularités sont identifiées par la marque " " et hachurées dans la
liste des pièces de remplacement et les diagrammes schématiques.
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
ii
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
Indicates lead-free solder of tin, silver and copper. Indicates lead-free solder of tin, silver and copper.
Soldering
• As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
• Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
PRICE PART
PARTS CODE DESCRIPTION
RANK DELIVERY
ZHNDAi123250E BL J φ0.3mm 250g (1roll)
ZHNDAi126500E BK J φ0.6mm 500g (1roll)
ZHNDAi12801KE BM J φ1.0mm 1kg (1roll)
iii
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
LC46E77U
CHAPTER 1. SPECIFICATIONS Service Manual
[1] SPECIFICATIONS
1–1
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
LC46E77U
CHAPTER 2. OPERATION MANUAL Service Manual
Part Names
TV (Front)
OPC indicator
POWER indicator
* OPC: Optical Picture Control
TV (Rear/Side)
POWER
button
MENU
button AC INPUT
terminal
INPUT
button
INPUT 7 terminal
(HDMI)
Channel
INPUT 9 terminal
buttons (HDMI)
(CH / )
INPUT 8 terminal
Volume (HDMI)
buttons
DIGITAL AUDIO
(VOL+/-) OUTPUT terminal
AUDIO OUTPUT
terminals
INPUT 5
terminal Antenna/Cable in
(HDMI)
INPUT 1 terminals
INPUT 3
terminals INPUT 2 terminals
RS-232C terminal
INPUT 4 terminal (PC-IN)
2–1
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
Part Names
QUICK REFERENCE
Attaching the Stand
• Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT terminal.
• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being damaged.
CAUTION
• Attach the stand in the correct direction.
• Do not remove the stand from the TV unless using an optional wall mount bracket to mount it.
• Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
1 Confirm that there are 8 screws (4 short screws 3 1 Insert the stand into the openings on the bottom
and 4 long screws) and a hex key supplied with the of the TV.
stand unit.
2 Insert and tighten the 4 short screws into the 4
holes on the rear of the TV.
Hex key
Long screws
2–3
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
Appendix
Removing the Stand
Before detaching (or attaching) the stand, unplug the AC cord from the AC INPUT terminal.
CAUTION
Do not remove the stand from the TV unless using an optional wall mount bracket to mount it.
Before attaching/detaching the stand
Before performing work, make sure to turn off the TV.
Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being
damaged.
1 Hex key 2
Unfasten the four screws used to secure the stand in Detach the stand from the TV. (Hold the stand so it
place. will not drop from the edge of the base area.)
Detach the cable clamp on the rear of the TV when using the optional mount bracket.
To use this TV mounted on a wall, remove the covers at the 4 locations on the rear of the TV, and then use the screws
supplied with the wall mount bracket to secure the bracket to the rear of the TV.
2–4
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
Appendix
Troubleshooting
Problem Possible Solution
No power Check if you pressed TV POWER on the remote control unit. If the indicator on the
TV does not light up, press POWER on the TV.
Is the AC cord disconnected?
Has the power been turned on?
Unit cannot be operated. External in-fluences such as lightning, static electricity, may cause improper
operation. In this case, operate the unit after first turning off the power of the TV or
unplugging the AC cord and replugging it in after 1 or 2 minutes.
Remote control unit does not Is the FUNCTION set correctly? Set it to the TV setting position.
operate. Are batteries inserted with polarity (+, -) aligned?
Are batteries worn out? (Replace with new batteries.)
Are you using it under strong or fluorescent lighting?
Is a fluorescent light illuminated near the remote control sensor?
The TV sometimes makes a This is not a malfunction. This happens when the cabinet slightly expands and
cracking sound. contracts according to change in temperature. This does not affect the TV's
performance.
Troubleshooting-Digital Broadcasting
The error message about reception of broadcast
The example of an error message
Error code Possible Solution
displayed on a screen
No broadcast now. E203 Check the broadcast time in the program guide.
2–5
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
Some menu items may not be displayed depending on the selected input source.
2–6
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
LC46E77U
CHAPTER 3. DIMENSIONS Service Manual
[1] DIMENSIONS
40 19/ 64 (1023.4)
30 31/ 64 (774)
28 5/ 32 (715)
22 43/ 64
17 21/ 64 (440)
(575.6)
2 21/ 64
(59)
20 3/ 4
4 45/ 64 3 61/ 64
15 3/ 4 (400) (119) (100)
6 57/ 64
(175)
15 3/ 4 (400)
12 13/ 16
(325)
LC-52E77U
49 3/ 8 (1254)
45 9/ 16 (1157.0)
32 9/ 64 (816)
34 9/ 64 (867)
25 41/ 64
(651.0)
19 1/ 4 (489)
2 1/ 64
(51)
21 7/ 64 (536)
5 1/ 4 4 27/ 64
15 3/ 4 (400) (133) (112)
5 23/ 32
(145)
15 3/ 4 (400)
14 17/ 32
(369)
3–1
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
LC46E77U
Service
CHAPTER 4. REMOVING OF MAJOR PARTS Manual
2. Remove the 1 lock screw , 8 lock screws , 4lock screws and detach the Rear Cabinet Ass’y.
4
Rear Cabinet Ass'y
Stand Unit
4–1
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
2. Removing of Bottom Cover, Side AV Civer, Main PWB Shield and Control Shield.
1. Detach the Bottom Cover .
3. Remove the 2 lock screws , 2 lock screws and detach the Side AV Cover Ass’y.
4. Remove the 4 lock screws , 4 lock screws , 3 lock screws and detach the Main PWB Shield.
5. Remove the 4 lock screws , and detach the Control Shield Ass’y.
Main PWB
Shield
4
Side AV Cover Ass'y SP SP
Speaker-R
2 2
Speaker-L
Bottom Cover 1
4–2
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
3. Removing of Connectors.
1. Disconnect the following connectors from MAIN Unit. (LB, LP, PD, LW, RA, KM, SP)
2. Disconnect the following connectors from POWER Unit. (LB1, PD, PL, LB2, LA)
3. Disconnect the following connectors from INVERTER-1 Unit. (LB2, LA)
4. Disconnect the following connectors from LCD Control Unit. (LP, LW, PL)
INVERTER-1 Unit
LB2
LB2
LA
LB1
PD LA
PL
LP
PD
LB
LW
KM
LP LW PL
RA SP
4–3
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
4. Removing of POWER Unit , MAIN Unit, KEY Unit Ass’y and R/C, LED Unit.
1. Remove the 6 lock screws and detach the POWER Unit.
4. Detach the KEY Unit From Operation Button and disconnect KM wire .
KEY Unit
4
KM
Operation
Button
RA
5
R/C, LED Unit
1
POWER Unit
MAIN Unit
4–4
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
5. Removing of Main PWB Angle, Panel Support Angle, Barrier Sheet and LCD Panel Module Unit.
1. Remove the 1 lock screw and detach the Main PWB Angle.
2. Detach the Barrier Sheet from Panel Support Angle. Remove the 16 lock screws and detach the Panel Support Angle.
3. Remove the 8 lock screws and detach the LCD Panel Module Unit.
Barrier Sheet
2 2
3
Panel Support Angle
4–5
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
6. Removing of LCD Panel Module.
1. Remove the 14 lock screws , 2 lock screws and detach the Bezel Ass’y .
3. Detach the 2 pieces Lamp Holder , Socket and detach the following 18 pieces Lamp from BL Chassis Ass'y .
9 BL Chassis Ass'y
8 Socket
6 Lamp Holder
7 Lamp
6 Lamp Holder
1 5 Diffusion Plate
4 Lens Sheet
3 Bezel Ass'y
2
4–6
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
[2] REMOVING OF MAJOR PARTS (LC-52E77U)
1. Removing of Stand Unit and Rear Cabinet Ass’y.
1. Remove the 4 lock screws and detach the Stand Unit .
2. Remove the 1 lock screw , 12 lock screws , and detach the Rear Cabinet Ass’y.
3
Rear Cabinet Ass'y
Stand Unit
4–7
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
2. Removing of Bottom Cover, Side AV Civer, Main PWB Shield and Control Shield.
1. Detach the Bottom Cover .
3. Remove the 2 lock screws , 2 lock screws and detach the Side AV Cover Ass’y.
4. Remove the 4 lock screws , 4 lock screws , 3 lock screws and detach the Main PWB Shield.
5. Remove the 4 lock screws , and detach the Control Shield Ass’y.
8
3
Main PWB
Shield Control Shield Ass'y
4
Side AV Cover Ass'y
SP SP
Speaker-R
2 2
4–8
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
3. Removing of Connectors.
1. Disconnect the following connectors from MAIN Unit. (LB, LP, PD, LW, RA, KM, SP)
2. Disconnect the following connectors from POWER Unit. (LB1, PD, PL, LB2, LA)
3. Disconnect the following connectors from INVERTER-1 Unit. (LB2, LA)
4. Disconnect the following connectors from LCD Control Unit. (LP, LW, PL)
LB2
LA
PL LW LP
LB2
LB1
PD LA
PL
LP
PD
LB
LW
KM
RA SP
4–9
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
4. Removing of POWER Unit , MAIN Unit, KEY Unit Ass’y and R/C, LED Unit.
1. Remove the 6 lock screws and detach the POWER Unit.
4. Detach the KEY Unit From Operation Button and disconnect KM wire .
KEY Unit
4
KM
Operation
Button
RA
5
R/C, LED Unit
POWER Unit
MAIN Unit
4 – 10
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
5. Removing of Main PWB Angle, Panel Support Angle, Barrier Sheet and LCD Panel Module Unit.
1. Remove the 1 lock screw and detach the Main PWB Angle.
2. Remove the 14 lock screws and detach the Panel Support Angle.
3. Remove the 8 lock screws , 10 lock screws and detach the Corner Lug (UP) , Center Lug and Corner Lug .
2 2
8
LCD Panel Module Unit
4 3 4 3 3 4 3 4
6 Center Lug 6 Center Lug
7 Corner Lug 7 Corner Lug
4 – 11
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
6. Removing of LCD Panel Module.
1. Remove the 16 lock screws , 2 lock screws and detach the Bezel Ass’y .
3. Detach the 2 pieces Lamp Holder , Socket and detach the following 18 pieces Lamp from BL Chassis Ass'y .
9 BL Chassis Ass'y
8 Socket
6 Lamp Holder
1 7 Lamp
6 Lamp Holder
1 5 Diffusion Plate
4 Lens Sheet
3 Bezel Ass'y
2
4 – 12
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
LC46E77U
CHAPTER 5. ADJUSTMENT Service Manual
1. After replacement of any PWB unit and/or IC for repair, please note the following.
• When replacing the following units, make sure to prepare the new units loaded with updated software.
MAIN Unit: DUNTKE833FM03
• When replacing the LCD control PWB, perform the VCOM adjustment.
2.2.2 Preparations
To upgrade the main software, it is necessary to get ready the USB Memory for version upgrade before you start.
Follow the steps below and create the USB Memory for version upgrade.
1. Copy the file HLNAAxxx.USB for version upgrade to the root directory (folder) of the USB Memory.
NOTE: In the USB Memory drive, do not store other folders or unrelated files, or more than one file for version upgrade.
Now the USB Memory for version upgrade is ready.
E77U
5–1
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
5. Even a single failure in the process will trigger the upgrade failure screen.
E77U
NOTE: In the event of a failure, repeat the upgrade process. If the process repeatedly fails, it is likely that the hardware need fixing.
6. Upon completion of the whole process, the upgrade success screen as shown below appears. You can check the new software version on this
screen. The version information appears after the upgrade is complete.
E77U
7. Unplug the AC cord and remove the USB Memory for version upgrade.
8. Now the software version upgrade is complete.
NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the main
software version information.
5–2
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
2.3. Monitor microprocessor software version upgrade
Create the USB memory for monitor microprocessor software version upgrade in the same manner as explained in the “Main software version
upgrade”.
Copy the file HLNAVAxx.USB and HLNAMxxx.BIN (named temporarily) for monitor microprocessor software version upgrade to the USB memory.
E77U
6. If the upgrade fails, power led will stop blinking. Also, the upgrade failure screen will be shown if upgrade screen was shown at 5.
E77U
NOTE: In the event of a transient failure, upgrade will be automatically retried up to three times. If the process repeatedly fails, hardware may be the
cause.
7. Up on completion of the whole process, power and OPC LED will blink alternately. Also, the upgrade success screen will be shown if upgrade
screen was shown at 5.
E77U
8. Unplug the AC cord and remove the USB Memory for version upgrade.
9. Now the software version upgrade is complete.
NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the mon-
itor microprocessor software version information and panel size information.
5–3
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
3. Entering and exiting the adjustment process mode
1) Before entering the adjustment process mode, the AV position RESET in the video adjustment menu.
2) While holding down the “VOL (–)” and “INPUT” keys at a time, plug in the AC cord of the main unit to turn on the power.
The letter “<K>” appears on the screen.
3) Next, hold down the “VOL (–)” and “CH ( )” keys at a time.
(The “VOL (–)” and “CH ( )” keys should be pressed and held until the display appears.)
Multiple lines of blue characters appearing on the display indicate that the unit is now in the adjustment process mode.
When you fail to enter the adjustment process mode (the display is the same as normal startup), retry the procedure.
4) To exit the adjustment process mode after the adjustment is done, unplug the AC cord from the outlet to make a forced shutdown. (When the
power was turned off with the remote controller, once unplug the AC cord and plug it again. In this case, wait 10 seconds or so before plugging.)
CAUTION: Use due care in handling the information described here lest your users should know how to enter the adjustment process mode. If the
settings are tampered in this mode, unrecoverable system damage may result.
4. Remote controller key operation and description of display in adjustment process mode
1) Key operation
*Input mode is switched automatically when relevant adjustment is started so far as the necessary input signal is available.
2) Description of display
(2) Current selected input
(3) Current color system
(5) LCD Panel size/Speaker type
(1) Current page/ (4) Destination
Total pages
5–4
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
5. List of adjustment process mode menu
The character string in brackets [ ] will appear as a page title in the adjustment process menu header.
5–5
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
Page Line Item Description Remarks (adjustment detail, etc.)
7 1 ANALOG RGB ADJ Analog RGB picture level adjustment
2 R A_GAIN
3 G A_GAIN
4 B A_GAIN
5 R D_GAIN
6 G D_GAIN
7 B D_GAIN
8 R OFFSET
9 G OFFSET
10 B OFFSET
8 1 VCOM ADJ VCOM adjustment value
9 1 FRC ON/OFF
2 LEV1 Standard value 1 Adjustment gradation setting.
3 LEV2 Standard value 2
4 LEV3 Standard value 3
5 LEV4 Standard value 4
6 LEV5 Standard value 5
7 LEV6 Standard value 6
10 1 MG1R WB adjustment Point 1, R adjustment value Parameter for six-point adjustment
2 MG1G WB adjustment Point 1, G adjustment value
3 MG1B WB adjustment Point 1, B adjustment value
4 MG2R WB adjustment Point 2, R adjustment value
5 MG2G WB adjustment Point 2, G adjustment value
6 MG2B WB adjustment Point 2, B adjustment value
7 MG3R WB adjustment Point 3, R adjustment value
8 MG3G WB adjustment Point 3, G adjustment value
9 MG3B WB adjustment Point 3, B adjustment value
11 1 MG4R WB adjustment Point 4, R adjustment value Parameter for six-point adjustment
2 MG4G WB adjustment Point 4, G adjustment value
3 MG4B WB adjustment Point 4, B adjustment value
4 MG5R WB adjustment Point 5, R adjustment value
5 MG5G WB adjustment Point 5, G adjustment value
6 MG5B WB adjustment Point 5, B adjustment value
7 MG6R WB adjustment Point 6, R adjustment value
8 MG6G WB adjustment Point 6, G adjustment value
9 MG6B WB adjustment Point 6, B adjustment value
12 1 MODE SELECT
2 POS SELECT
3 POS MIN
4 POS MID1
5 POS MID2
6 POS MID3
7 POS MID4
8 POS MID5
9 POS MID6
10 POS MAX
13 1 CD MIN
2 CD MID1
3 CD MID2
4 CD MID3
5 CD MID4
6 CD MID5
7 CD MID6
8 CD MAX
14 1 CALC
2 RESET
3 VAL1
4 VAL2
5 VAL3
6 VAL4
7 VAL5
8 VAL6
5–6
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
Page Line Item Description Remarks (adjustment detail, etc.)
15 1 Audio Switch
2 Flat Mode
3 ADC Volume 1
4 ADC Volume 2
5 ADC Volume 3
6 ADC Volume 4
7 ADC Volume 5
8 ADC Volume 6
16 1 Lip Sync LR
2 Lip Sync Monitor
3 Lip Sync SW
4 LR Func Vol AIN(2ch)
5 LR Func Vol HDMI(2ch)
6 LR Func Vol ATV(2ch)
7 LR Func Vol DTV(2ch)
8 Input Trim(2ch)
17 1 PEQ1 F0
2 PEQ1 Q
3 PEQ1 Gain
4 PEQ1 Gain Limit
5 PEQ1 Fade Time
6 PEQ2 F0
7 PEQ2 Q
8 PEQ2 Gain
9 PEQ2 Gain Limit
10 PEQ2 Fade Time
18 1 PEQ3 F0
2 PEQ3 Q
3 PEQ3 Gain
4 PEQ3 Gain Limit
5 PEQ3 Fade Time
6 PEQ4 F0
7 PEQ4 Q
8 PEQ4 Gain
9 PEQ4 Gain Limit
10 PEQ4 Fade Time
19 1 PEQ5 F0
2 PEQ5 Q
3 PEQ5 Gain
4 PEQ5 Gain Limit
5 PEQ5 Fade Time
6 PEQ6 F0
7 PEQ6 Q
8 PEQ6 Gain
9 PEQ6 Gain Limit
10 PEQ6 Fade Time
20 1 PEQ7 F0
2 PEQ7 Q
3 PEQ7 Gain
4 PEQ7 Gain Limit
5 PEQ7 Fade Time
6 Subsonic Filter
21 1 Output Trim
2 Clipper
3 Sub Volume Default
4 Sub Volume SH Bass
5 Mon Func Vol AIN
6 Mon Func Vol HDMI
7 Mon Func Vol ATV
8 Mon Func Vol DTV
9 SW Func Vol AIN
10 SW Func Vol HDMI
11 SW Func Vol ATV
12 SW Func Vol DTV
5–7
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
Page Line Item Description Remarks (adjustment detail, etc.)
22 1 BE ATT
2 BE G Limit
3 Bass Center ATT
4 Bass Vol0 MIN
5 Bass Vol60 MIN
6 Bass Vol60 Center
7 Bass Vol0 MAX
8 Bass Vol60 MAX
23 1 Treble Center ATT
2 Treble Vol0 MIN
3 Treble Vol60 MIN
4 Treble Vol60 Center
5 Treble Vol0 MAX
6 Treble Vol60 MAX
7 VS Path
8 VS Option
9 VS SP Interval
10 VS Width
11 VS Input Gain(2ch)
24 1 Bass AGC
2 Bass Harmonics
3 Bass LPF Fc
4 Bass HPF Fc
5 Bass AGC Max
6 Bass AGC Min
7 Bass AGC Attack Time
8 Bass AGC Release Time
9 Bass AGC Threshold
10 Bass AGC HPF F0
11 Bass Harmonics Level
12 Bass Harmonics LPF F
13 Bass Harmonics HPF F
25 1 PANNEL SELECT
2 PWM
3 PWM FREQ
4 PWM DUTY
5 OSC FREQ
6 OSC DUTY
26 1 BRIGHTNESS DA0
2 BRIGHTNESS DA1
3 BRIGHTNESS DA2
4 BRIGHTNESS DA3
5 BRIGHTNESS DA4
6 BRIGHTNESS DA5
7 BRIGHTNESS DA6
8 BRIGHTNESS DA7
9 BRIGHTNESS DA8
10 BRIGHTNESS DA9
11 BRIGHTNESS DA10
12 BRIGHTNESS DA11
27 1 BRIGHTNESS DA12
2 BRIGHTNESS DA13
3 BRIGHTNESS DA14
4 BRIGHTNESS DA15
5 BRIGHTNESS DA16
6 BRIGHTNESS DA17
7 BRIGHTNESS DA18
8 BRIGHTNESS DA19
9 BRIGHTNESS DA20
10 BRIGHTNESS DA21
11 BRIGHTNESS DA22
5–8
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
Page Line Item Description Remarks (adjustment detail, etc.)
28 1 BRIGHTNESS DA23
2 BRIGHTNESS DA24
3 BRIGHTNESS DA25
4 BRIGHTNESS DA26
5 BRIGHTNESS DA27
6 BRIGHTNESS DA28
7 BRIGHTNESS DA29
8 BRIGHTNESS DA30
9 BRIGHTNESS DA31
10 BRIGHTNESS DA32
29 1 OPC33 ADLEVEL 0
2 OPC33 ADLEVEL 1
3 OPC33 ADLEVEL 2
4 OPC33 ADLEVEL 3
5 OPC33 ADLEVEL 4
6 OPC33 ADLEVEL 5
7 OPC33 ADLEVEL 6
8 OPC33 ADLEVEL 7
9 OPC33 ADLEVEL 8
10 OPC33 ADLEVEL 9
11 OPC33 ADLEVEL 10
12 OPC33 ADLEVEL 11
30 1 OPC33 ADLEVEL 12
2 OPC33 ADLEVEL 13
3 OPC33 ADLEVEL 14
4 OPC33 ADLEVEL 15
5 OPC33 ADLEVEL 16
6 OPC33 ADLEVEL 17
7 OPC33 ADLEVEL 18
8 OPC33 ADLEVEL 19
9 OPC33 ADLEVEL 20
10 OPC33 ADLEVEL 21
11 OPC33 ADLEVEL 22
31 1 OPC33 ADLEVEL 23
2 OPC33 ADLEVEL 24
3 OPC33 ADLEVEL 25
4 OPC33 ADLEVEL 26
5 OPC33 ADLEVEL 27
6 OPC33 ADLEVEL 28
7 OPC33 ADLEVEL 29
8 OPC33 ADLEVEL 30
9 OPC33 ADLEVEL 31
32 1 V6 OS THERMO 1
2 V6 OS THERMO 2
3 V6 OS THERMO 3
4 V6 OS THERMO 4
5 V6 OS THERMO 5
6 V6 OS THERMO 6
7 V6 OS THERMO 7
33 1 V5 OS THERMO 1
2 V5 OS THERMO 2
3 V5 OS THERMO 3
4 V5 OS THERMO 4
5 V5 OS THERMO 5
6 V5 OS THERMO 6
7 V5 OS THERMO 7
34 1 BL TEMP1
2 BL TEMP2
3 BL TDUTY
35 1 MONITOR TIME OUT
2 MONITOR MAX TEMP
3 MONITOR ERROR CAUSE
RESET
5–9
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
Page Line Item Description Remarks (adjustment detail, etc.)
36 1 LCD TEST PATTERN
2 TV TEST PATTERN 1
3 TV TEST PATTERN 2
37 1 KEY LOCK(1217)
2 KOUTEI AREA ALL CLEAR
3 A MODE AREA CLEAR
4 BACKUP AREA CLEAR
5 B MODE AREA CLEAR
6 EXECUTION
38 1 READ/WRITE
2 SLAVE ADDRESS
3 REGISTER ADDRESS UPPER
4 REGISTER ADDRESS LOWER
5 WRITE DATA UPPER
6 WRITE DATA LOWER
7 READ DATA UPPER
8 READ DATA LOWER
39 1 EEP SAVE Writing setting values to EEPROM
2 EEP RECOVER Reading setting values from EEPROM
3 STANDBY CAUSE RESET Reset stand by cause
4 SETTING FOR ADJ
40 1 BD UNIT FACTORY MENU
5 – 10
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
6. Special features
* STANDBY CAUSE (Page 1/40)
Display of a cause (code) of the last standby
The cause of the last standby is recorded in EEPROM whenever possible.
Checking this code will be useful in finding a problem when you repair the troubled set.
* EEP SAVE (Page 39/40)
Storage of EEP adjustment value
* EEP RECOVER (Page 39/40)
Retrieval of EEP adjustment value from storage area
2 Auto adjustment Page 3/40 Bring the cursor on [•N358 ALL ADJ (INPUT1)] and press [ENTER].
performance [•N358 ALL ADJ (INPUT1) OK] appears when finished.
100% white
2 Auto adjustment Page 5/40 Bring the cursor on [•COMP 15K ADJ (INPUT1)] and press [ENTER].
performance [•COMP 15K ADJ (INPUT1) OK] appears when finished.
5 – 11
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
7.5. Component 33K signal adjustment
100% white
2 Auto adjustment Page 6/40 Bring the cursor on [•COMP 33K ADJ (INPUT1)] and press [ENTER].
performance [•COMP 33K ADJ (INPUT1) OK] appears when finished.
2 Auto adjustment Bring the cursor on [•ANALOG RGB ADJ] and press [ENTER].
performance [•ANALOG RGB ADJ OK] appears when finished.
5 – 12
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
8. Adjustment of white balance
8.1. White balance adjustment
Point 1
WBI10184
MG1G****
MG1B****
MG1R****
Writing
MSET0003
5 – 13
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
8.2. Adjusting procedure by use of [RS-232C]
1. Get ready the PC with COM port (RS-232C) running on Windows 95/98/ME/2000/XP operating system, as well as the RS-232C cross cable.
2. Start the unit with the RS-232C cable connected.
3. Start the terminal software. (The freeware readily available on the Internet will do.)
4. Make the following settings.
5. If the settings are correct, the terminal software indicates “ERR” against pressing of the “ENTER” key.
6. After the settings are done correctly, it is possible to make an adjustment by typing in the command shown in the table below and pressing the
“ENTER” key on the keyboard.
7. Command entry is successful if the terminal software indicates “OK” when the “ENTER” is pressed. If “ERR” is shown, retry to enter the command.
8. Send the process mode switching command to switch from the RS232C operation mode to the process mode.
KRSW0001: “ERR” is returned.
KKT10037: When “OK” is returned, the process mode becomes active. When “ERR”, start over from KRSW0001.
9. Send each adjustment command.
5 – 14
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
10. Model number ID plug
Model numbers are identified by inserting the destination ID plug (QCNCMA275WJQZ) in its specified slot of the destination ID connector SC9201/
SC9202 (QCNCWA715WJQZY).
1 㽲
1 䇼KM䇽 㽳
4 HDMI MAIN Unit
E833 41 㽴
䇼LW䇽
㽵
㽶
HDMI
㽷
㽸
PC Audio IN
Optical TUNER
OUT L/R
S-video 㽹
V/LR
USB
䇼RA䇽 䇼SP䇽
RS-232C 10 1 4
Analog RGB
1
5 – 15
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
[2] PUBLIC MODE SETTING PROCEDURE
1. How to start Public Mode
• There are the following two ways to get the public mode setup screen displayed.
In the adjustment process mode, turn on “PUBLIC MODE”. Also press the “CH ( )” and “VOL (+)” keys on the set at once and turn on the
power.
1) Press the “INPUT” and “VOL (+)” keys on the set at once and turn on the power.
2) Get the password input screen displayed.
Procedure
˴The input starts with the leftmost digit.
˴Use the numeric keys [1] thru [9] and [0] keys on the remote controller.
˴The other keys are not acceptable.
˴With a numeric-key input, "_" will change to "˴".
˴The input position will move one digit to the right.
˴With all the 3 digits entered, the password will be verified.
5 – 16
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
4. Public Mode Menu
The guidance is not displayed on screen.
Setup procedure
• To move the cursor up and down, use the “cursor UP/DOWN” key (remote controller) and “CH ( )/( )” key (remote controller and set).
• To change the settings, use the “cursor RIGHT/LEFT” key (remote controller) and “VOL (+)/(–)” key (remote controller and set).
• To save new settings, keep the cursor at “EXECUTE” and use “ENTER” key (remote controller and set).
PUBLIC MODE
POWER ON FIXED [VARIABLE ]
MAXIMUM VOLUME [ 60 ]
VOLUME FIXED [VARIABLE ]
VOLUME FIXED LEVEL [ 20 ]
RC BUTTON [RESPOND ]
PANEL BUTTON [RESPOND ]
MENU BUTTON [RESPOND ]
AV POSITION FIXED [VARIABLE ]
ON SCREEN DISPLAY [YES ]
INPUT MODE START [NORMAL ]
INPUT MODE FIXED [VARIABLE ]
LOUD SPEAKER [ON ]
RC_PATH_THROUGH [OFF ]
232C POWON [DISABLE ]
PUBLIC MODE [OFF ]
RESET
EXECUTE
5 – 17
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
5. On Setting Items
* “EZ-SETUP” discussed below indicates “EZ-SETUP after the first power-on”.
1) POWER ON FIXED
2) MAXIMUM VOLUME
3) VOLUME FIXED
Selection Selection between “Variable”, “Fixed”, “ACON (AC CTRL)” and “AC/RCON (AC/RC CTRL)” (loop provided)
Default Variable
Explanation • FIXED: Fixed at the level adjusted for a fixed volume.
• AC CTRL: Start-up at the level specified for a fixed volume at ACON.
• AC/RC CTRL: Start-up at the level specified for a fixed volume at start.
Limit in Setting • The sound volume for the ON-timer (Wake up timer) is fixed also without display of menu. Besides, the setting is made
impossible. (Basically, the menu is not displayed.)
• The following keys become invalid:
• Sound volume Up/Down (VOL +/–) [for both remote control and the unit]
• Mute (MUTE)
Exception • In the item “VOLUME” of adjustment process, the sound volume can be set freely irrespective of this setting.
Remarks • As for sound volume fixing and sound volume MAX level, the sound volume fixing has priority.
• Once the sound volume has been changed by adjustment process, it should be set back to the sound volume preset by
sound volume fixing level when the adjustment process ends.
5) R/C BUTTON
Selection Selection between “Respond”, “No Respond” and “Limited” (loop provided)
Default Respond
Explanation Making the remote controller settings.
• At the “No Respond” setting, the remote controller keys are disabled. Its power key (reception/standby key) is disabled too.
• At the “Limited” setting, some channel-related keys alone are operative. All the other remote controller keys (power, volume
/ , channel / , light control (brightness sensor), broadcast select) are inoperative.
Limit in Setting In “No respond” setting, all the keys (including the power key) are not accepted.
Exception • Adjustment process, inspection process and hotel only keys are valid irrespective of setting.
• All the keys can be used in adjustment process, inspection mode and hotel menu irrespective of setting.
Remarks
5 – 18
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
6) PANEL BUTTON
7) MENU BUTTON
8) ON SCREEN DISPLAY
Selection Selection between “Normal”, “Air ( )”, “INPUT 1/2/3”, “PC”, “HDMI 1/2/3/4/5”, “DVI” (loop provided)
Default Normal
Explanation In power-ON, the input source to be started or channel can be set.
(In standard mode, the operation follows the last memory.)
About options • All the input sources in the model are made selectable.
• In TV mode, the channel to be set follows the last memory and the content of the last memory is included in the notation by
options. Ex.) Air (2), Cable (98.1) etc.
Limit in Setting • The display of channel setting menu and the channel setting operation are prohibited.
Exception
Remarks • In setting at “Normal”, the setting of “Input mode fixed” is changed to “Variable” and selection should be prohibited.
5 – 19
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
10)INPUT MODE FIXED
Selection Selection between “Variable”, “Fixed”, “ACON (AC CTRL)” and “AC/RCON (AC/RC CTRL)” (loop provided)
Default – (Variable)
Explanation • At the “Fixed” setting, the TV set gets started with the settings of “Input mode start”, and then any other channels and inputs
are not accepted.
• At the “ACON (AC CTRL)” setting, the TV set gets started with the settings of “Input mode start” under AC control.
• At the “AC/RCON (AC/RC CTRL)” setting, the TV set gets started with the settings of “Input mode start” under either control.
Limit in Setting • With the execution of hotel mode, the input source is forced to change to that set by “Input mode start” and the channel
switching and input switching are prohibited thereafter.
• ON-timer's (Wake-up timer) channel items are not displayed or the operation is prohibited. (Basically, they are not displayed.)
• The following keys are invalidated.
CH / , direct tuning button, FLASHBACK, input
However, the keys (input switching and CH / keys) of the unit for menu operation remain valid.
Exception None
Remarks • In the following case, setting is cancelled and mode is changed to “Variable”.
When the setting of “Input mode start” is set to “Normal”.
11)RC_PATH_THROUGH
Selection Selection between “OFF”, “ON: TV RCE” and “ON: TV RCD” (loop provided)
Default OFF
Explanation Function to feed the remote controller-received signal to Pin 9 (open) on the RS232C.
Limit in Setting None
Exception None
Remarks None
14)232C POWON
5 – 20
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
15)PUBLIC MODE (ON/OFF)
5 – 21
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
LC46E77U
Service
CHAPTER 6. TROUBLESHOOTING TABLE Manual
COMPOSITE: No external input video [INPUT-1] COMPOSITE: No external input video [INPUT-3]
Is INPUT-1 selected on the input select menu screen? Is INPUT-3 selected on the input select menu screen?
NO NO
Select INPUT-1 on the input select menu Select INPUT-3 on the input select menu screen
screen for the right input signal. for the right input signal.
Does the INPUT-1 V1_PLUG detection func- Does the INPUT-3 V3_PLUG detection function?
tion?
Check the line between pin (2) of input terminal Check the line between pin (7) of input terminal
(J507) and pin (AJ1) of IC8001 (CPU). (J501) and pin (AJ2) of IC8001 (CPU).
YES YES
Is there the COMPOSITE signal input at pin (AE28) of IC8001 Is there the COMPOSITE signal input at pin (AE29) of IC8001 (CPU)?
(CPU)?
NO NO
Check the line between pin (3) of J507 and pin Check the line between pin (6) of J501 and pin
(AE28) of IC8001. (AE29) of IC8001.
YES YES
Are the LVDS signal outputs at the LVDS 1st channel and 2nd channel of IC8001? NO Check IC8001 and its peripheral circuits.
LVDS_TX_0_DATA0_P/N (C14/D14), LVDS_TX_0_DATA1_P/N (C15/D15), (IC8152/IC8153, etc.)
LVDS_TX_0_DATA2_P/N (C16/D16), LVDS_TX_0_DATA3_P/N (C18/D18),
LVDS_TX_0_DATA4_P/N (C19/D19), LVDS_TX_0_CLK_P/N (C17/D17),
LVDS_TX_1_DATA0_P/N (A14/B14), LVDS_TX_1_DATA1_P/N (A15/B15),
LVDS_TX_1_DATA2_P/N (A16/B16), LVDS_TX_1_DATA3_P/N (A18/B18),
LVDS_TX_1_DATA4_P/N (A19/B19), LVDS_TX_1_CLK_P/N (A17/B17).
YES
Check the panel module.
6–1
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
No video (2)
COMPONENT: No external input video [INPUT-1] COMPONENT: No external input video [INPUT-2]
Is INPUT-1 selected on the input select menu screen? Is INPUT-2 selected on the input select menu screen?
Is the INPUT-SELECT for the input signal? Is the INPUT-SELECT for the input signal?
NO NO
Select INPUT-1 on the input select menu screen for Select INPUT-2 on the input select menu screen for
the right input signal. the right input signal.
Does the INPUT-1 C1_PLUG detection function? Does the INPUT-2 C2_PLUG detection function?
Check the line between pin (2) of input terminal (J508) Check the line between pin (2) of input terminal
and pin (AF7) of IC8001 (CPU). (J502) and pin (AH2) of IC8001 (CPU).
YES YES
Are there the COMPONENT video signal inputs at pins (AJ21) (Y)/ Are there the COMPONENT video signal inputs at pins (AJ18) (Y)/(AJ19)
(AJ22) (Pb) and (AH22) (Pr) of IC8001 (CPU)? (Pb) and (AH19) (Pr) of IC8001 (CPU)?
NO NO
Check the line between the input terminals of J508 Check the line between the input terminals of J502
and IC8001. and IC8001.
J508 pin (3) (Y) pin (5) (Pb) pin (7) (Pr) J508 pin (3) (Y) pin (5) (Pb) pin (7) (Pr)
IC8001 pin (AJ21) pin (AJ22) pin (AH22) IC8001 pin (AJ18) pin (AJ19) pin (AH19)
YES YES
Are the LVDS signal outputs at the LVDS 1st channel and 2nd channel of NO Check IC8001 and its peripheral circuits.
IC8001? (IC8152/IC8153, etc.)
LVDS_TX_0_DATA0_P/N (C14/D14), LVDS_TX_0_DATA1_P/N (C15/D15),
LVDS_TX_0_DATA2_P/N (C16/D16), LVDS_TX_0_DATA3_P/N (C18/D18),
LVDS_TX_0_DATA4_P/N (C19/D19), LVDS_TX_0_CLK_P/N (C17/D17),
LVDS_TX_1_DATA0_P/N (A14/B14), LVDS_TX_1_DATA1_P/N (A15/B15),
LVDS_TX_1_DATA2_P/N (A16/B16), LVDS_TX_1_DATA3_P/N (A18/B18),
LVDS_TX_1_DATA4_P/N (A19/B19), LVDS_TX_1_CLK_P/N (A17/B17).
YES
Check the panel module.
6–2
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
No video (3)
NO
Does the INPUT-2 S1_PLUG detection function?
Check the line between pin (6) of input terminal (J504)
and pin (AH1) of IC8001 (CPU).
YES
Are there the S-VIDEO signal inputs at pins (AF30) (Y) and (AF29) (C) of
IC8001 (CPU)?
NO
Check the line between pins (3) (Y)/(4) (C) of J504 and
pins (AF30)/(AF29) of IC8001. (Q519 and Q520, etc.)
YES
Are the LVDS signal outputs at the LVDS 1st channel and 2nd channel of IC8001? NO Check IC8001 and its peripheral circuits.
LVDS_TX_0_DATA0_P/N (C14/D14), LVDS_TX_0_DATA1_P/N (C15/D15), (IC8152/IC8153, etc.)
LVDS_TX_0_DATA2_P/N (C16/D16), LVDS_TX_0_DATA3_P/N (C18/D18),
LVDS_TX_0_DATA4_P/N (C19/D19), LVDS_TX_0_CLK_P/N (C17/D17),
LVDS_TX_1_DATA0_P/N (A14/B14), LVDS_TX_1_DATA1_P/N (A15/B15),
LVDS_TX_1_DATA2_P/N (A16/B16), LVDS_TX_1_DATA3_P/N (A18/B18),
LVDS_TX_1_DATA4_P/N (A19/B19), LVDS_TX_1_CLK_P/N (A17/B17).
YES
Check the panel module.
6–3
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
No video (4)
No video at UHF/VHF broadcast signal reception No video at digital broadcast signal reception
Is there the analog video signal output (VIDEO) at pin (19) of tuner Are there the video signal outputs (IF_P/N) at the pins (12) and (13) of
(TU1101)? tuner (TU1101)?
NO NO
Check TU1101 and its peripheral circuits Check TU1101 and its peripheral circuits
(TUN_SDA: Pin8 of TU1101 (TUN_SDA: Pin8 of TU1101
TUN_SCL: Pin9 of TU1101, etc.). TUN_SCL: Pin9 of TU1101, etc.).
YES YES
Is there the analog video signal input at pin (AD29) of IC8001 Are there the video signal inputs at pin (AA29) and (AB29) of IC8001
(CPU)? (CPU)?
NO NO
Check the line between IC8001 and TU1101, Check the line between IC8001 and TU1101, and
and their peripheral circuits. their peripheral circuits (C1129/C1130, etc.).
YES YES
Are the LVDS signal outputs at the LVDS 1st channel and 2nd channel of IC8001? NO Check IC8001 and its peripheral circuits.
LVDS_TX_0_DATA0_P/N (C14/D14), LVDS_TX_0_DATA1_P/N (C15/D15), (IC8152/IC8153, etc.)
LVDS_TX_0_DATA2_P/N (C16/D16), LVDS_TX_0_DATA3_P/N (C18/D18),
LVDS_TX_0_DATA4_P/N (C19/D19), LVDS_TX_0_CLK_P/N (C17/D17),
LVDS_TX_1_DATA0_P/N (A14/B14), LVDS_TX_1_DATA1_P/N (A15/B15),
LVDS_TX_1_DATA2_P/N (A16/B16), LVDS_TX_1_DATA3_P/N (A18/B18),
LVDS_TX_1_DATA4_P/N (A19/B19), LVDS_TX_1_CLK_P/N (A17/B17).
YES
Check the panel module.
6–4
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
No video (5)
NO
Select INPUT-4 on the input select menu screen for the right input signal.
Is IC1809 (EEPROM) accessed by I2C, with PC connected, to read the DDC_I2C SCL/SDA data?
Check the DDC line and its peripheral circuits. (IC1809 and its peripherals).
YES
Are there the video signal inputs at pins (AK16) (G), (AH15) (B) and (AK17) (R) of IC8001 (CPU)?
Are there the VSYNC/HSYNC signal inputs at pins (AJ14) and (AK14) of IC8001?
NO
Check the line between SC1804 and IC8001 (IC1802, etc.).
YES
Are the LVDS signal outputs at the LVDS 1st channel and 2nd channel of IC8001?
LVDS_TX_0_DATA0_P/N (C14/D14), LVDS_TX_0_DATA1_P/N (C15/D15),
LVDS_TX_0_DATA2_P/N (C16/D16), LVDS_TX_0_DATA3_P/N (C18/D18),
LVDS_TX_0_DATA4_P/N (C19/D19), LVDS_TX_0_CLK_P/N (C17/D17),
LVDS_TX_1_DATA0_P/N (A14/B14), LVDS_TX_1_DATA1_P/N (A15/B15),
LVDS_TX_1_DATA2_P/N (A16/B16), LVDS_TX_1_DATA3_P/N (A18/B18),
LVDS_TX_1_DATA4_P/N (A19/B19), LVDS_TX_1_CLK_P/N (A17/B17).
NO
Check IC8001 and its peripheral circuits. (IC8152/IC8153, etc.)
YES
Check the panel module.
6–5
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
HDMI: No external input video [INPUT-5] HDMI: No external input video [INPUT-7]
Is INPUT-5 selected on the input select menu screen? Is INPUT-7 selected on the input select menu screen?
NO NO
Select INPUT-5 on the input select menu screen for the Select INPUT-7 on the input select menu screen for the
right input signal. right input signal.
YES YES
Does the HOT PLUG detection function? Does the HOT PLUG detection function?
Does the DDC5V signal come from pin (18) of SC1601 to pin (36) of Does the DDC5V signal come from pin (18) of SC1602 to pin (42) of
IC1605 (HDMI_SW1)? IC1605 (HDMI_SW1)?
NO NO
Check the line between the input terminals of SC1601 Check the line between the input terminals of SC1601
and IC1605. and IC1605.
Check IC1605 and its peripheral circuits Check IC1605 and its peripheral circuits
(SDA1: pin53 of IC1605/SCL1: pin54 of IC1605, etc.). (SDA1: pin53 of IC1605/SCL1: pin54 of IC1605, etc.).
YES YES
Does the HPD signal come from pin (35) of IC1605 to pin (19) of Does the HPD signal come from pin (41) of IC1605 to pin (19) of
SC1601? SC1602?
NO NO
Check the line between the pin (35) of IC1605 and the Check the line between the pin (41) of IC1605 and the
pin (19) of SC1601. pin (19) of SC1601.
Check IC1605 and its peripheral circuits Check IC1605 and its peripheral circuits
(SDA1: pin53 of IC1605/SCL1:pin54 of IC1605, etc.). (SDA1: pin53 of IC1605/SCL1: pin54 of IC1605, etc.).
YES YES
Are there the TMDS signal inputs at pins (1/2) (CLK-/+), (3/4) (D0-/ Are there the TMDS signal inputs at pins (11/12) (CLK-/+), (13/14)
+), (5/6) (D1-/+), (7/8) (D2-/+), all of IC1605? (D0-/+), (15/16) (D1-/+), (17/18) (D2-/+), all of IC1605?
NO NO
Is IC1605 (pin33/pin34) accessed by I2C, with HDMI Is IC1605 (pin39/pin40) accessed by I2C, with HDMI
connected, to read the DDC_I2C SDA/SCL data? connected, to read the DDC_I2C SDA/SCL data?
NO NO
Check the DDC line and its peripheral circuits. Check the DDC line and its peripheral circuits.
(IC1605 and its peripherals). (IC1605 and its peripherals).
YES YES
Are there the TMDS signal inputs at pins (AJ6/AK6) (CLK-/+), (AJ7/AK7) (D0-/+), (AJ8/ NO Check IC1605, IC8001 and their peripheral
AK8) (D1-/+), (AJ9/AK9) (D2-/+), all of IC8001 (CPU)? circuits.
YES
Are the LVDS signal outputs at the LVDS 1st channel and 2nd channel of IC8001? NO Check IC8001 and its peripheral circuits.
LVDS_TX_0_DATA0_P/N (C14/D14), LVDS_TX_0_DATA1_P/N (C15/D15), (IC8152/IC8153, etc.)
LVDS_TX_0_DATA2_P/N (C16/D16), LVDS_TX_0_DATA3_P/N (C18/D18),
LVDS_TX_0_DATA4_P/N (C19/D19), LVDS_TX_0_CLK_P/N (C17/D17),
LVDS_TX_1_DATA0_P/N (A14/B14), LVDS_TX_1_DATA1_P/N (A15/B15),
LVDS_TX_1_DATA2_P/N (A16/B16), LVDS_TX_1_DATA3_P/N (A18/B18),
LVDS_TX_1_DATA4_P/N (A19/B19), LVDS_TX_1_CLK_P/N (A17/B17).
YES
Check the panel module.
6–6
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
HDMI: No external input video [INPUT-6] HDMI: No external input video [INPUT-8]
Is INPUT-6 selected on the input select menu screen? Is INPUT-8 selected on the input select menu screen?
NO NO
Select INPUT-6 on the input select menu screen for the Select INPUT-8 on the input select menu screen for the
right input signal. right input signal.
YES YES
Does the HOT PLUG detection function? Does the HOT PLUG detection function?
Does the DDC5V signal come from pin (18) of SC1801 to pin (32) of Does the DDC5V signal come from pin (18) of SC1802 to pin (42) of
IC1801 (HDMI_SW2)? IC1801 (HDMI_SW2)?
NO NO
Check the line between the input terminals of SC1801 Check the line between the input terminals of SC1802
and IC1801. and IC1801.
Check IC1801 and its peripheral circuits Check IC1801 and its peripheral circuits
(SDA1: pin53 of IC1801/SCL1: pin54 of IC1801, etc.). (SDA1: pin53 of IC1801/SCL1: pin54 of IC1801, etc.).
YES YES
Does the HPD signal come from pin (31) of IC1801 to pin (19) of Does the HPD signal come from pin (41) of IC1801 to pin (19) of
SC1801? SC1802?
NO NO
Check the line between the pin (31) of IC1801 and the Check the line between the pin (41) of IC1801 and the
pin (19) of SC1801. pin (19) of SC1802.
Check IC1801 and its peripheral circuits Check IC1801 and its peripheral circuits
(SDA1: pin53 of IC1801/SCL1: pin54 of IC1801, etc.). (SDA1: pin53 of IC1801/SCL1: pin54 of IC1801, etc.).
YES YES
Are there the TMDS signal inputs at pins (65/66) (CLK-/+), (67/68) Are there the TMDS signal inputs at pins (11/12) (CLK-/+), (13/14)
(D0-/+), (69/70) (D1-/+), (71/72) (D2-/+), all of IC1801? (D0-/+), (15/16) (D1-/+), (17/18) (D2-/+), all of IC1801?
NO NO
Is IC1801 (pin29/pin30) accessed by I2C, with HDMI Is IC1801 (pin39/pin40) accessed by I2C, with HDMI
connected, to read the DDC_I2C SDA/SCL data? connected, to read the DDC_I2C SDA/SCL data?
NO NO
Check the DDC line and its peripheral circuits. Check the DDC line and its peripheral circuits.
(IC1801 and its peripherals). (IC1801 and its peripherals)
YES YES
Are there the TMDS signal inputs at pins (19/20) (CLK-/+), (21/22) (D0-/+), (23/24) (D1-/
+), (25/26) (D2-/+), all of IC1605 (HDMI_SW1)?
NO
Check IC1801, IC1605 and their peripheral circuits.
YES YES
Are the LVDS signal outputs at the LVDS 1st channel and 2nd channel of IC8001? NO Check IC8001 and its peripheral circuits.
LVDS_TX_0_DATA0_P/N (C14/D14), LVDS_TX_0_DATA1_P/N (C15/D15), (IC8152/IC8153, etc.)
LVDS_TX_0_DATA2_P/N (C16/D16), LVDS_TX_0_DATA3_P/N (C18/D18),
LVDS_TX_0_DATA4_P/N (C19/D19), LVDS_TX_0_CLK_P/N (C17/D17),
LVDS_TX_1_DATA0_P/N (A14/B14), LVDS_TX_1_DATA1_P/N (A15/B15),
LVDS_TX_1_DATA2_P/N (A16/B16), LVDS_TX_1_DATA3_P/N (A18/B18),
LVDS_TX_1_DATA4_P/N (A19/B19), LVDS_TX_1_CLK_P/N (A17/B17).
YES
Check the panel module.
6–7
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
NO
Select INPUT-9 on the input select menu screen for the
right input signal.
YES
Does the HOT PLUG detection function?
Does the DDC5V signal come from pin(18) of SC1803 to pin(46) of
IC1801(HDMI_SW2)?
NO
Check the line between the input terminals of SC1803 and
IC1801.
Check IC1801 and its peripheral circuits
(SDA1:pin53 of IC1801/SCL1:pin54 of IC1801, etc.).
YES
Does the HPD signal come from pin(45) of IC1801 to pin(19) of SC1801?
NO
Check the line between the pin(45) of IC1801 and the
pin(19) of SC1801.
Check IC1801 and its peripheral circuits
(SDA1:pin53 of IC1801/SCL1:pin54 of IC1801, etc.).
YES
Are there the TMDS signal inputs at pins(19/20)(CLK-/+), (21/22)(D0-/+), (23/
24)(D1-/+), (25/26)(D2-/+), all of IC1801?
NO
Is IC1801(pin43/pin44) accessed by I2C, with HDMI con-
nected, to read the DDC_I2C SCL/SDA data?
NO
Check the DDC line and its peripheral circuits.
(IC1801 and its peripherals).
YES
Are there the TMDS signal inputs at pins(19/20)(CLK-/+), (21/22)(D0-/+), NO Check IC1801, IC1605 and their peripheral circuits.
(23/24)(D1-/+), (25/26)(D2-/+), all of IC1605(HDMI_SW1)?
YES
Are the LVDS signal outputs at the LVDS 1st channel and 2nd channel of IC8001? NO Check IC8001 and its peripheral circuits.
LVDS_TX_0_DATA0_P/N (C14/D14), LVDS_TX_0_DATA1_P/N (C15/D15), (IC8152/IC8153, etc.)
LVDS_TX_0_DATA2_P/N (C16/D16), LVDS_TX_0_DATA3_P/N (C18/D18),
LVDS_TX_0_DATA4_P/N (C19/D19), LVDS_TX_0_CLK_P/N (C17/D17),
LVDS_TX_1_DATA0_P/N (A14/B14), LVDS_TX_1_DATA1_P/N (A15/B15),
LVDS_TX_1_DATA2_P/N (A16/B16), LVDS_TX_1_DATA3_P/N (A18/B18),
LVDS_TX_1_DATA4_P/N (A19/B19), LVDS_TX_1_CLK_P/N (A17/B17).
YES
Check the panel module.
6–8
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
No audio (1)-1
Is INPUT-1 selected on the input select menu screen? Is INPUT-2 selected on the input select menu screen?
NO NO
Refer to “: No external input video [INPUT-1]”. Refer to “: No external input video [INPUT-2]”.
YES YES
Is the audio output selected for “VARIABLE” on the menu screen? Is the audio output selected for “VARIABLE” on the menu screen?
NO NO
Set the audio output to “FIXED”. Set the audio output to “FIXED”.
YES YES
Does the audio signal come from pins (5) (L) and (7) (R) of input Does the audio signal come from pins (4) (L) and (2) (R) of input
terminal (J507) to pins (V30)(L) and (V29) (R) of IC8001 (CPU)? terminal (J503) to pins (U29) (L) and (U28) (R) of IC8001 (CPU)?
NO NO
Check the line between J507 and IC8001. Check the line between J503 and IC8001.
YES YES
Does the audio signal come from pins (N29/N30) (PGA0OUT_L/R) of IC8001 (CPU) to pins (4/7)
(INLP/INRP) of IC2701 (AMP)?
NO
Check the line between IC8001 and IC2701,
and their peripheral circuits (Q1306/Q1307,
AMP_MUTE line, etc.).
YES
Is the audio output from IC2701 as specified? NO Check IC2701 and its peripheral circuits.
YES
Check the connector (P2701), speakers and their peripheral cir-
cuits.
6–9
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
No audio (1)-2
INPUT-3 No audio.
NO
Refer to “: No external input video [INPUT-3]”.
YES
Is the audio output selected for “VARIABLE” on the menu screen?
NO
Set the audio output to “FIXED”.
YES
Does the audio signal come from pins (5) (L) and (4) (R) of input ter-
minal (J501) to pins (U27) (L) and (U26) (R) of IC8001 (CPU)?
NO
Check the line between J501 and IC8001.
YES
Does the audio signal come from pins (N29/N30) (PGA0OUT_L/R)
of IC8001 (CPU) to pins (4/7) (INLP/INRP) of IC2701 (AMP)?
NO
Check the line between IC8001 and IC2701,
and their peripheral circuits (Q1306/Q1307,
AMP_MUTE line, etc.).
YES
Is the audio output from IC2701 as specified? NO Check IC2701 and its peripheral circuits.
YES
Check the connector (P2701), speakers and their peripheral circuits.
6 – 10
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
No audio (2)
[PC analog audio input] INPUT-4 No audio. [HDMI analog audio input] INPUT-6 No audio.
Is INPUT-4 selected on the input select menu screen? Is INPUT-6 selected on the input select menu screen?
NO NO
Refer to “: No external input video [INPUT-4]”. Refer to “: No external input video [INPUT-6]”.
YES YES
Is the audio output selected for “VARIABLE” on the menu screen? Is the audio output selected for “VARIABLE” on the menu screen?
NO NO
Set the audio output to “FIXED”. Set the audio output to “FIXED”.
YES YES
Is the “PC Audio Select” selected for “Input4 (PC)” on the menu Is the “PC Audio Select” selected for “Input6 (HDMI)” on the menu
screen? screen?
NO NO
Set the HDMI audio output to “Input4 (PC)”. Set the HDMI audio output to “Input6 (HDMI)”.
YES
Is the HDMI audio output selected for “Digital” on the menu screen?
NO
Set the HDMI audio output to “Analog”.
YES
YES
Does the audio signal come from pins (2) (L) and (3) (R) of input terminal (J1801) to pins (V28)
(L) and (V27) (R) of IC8001 (CPU)?
YES NO
Does the audio signal come from pins (N29/N30) (PGA0OUT_L/R) Check the line between J1801 and IC8001.
of IC8001 (CPU) to pins (4/7) (INLP/INRP) of IC2701 (AMP)?
NO
Check the line between IC8001 and IC2701,
and their peripheral circuits (Q1306/Q1307,
AMP_MUTE line, etc.).
YES
Is the audio output from IC2701 as specified? NO Check IC2701 and its peripheral circuits.
YES
Check the connector (P2701), speakers and their peripheral cir-
cuits.
6 – 11
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
No audio (3)
No audio at UHF/VHF broadcast signal reception. No audio at digital broadcast signal reception.
Is TV selected on the input select menu screen? Is TV selected on the input select menu screen?
NO NO
Refer to “No video at UHF/VHF broadcast signal Refer to “No video at digital broadcast signal
reception”. reception”.
YES YES
Is the audio output selected for “VARIABLE” on the menu screen? If no video appears, refer to “No video at digital broadcast signal
reception”.
NO
Set the audio output to “FIXED”. Is the audio output selected for “VARIABLE” on the menu screen?
NO
Set the audio output to “FIXED”.
YES
Is there the SIF signal output at pin (16) of tuner (TU1101)?
NO
Check the tuner (TU1101) and its peripheral cir-
cuits.
(I2C line: TUN_SCL/TUN_SDA, etc.)
YES
Does the SIF signal come from pin (16) of tuner (TU1101) to pin (D5)
of IC8001 (CPU)?
NO
Check the line between TU1101 and IC8001, and
their peripheral circuits (Q1101, Q1102, etc.).
YES YES
Does the audio signal come from pins (N29/N30) (PGA0OUT_L/R) of IC8001 (CPU) to pins (4/7) (INLP/INRP) of IC2701 (AMP)?
NO
Check the line between IC8001 and IC2701, and their peripheral
circuits (Q1306/Q1307, AMP_MUTE line, etc.).
YES
Is the audio output from IC2701 as specified? NO Check IC2701 and its peripheral circuits.
YES
Check the connector (P2701), speakers and their peripheral circuits.
6 – 12
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
No audio (4)
[INPUT-5 input]
Is INPUT-5 selected on the input select menu screen?
[INPUT-6 input]
Is INPUT-6 selected on the input select menu screen?
[INPUT-7 input]
Is INPUT-7 selected on the input select menu screen?
[INPUT-8 input]
Is INPUT-8 selected on the input select menu screen?
[INPUT-9 input]
Is INPUT-9 selected on the input select menu screen?
NO
Refer to “: No external input video [INPUT-5/6/7/8/9]”.
YES
[INPUT-5 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-5]”.
[INPUT-6 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-6]”.
[INPUT-7 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-7]”.
[INPUT-8 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-8]”.
[INPUT-9 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-9]”.
NO
Set the audio output to “FIXED”.
YES
Does the audio signal come from pins (N29/N30) (PGA0OUT_L/R) of IC8001 (CPU) to pins (3/7)(INLP/INRP) of IC2701 (AMP)?
NO
Check the line between IC8001 and IC2701, and their peripheral circuits (Q1306/
Q1307, AMP_MUTE line, etc.).
YES
Is the audio output from IC2701 as specified?
NO
Check IC2701 and its peripheral circuits.
YES
Check the connector (P2701), speakers and their peripheral circuits.
6 – 13
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
If no video appears, refer to “No external input video (HDMI) If no video appears, refer to “No video at digital broadcast signal
[INPUT-5/6/7/8/9]”. reception”.
Is there the SPDIF signal output (OPT_OUT) at pin (J28) of IC8001 (CPU)?
NO
Check the IC8001 and its peripheral circuits.
YES
Is there the SPDIF signal (OPT_OUT) input at pin (2) of IC1303 (SPDIF SELECTOR)?
NO
Check the line between IC8001 and IC1303.
YES
Is there the SELECT signal input at pin (6) of IC1303? (High)
NO
Check IC1301, and it peripheral circuits.
YES
Is there the MUTE signal input at pin (7) of IC1303? (usual: Low, Mute: High)
NO
Check the MUTE_A_ALL and AC_DET signals, and their peripheral circuits
(Q1304, D1301, D1310, etc.).
YES
Is there the SPDIF signal input at pin (1) of D1306 (OPTICAL OUTPUT)?
YES NO
Check the speakers and the optical cable. Check D1306 and its peripheral circuits.
No optical output under the following conditions as per HDMI requirements.
* Audio contents protected.
* Audio frequency beyond 48kHz.
* Audio bit length beyond 16bits.
6 – 14
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
Is the audio output from the monitor set at “VARIABLE” or “FIXED” on the menu screen?
NO
Check IC8001 (CPU) and its peripheral circuits.
YES
Are there the audio signal outputs at pins (N27) (PGA1OUT_L) and (N28) (PGA1OUT_R) of IC8001 (CPU)?
NO
Check IC8001 (CPU) and its peripheral circuits.
YES
Does the audio signal come from pins (N27) (PGA1OUT_L) and (N28) (PGA1OUT_R) of IC8001 to pins (4) (L) and (2) (R) of J505?
NO
Check the line between IC8001 and J505 and their peripheral circuits.
Check the LINE_MUTE line and its peripheral circuits (Q1310/Q1311, etc.).
YES
Check the connector (J505) and their peripheral circuits, and speakers and the Cable.
6 – 15
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
250ms 1sec
L: Off
Communication error H: On Refer to “Communication error details”.
with the main CPU Communication line error or main CPU communication error →
Flashes 3 times Check debug statements for the main CPU.
L: Off Communication line with the main CPU: TxD(28pin), RxD(29pin)
Vsync error H: On VSYNC (52pin) error (L or H fixed). Image processing IC opera-
Flashes 4 times tion error.
Detection is performed during operation (interrupt).
L: Off
Monitor temperature H: On If the panel temperature is 60°C or more for 15 seconds or more in
error a row, CAUTION appears on the OSD (“TEMPERATURE” flashes
Flashes 5 times in red in the lower right portion of the screen).
L: Off If the panel temperature is 60°C or more for 25 seconds or more in
a row, error standby is activated.
[Avoidance method] Reduce the value of MONITOR MAX TEMP
(temperature protection threshold) on page 28 of the process A.
BD unit error H: On BD unit error
Flashes 6 times For the error details, refer to “standby cause” in the process menu.
L: Off
Program area data H: On Flash ROM data error in the microprocessor
destruction [Recovery method] Write the microprocessor software.
Flashes 8 times
L: Off
6 – 16
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
2) Power error details (Power LED flashes twice and OPC LED flashes)
Pins are monitor microprocessor pins unless otherwise
Error type OPC LED operation (1 cycle)
specified.
DET_10V error H: On DET_10V (57pin). UR10V or A9V is not applied.
Flashes once If error is detected during operation, error standby is activated by
polling.
L: Off
DET_D3V3 error H: On DET_D3V3 (59pin) error (L). D3.3V is not applied.
Flashes twice If error is detected during operation, error standby is activated by
polling.
L: Off
DET_6V error H: On DET_6V (56pin) error (L). D5V or A5V is not applied.
Flashes 3 times If error is detected during operation, error standby is activated by
polling.
L: Off
PNL_12V error H: On DET_PNL_12V (58pin) error (L). Panel power is not applied.
Flashes 5 times If error is detected during operation, error standby is activated by
polling.
L: Off
Main error H: On Main microprocessor detection error (FAN error, 1bitAMP error,
Flashes 7 times etc.)
Details are displayed in “ERROR STANDBY CAUSE” on page 1 of
L: Off the process A for the main microprocessor.
TCON ROM error H: On LCD controller ROM error
Flashes 8 times It is notified by communication from the main CPU.
L: Off
3) Communication error details (Power LED flashes 3 times and OPC LED flashes)
Basically, log analysis of debug print statements or com-
Error type OPC LED operation (1 cycle)
munication log analysis by a bus monitor is performed.
Initial communication reception error H: On Initial communication from the main CPU is not received.
Flashes once (Request for the monitor model No. is not received after cancel-
ing the reset.)
→ Communication line error or main CPU start-up failure.
L: Off
Time-out setting reception error H: On Time-out setting and start-up mode change from the main CPU
Start-up confirmation reception error is not received. (Start-up communication of time-out setting and
Flashes twice start-up mode change is not received.)
→ Main CPU start-up failure or monitor microprocessor recep-
L: Off
tion failure.
Regular communication error H: On Regular communication that is performed at 1 second intervals
Flashes 3 times in the normal operation is interrupted.
→ Main CPU operation failure or monitor microprocessor recep-
tion failure.
L: Off
MONITOR_ERR_CAUSE list
No. Description
Dec. Hex.
0 0 No error
1 1 6V detection error
2 2 Panel 5V detection error
3 3 10V detection error
4 4 D3.3V detection error
5 5 VSYNC error
6 6 Lamp error
8 8 Main CPU reset cancel - Start-up completion command reception time-out
9 9 Start-up completion command reception - Time-out setting command reception time-out
10 A Time-out setting command reception - Start-up reason change command reception time-out
11 B Regular communication time-out
12 C Temperature protection
16 10 Error notification from the main CPU
17 11 Time-out during ending sequence
18 12 TCON ROM error
19 13 BD unit error
6 – 17
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
LC46E77U
CHAPTER 7. OVERALL WIRING/SYSTEM BLOCK DIAGRAM Service Manual
㪿㪼㪸㫋㫊㫀㫅㫂㩷㫄㫌㫊㫋㩷㪹㪼㩷㪸㫋㫋㪸㪺㪿㪼㪻㩷㫆㫅㩷㫋㪿㪼㩷㪺㫆㫄㫇㫆㫅㪼㫅㫋㩷㫎㫀㫋㪿㩷㫋㪿㫀㫊㩷㫄㪸㫉㫂
䋼㪠㪥㪭㩷㪬㫅㫀㫋䋾 㪉
㪋㪍㩹㪻㫀㪾㫀㫋㪸㫃㪄㫊㫋㪸㫅㪻㪸㫉㪻䋺㪩㪬㪥㪫㪢㪘㪌㪊㪏㪆㪘㪌㪊㪐㪮㪡㪥㪈 㪈
㪌㪉㩹㪻㫀㪾㫀㫋㪸㫃㪄㫊㫋㪸㫅㪻㪸㫉㪻䋺㪩㪬㪥㪫㪢㪘㪌㪉㪏㪆㪘㪌㪉㪐㪮㪡㪥㪈
䋼㪠㪥㪭㪄㪞㪥㪛㩷㪬㫅㫀㫋䋾
㪋㪍㩹㪻㫀㪾㫀㫋㪸㫃㪄㫊㫋㪸㫅㪻㪸㫉㪻䋺㪩㪬㪥㪫㪢㪘㪌㪋㪇㪆㪘㪌㪋㪈㪮㪡㪱㪱 㪠㪥㪭㪈㩷㪬㫅㫀㫋
㪉
㵘㪌㪉㩹㪻㫀㪾㫀㫋㪸㫃㪄㫊㫋㪸㫅㪻㪸㫉㪻䋺㪩㪬㪥㪫㪢㪘㪌㪊㪇㪆㪘㪌㪊㪈㪮㪡㪱㪱 㪈
㪉
㪈
㪉
㪈
㪈 㵘㪌 䇼㪧㪙䇽
㪈
㪈 䇼㪣㪙㪈䇽 䇼㪣㪙㪉䇽 㪈
㪉
㪍 㪍 䇼㪣㪙㪉䇽 㪈
㪐
㪈 㪈
㪈 䇼㪣㪘䇽 䇼㪣㪘䇽
䇼㪧㪛䇽 㪊 㪊
㪉
㪠㪥㪭㩷㪞㪥㪛㪈㩷㪬㫅㫀㫋 㪈㪉 㪏 㪈
㪈
㪘㪌㪈㪎
㪈 䇼㪧㪣㪪䇽
㪋 㪏 㪈 㪉
㪠㪥㪭㩷㪞㪥㪛㪉㩷㪬㫅㫀㫋 㪈
㪘㪌㪈㪏
䇼㪣㪙㪈䇽 㪈
㪍 䇼㪧㪛䇽 㪠㪥㪭㪉㩷㪬㫅㫀㫋
㪧㪦㪮㪜㪩㵘㪬㫅㫀㫋
㪈
㪤㪘㪠㪥㩷㪬㫅㫀㫋 㪛㪛㪩 㪋㪍㩹㪃㪌㪉㩹䋺㪩㪛㪜㪥㪚㪘㪊㪊㪍㪮㪡㪨㪱 㪉
㪜㪏㪊㪊 䇼㪣㪧䇽 㪈 㪈
㪧㫆㫊㫀㫋㫀㫆㫅
㪈㪉
㪈
㪤㪛㪢 㪉
䇼㪢㪤䇽 䇼㪢㪤䇽 㪈
㪈 㪈
㪈 㪋
㪌 䇼㪣㪮䇽 㪋 㪣㪚㪛㩷㪚㫆㫅㫋㩷㪬㫅㫀㫋
㪢㪜㪰㩷㪬㫅㫀㫋 㪋㪍㩹䋺㪚㪧㪮㪙㪯㪋㪇㪉㪊㪫㪧㪯㪘 㪉
㪜㪉㪍㪍 㪌㪉㩹䋺㪚㪧㪮㪙㪯㪋㪇㪉㪊㪫㪧㪯㪱 㪈
䌈䌄䌍䌉
㪟㪛㪤㪠
㫆㫇㫋㫀㪺㪸㫃 㪫㪬㪥㪜㪩
㪧㪚㩷㪘㫌㪻㫀㫆㩷㪠㪥 㪣㪆㪩㩷㫆㫌㫋 㪉
㪈
㪈㩷㩷㩷㩷㪈㪌 㪈㩷㩷㩷㩷㩷㩷㪋㪈 㪈 㪋
㪭㪆㪣㪩
㪪
䇼㪣㪧䇽 䇼㪣㪮䇽 䇼㪧㪣㪪䇽
㪰㪼㫃㫃㫆
㫎 㪉
㪬㪪㪙
㪈㩷㩷㩷㩷㩷㩷㩷㩷㪏㪇 㪈㩷㩷㩷㩷㩷㩷㩷㩷㪏㪇 㪈
䇼㪩㪘䇽 䇼㪪㪧䇽
㪩㪪㪄㪉㪊㪉㪚
㪘㫅㪸㫃㫆㪾㩷㪩㪞㪙 㪈㩷㩷㩷㩷㩷㩷㩷㪈㪇 㪈 㪋
䇼㪩㪘䇽 㪈㩷㩷㩷㩷㩷㩷㪈㪇
㪝㫌㫃㫃㪄㪟㪛㩷㪧㪸㫅㪼㫃㩷䋨㪈㪐㪉㪇㬍㪈㪇㪏㪇䋩
㪣㪜㪛㩷㪬㫅㫀㫋 㪪㪟㪘㪩㪧㩷㫇㫉㫆㪻㫌㪺㫋
㪝㪇㪐㪍 㪌㪉㩹䌾㪋㪍㩹㩷㪻㫀㪾㫀㫋㪸㫃㪄㫊㫋㪸㫅㪻㪸㫉㪻㩷㫄㫆㪻㫌㫃㪼䋺㪩㪈㪣㪢㩿㪌㪉㪆㪋㪍㪀㪇㪛㪊㪣㪮㪏㪇㪱
㪩㪺㪿㪑㩷㪩
㪩㪪㪧㪄㪱㪘㪋㪈㪋㪮㪡㪱㪱 㪣㪺㪿㪑㩷㪩
㪩㪪㪧㪄㪱㪘㪋㪈㪊㪮㪡㪱㪱
7–1
/#+0
%8$5
+0276 .4
.4
%QORQPGPV ;2D2T
5*+2A'020'.A'0
ޣ.9ޤ2
R((%
58KFGQ 58KFGQ
+0276
.4 &'6'%6
.4
%QORQPGPV ;2D2T
$7
8
8 #/2A/76' +%
䇼㪪㪧䇽 㪠㪚㪉㪎㪇㪈 56#0&$; 4GUGV
52 㪧㪉㪎㪇㪈 㪪㪧㩷㪘㪤㪧 2416'%6 456A(.5A%27
㪜㪯㪫㪄㪪㪧 㪰㪛㪘㪈㪋㪏㪨㪱
(TQO%27
2
&KUENGVG 45A$7(A%06 %QPPGEVQT
&'6A20.8
.4 /WVG HQT5QHVYCTG
#WFKQ1WV &KUENGVG
/WVG 9TKVG
'OWNCVQT
8DTV 41/5'.
2
$7
8 (4#/'4.7&6'/2=?15A5'6
8
8 4Z&6Z& +1
8 56$
.+0'A/76' +% +% +1 8QP
+% +% 56$A%27
+1 ''241/ &#% +% /%
(TQO%27
+1A52&+(A/76' .#8 *&%2 /(2 )CVG +:%9, 8DTV
9*(7 /QPKVQT/KEQO
67
8
4Z&6Z& 7#46 ''241/A5%.5&#
4(+0 #PCNQI +%
&KIKVCN #(6
%8$5 6*'4/1 $7
8
6WPGT 6JGTOKUVGT #& 92 +%
/*\ ''241/
+%
&A+(
5%5,
#)%
5+(
670'4A+%
-*\88 %08UU /*\ '44A20.
670'4A+%
8
651WV
%8$5
58KFGQ
;2D2T
.8&5176
:VCN
65+P
+%
-*\ 5%
+%A
-*\8 +%A
8 20.A&'6=? #%A&'6
%QPPGEVQT
+%A
8 HQT
8 2CPGN &GVGEV
#(6 +1
ޣ.$ޤ2
/1&'.A&'6=? +1
&A+(KP
8 5%
RKP
5+( %QPPGEVQT 2/A4'3%$1165 +1
#)% HQT 0A54'5'6 +1 +06 #& +1
/QFGN &GVGEV
4)$KP
*&/+KP 1(.1(.
+% 8%1/A92.%&A'0
ޣ.2ޤ2
6'56 /1&'
RKP
/6(
(WNN*& &'6%10&A&'6
$7
8
/*\
+:%9, 20.A+%A'0
㪠㪚㪐㪇㪇㪊 +%
㪩㪪㪉㪊㪉㪚㩷㪫㫏㪩㫏 6Z&4Z& : &KIKVCN#8FGEQFG/CKP%27 +%59 20.A8
45% 㪘㪛㪤㪊㪈㪇㪈㪜 : VCN
0QRKP4%2CUUVJTQWIJ
8 52176A.4
&'6A8&'6A
%27A52&+(A176 .+0'A.4 #WFKQQWV
126+%#. +%
176 &&4
8
8A.4
8A.4 /DKV
8A.4 #WFKQKP
+0276 4)$*&/+
12%A.'&219A.'&A4219A.'&A).'&A;1;#-7+..A.'&
0A%27A456 ˴$7
8
7#46
7#46
7#46
\\
75$A
#%A&'6
/CKP.KPG
25A10
4)$ ˴#8
ޣ2&ޤ219'4˴2
2+0
+%
8 #8
''241/ ˴8
+%
-*\ ˴&8
+0276 0A&$)A456
*&/+ ˴&8
-';-';56#0&$;219
5+&' ˴&8
+%
8
0A54'5'6 748
+%
8 &8
6/&559 ''241/ $78
+0276 *&/+ 5++ MDKV 20.A8
+P (TQO%27 20.A10
2QYGT%KTEWKV
+P $7
8
4%
12%
+0276
8
*&/+
+P 2 +%
+%
8 5QHVYCTG9TKVKPI 0#0&(.#5* ޣ-/ޤ2
R ޣ4#ޤ2
R
+P
6/&559 %QPPGEVQT /DKV ޣ-/ޤ2
R ޣ4#ޤ2
R
+0276 5++
*&/+
+P -'; 4%
.'& 12%
+P 㪧㪦㪮㪜㪩 .'&
+0276 *&/+ 㪤㪜㪥䌕
㪠㪥㪧㪬㪫
+P
+P 㪚㪿㪄㪬㫇㪆㪛㫆㫎㫅
㪭㫆㫃㪄㪬㫇㪆㪛㫆㫎㫅
5GTXKEG ,
75$
7–2
E
KEY Unit (Chip Side A)
D
R154 D155
R153
S153
S155
S151
S152
S156
S157
S154
D152
R151
D151
R152 P151
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8–1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8–2
J501
SC1601
J8001 LUG1101 S2002 S2003 S2005 S2006 S2004 S2001 S2007
D2001
C1849
D1812 R1901
R590
C2029
BAR3
R536 FB2003
LUG1102
FB511
FB512
R9201
C542
IC1809
R535
FB2001
FB2002
R1899 IC1601
FB2004
R549
C536
R540
FB8001 VA8001
C540
C535
LUG1106
FD2
VA8002
C8001
R1834
R1833
R1837
C1841
R1827
IC8002 D1813
C8002
D1810
FB1806
C8004
C1833
C1834
C1824
IC1803 IC1602
C1832
P2002
Q1807
C1818
R1882
C1840
KOUJO1
FB1805 FB1804
R1845
R1841
D1809
R2639
R1832
R1846 C1823
R1836
J1801
R2026
SC1804 Q1806
R1825
D1808 L1801
C1839
R1840
BAR1
R1844
R2027
R1842
C1805 C1806
FB1802 R2048
C1808
C9720
R2057
R1879 C2013
C1813
C1816 R1830
R1881 Q2004
R2037
C1814
R2044
FB1808
FB1807
R1835
R1817 C1810
R2059
R1818
R1880 P2001
R1814
C1807
D1806
Q2003
C1809
IC1605
R1819
FB2508
P9202 D2505
H R9001 D9002 R9023 L1803
C1803
R1839
TH2001
R1686
R9002
R9622
D1807 IC9001 L1804
R9623
R1821 D9007 L1602
R2019
R1872
C9601
R9022
C1812
C1801
IC1801
R2056
R1666
C1621
R1689
R1654
R1653
R1688
IC9606
C9632
C9628
R1866 R1823 L1604 R8039
R1658
R1657
C9009
R1651
C9602
R1867 R1849 R1131
D8001
C1622
R1919
R1130
R9020
IC2008
IC9003
D1306
L9604
D9001 R1604 R2016
C2026
R1652
SC9001 R1915
TP8046
R1884
C9006
TP8051
IC1804
R1691
TP8055
C1851
R9021
TP8053
SG2507
SG2508
D9005
R1916
R1857
R1858
R1860
IC1805
C9008 R1847
D9604
IC1810
TP8045
TP8047
TP8052
TP8054
C9631
SG2506
R558
R555
C558
R554
R552
C556
C557
C555
R1904
R1902 SG2504
R1914
SG2503
P2502
SG2502
R1303
R1304 SG2501
D520
R8158
FB2502
SC1802 SC1803
J504
TP8065 C8032
TP8066
R9006
C565
R9013
R572
R8004
J503 IC9004 R9005 FB2504
C8025
C8026
C8024
C8091
C8023
C8022
C8028
C8030
C8029
C8093
C8027
C8092
C8094
C8031
C8034
C8033
C8096
C8095
R8005
R544 C9010
R2510
R9025
R8154
R8153
R9026
R8003
R569 IC8153
C539
R639
C563
FB520
D532 C8018 C8173
C580 FB513 C579 FB515 C578 FB516 FB521
R602 R8018
R601 C8021 C8165
R574 R8020 C8019 R8178
C537
C8179
R8176
C566
F C8020 C8166
R545 D531 C8017 R8180
R638
R8172
R543
R8162 C8168
J502 R8166
C1128
L1105
R1107R1134
R8171
LUG1114
R1133 C8169
R1135 R8164
R8181
C1106 R1139 R8168 C8170
LUG1110
D529
C1103 R8169
R8013
R8182 R8183
C8012 C8013
R8161
X8001
R8011
IC8001
R8165
R510
C502
R512
C511
C533
C517
R8174
R541
D528
L506
R8012
R8184
R8170 C8162
C525 C523
R622 R621
R8159
RDA8001
R8167
C1119
R8152 C8163
R8177
FB522
R561
C516 C508 C515
R1128 R8151
R514 R546
R8163
LF3
C8164
L505
R9003
R542
R8175
D527
C8172
R620
R8157
R580
R548
L504
R8043
D526
C569
R8041
R538 R8040
J505
C576 C575
C522
J2901
J9501
R2910 IC8152
R8071
R8066
R8068
R8067
R8069
R8044
VER1
X2901
J506 R2906
FB523
J508 R2907
R2905
C9623
C9625
R581
IC2902
C2906
C8178
R582 C2903
R2914
C570
C2905
R1332
R1347
R1320
R1310 R1334
C1305
R1316
R9522
D C9504 R2913
R1340 R1342
Q1303
FB524
R1312
C567
C1306 R9521
Q1311
R1313
X8601
C8601
R585
R2012
C1302
R8615
R8620
R9511
R9515
C1304
R9027
R9516
R2909
R9028
Q1302 R2912
L9501 D9501
R2904
R1319
R1346
C2609 D2907
R2017
R1335 R9517
R9608
D9607
FB2007 R9503
R8059
R8060
R2075 Q1309
R1338
FB2009 R9501
L9602
C1314
R8623
IC8601
R8058
R8057
Q9602
C9501
FB2010 R9508
R1326 C2602
R9510
FB2011
R8625
FB2013 L2704
R8456
R8457
FB2615
FB2601
R8050
FB2614
R8056
C8451
C8460 C8462C8461 C8453 C8452
C2731
L9701
C9708
FB2633 R8051 C9619
IC8454
IC8451
C2742 TU1101
C2743
P2701
IC2701
FB2637
FB2636
FB2635
FB2634
C2744
FB2638
SC9302
C2726
C2745
C2711
R2602
B
FB2611
SC9301
FB9713
FB2706
C2717
Q9704
R9308 R9742
C2730
FD1
L2612
L2610
L2609
L2611
L2602
FB2623
FB2621
FB2631
FB2629
FB2627
FB2625
LUG1105
L2601
L2606
L2605
L2604
L2603
L2608
L2607
LUG1103 L2701
C2725
IC1102
C1121
P9701
R1137
R1136
C1123
C1116
LUG1104
R1101
C1134
C1126
C1133
C1132
R1117
FB1101 C1135 Q1104 C1125
A FB1102
R1106
C1110
R1105
C1124
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8–3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8–4
C
D
H
A
B
G
1
2
3
R2506
FB2505
R2505
D2503
D2502
TL2501 FB2501
TL2505 TL2503
R9629 C9608 TL2506
R2504
C9612
LUG1108 TL2507 TL2502 IC2501
R2501
D2506
D2504
TL2504
R2503
R2507
C9618 IC9603 C2501
R2509 FD3
C9614
D2501 R2508
C2502
R2512
TL9701 C9609
R9609 C9615
TL2043
R2511
FB2507
R9633
R2502
FB2506
R2640 R2621 Q2502
TL9711 R9706 C9624 Q2501 Q2006
FB9701
R9634
R2003
C9635
D2508
C9710
D2507
D2601 TL9605 D2002
R2513
TL9710 FB9712 C9629
4
R2605
D9606
FB2619
FB2620
R9615
IC9602
Q2001
TL2610 R2514
R9614
R9616
C9713
R2515
R9617
TL2006
IC970 3
R9610
C8607
4
2
TL9715 FB9710 TL9722 TL2015
FB2618
R8611
FB2613 TL2621 TL2007
C8608
R8616
TL2672 TL2601 R2072 TL2008 R2020
C960 R9625
C9607 R961 R9611
D9703
C8097
TL9702 FB9709 TL2605 TP8603 TP8601 R2007
C2002
TL2009
R2623
TL2609 R8608 TP8605
D9601 C8151 R2068 TL2010 TL2033
TL9716 FB9711 FB2609 FB2603 R8610
TP8607 TP8604 TL9234
R8612
LF5
R2014
R8155
TL2011 IC2001
C2606
D9713 R8609 TP8606 TP8602TP8622 C8152
R2030 TL2012
C8609
R8614
R8613
TL9733 FB9708 TL2671
R8062
TL2670 TL9611 TL2030
C8184
C8175
C8185
R9736
R8607
R8619 TL2014 R2025
R8061
C2003
C9709
TL9717 FB9707
R8618
FB2610 TP8626 TL2001 TL9235
Q9701
TL2650
D9609
TL9275
D9602
R8617 C8182 TL2013
FB2617
IC8151
C8191
FB9706 TL2027
C8157
R8156
TL9708
R9739
C8159
R8604 R8603 TP8625 C8187 TL8151 R2062 TL2031
C8156
FB2616 D9603 C8181 C8186 R2063
TL9724 FB9705
C8188
R9206
R8602 R8606
C8158
TL2649 TL2032
Q9702
R9705 D9701
FB2612
C8177
R8601 R8605TP8611
R2079
TL2614 TP8609 C8153
TL9705 FB9704
C8180
R2604
TP8613 TP8610 C8605 C8154 TL9236
5
TL2673 TL9610 TP8608 C8189
R9704
C8610 C8155
C8606
TL9704 FB9703 TP8614 TP8612
R9738
C8174
C8190
C8176
TL9220 TL9201
D9702
TL8456 TL2035
C8183
C9626
C8611
C9711 R9740
TL9703 FB9702 TL9206 TL9241
TL9601 TL9221
TL9240
R9741
TL9720 C9719 TL9723 FB2602 TL2648 TL2669 TL9205
TL2638 R9204 TL9239
R2081
TL9237
IC9604
R9618
R9613
TL9204 R9207TL9224
R9209
TL2606 TL2604
Q9603
R9202 R9208 TL9223
C9701
TL2608 TL9203 TL9222
R9601
IC9701
TL2607 C9603
R9701
R9212
TL9208
R9211
D2004
R9605
TL2611
R9603
C9636
R9602 C9606
R9203
R2082
TL2612 R9604 TL9238
R9702
C9605
TL9207
TL9202
TL2613 LUG1107 TL2044
R9631
TL9603
R8453
C8455
R8455
C9617
C8039
R8185 R8186
Q9601
TL9606
IC9605
IC9601
R8451 C8098
6
R9607
R9630 C9630 C8084
C8083
TP9501 TP8060
R9621 TL9604 C8043
C9610 C9611 TP8063 C8045 C8040
TP8061 R8063
C8085
TL9309 C9613 TP8025
TP8026 C8044 C8041 C8059
R9620
TP8064 C8042 TP8028
TP8027 TP8030
R8006
TL9303
C8087
C8086
TL9301 TL9302 TP8062
C8079C8102 TP8058
D9304 TP8029
D9605
TL9314 TL9304 C8089 C8081 TP8068
R9305
TL9312
C8072
R9325 C8080 C8082 C8067 C8075 TL9219
TL9313 TL9305 C9303 C8078 C8068
TL9311 C8100 TP8040 TP8041
R9302
R9326
IC8453
D9302 D9301 C8070
R8078
TL9315 Q8001
TL9306 R2620 R9301 C8077 C8071TP8032 R2039 TP2015
TL9307 C9302
C8099
TL9308 C8053 TP8037 R8064 R2040 TP2001
R2038
TP8031 R8007 R8030
R9319
TL9316 R2619 C2024
D9303
R8048
IC9301
C8062
C8065 TL2042
R2046
C9301 TP2003
7
R8464 C8069 C8101 C8063 R8027
C8014
R8014
IC2007
R8075
C2015
C9304
C8076
C8074
C8073
R2070
R2006
R2001
C2016R2049
R2047R2078
R2055C2008
R2032R2033
C8061 R8054 R2051
TP8033 C8054 X8002 C8058 R8029 TP2013
R8053 R8077 R2052
TP8034 R8008 R8079 C2014
R8463
R8461
R8462
R2004
R8015 R8028 R8076 R2050
C8010
C8006
C8046
C8015
C8456 C8088 R2071 TP2011
C8056
R2919
C8051
C8060
TL8010 R8024R8072
R8459 R8458 C8052 R2024
C8057
C8090
R2920 C8055 C8005 TP8036
C8009
R2023
C8064
R2921 R8025
R8065
TP8035 TL9212
TL9213
R8009 C8066
C8008 C8007
R8073 TP2002
TP2006 TL2034
R8047
R8010 R8046
TP8067
TL8454 TP8048 R8026R8074 R2005 TP2004
TP2005
IC2002
C8011
TP8038TP8042 R2013 R2011
TP8039 TL9210
TL9211
R8036
R8034
R8031
R8037
C8035
C8036
TL8453 TL9209
R2015
IC2004
8
TL2623 TL8455 TL8011 TL8013
TL8012
C8038 C8037
C2012
C2017
R2060
R8035
R8033
R8032
R8038
R2061
C2018
TL2624 FB2604 R2031
R8017
R8022
R8021
R8023
R8019
R2042
TL2916
R2066
C2020
TP2010 TL2002 TP2023
TP2020
TP2018
TL2625 FB2605 R2043 R2002 TL2003
R2034
R2036
C2010
R2028
R2018
R2029
R2058
C2011 C2009 TP2602
X2002 R2077 TL2004
R2064
TL2626 FB2606 TL2029
R2045 R2053
R2616 X2001 TL2005 C2027
C2028
R2080
R2622 R2008
R2009
R2615 C2004C2005
TL2627 FB2607
R2010R2022
LUG1109
R9004
R9012
FB2632
R2635
R1611
R1606
Q2603
TL2639 TL2628 D1601 C1623 R1663
9
R8052 C1602
TL2913 IC2901 TL2907
R1601
TL2640
TL2641 R2636 R2908 IC1607
C2902
IC1603
TL2603 R2911
TL2642 R2601
R1602 D1606
TL2906 TL2917 R1610
IC1606 R1665
TL2643 D2906TL2901
TL2644
C1624
R2903
R2902
R2901
TL2645 TL2912
TL2646
C2907
TL2602 R2918 TL2905 R1669
IC2903
FB2901
FB2902
FB2903
FB2904
C1634
D1611
TL2647 TL2904
R2917
R1646
C1617
C1619
R1690
R2603 R2916 TL2903 TL2908
R2915 TL2909
TL2910
TL2911
TL2651 R1660 C1625
TL2918 R1605
R1648R1661 C1601
D2901
D2905
D2902
D2903
TL2914 TL2902 R1668C1627 C1613
R1638
D1613
R1642
R1641
Q1610
FB1605
R1640
C1628
R1667
C1615
C1614
Q1609
R1672
R1639
C9511
10
R1671 R1655
R1329
R1656
R1317 R1321 C9510 R1644
R1645
R9509
C9509 FB9502
Q1306
R1318 R1325 R9505
C1616
R1680
FB9503
D1615
R1330 C9502
R1684
R9506
C2704
C2705
C2706
C2707
D1617
Q1616
C9512 R1670
Q1614
FB9501 C1620C1626
R1682
C1618 D1612
C9507
Q1307
C9508
8–5
R1615
D1310
C1303 R1308 R1681 D1602
D1307 D1302
D1314 D1313
C1448
C2748 R2717 R1341
C2713
Q1811 TL1621
R2753
R1322 TL1619
C2712
C1632
R2754
Q2704
R1891
Q1615
D1610
D1607
R1442
C1447 R1441
C1633
R1302
R1444 D1603
D1609
11
TL1804 TL1609 R1683
C1455
D1823
C2724 C1453
D1816
C2723
R1324
D1819
TL1817 D1616
R1618
R2726
R1674
C1847 C1836
R1620
R1301
D1312 R1894 TL1613
R2731
IC1609 TL1607
R1621
R1870
R1871
Q1308
R2730 R2744 R1887 R1678 TL1617 D1614
TL1802
R2742
R2741
C1830
C1829
IC1406
D1305
R1446
R1447
IC1301
TL1604
R1803
R1802
D1824
R1607
R1603
R1869 R1859
R1865
Q1305 C1837
R1868 TL1601
C1451
C1842
R1917
R1609
C1301 C1454
R1864 R1886
R1908 R1855
R1443
C1452
C1450 R1440
R1445
D1608
C1835 R1854
R1608
R1448 R1911
R1888
Q1816 C1630
D1828
R1811R1824
D1820
D1817
R1907
D1827
C1804
C1826
C1852
TL9501
TL1844
R1673
C1831 TL1605
IC1608
R1853
12
C1845
D1822
R1885
R1874
R1875
TL9503 C1848
TL1845 TL1620
R1890
D1814
R1920
Q1810
R1892
TL1806
R1921
TL1826
FB1812 Q1808
R1805
Q1817 R1909
R1905
D1825
R1910
TL547 TL1827
R1822 TL1803 R1807
TL1801
TL1115
R1893
Q1813
TL508
D1830 R1913 R1906
Q1814
TL510
TL1113 TL518
TL531
TL509
13
TL1818
TL1111 TL516
TL548 TL1819
TL1110
TL1820 TL517
TL1104
TL1122 TL1811
TL559 TL560 R1309
C1308
C9004
R1307
R1311
R1345 TL1303
R573R588
R589R592
TL520
14
R1127
R1124
R1121
R1120
L1301
R1344
R1339
C1312
TL1822
R1343
C1309
IC9002
Q1102
C1311
TL1119
R9008
C1112
TL1114 TL521
TL1121 R1118 R537
D523 TL505
C519
TL1116 TL544 TL546
L501
C504
C510
R617
R1114
Q1101
TL1120
R1113
TL1112 R1115
R1119 R529
TL1848
C1107
R1109
R1140 R1110 TL530
R522
TL539 TL9001
CF1101 TL522
TL506
D524
R559 TL540 TL537
TL507
C520 C521
15
L502 L503
C505 C506
C512 C514
R618 R619
R1103 TL515 TL502 TL524
C1136
R1132
TL538
D525
TL1109 R516
TL1107
TL1105 TL542
TL1824
TL514 TL501 TL523 TL541
TL1108
TL549 TL503 TL525 TL8001
TL1102 TL8009
TL1816
TL9009 TL8008
TL8007
TL9010 TL1815
TL1101 TL8006
TL8002
16
TL9004 TL1823 TL1814
TL8005
TL551 TL511 TL527 TL534 TL9006
TL1813 TL1812 TL8004
TL550 TL504 TL526 TL533 TL9007
C2741
C2740
C2738
C2737
FB2702
FB2703
FB2704
FB2705
TL9008 TL1810
TL8003
TL1821
TL2702 TL2703 TL2704
TL1808
FD4 TL552 TL512 TL528 TL535
TL2701 TL553 TL513 TL529 TL536
D2701
TL2025TL2023TL2021TL2019TL2017
BAR2
D2702
TL2028 BAR4
D2704
D2703
TL2016
17
TL2026TL2024TL2022TL2020TL2018
18
19
LC-46/52E77U
LC-46/52E77U
[3] LED Unit
E 3
R116 C102
R107
C104
Q104
Q105
R106
R105
Q102 R120
R113 R109 C101
R103 R115
Q103
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8–6
CAUTION:
This circuit diagram is original one, therefore there may be a slight
difference from yours.
SAFETY NOTES:
1) DISCONNECT THE AC PLUG FROM THE AC OUTLET
BEFORE REPLACING PARTS.
2) SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS
POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS
OPERATING.
9–1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
9–2
MAIN1 (TUNER)
*TU1101
AA033WJQZ
TO MAIN12(EXBUS)
CVBS3
VIDEO CVBS3_CM
19
R1130
R1124
F 0 0
AFT_CPU
TO MAIN8(UCOM)
R1103
0 TU_AFT
AFT_OUT
17
TO MAIN16(POWER2)
SIF
16
A8V
*C1124 *C1131
*C1125 R1113 R1118
68u L1106
4700P 1u 12K F 2.7K F
25V 10uH
15
3.8 10u
1000P R1115 16V
CZB 100
3.2 KZA510WJPZ
*R1136 R1121 TO MAIN9(CPU)
IF(-) 100
13
100 CZ 2.2
1.6 SIF
Q1101
KTC3875SG SIF_CM
IF(+)
12
*R1137
100 CZ R1125 R1128
4.7K 10K
NC
IF_AGC
10
TU_AS
D
C1116 C1119
0.01u 0.047u
SCL 25V 10V
9
R1102 *R1105
47 470
4
R1101
47 TUN_AD_CTL
5
2
8
SDA
GND
7
C *C1126
0.1u
0.39uH
*Q1104 *R1134
25V 33pF *C1129
HN7G04FUA *R1107
0 CY
*R1138 0.01u
0 CZ 0 CZ
IF_N
NC
5
RF-AGC 33pF
FB1102
A206WJ
33pF
4
MB
C1102 IF_P
140mAmax
10u *R1133 *R1139 *C1130
10V 0 CZ 0.01u
0 CZ *R1135
KZA616WJQZ 33pF
3
GND 0 CY TO MAIN13(CONN)
0.39uH
FB1101 TUN_SCL
A206WJ
B BB TUN_SDA
2
20mAmax *C1134
C1101
10u 68u
10V 10V TO MAIN16(POWER2)
KZA616WJQZ AAPE
A5V
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
9–3
MAIN2(A_TERM)
INPUT3 INPUT1 INPUT2
J501 J502 MAIN UNIT 2/16
J GA079WJ
J507
GA109WJ
J508
GA108WJ
GA108WJ J503 J504
FA039WJ DA035WJ J505 DUNTKE833WE03
R W FA039WJ
R W (PWBXE833WJ)
4 3
1 2 3 4
1 7 6 2 5 3 4 1 2 3 4 5 6 7 1 2 3 4
1 2 3 4 5 6 7 1 2 3 4 5 6 7
2 1
7 5 6
C577 C580
15P 15P
50V 50V
CCZ CCZ
C575 C578
15P 15P
A045WJ
R590 C576 C579
A045WJ
A204WJ
A045WJ
A204WJ
A204WJ
A045WJ
A045WJ
A045WJ
A204WJ
50V
A045WJ
A045WJ
R514 50V
FB523
FB512
FB521
FB520
FB517
FB511
FB502
FB505
FB518
FB506
FB522
FB507
R545
A204WJ
A204WJ
A204WJ
A204WJ
FB515
FB509
FB516
FB510
1K 1K
R579 R581
C565 220 220
R569 R574
R509 75 0.1u 75
R539 R535 R511 R552 R555
220 1/10W 25V Z 1/10W
220 220 220 220 220
H R515
R591 75
R512 R510 R554 R558
75 R540 R536
1/10W 100K 100K 100K 100K
1/10W 100K 100K
R580 R582
100K 100K
LINE_OUT_L
G
LINE_OUT_R
CVBS2_M
CVBS1_M
C1_PLG
C2_PLG
V3_PLG
V1_PLG
S1_PLG
C2_PR
C1_PR
C2_PB
C1_PB
C1_Y
C2_Y
S1_C
V1_R
V1_L
V3_L
S1_Y
V3_R
V2_L
V2_R
TO MAIN9(CPU)
V1_L
V1_L
C510
15P CH V1_R
V1_R
COMP1_Y
C1_Y PMT V2_L
V2_L
COMP1_Y_CM
L501
0.15uH
V2_R
V2_R
F C504
15P
C519
15P
R537
0
V3_L
V3_L
CH CH
V3_R
V3_R
CVBS1_M CVBS1_M
C512
15P CH TO MAIN16(POWER2)
C533 A5V
COMP1_PB
C1_PB 470P
PMT CH
L502 TO MAIN15(POWER1)
0.15uH
D3.3V
C505 C520
15P 15P
E CH CH
TO MAIN9(CPU)
COMP1_PBR_CM
CVBS2_M COMP1_PBR_CM
C514 CVBS2_M
15P CH COMP1_PB
COMP1_PB
COMP1_PR
C1_PR PMT COMP1_PR
COMP1_PR
L503 C536
0.15uH COMP1_Y_CM
470P COMP1_Y_CM
CH
COMP1_Y
COMP1_PBR_CM COMP1_Y
C506 C521
15P 15P R559 COMP2_PBR_CM
0 CZ COMP2_PBR_CM
CH CH
COMP2_PB
COMP2_PB
D COMP2_PR
COMP2_PR
R573
KTC3875SG COMP2_Y_CM
100K Q519 COMP2_Y_CM
D531 C566
S1_Y MAZ9120H 4.7u COMP2_Y
COMP2_Y
6.3V
C515 CKZ
47
15P CH 1 2 Y_SIG1
R601
COMP2_Y 1/16W
R588 C537
C2_Y PMT 100K R596
470P CVBS1_M
COMP2_Y_CM 470 CVBS1_M
L504 CH
1/10W
0.15uH 3
NC
C508 C523
R543 R544 R546
15P 15P 10K 10K 10K
CH CH CZ CZ CZ
R547
B
R549
10K 10K
CZ CZ
C517
15P CH
COMP2_PR
C1_PLG
C2_PR PMT C1_PLG
L506
V1_PLG
0.15uH V1_PLG
COMP2_PBR_CM
S1_PLG
C509 C525 S1_PLG
R561
15P 15P
0 CZ
CH CH
C2_PLG
C2_PLG
V3_PLG
GND_B V3_PLG
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
9–4
4
UR13V
L1301
10uH
3
CEM
A5V
2
1
3.3 0.0 *R1311
C1311
5 4 22 C1312
5
10u
0.1u Z
VCC Y 10V
TO MAIN15(POWER1) 25V
*C1310
KZA616WJQZ D1306
D3.3V GPFSV51M
0.1u
25V SPDIF BUFFER OPTICAL OUTPUT
I & SPDIF MUTE
B A GND
*IC1304
AHC1G08W
1 2 3
TO MAIN17(SP_IF) *R1333
22K 0.0 0.0 0.0
*Q1312
KRC404E
*R1305
0
0.0
TO MAIN9(CPU)
5.0
CPU_SPDIF_OUT
TO MAIN4(AMP)
0.0
H N_STANDBY
N_PROTECT
AMP_MUTE
R1335
5.6K
C1306
1u R1310 TO MAIN2(A_TERM)
16V 1K
R1337
10K LINE_OUT_L
IMH23T110
Q1311
R1345
R1328 15K
C1309 0.2
1 2 10u
Q1305 10V
KZA616WJQZ R1343 3 2 1
3 4 KRC404E 47K R1344
10K
5 6 5.0 0.0
F 0: SP_MUTE
1: SW_MUTE 7 8
4.7K 0.0
2: L_MUTE
3: SPD_SEL
4: AMP_MUTE D1301
5: OPT_MUTE KDS4148
6: AMP_PROTECT NC NC NC VHD
7: AMP_STANDBY 1 2 3 4 5 6 7 8
D1305
C1301
0.1u EXP I/O IC1301 1
25V LA79200V 3
2
SDA0 TO MAIN2(A_TERM)
1
1SS361
R1302
1 2
3 4
R1322
0
D 5 6
7 8
2K R1326
0
TO MAIN4(AMP)
C
3
R1317 1K
SP_LP
1SS361
D1310
1SS361
1SS361
D1312
D1307
SP_LN
TO MAIN8(UCOM)
1
SP_RN
MUTE_A_ALL R1318 1K
SP_RP
Q1304
R1329
R1321
R1325
R1330
KRC404E
47K
47K
TO MAIN16(POWER2)
0
0.0
AC_DET
2.9 R1323 R1308
B 10K 2.2K
0.7 0.7 4 5 6
0.0
TO MAIN9(CPU)
IMH23T110
Q1306
PGA1OUT_L
C1303 0.2
10u
PGA1OUT_R 10V R1314
R1341 47K R1315
15K 10K 3 2 1 MAIN UNIT 3/16
Q1307 DUNTKE833WE03
KTA1504SG
SPOUT_LP BUFFER (PWBXE833WJ)
A GND_B
SPOUT_RP
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
9–5
MAIN4(AMP)
J
N_STANDBY
DUNTKE833WE03
R2719 (PWBXE833WJ)
I 5.6K
N_PROTECT C2725
R2752 0.1u
220K 25V
F
AMP_MUTE L2701
VS 22uH
C2730
PA343WJPZ
Q2704 0.22u
25V
KRC404E
H
L2702 C2726
TO MAIN16(POWER2) 22uH 0.1u
PA343WJPZ 25V
UR13V
FB2706
A206WJ
C2717 C2724
C2710 1u 1u
RMZ
470u 25V 25V 25V
G
32
31
30
29
28
27
26
C2711
0.1u
25V
OUTML
OUTML
OUTPL
OUTPL
PVDDML
PVSSL
PVDDPL
C2712
10u
10V PVDDREG GAIN1
25
1
AVDD GAIN0
2
24
KZA616WJQZ
TO MAIN3(AMP IF) C2704
R2731
1u 25V
SP_LP
KZA114WJ
INLP IC2701 NCDRC1 0
3
23
C2705 YDA148QZ
1u 25V
KZA114WJ R2726
SP_LN ILM NCDRC0
4
22
0
E
VREF CKIN
5
21
33
C2713
C2706 0.1u
1u 25V 25V
KZA114WJ
NC
20
C2707 75K
1u 25V
KZA114WJ
SP_RP INRP MUTEN
7
19
R2744
22
AVSS PROTN
D
8
18
R2715
220K F PLIMIT SLEEPN
17
9
P2701
PVDDMR
PVDDPR
OUTMR
OUTMR
OUTPR
OUTPR
PVSSR
R2742 NA160WJ
R2717
27K FB2702
27K A206WJ
4 LCH(+)
FB2703
10
11
12
13
14
15
16
A206WJ
C R2753
3 LCH(-)
68K F FB2704
A206WJ
C2748 2 RCH(-)
100P FB2705
R2754 A206WJ
22K F C2716 C2723 RCH(+)
1u 1u
1
25V 25V
SP To EX SP
B C2727
0.1u C2737 C2740
25V 150P 150P
C2738 C2741
L2703 150P 150P
22uH
PA343WJPZ C2731 GND_B
0.22u
25V
L2704 C2728
A 22uH 0.1u
PA343WJPZ 25V
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
9–6
MAIN5 (HDMI_SW1)
TO MAIN17(SP_IF)
SP_CLKN
MAIN UNIT 5/16
SP_CLKN
SP_CLKP
SP_CLKP DUNTKE833WE03
(PWBXE833WJ)
J
SP_D0N
SP_D0N
SP_D0P TO MAIN9(CPU)
SP_D0P
SP_D1N
SP_D1N
SP_D1P
SP_D1P
SP_D2N
SP_D2N
R1665 C1624
R1663 10K J 0.1u
SP_D2P 10K 10V
SP_D2P TO MAIN8(UCOM)
HDMI_CEC_O_UCOM
SP_DDC5V HDMI_CEC_I_UCOM
SP_DDC5V
SP_HPD
SP_HPD
SP_SCL
SP_SCL
5 4 C1623
SP_SDA 0.1u
SP_SDA 10V 8 9 10 11 12 13 14
VCC OUT
BU3.3V 7 6 5 4 3 2 1
D1601 R1602
RB520S30 27K
GND_B
TO MAIN8(UCOM)
TO MAIN6(HDMI-SW2) SP_CEC_O_UCOM
HDMI_CEC_IN
SP_CEC_I_UCOM
R1606 R1610
10K 10K J
TO MAIN15(POWER1)
D3.3V
H R1609
D1608
MA152WK
Q1610
D1606 KTA1535T
0 J FB1605
EXA523WJ A192WJ 5 4 C1602
1
5.6V 0.1u
TO MAIN16(POWER2) 3 VCC OUT 10V
5V 2
J
J
R1615
R1618
IC1603
47K
47K
R1638
10K
TC7SH17U
J NC IN GND Shumit Buffer
Q1609 R1639
330
KRC402E 1 2 3
TO MAIN17(SP_IF)
D1602 D1603
1PS226 1PS226 SP_CEC
3 3
SC1601
ZA149WJQZ
1 2 1 2
G 21 23
TMDS1_CLKN_
OUT4- IN4-
TMDS1_CLKN
9
TO MAIN9(CPU)
SP_D2N
SP_D1N
SP_D0N
SP_D2P
SP_D1P
SP_D0P
SP_CLKN
SP_CLKP
TMDS_SW_D0N
TMDS_SW_D1N
TMDS_SW_D2N
TMDS_SW_D0P
TMDS_SW_D1P
TMDS_SW_D2P
TMDS_SW_CLKN
TMDS_SW_CLKP
TMDS1_CLKP_ TMDS1_CLKP
19 OUT4+ IN4+ TMDS_SW_CLKN
10
HDMI_DDC5V_IN1
18
TMDS1_D0N_ TMDS1_D0N TMDS_SW_CLKP
17 OUT3- IN3-
11
6
HDMI_DDC_SDA_IN1
HDMI_DDC_SCL_IN1
HDMI_DDC_SDA_IN1
HDMI_DDC5V_IN1
16 TMDS_SW_D0N
HDMI_HPD_IN1_
0 J TMDS_SW_D0P
14
HDMI_CEC_IN TMDS1_D1N_ TMDS1_D1N
13 OUT2- IN2- TMDS_SW_D1N
13
C1634
TMDS1_CLKN_ 10u C1617 C1619
12 10V 0.1u 1000P
TMDS1_D1P_ TMDS1_D1P KZA616WJQZ TMDS_SW_D1P
11 OUT2+ IN2+
14
TMDS_SW_D2P
8
TMDS1_D0P_ TMDS1_D2P_ TMDS1_D2P
3
4
4
7 OUT1+ IN1+
16
TMDS1_D1N_
6
FA116WJ
FA116WJ
FA116WJ
FA116WJ
L1601
L1603
L1604
L1602
5
IC1601 R1646
F 4
TMDS1_D1P_
TMDS1_D2N_ CM123408
4.7K
2
1
1
3
ESD Clamp array
2
TMDS1_D2P_
1
20 22
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
GND_B
R0X2P R0X1P R0X0P R0XCP VCC33 TXCP TX0P TX1P TX2P
R0X2N R0X1N R0X0N R0XCN TXCN TX0N TX1N TX2N TPWR_CI2CA
R1657 TO MAIN13(CONN)
10 J
TMDS1_CLKN
R1XCN CSCL SCL1
54
1
D1609
TO MAIN6(HDMI-SW2) MA152WK R1658
10 J
TMDS1_CLKP
1 R1XCP CSDA SDA1
53
2
3 R1660
2.2K
2 TMDS1_D0N
J
E
R1X0N INT
J
52
3
R1621
R1620
47K
47K
R1603
0 J
TMDS1_D0P
R1X0P CEC_D
51
4
TMDS1_D1N
NC
R1X1N CEC_A
50
5
D1607 D1610
1PS226 1PS226
C1613 TMDS1_D1P
3 3 R1X1P R4PWR5V
49
6
10u
10V
KZA616WJQZ R1651
47K J
TMDS1_D2N
R1X2N DSCL4
48
7
1 2 1 2 R1652
C1614
47K J
0.1u TMDS1_D2P
R1X2P DSDA4
47
10V
8
SC1602
R1688
ZA171WJ R1671
100K J
10 J R1668
VCC33 R3PWR5V 0
46
9
21 23 R1640 10K
SII9187
TMDS2_CLKN_ TMDS2_CLKN
RSVD 1u 10V
NC
1000P HPD3
45
10
19 KZA520WJQZ
HDMI_DDC5V_IN2 TMDS2_CLKP_ TMDS2_CLKP
HDMI_DDC_SDA_IN2
R1653
HDMI_DDC_SCL_IN2
18 OUT4+ IN4+
10
7
HDMI_DDC5V_IN2
47K J
TMDS2_CLKN
HDMI_HPD_IN2_
17 R2XCN DSCL3
44
11
R1654
HDMI_DDC_SCL_IN2
15 47K J
TMDS2_CLKP
TMDS2_D0P_ TMDS2_D0P R2XCP DSDA3
43
12
14 OUT3+ IN3+
12
13 R1689
TMDS2_CLKN_ TMDS2_D1N_ TMDS2_D1N TMDS2_D0N HDMI_DDC5V_IN2
12 OUT2- IN2- R2X0N R2PWR5V 100K J
42
13
13
4
R1672
TMDS Input2 11 C1628 10 J
TMDS2_CLKP_ TMDS2_D1P_ TMDS2_D1P 1u 10V
10 OUT2+ IN2+ TMDS2_D0P KZA520WJQZ HDMI_HPD_IN2_
14
9
TMDS2_D2N_ TMDS2_D2N R1655
8 OUT1- IN1-
15
10 J
TMDS2_D0P_ TMDS2_D1N HDMI_DDC_SCL_IN2
7 R2X1N DSCL2
40
15
R1656
5 10 J
TMDS2_D1P HDMI_DDC_SDA_IN2
TMDS2_D1P_ R2X1P DSDA2
39
16
C
4
TMDS2_D2N_ IC1602 C1621
0.1u
3
CM123408 TMDS2_D2N 10V
2 R2X2N SBVCC
38
17
20 22
20
21
22
23
24
25
26
28
29
30
31
32
33
34
35
36
27
KZA520WJQZ
R1612
100
CZ
TO MAIN6(HDMI-SW2)
Q1620 R1617
Q1617
J
KTA1504SG 0 CZ
KTC3875SG
R1641
R1642
R1644
R1645
VS
R1613 VS
10
10
10
10
J
J
270K
R1669
R1685
R1670
CZ R1692
10K
B
10
10
TMDS_SW2_CLKP
10K 4700P
TMDS_SW2_D0N
TMDS_SW2_D1N
TMDS_SW2_D2N
TMDS_SW2_D0P
TMDS_SW2_D1P
TMDS_SW2_D2P
C1605 25V
CZ 0.01u CZ
C1603
25V
1u CZB
10V
KZA520WJQZ CZB VS2
C1625 C1626 R1693 Q1618
100K J
100K J
R1687
HDMI_DDC_SCL_IN1
TMDS_SW2_D0N
HDMI_DDC5V_IN1
A
TMDS_SW2_D0N
HDMI_HPD_IN1_
TMDS_SW2_CLKP
SP_DDC5V
TMDS_SW2_CLKP
SP_HPD
SP_SDA
SP_SCL
TMDS_SW2_CLKN
TMDS_SW2_CLKN
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
9–7
MAIN6 (HDMI_SW2)
J
MA152WK
*R1807 TO MAIN5(HDMI-SW1)
0 J
1
TO MAIN16(POWER) 3
5V 2
J
TMDS3_CLKN_ TMDS3_CLKN
J
OUT4- IN4-
9
R1824
8
R1811
47K
47K
TMDS3_CLKP_ TMDS3_CLKP
OUT4+ IN4+
10
TMDS3_D0N_ TMDS3_D0N
OUT3- IN3-
11
TMDS3_D0P_ TMDS3_D0P
OUT3+ IN3+
12
D1817 D1820
1PS226 1PS226
TMDS3_D1N_ TMDS3_D1N TO MAIN13(CONN)
3 3 OUT2- IN2-
13
ZA171WJ
1 2 1 2 TMDS3_D2N_ TMDS3_D2N
21 23 OUT1- IN1-
15
TMDS3_D2P_ TMDS3_D2P
19 OUT1+ IN1+
16
HDMI_DDC5V_IN3 Q1808
18
KTA1535T FB1812
I
17
IC1803
HDMI_DDC_SDA_IN3
HDMI_DDC_SCL_IN3
A192WJ
HDMI_DDC_SDA_IN3
HDMI_DDC5V_IN3
16
HDMI_HPD_IN3_
HDMI_DDC_SCL_IN3 CM123408
15
ESD Clamp array
14
HDMI_CEC_IN
13 R1851
TMDS3_CLKN_ 10K
Q1804
12 J KRC402E R1852
11 330
TMDS Input3 TMDS3_CLKP_
(A-Audio) 10
TMDS3_D0N_
9
8
TMDS3_D0P_
7
TMDS3_D1N_
6
5
TMDS3_D1P_
4
TMDS3_D2N_ TO MAIN5(HDMI-SW1)
3
TMDS_SW2_D0N
TMDS_SW2_D1N
TMDS_SW2_D2N
TMDS_SW2_D0P
TMDS_SW2_D1P
TMDS_SW2_D2P
TMDS_SW2_CLKN
TMDS_SW2_CLKP
2 TMDS_SW2_CLKN
TMDS3_D2P_
1
TMDS_SW2_CLKP
20 22 TMDS_SW2_D0N
TMDS_SW2_D0P
H
GND_B TMDS_SW2_D1N
C1852
10u C1825 C1827
10V 0.1u 1000P
KZA616WJQZ R1920 TMDS_SW2_D1P
D1811
0 J
MA152WK
TMDS_SW2_D2N
TO MAIN5(HDMI-SW1) 1
TMDS_SW2_D2P
HDMI_CEC_IN 3
3
3
4
4
2
J
TMDS3_D2N
TMDS3_D1N
TMDS3_D0N
TMDS3_D2P
TMDS3_D1P
TMDS3_D0P
TMDS3_CLKN
TMDS3_CLKP
R1822
R1847
47K
47K
FA116WJ
FA116WJ
FA116WJ
FA116WJ
L1802
L1804
L1805
L1803
*R1801
0 J
2
2
1
1
R1859
4.7K
TO MAIN5(HDMI-SW1)
D1815 D1818
1PS226 1PS226 HDMI_SW2_DDC5V_IN
3 3
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
R0X2P R0X1P R0X0P R0XCP VCC33 TXCP TX0P TX1P TX2P
R0X2N R0X1N R0X0N R0XCN TXCN TX0N TX1N TX2N TPWR_CI2CA
1 2 1 2 R1870 TO MAIN13(CONN)
SC1802 10 J
NC
54
1
TMDS4_CLKN_ TMDS4_CLKN
G
OUT4- IN4-
9
R1871
10 J
NC
53
2
OUT4+ IN4+
10
R1872
2.2K
19 TMDS4_D0N_ TMDS4_D0N
NC
3
HDMI_DDC_SDA_IN4
HDMI_DDC_SCL_IN4
18
HDMI_DDC5V_IN4
HDMI_HPD_IN4_
17 TMDS4_D0P_ TMDS4_D0P
HDMI_DDC_SDA_IN4 OUT3+ IN3+
12
NC
16 R1X0P CEC_D
51
4
HDMI_DDC_SCL_IN4
15 TMDS4_D1N_ TMDS4_D1N
OUT2- IN2-
13
R1889
14
NC
CZ
NC
12 KZA616WJQZ
NC
10 R1864
TMDS4_D0N_ 47K J
9 TMDS4_D2P_ TMDS4_D2P
NC
8
TMDS4_D0P_ R1865
7 C1802
47K J
TMDS4_D1N_ 0.1u
IC1804
NC
6 R1X2P DSDA4
47
10V
8
5 CM123408
TMDS4_D1P_ R1918
4 ESD Clamp array HDMI_DDC5V_IN5
VCC33 R3PWR5V 100K J
TMDS4_D2N_
46
9
F
TMDS4_D2P_ C1803 HDMI_HPD_IN5_
1 1000P RSVD IC1801 HPD3
KZA520WJQZ
45
10
R1866
20 22 10 J
TMDS4_CLKN HDMI_DDC_SCL_IN5
R2XCN DSCL3
44
11
R1867
10 J
TMDS4_CLKP HDMI_DDC_SDA_IN5
GND_B R2XCP DSDA3
43
12
R1919
TMDS4_D0N 100K J HDMI_DDC5V_IN4
R2X0N R2PWR5V
42
13
R1888
*R1802 C1837 10 J
0 J 1u 10V
TMDS4_D0P KZA520WJQZ HDMI_HPD_IN4_
R2X0P HPD2
41
14
TO MAIN16(POWER)
D1804 R1868
10 J
MA152WK TMDS4_D1N HDMI_DDC_SCL_IN4
R2X1N DSCL2
40
15
3 10 J
TMDS4_D1P HDMI_DDC_SDA_IN4
R2X1P DSDA2
39
16
2 TMDS5_CLKP_ TMDS5_CLKP
J
7
R1823
R1849
0.1u
47K
47K
TMDS4_D2N 10V
TMDS5_D0N_ TMDS5_D0N R2X2N SBVCC
38
17
OUT3- IN3-
11
C1830
1000P
TMDS5_D0P_ TMDS5_D0P TMDS4_D2P
E
OUT3+ IN3+ R2X2P MICOM_VCC33
37
12
18
5
*D1816 *D1819
1PS226 1PS226 TMDS5_D1N_ TMDS5_D1N R3XCN R3X0N R3X1N R3X2N VCC33 DSDA0 HPD0 DSDA1 HPD1
OUT2- IN2-
13
19
20
21
22
23
24
25
26
28
29
30
31
32
33
34
35
36
27
3
ZA171WJ R1808
100
CZ
NC
TMDS5_D2N_ TMDS5_D2N
1 2 1 2 OUT1- IN1-
15
21 23
TMDS5_D2P_ TMDS5_D2P Q1822
J
TMDS5_CLKN
TMDS5_CLKP
TMDS5_D0N
TMDS5_D1N
TMDS5_D2N
TMDS5_D0P
TMDS5_D1P
TMDS5_D2P
R1916
VS
10K
19
R1809
J
HDMI_DDC5V_IN5
270K Q1819 R1861
18
R1854
R1855
R1857
R1858
*IC1805 CZ KTC3875SG 0
47K
47K
HDMI_DDC_SDA_IN5
CZ
HDMI_DDC_SCL_IN5
10
10
17 R1810 VS
HDMI_DDC5V_IN5
CM123408 10K
HDMI_HPD_IN5_
16 C1838 C1815
CZ 0.01u R1812
ESD Clamp array C1817 4700P
25V 25V 470
15 1u
14 10V
CZB CZB CZ
HDMI_CEC_IN KZA520WJQZ
13
TMDS5_CLKN_ R1813
12 C1835 R1856 100K
100K J
47K CZ
1u VS2
R1917
11 C1804 10V CZ
TMDS Input5 TMDS5_CLKP_ 10u C1826 C1828 KZA520WJQZ C1819 Q1820
10 10V 0.1u 1000P
TMDS5_D0N_ KZA616WJQZ 0.047u VS Q1821 2SC3265Y R1862
9 GND_B 10V
KTC3875SG 1
HDMI_DDC_SDA_IN3
HDMI_DDC_SCL_IN3
CZB CZ
8
HDMI_DDC5V_IN3
HDMI_HPD_IN3_
TMDS5_D0P_
D
7
TMDS5_D1N_
6
J
R1885
5
10
TMDS5_D1P_
4
TMDS5_D2N_
3
2
TMDS5_D2P_
1
20 22
D1805
MA152WK
GND_B
1
3
TO MAIN16(POWER2)
C
D1808
MAZ9120H
1 2
R1825
75
1/10W PCIN_R
3 R1806 0
R1881 PC_R_CM
47 CZ
TO MAIN9(CPU)
D1809
MAZ9120H HDMI_WP
FB1804
0093GE
R
FB1805 1 2
R1826
0093GE 75
1/10W PCIN_G
SC1804 R1848 R1850
NA770WJ 47K
FB1806 47K
3 R1842 0
0093GE R1882 PC_G_CM
5 4 3 2 1
47 CZ
B
17 10 9 8 7 6 16
D1810
15 14 13 12 11 MAZ9120H
J
1 2
R1827
R1899
C1849
R1900
R1901
47K
75 10u
10
10
A
A045WJ J 1u CH
2 100K 220 RGB_L
3 RGB_R
RGB_R
1 FB1803 RGB_R
R1817 C1810
A045WJ
220 J CH
1u RGB_L
CYB RGB_L
R1814 GND_B
100K
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
9–8
MAIN7 (PANEL)
TO_MAIN16(POWER2) MAIN UNIT 7/16
J
5V DUNTKE833WE03
TO_MAIN15(POWER1)
D3.3V
(PWBXE833WJ)
L2606
FA154WJ P2601
WA659WJQZ
TO_MAIN9(CPU)
LVDS_TX_0_DATA0_N
L2601
1 3 LW TO LCDCONT
LVDS_TX_0_DATA0_P FA154WJ 2 4
41 GND
FB2604
A375WJQZ
LVDS_TX_0_DATA1_N 1 3 40 TA1-
L2607
LVDS_TX_0_DATA1_P 2 4 FA154WJ 39 TA1+
38 TB1-
I LVDS_TX_0_DATA2_N
L2602
1 3
37 TB1+
LVDS_TX_0_DATA2_P FA154WJ 2 4
36 TC1-
LVDS_TX_0_CLK_N 1 3
L2608 35 TC1+
LVDS_TX_0_CLK_P 2 4 FA154WJ
34 GND
FB2605
A375WJQZ
LVDS_TX_0_DATA3_N 1 3 33 TCLK1-
L2611
LVDS_TX_0_DATA3_P FA154WJ 2 4 32 TCLK1+
31 TD1-
LVDS_TX_0_DATA4_N 1 3
30
H LVDS_TX_0_DATA4_P 2 4
TD1+
L2603 29 TE1-
FA154WJ
28 TE1+
LVDS_TX_1_DATA0_N 1 3 27 GND
L2609 FB2606
A375WJQZ
LVDS_TX_1_DATA0_P FA154WJ 2 4 26 TA2-
25 TA2+
LVDS_TX_1_DATA1_N 1 3
L2604
24 TB2-
LVDS_TX_1_DATA1_P 2 4 FA154WJ
23 TB2+
LVDS_TX_1_DATA2_N 1 3
22 TC2-
G
L2610
LVDS_TX_1_DATA2_P FA154WJ 2 4
21 TC2+
LVDS_TX_1_CLK_N 1 3 20 GND
L2605 FB2607
A375WJQZ
2 4 FA154WJ 19 TCLK2-
LVDS_TX_1_CLK_P
18 TCLK2+
LVDS_TX_1_DATA3_N 1 3
L2612
17 TD2-
LVDS_TX_1_DATA3_P FA154WJ 2 4
16 TD2+
LVDS_TX_1_DATA4_N 1 3
15 TE2-
LVDS_TX_1_DATA4_P 2 4
FB2608 14 TE2+
F A375WJQZ
R2622 13 GND
FB2632
TO_MAIN8(UCOM) 0 A074WJ
12 LVDS_SEL
R2641 0 FB2621
A074WJ
L_R 11 R/L
R2642 0 FB2622
A074WJ
U_D 10 U/D
FB2623
FRAME A074WJ
9 HV_MODE
FB2624
ROMSEL0 A074WJ
8 ROMSEL1
TEMP3 FB2625
A074WJ
TEMP2 7 ROMSEL0
FB2626
A074WJ
TEMP1 6 TEMP3
E FB2627
A074WJ
O_S_SET
5 TEMP2
FB2628
VON A074WJ
4 TEMP1
FB2629
COND_TEST A074WJ
3 PE
R2643 0 FB2630
DET_PNL12V A074WJ
2 OS_EN
R2601 R2602 R2644 0 FB2631
ERR_PNL A074WJ
22K 22K 1 SHIP_EN
2 4 6 8 2 4 6 8
DET_SYNC R2635
R2603 10K
DET_COND 22K
100K
R2636
P2603
NA340WJ
TO_MAIN9(CPU) 1 3 5 7 1 3 5 7 Q2603
D LVDS_SEL KRC404E LB1 TO INV
SHIP_EN FB2613
A204WJ
PNL_EN
*IC2602 6 OFL2 ->
FB2619
M62332FP A074WJ
5 BRT/REG2 ->
3.3 2.3 FB2620
OPWM1 8 Vcc AO1 1 A074WJ
*C2609 4 ERR <-
*R2637 0.1u FB2609
OPWM2
0 CZ 10V A204WJ 3 OFL1
3.3 ->
SOUSA_WP 7 SCL NC 2 FB2618
A074WJ
PNL_I2C_EN
IC2601 *R2638
FB2603
2 VON ->
0 CZ A375WJQZ
HC2G66DP 3.3
6 SDA NC 3 1 GND
PNL_WP
C 1 VCC 8 0.0
5 GND NC 4
C2606
0.1u
R2623
P2602
NA349WJ
TO_MAIN13(CONN) CZB
1M
LP TO LCDCONT
SCL0 2 7 FB2611
A074WJ
15 DET <-
SDA0 FB2610
A074WJ
3 6 14 LCD_EN ->
SCL1 FB2617
A074WJ
13 VCOM_SDA <->
SDA1 FB2616
4 GND 5 A074WJ
12 VCOM_SCL <->
FB2614
A074WJ
I2C Bus SW
11 VCOM_WP ->
FB2638
A074WJ
10 COND_DET <-
B C2602
FB2612
A074WJ
0.1u
0 9 TEST_MODE ->
FB2602
10V A375WJQZ
R2620 8 GND
R2619
0
7 GND
6 GND
5 GND
R2604 R2639
22K 100K
4 VCC
3 VCC
2
A VCC
1 VCC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
9–9
MAIN8 (UCOM)
TO MAIN15(POWER1)
D3.3V
MAIN UNIT 8/16
TO MAIN16(POWER2)
DUNTKE833WE03
J
BU3.3V
C2020
C9720 1000P (PWBXE833WJ)
10u 10V
KZA616WJQZ
TO MAIN14(EXIF)
PNL_DET0
IC2004
PNL_DET0 S24CS08J
POW_SW
SMPOW_
MODEL_A0
MODEL_A1
COND_TEST
PNL_DET1 EEPROM
PNL_DET1 R2015 R2031
10K 10K
PNL_DET2
PNL_DET2 8 VCC A0 1
PNL_DET3
PNL_DET3
PNL_DET4 7 WP A1 2
PNL_DET4 R2061
MODEL_A0 10
MODEL_A0 SCL
6 A2 3
MODEL_A1 R2060
MODEL_A1
10
MODEL_A2 5 SDA GND 4
MODEL_A2
MODEL_A3
MODEL_A3
MODEL_A4
TO MAIN20(HT_UCOM)
I MODEL_A4
GND_B
RC
TO MAIN1(TUNER)
AFT_UCOM
AFT_UCOM TO MAIN9(CPU)
RC
TO MAIN16(POWER2) R2057
DET_5V 10K
DET_5V CZ
DET_15V
TO MAIN13(CONN)
DET_15V RC
TO MAIN7(PANEL)
DET_PNL12V
DET_PNL12V
COND_TEST P2003
U_D
L_R
RS_ON
TEMP3
TEMP2
TEMP1
COND_TEST
PM_REQ
CBOOTS
NA330WJ
ROMSEL0
O_S_SET
N_SRESET
IC2007 C2008
CPU_RXD0_UCOM
CPU_TXD0_UCOM
VON
0.1u
TO R/C RA
AHC1G08W 10V FB2005
A378WJQZ
1 BU+3.3V
TO MAIN12(EXBUS) 4 Y GND 3 STB FB2006
R2050
A378WJQZ
2 OPT+3.3V
100
DET_PNL12V
H B 2
R2004
10K
R2075
FB2014
A378WJQZ
3 GND
R2071
10K FB2007
RC A375WJQZ
R2070
10
4 R/C
10
FB2008
5 Vcc A 1 R2051 LED_G A375WJQZ
R2052 R2078
10
10 5 POWG_LED
10K FB2009
LED_R A375WJQZ
6 POWR_LED
FB2010
TO MAIN9(CPU) C2024 LED_OPC A375WJQZ
STB_CPU
0.1u 7 LED_OPC
10V FB2011
R2033 OPC A375WJQZ
TO MAIN16(POWER2) 100
8 OPC
SMPOW_ FB2012
SMPOW LED_YOYAKU A375WJQZ
R2001 9 LED_YOYAKU
100
AC_DET ILL_LED
10 ILL_LED
R2032
R2006 22K 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
22K
U_D
L_R
VSS
SMPOW
TEMP3
VCC2
TEMP2
TEMP1
POW_SW
RS_ON
CSEN2
ROMSEL0
CBOOT
R2049
AC_DET
O_S_SET
MODEL_A0
MODEL_A1
SYNC_DET
MODEL_C1
MODEL_B0
FRAME
COND_TEST
HDMI_SCDT
G
2.7K 76 RXD_CPU 50
DPOW/LINKPOW
VSYNC/DETECT
POW_SW STB
77 PM_REQ STB 49
P2002 FRAME 8 6 4 2
NA338WJ C2016 R2019 NC
R2047 78 SRESET N_SYSTEM_RST 48
0.1u 10K
TXD_CPU
100 R2017
TO KEY
KM 10V
79 OPC EXE_LED 47 10K R2012
FB2001 10K
A206WJ 7 5 3 1
80 QSTEMP RXD_DBGP 46
GND 4
FB2004
A005WJ AFT_UCOM
STBY_POW 3 81 AFT/AGC TXD_DBGP 45
FB2003 TH2001 GND_B
A005WJ KEY1_
KEY2 2 M1103J03 82 KEY1 CE 44
FB2002 TO MAIN3(AMP IF)
A005WJ KEY2_ MODEL_A2 MUTE_A_ALL
KEY1 1 83 KEY2 MODEL_A2 43 MUTE_A_ALL
MODEL_A3
84 KEY3 MODEL_A3 42 TO MAIN5(HDMI_SW1)
HDMI_CEC_O_UCOM
R2023 MODEL_A4 HDMI_CEC_O_UCOM
R2024 85 NC MODEL_A4 41
47K F R2038
1K HDMI_CEC_I_UCOM
0 ERR_PNL
NC HDMI_CEC_I_UCOM
86 MAIN_TEMP ERR_PNL 40
F NC
87 NC EPM 39
SP_CEC_O_UCOM
SP_CEC_O_UCOM
96 VREF RXD 30
DET_COND
R2009 1K DET_COND
E KEY2_
97 AVCC TXD 29 DET_SYNC
DET_SYNC
CEC_O2
DET_COND
C2012 98 LED_R 28
0.1u I2C_SDA
10V TO MAIN9(CPU)
99 LED_G I2C_SCL 27 RS_BUF_CNT
MUTE_A_ALL
ACCESS_G
AV_LINK_O
DET_SYNC
AV_LINK_I
CEC_O
IRPASS
CNVSS
XCOUT
RESET
CEC_I2
CEC_I
VCC1
XOUT
BYTE
XCIN
P8_4
VSS
NC
XIN
C2027
RC
C2028 C2029
100P 100P 100P TO MAIN7(PANEL)
CCZ CCZ CCZ ROMSEL0
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 ROMSEL0
TEMP3
R2016 1 G1 Vcc 8 TEMP3
10K
TEMP2
TEMP2
2 A1 G2 7 TEMP1
TEMP1
R2018
10K O_S_SET
O_S_SET
3 Y2 Y1 6
5 4
U_D
D C2010 U_D
CD NC R2026
0.1u R2028
10K 100K L_R
10V 10K 4 GND A2 5 L_R
R2002
C2002 IC2001 FRAME
1500P FRAME
S80927NM
R2036
OUT VDD GND
ResetIC 1M
IC2008 TO MAIN12(EXBUS)
R2029
1 2 3
7WH126FU N_SRESET
N_SRESET
10
R2034
TO MAIN9(CPU) 0 J ROMSEL0
C2003
0.1u 10V R2042 TEMP2
R2058
R2064
100 C2026
R2048
10
10
L_R
1
4.7K
1 3 0.1u
R2077 10V
GND_B
R2007 100 TO MAIN13(CONN)
4.7K N_SRESET
RS_ON
2
RS_ON
Q2006
R2044
C TO MAIN9(CPU)
RT1N141U 2
10
ZA023WJQZ
SP_CEC_O_UCOM
CBOOTS
SP_CEC_I_UCOM
20MHz CBOOTS
LED_YOYAKU
MUTE_A_ALL
DET_COND
LED_OPC
DET_SYNC
ILL_LED
LED_G
LED_R
IRPASS
OPC
RC
R2003
1K
Q2003 Q2004
RT1P141U RT1N141U
VS VS
10K
R2072
100K
R2068
GND_B
B
R2020
10K
22K
22K
R2062
R2063
GND_B R2025
10K
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
9 – 10
MAIN9 (CPU)
TO MAIN16(POWER2) MAIN UNIT 9/16
A8V DUNTKE833WE03
CPU_BU_3.3V
BU3.3V
(PWBXE833WJ)
BU_PS_ON
J TO MAIN15(POWER1)
A3.3V TO MAIN14(EXIF)
1
6
C8062 C8064 C8066 CPU_TCK
D3.3V 0.1u 0.1u 0.1u CPU_TCK
10V 10V 10V CPU_TDI
R8078 CPU_TDI
A1.2V 1K CPU_TDO
2
CPU_TDO
D1.1V CPU_TMS
CPU_TMS
D1.8V CPU_TRST
CPU_TRST
3
C8039
TO MAIN13(CONN)
4.7u SCL0
10V C8051 C8052 C8053 C8054 C8055 C8056 C8057 C8058 C8059 SCL0
0.1u 0.1u 0.1u 0.1u 0.1u 0.1u 0.1u 0.1u
Q8001 SDA0
KZA067WJ 10u
C8040 C8041 C8042 C8043 C8044 C8045 SDA0
KZA616WJQZ 10V 10V 10V 10V 10V 10V 10V 10V HN7G04FUA SCL1
0.1u 0.1u 0.1u 0.1u 0.1u 0.01u GND_B GND_B SCL1
10V 10V 10V 10V 10V 25V A3.3V
SDA1
SDA1
CPU_UARXD2_UCOM
CPU_UARXD2_UCOM
CPU_UATXD2_UCOM
CPU_UATXD2_UCOM
I CPU_UARXD1_H
TO MAIN20(HT_UCOM)
CPU_UARXD1_H
CPU_UATXD1_H
TO MAIN7(PANEL) CPU_UATXD1_H
LVDS_TX_0_DATA0_P R8039 N_PARB ONDA12 ONDA10 ONDA6 PDD5 PDD3 PDD1 LVDS_TX_1_DATA1_P LVDS_TX_1_CLK_P LVDS_TX_1_DATA4_P CPU_TDO STB_CPU CPU_TS0_VALID_I
*R8061
TO MAIN10(DDR) 4.7K 1K
LVDS_TX_0_DATA1_N *C8098
F CZ A1 A2 A3 A4 A5 A7 A8 A10 A11 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30
DDR_VREF 470P
LVDS_TX_0_DATA1_P
50V D8001 SOUSA_WP
LVDS_TX_0_DATA2_N PXA018WJ LVDS_SEL LVDS_TX_1_DATA0_N LVDS_TX_1_DATA2_N LVDS_TX_1_DATA3_N HCOM_MSI
DDR_DQ0 PNL_I2C_EN
*R8062 N_ONDCE1 ONDA13 ONDA7 N_POOE N_POCE1 PDD0 PDD7 PACLE LVDS_TX_1_DATA1_N LVDS_TX_1_CLK_N LVDS_TX_1_DATA4_N CPU_TCK HCOM_SCLK CPU_TS0_CLK_I
LVDS_TX_0_DATA2_P
DDR_DQ1 4.7K
LVDS_TX_0_CLK_N F
DDR_DQ2 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 B20 B21 B22 B23 B24 B25 B26 B27 B28 B29 B30
LVDS_TX_0_CLK_P
DDR_DQ3 *C8097 LED0 PNL_EN
GND_B OPWM2 LVDS_TX_0_DATA0_P LVDS_TX_0_DATA2_P LVDS_TX_0_DATA3_P CPU_TS0_SYNC_I
LVDS_TX_0_DATA3_N 1u
DDR_DQ4
16V N_ONDOE N_ONDCE0 ONDA9 ONDA8 PDD2 PDD6 PAALE PDD4 LVDS_TX_0_DATA1_P LVDS_TX_0_CLK_P LVDS_TX_0_DATA4_P CPU_TDI CPU_TMS CPU_TS0_DATA_I
LVDS_TX_0_DATA3_P
DDR_DQ5
LVDS_TX_0_DATA4_N DDR_DQ6 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 C20 C21 C22 C23 C24 C25 C26 C27 C29 C30
LVDS_TX_0_DATA4_P SHIP_EN
DDR_DQ7 TO_MAIN12(EXBUS) TS_VAL_O
LVDS_TX_1_DATA0_N LVDS_TX_0_DATA0_N LVDS_TX_0_DATA2_N LVDS_TX_0_DATA3_N
DDR_DQ8 LVDS_SEL HCOM_RST
H LVDS_TX_1_DATA0_P DDR_DQ4 HDMI_SW_SEL1 ONDD15 ONDD10 ONDD8 LVDS_TX_0_DATA1_N LVDS_TX_0_CLK_N LVDS_TX_0_DATA4_N CPU_TRST CBOOTS TS_CLK_O
DDR_DQ9 SHIP_EN
LVDS_TX_1_DATA1_N
DDR_DQ10 PNL_EN D1 D2 D3 D4 D5 D6 D7 D8 D10 D11 D13 D14 D15 D16 D17 D18 D19 D20 D21 D22 D23 D24 D25 D26 D27 D28 D29 D30
LVDS_TX_1_DATA1_P DDR_DQ11 HDMI_SW2_SEL2 N_POWE
LVDS_TX_1_DATA2_N HDMI_SW_SEL2 TS_SYN_O
DDR_DQ12
TO_MAIN7(PANEL) N_POCE0 ONDD11 ONDD13 ONDD14 I2CEXT TS_DAT_O
LVDS_TX_1_DATA2_P DDR_DQ3
DDR_DQ13 LVDS_SEL
LVDS_TX_1_DATA3_N
DDR_DQ14 SHIP_EN E1 E2 E3 E4 E5 E6 E7 E8 E9 E10 E11 E12 E13 E14 E15 E16 E17 E18 E19 E20 E21 E22 E23 E24 E26 E27 E28 E29
LVDS_TX_1_DATA3_P
DDR_DQ15 PNL_EN PWM_ANA_SW RS_BUF_CNT
LVDS_TX_1_CLK_N
DDR_DQ16 PWM_ANA_SW
DDR_DQ6 DDR_DQ1 HDMI_SW2_SEL1 ONDA11 ONDD12 ONDD9 RST_FLS_CPU CNVss
LVDS_TX_1_CLK_P DDR_DQ17 SOUSA_WP TO MAIN2(A_TERM)
DDR_DQ18 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 F26 F28 F29 F30 R8031 30K
LVDS_TX_1_DATA4_N PNL_WP AIN1_L
V1_L
LVDS_TX_1_DATA4_P DDR_DQ19 PNL_I2C_EN R8032 30K
AIN1_R
CPU_UATXD1_H PM_REQ V1_R
DDR_DQ20 OPWM1
N_DDR_DQS0 DDR_DQS0 DDR_DQ7 CPU_UATXD2_UCOM FLASH_W_CPU TUN_GAIN_SW R8033 30K
DDR_DQ21 OPWM2 AIN2_L
V2_L
DDR_DQ22 G1 G2 G3 G4 G5 G6 G8 G25 G26 G27 G28 G29 G30 R8034 30K
AIN2_R
V2_R
DDR_DQ23
TO_MAIN12(EXBUS) R8049 R8052
DDR_DQ24 4.7K 4.7K CPU_UARXD1_H R8035 30K
TUN_AD_CTL AIN3_L
OPWM2 *R8051 CPU_UARXD2_UCOM TUN_RF_SW V3_L
DDR_DQ25 DDR_DQM0 DDR_DQ2 DDR_DQ0 C8086 C8087 C8088
4.7K C8089 AIN3_R R8036 30K
G
KZA616WJQZ 0.1u 0.1u 0.1u
C8067 C8070 C8073 C8076 C8078 C8080 C8099 C8100 C8101 C8102 0.01u V3_R
DDR_DQ26 H1 H2 H3 H4 H5 H6 10V 10V 10V H25 H26 H27 H28 H29
0.1u 0.1u 0.1u 0.1u 0.1u 0.1u 10u 10u 10u 10u 25V
DDR_DQ27 10V 10V 10V 10V 10V 10V KZA616WJQZ KZA616WJQZ KZA616WJQZ
TO_MAIN2(A_TERM) OPT_OUT
DDR_DQ28
SCL0 SDA0
TO MAIN6(HDMI_SW2)
DDR_DQ29 C1_PLG DDR_DQS1 N_DDR_DQS1 DDR_DQ5
R8037 30K
AIN0_L
DDR_DQ30 C2_PLG J2 J3 J4 J5 J6 C8068 C8071 C8074 C8077 C8079 C8081 C8082 C8083 C8084 C8085 J27 J28 J29 J30 RGB_L
0.01u 0.01u 0.01u 0.01u 0.01u 1000P 1000P 1000P 1000P 1000P R8038 30K
DDR_DQ31 S1_PLG 50V 50V 50V 50V 50V AIN0_R
25V 25V 25V 25V 25V RGB_R
IF_AGC
V1_PLG
DDR_DQM0 OPWM1 SCL1 SDA1
V3_PLG DDR_DQ11 DDR_DQ12 DDR_DQ10 DDR_DQM1
DDR_DQM1
K1 K2 K3 K4 K5 K6 K12 K13 K14 K15 K16 K17 K18 K25 K26 K27 K28 K29 K30 TO MAIN3(AMP I/F)
DDR_DQM2 R8065
OPT_OUT 33
TO_MAIN8(UCOM) CPU_SPDIF_OUT
DDR_DQM3 TUN_SDA
PM_REQ C8037
DDR_DQ13 DDR_DQ14 DDR_DQ9 TUN_SCL PGA0OUT_L
DDR_DQS0 RS_BUF_CNT 1u 16V
R8056 SPOUT_LP
N_DDR_DQS0 4.7K L1 L2 L3 L4 L5 L6 L11 L12 L13 L14 L15 L16 L17 L18 L19 L25 L26 L28 L29 C8038
CNVss PGA0OUT_R 1u 16V
DDR_DQS1 SPOUT_RP
RST_FLS_CPU
C8090
N_DDR_DQS1 0.1u
DDR_DQS2 DDR_CK0P DDR_CK0N DDR_DQ8 DDR_DQ15 25V PGA2OUT_R PGA2OUT_L
CBOOTS NC NC
PGA1OUT_L
N_DDR_DQS2 STB_CPU M2 M3 M4 M5 M6 M10 M11 M12 M13 M14 M15 M16 M17 M18 M19 M27 M28 M29 M30 PGA1OUT_L
F DDR_DQS3 PGA1OUT_R
PGA1OUT_R
N_DDR_DQS3
N_DDR_CS0 N_DDR_CAS DDR_A0 DDR_ODT0
NC PGA1OUT_L PGA1OUT_R PGA0OUT_R PGA0OUT_L
DDR_ODT0 TO_MAIN20(HT_UCOM) PGA2OUT_L
N1 N2 N3 N4 N5 N6 N10 N11 N12 N13 N14 N15 N16 N17 N18 N19 N25 N26 N27 N28 N29 N30
TO MAIN12(EXBUS) N_DDR_WE PGA2OUT_L
HCOM_RST
PGA2OUT_R
N_DDR_CAS HCOM_SCLK C8008 C8009 C8010 PGA2OUT_R
N_POCE0
C8007 10u CKZ 0.1u 10u CKZ
N_DDR_RAS HCOM_MSO DDR_A6 DDR_A2 N_DDR_RAS
N_POCE1 DDR_A8 DDR_A4 10V
0.1u
N_DDR_CS0 HCOM_MSI 10V GND_B GND_B
N_POOE P1 P2 P3 P15 P16 P17 P18 P19 P25 P26 P28 P29
P4 P5 P6 P10 P11 P12 P13 P14
DDR_BA0
PDD0
DDR_BA1 TO_MAIN13(CONN)
PDD1
PDD2 DDR_BA2 I2CEXT DDR_A1 DDR_A11
NC NC NC
PDD3 R3
DDR_A0 R2 R4 R5 R6 R10 R11 R12 R13 R14 R15 R16 R17 R18 R19 R25 R26 R28 R29 R30
PDD4 DDR_A1 C8016
TO_MAIN1(TUNER)
PDD5
DDR_A2
IC8001 C8005 C8006 SD_CVBS0 0.047u
R8016
CVBS3
0.1u 10u CKZ 10V 0
PDD6 IXC579WJQZ 10V
DDR_A3 NC NC NC
PDD7 GND_B C8017
DDR_A4 T1 T2 T3 T4 T5 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T21 T23 T24 T25 T26 T27 T28 T29 T30 C8013 SD_CVBSN 1u
PAALE 10P CVBS3_CM
NC 10V
E
DDR_A5 R8012
DDR_A9 50V
PACLE DDR_A12 DDR_A10 0 D
DDR_A6
N_PARB TO_MAIN2(A_TERM)
DDR_A7 C8018
SD_CVBS1 R8018
N_POWE R8011 X8001 0.047u
DDR_A8 U1 U2 U3 U4 U5 U10 U11 U12 U13 U14 U15 U16 U17 U18 U21 U22 U23 U24 U25 U26 U27 U28 U29 CVBS1_M
SCA039WJ 10V 0
1M
DDR_A9 AIN3_R AIN3_L AIN2_R AIN2_L 27MHz
DDR_A7
DDR_A10 DDR_A3
TO MAIN18(LAN)
DDR_A11 R8013
ONDA6 C8012
0 12P C8019 R8020
DDR_A12 V1 V2 V3 V4 V5 V10 V11 V12 V13 V14 V15 V16 V17 V18 V20 V21 V22 V23 V24 V26 V27 V28 V29 V30 SD_CVBS2 0.047u
ONDA7 50V CVBS2_M
DDR_CKE AIN0_R AIN0_L AIN1_R AIN1_L 10V 0
DDR_BA0 G
ONDA8 DDR_BA1 DDR_A5 GND_B
DDR_CK0P DDR_VREF
ONDA9 TO_MAIN1(TUNER)
DDR_CK0N
ONDA10
DDR_CK1P TUN_GAIN_SW W1 W2 W3 W4 W5 W10 W11 W12 W13 W14 W15 W16 W17 W18 W20 W21 W22 W23 W24 W26 W27 W28 W29 W30
ONDA11 C8020
DDR_CK1N TUN_RF_SW SD_L1 0.047u
XTALO Y_SIG1
ONDA12 R8009 10V
N_DDR_WE DDR_CKE DDR_BA2 DDR_DQ18 DDR_DQ21 XTALI
ONDA13 4.7K
C8021
SD_C1 0.047u
ONDD8 C_SIG1
Y2 Y3 Y4 Y5 Y6 Y10 Y11 Y12 Y13 Y14 Y15 Y16 Y17 Y18 Y20 Y21 Y22 Y23 Y24 Y26 Y27 Y28 Y29 Y30 10V
ONDD9
ONDD10 C8022
D
DDR_DQ20 DDR_DQ19 DDR_DQ23 DDR_DQ16 SOY0 4700P
ONDD11 50V
NC C8023 R8072
ONDD12 SD_Y0 0.01u
AA2 AA3 AA26 AA27 COMP1_Y
AA1 AA4 AA5 AA6 AA10 AA11 AA12 AA13 AA14 AA15 AA16 AA17 AA18 AA28 AA29 25V 18 R8024
ONDD13
IF_P C8091 56
ONDD14 TO_MAIN8(UCOM) SD_Y0N 0.01u
DDR_DQ22 DDR_DQ17 DDR_DQ28 COMP1_Y_CM
25V
ONDD15 KEY1_CPU C8024 R8073
N_ONDOE SD_PB0 0.01u
R8060 AB2 AB26 AB27 AB30 KEY2_CPU COMP1_PB
AB1 AB3 AB4 AB5 AB6 AB7 AB10 AB11 AB12 AB13 AB14 AB15 AB16 AB17 AB18 AB20 AB28 AB29 25V 18 R8025
N_ONDCE0 4.7K
TO_MAIN5(HDMI_SW1) SD_INCM_SIF1 SD_SIF1 IF_N POW_SW_CPU C8025 R8074 56
N_ONDCE1 SD_PR0 0.01u
N_DDR_DQS2 DDR_DQS2 DDR_DQM2 THERMO_CPU COMP1_PR
25V 18 R8026
R8058 TMDS_SW_D1P
4.7K C8026 56
TMDS_SW_D1N C8011 SD_PBR0N 0.01u
AC2 AC26 AC27 AC28 AC29 0.1u COMP1_PBR_CM
AC3 AC4 AC5 AC6 AC30 25V
TMDS_SW_D2P RDA8001 10V
C8092
TMDS_SW_D2N v SOY1
N_DDR_DQS3 4700P
DDR_DQS3 DDR_DQM3
GND_B CPU_ADIN6 50V
TMDS_SW_D0P C8027 R8075
SD_Y1 0.01u
COMP2_Y
TMDS_SW_D0N TO_MAIN13(CONN) 25V 18 R8027
AD1 AD2 AD3 AD4 AD5 AD6 AD26 AD27 AD28 AD29
TMDS_SW_CLKP C8060 C8061 C8063 C8065 C8069 C8072 C8075 C8046 CPU_UARXD0_RS C8093 56
0.1u 0.1u 0.1u 0.1u 0.1u 0.1u 0.1u 0.1u SD_CVBSN SD_CVBS0 SD_Y1N 0.01u
R8054 COMP2_Y_CM
TMDS_SW_CLKN 10V 10V 10V 10V 10V 10V 10V 10V CPU_UATXD0_RS 25V
C
DDR_DQ31 DDR_DQ27 DDR_DQ25 10K C8028
SD_PB1 R8076
0.01u
J8001 TO_MAIN16(POWER2) 25V 18 R8028
COMP2_PB
A206WJ
AF2 AF3 AF4 AF5 AF6 AF7 AF8 AF9 AF11 AF12 AF13 AF14 AF15 AF16 AF17 AF18 AF19 AF20 AF21 AF22 AF23 AF26 AF27 AF28 AF29 AF30 GND_B
USB_DP0 0 TO_MAIN6(HDMI_SW2)
USB_DP C1_PLG PNL_ON POW_SW_CPU CPU_TN0 SD_C1 SD_L1
3
VXA074WJ C8032
FB8002 39V SD_B 0.01u
39V USB_PWRFLT0 CPU_HDMI_HPG_IN5 DBG_uP_TX PCIN_B
A206WJ 1.1pF 25V
1.1pF R8007 C8095
SMPOWHOLD TO_MAIN17(SP_IF) SD_BN 0.01u
R8003 R8004 0 PC_B_CM
SP_DDC5V_EXT R8048 SP_DDC5V_EXT 25V
100 F 39 F 4.7K NC NC NC SP_DDC5V_EXT C8033
SD_G 0.01u
USB_PWRFLT0 AH2 AH10 AH20 AH21 AH22 AH23 AH24 AH25 AH26 AH27 AH28 SP_HPD_EXT PCIN_G
AH1 AH3 AH4 AH5 AH6 AH7 AH8 AH9 AH11 AH12 AH13 AH14 AH15 AH16 AH17 AH18 AH19 AH29 AH30
SP_HPD_EXT 25V
C8034
S1_PLG SD_GN 0.01u
USB_PWRON0 USB_PWRON0 HDMI_SW1_TPWR OPCTRL8 SD_B SOG SOY1 SD_Y1N SD_PR1 SOY0 SD_Y0N SD_PR0 KEY1_CPU PC_G_CM
5 4 C8004 C2_PLG 25V
DBG_uP_RX AFT_CPU C8096
4.7u CPU_HDMI_HPD_SW OPWRSB SOG 4700P
VOUT OC SP_HPD_EXT
B
10V 50V
NC NC NC NC
KZA067WJ PCIN_HD
AJ1 AJ2 AJ3 AJ4 AJ5 AJ6 AJ7 AJ8 AJ9 AJ10 AJ11 AJ12 AJ13 AJ14 AJ15 AJ16 AJ17 AJ18 AJ19 AJ20 AJ21 AJ22 AJ23 AJ24 AJ25 AJ26 AJ27 AJ28 AJ29 AJ30 PCIN_HD
USB:500mA max IC8002 V1_PLG PCIN_VD
USB_DN0 TMDS_SW_D0N TMDS_SW_D2N OPWM0 PCIN_VD SD_BN SD_GN SD_RN SD_Y1 SD_PB1 SD_Y0 SD_PB0 DACOUT1 CPU_ADIN5 THERMO_CPU TO_MAIN5(HDMI_SW1) PCIN_VD
BD6538G V3_PLG
CPU_UARXD0_RS
TMDS_SW_CLKN TMDS_SW_D1N SDA_HDMI_SW HDMI_WP TO_MAIN1(TUNER)
HDMI_WP
NC NC NC C8035
TO_MAIN6(HDMI_SW2) SD_SIF1 0.01u
VIN GND EN AK4 AK8 SIF
AK2 AK3 AK5 AK6 AK7 AK9 AK10 AK11 AK13 AK14 AK16 AK17 AK19 AK20 AK22 AK24 AK26 AK27 AK28 AK29 AK30 25V
LED0 HDMI_WP
1 2 3 USB_DP0 TMDS_SW_D0P TMDS_SW_D2P RC PCIN_HD SD_G SD_R SD_PBR1N SD_PBR0N N_CPU_RST CPU_ADIN6 CPU_ADIN4 C8036
TO_MAIN16 (POWER2) R8005
SD_INCM_SIF1 0.01u
TMDS_SW_CLKP TMDS_SW_D1P SCL_HDMI_SW CPU_UATXD0_RS KEY2_CPU SIF_CM
5.1K 25V
5V
R8001 F
GND_B
100
GND_B
CEC_CPU
R8079
C8001
C8002 C8003 75 GND_B
TO_MAIN13(CONN)
10V 10u R8002
0.1u 0.1u
KZA616WJQZ 10V 10K
10V TO_MAIN12(EXBUS) TUN_SCL
N_CPU_RST TUN_SDA
GND_B
TO_MAIN8(UCOM) TO_MAIN1(TUNER)
A RC
TUN_AD_CTL
IF_AGC
IF_P
IF_N
AFT_CPU
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
9 – 11
MAIN10 (DDR)
MAIN UNIT 10/16
KZA616WJQZ
10V
DUNTKE833WE03
C8184
10V
J
KZA520WJQZ
NC
10u
A1 A2 A3 A7 A8 A9
(PWBXE833WJ)
C8174
1u
N_DDR_DQS1
B1 B2 B3 B7 B8 B9
DDR_DQ14 DDR_DQM1 DDR_DQS1 DDR_DQ15
TO MAIN9(CPU)
C8180
DDR_DQ0
0.1u
0.1u
C8186
C1 C2 C3 C7 C8 C9
TO MAIN15(POWER1)
DDR_DQ9 DDR_DQ8 DDR_DQ1
D1.8V DDR_DQ2
DDR_DQ3
D1 D2 D3 D7 D8 D9
DDR_DQ5
GND_B
NC DDR_DQ6
E1 E2 E3 E7 E8 E9
DDR_DQ7
N_DDR_DQS0
DDR_DQ8
TO MAIN9(CPU) DDR_DQ9
DDR_VREF F1 F2 F3 F7 F8 F9 DDR_DQ10
DDR_DQ6 DDR_DQM0 DDR_DQS0 DDR_DQ7
DDR_DQ11
DDR_DQ12
C8181
0.1u
0.1u
DDR_DQ13
C8187
G1 G2 G3 G7 G8 G9
DDR_DQ1 DDR_DQ0
DDR_DQ14
DDR_DQ15
H DDR_DQ4 DDR_DQ3 DDR_DQ2 DDR_DQ5
DDR_DQ16
H1 H2 H3 *IC8152 H7 H8 H9
IXC768WJQZ DDR_DQ17
DDR_DQ18
DDR_DQ21
DDR_DQ24
DDRM_BA2 DDR_DQ25
DDRM_BA0 DDRM_BA1 N_DDRM_CAS N_DDRM_CS0
L1 L2 L3 L7 L8 DDR_DQ26
G DDR_DQ27
DDR_DQ28
DDRM_A10 DDRM_A1 DDRM_A2 DDRM_A0
10V
KZA520WJQZ
M2 M3 M7 M8 M9 DDR_DQ29
C8190
DDR_DQ30
1u
DDR_DQ31
DDRM_A3 DDRM_A5 DDRM_A6 DDRM_A4
N1 N2 N3 N7 N8
TO MAIN9(CPU)
DDR_A0
DDR_A0
VRS 10 *R8181
DDR_A1
DDR_A1 DDR_CKE DDRM_CKE DDRM_A7 DDRM_A9 DDRM_A11 DDRM_A8
DDR_A2 N_DDR_WE 8 7 N_DDRM_WE P2 P3 P7 P8 P9
DDR_A2
DDR_A3 DDR_BA2 6 5 DDRM_BA2
DDR_A3
DDR_BA0 4 3 DDRM_BA0
DDR_A4
F
DDR_A4 2 1 DDRM_A12 DDR_DQM0
DDR_A5 R1 R2 R3 R7 R8
DDR_A5 DDR_DQM1
0.1u
NC NC NC
C8175
DDR_A6
DDR_A6 VRS 10 *R8182 DDR_DQM2
DDR_A7 DDR_BA1 DDRM_BA1
DDR_A7 DDR_DQM3
DDR_A3 8 7 DDRM_A3
DDR_A8
DDR_A8 DDR_A7 6 5 DDRM_A7
DDR_A9
DDR_A9 DDR_A12 4 3 DDRM_A12
DDR_A10 2 1
DDR_A10
DDR_A11
DDR_A11
VRS 10 *R8183
DDR_A12
DDR_A9 DDRM_A9
10V
DDR_A12
KZA616WJQZ
DDR_A1 8 7 DDRM_A1
C8185
10V
KZA520WJQZ
DDR_BA0 NC
10u
DDR_BA1 N_DDR_DQS3
2 1 DDR_DQS1
E DDR_BA2
DDR_BA2
N_DDR_DQS1
VRS 10 *R8184 DDR_DQS2
DDR_CKE
DDR_CKE DDR_A0 DDRM_A0 B1 B2 B3 B7 B8 B9
N_DDR_DQS2
N_DDR_CS0 N_DDR_CS0 8 7 N_DDRM_CS0 DDR_DQ30 DDR_DQM3 DDR_DQS3 DDR_DQ31
N_DDR_CS0 DDR_DQS3
N_DDR_CAS 6 5 N_DDRM_CAS
N_DDR_DQS3
4 3
N_DDR_RAS
C8182
0.1u
N_DDR_RAS
0.1u
2 1
C8188
C1 C2 C3 C7 C8 C9
N_DDR_CAS
N_DDR_CAS DDR_DQ25 DDR_DQ24
N_DDR_WE
N_DDR_WE VRS 10 *R8185
DDR_ODT0 DDR_ODT0 DDRM_ODT0
DDR_ODT0
N_DDR_RAS 8 7 N_DDRM_RAS D1 D2 D3 D7 D8 D9
R8151 0 DDR_DQ28 DDR_DQ27 DDR_DQ26 DDR_DQ29
DDRM_CK0P DDR_A4 6 5 DDRM_A4
DDR_CK0P
R8152 0 DDRM_CK0N
DDR_A8 4 3 DDRM_A8
DDR_CK0N
R8153 0 2 1 NC
D
DDRM_CK1P
DDR_CK1P E1 E2 E3 E7 E8 E9
R8154 0 DDRM_CK1N N_DDR_DQS2
DDR_CK1N
VRS 10 *R8186
DDR_A11 DDRM_A11
DDR_A10 8 7 DDRM_A10
F1 F2 F3 F7 F8 F9
DDR_A5 6 5 DDRM_A5
DDR_DQ22 DDR_DQM2 DDR_DQS2 DDR_DQ23
4 3
2 1
C8183
0.1u
0.1u
C8189
G1 G2 G3 G7 G8 G9
DDRM_CK0P
DDR_DQ17 DDR_DQ16
100
R8157
C DDR2 MEMORY
DDRM_CK1P
DDR_VREF 512Mbit 1066M DDRM_CK1P
J1 J2 J3 J7 J8 J9
0.1u
100
R8158
DDRM_CK1N C8179
DDRM_CKE N_DDRM_WE N_DDRM_RAS DDRM_CK1N DDRM_ODT0
K2 K3 K7 K8 K9
M2 M3 M7 M8 M9
C8191
1u
DDRM_A12
R1 R2 R3 R7 R8
0.1u
NC NC NC
C8177
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
9 – 12
MAIN11 (EPROM)
J
I TO MAIN15(POWER1)
D3.3V
H
TO MAIN16(POWER2)
5V
IC8453 CZB
C8451
TO MAIN12(EXBUS) IXC721WJQZ 0.1u
512Mbit
N_POCE1 1 NC NC 48
N_POCE1 0.0 0.0 0.0 3.3
N_POOE
G N_POOE 2 NC NC 47
1 E0 VCC 8
TO MAIN13(CONN)
R8455
0.0 0.0
4.7K
R8453
4.7K
PDD0
PDD0
NC
0.0 3.1
3 NC 46 2 E1 WC 7 I2CEXT
PDD1 0.0 0.0 R8456
PDD1
4 NC NC 45 47 CZ
PDD2 0.0 0.0 3.3 3.3
PDD2 3 E2 SCL 6 SCL0
PDD7
PDD3 5 NC I/O7 44 7 8 R8457
PDD3 0.0 0.0 0.0 47 CZ
PDD6 4 VSS
3.3
PDD4 I/O6 SDA 5 SDA0
PDD4 R8451 6 NC 43 5 6
47
0.0 0.0
PDD5 N_PARB PDD5
F PDD5 7 R/B# I/O5 42 3 4
3.3 0.0
PDD6
PDD6 N_POOE PDD4
IC8451 SCL1
8 RE# I/O4 41 1 2
PDD7 3.3 0.0
PDD7 N_POCE1
9 CE# NC 40 R8458 SDA1
PAALE 3.3 0.0 0
PAALE
PACLE 10 NC NC 39
PACLE 0.0 0.0
N_PARB 11 NC PRE 38
N_PARB 0.0 0.0 CZB
E N_POWE
N_POWE
12 VCC 37 C8460
VCC
C8455 3.3 3.3 0.1u
C8456
0.1u 13 VSS 36 0.1u
VSS
CZB 0.0 0.0 CZB R8463
14 35 0 CZ
NC NC
0.0 0.0
15 NC NC 34 0.0 3.3
0.0 0.0 1 A0 VCC 8
PACLE
16 CLE NC 33
0.0 0.0 0.0 0.0
D PAALE
ALE I/O3 32 7 8
PDD3 2 A1 WP 7
17
0.0 0.0 R8474
N_POWE PDD2 0.0 3.3 47 CZ
18 WE# I/O2 31 5 6 SCL
3.3 0.0 R8462 3 A2 6
PDD1 0 CZ R8475
19 WP# I/O1 30 3 4 0.0 3.3 47 CZ
3.3 0.0
4 GND SDA 5
PDD0
20 NC I/O0 29 1 2
0.0 0.0
21 NC NC 28 R8459
C
0.0 0.0 0 IC8454
22 NC NC 27 S24CS64A
0.0 0.0
EEPROM
23 NC NC 26
0.0 0.0
24 NC NC 25
0.0 0.0
GND_B
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
9 – 13
MAIN12 (EXBUS)
J TO MAIN8(UCOM)
L_R
TEMP2
TO MAIN15(POWER1) ROMSEL0
D3.3V
DET_PNL12V
TO MAIN16(POWER2)
TO MAIN9(CPU)
LVDS_SEL
I
SHIP_EN
PNL_EN
TO MAIN9(CPU) TO MAIN11(EPROM)
N_POCE0
N_POCE0
N_POCE1 N_POCE1
N_POCE1 N_POCE1
N_POOE N_POOE
N_POOE N_POOE
60 59
PDD0 PDD0
PDD0 PDD0
H PDD1 PDD1
58 57
PDD1 PDD1
PDD2 PDD2 56 55
PDD2 PDD2
PDD3 PDD3 54 53
PDD3 PDD3
PDD4 PDD4
PDD4 PDD4 52 51
PDD5 PDD5
PDD5 PDD5 DET_PNL12V
50 49
PDD6 PDD6
PDD6 PDD6
PDD7 PDD7
48 47
PDD7 PDD7
G PAALE PAALE 46 45
PAALE PAALE
PACLE PACLE 44 43
PACLE PACLE
N_PARB N_PARB
N_PARB N_PARB 42 PNL_EN 41
N_POWE R9302 N_POWE
N_POWE N_POWE
3.3K 40 39
CZ
38 SHIP_EN 37
OPWM2
R9326
1K 36 35
CZ
34 LVDS_SEL 33
F
R9305 32 31
4.7K
CZ ROMSEL0
30 29
TO MAIN8(UCOM) 28 27
N_SRESET
26 TEMP2 25
TO MAIN9(CPU)
SMPOWHOLD 24 23
N_CPU_RST 22 L_R 21
E R9308
4.7K C9301
CZ 0.1u
10V
20 19
TO MAIN1(TUNER) 18 17
IC9301 16 15
AHC1G08W
TO MAIN19(HOTEL) D9304 14 13
GND
N_CPU_RST 1PS184
4
3.2 12 11
1
2.8 10 9
D 3
2
0.0
R9301
2
MAIN UNIT 12/16 8 7
Vcc
47K 5
5
6
CZ DUNTKE833WE03
4 3
R9319 (PWBXE833WJ)
4.7K CZ 2 1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
9 – 14
MAIN13 (CONN)
J
TO MAIN15(POWER1)
D3.3V MAIN UNIT 13/16
TO MAIN16(POWER2)
DUNTKE833WE03
BU3.3V
5V
(PWBXE833WJ)
BU5V
I
IC9001
TC7W00U
TO MAIN8(UCOM)
IRPASS
CZF
C9003
0.1u Z
25V 8 7 6 5
D9002
MA111G VCC
H
CZ R9023
R9002
0
10K
CZ
GND
1 2 3 4
Q9001
TO MAIN8(UCOM)
RN1102
RC
TO MAIN14(EXIF) 0 0
CPU_TXD0_UCOM
G 0
CPU_RXD0_UCOM
TO MAIN8(UCOM)
CPU_TXD0_UCOM
CPU_RXD0_UCOM SC9001
NA769WJ
FB9003
CZ
A192WJ
11
R9018
10K
R9025 R9026
4.7K 4.7K R9001 5 TO MAIN9(CPU)
100 1/10W
F CZ CZ FB9004
C9006 9 I2CEXT
RHEX TVN A042WJ
0.1u
NC
D9007 4
CYB
EXA532WJ
7.5V R9020 8 TO MAIN11(EPROM)
100 1/10W FB9001
3 I2CEXT
TVN A042WJ
7
1 SELECT Vcc 16 CZB
C9008 2 SCL0
C9010
0.1u R9021 FB9002
0.1u K 100
NC
CYB A042WJ 6
10V 1/10W SDA0
2 1A /ST 15 NC NC TVN
NC
1
16 15 14 13 12 11 10 9 TO MAIN6(HDMI_SW2)
E 3 14 C2+ C2- NC RIN TOUT NC V- GND
10 SCL0
1B 4A
1 2 1 2
SDA0
1 2 IC9003
1 G1 Vcc 8 4 1Y 4B 13 ADM3101E TO MAIN7(PANEL)
3 4 SCL0
A1 C1- C1+ NC ROUT TIN NC V+ VCC
2 G2 7 3
C9004 3
NC
NC
CZB 5 6 SDA0
0.1u 12
NC
5 2A 4Y 1 2 3 4 5 6 7 8
K 10V CZ CZ
3 Y2 Y1 6 D9001 D9005 R9027 R9028
7 8 NC NC MAZ9120H
MAZ9120H 4.7K 4.7K
R9008 R9009 GND
4 A2 5
4.7K 4.7K 6 2B 3A 11 R9013 C9007 TO MAIN3(AMP_IF)
C9009
CZ CZ 4.7K 0.1u
CG1JF 0.1u *R9003 *R9007
CYB 10K 10K SCL0
CYB
D IC9002 7 2Y 3B 10 CZ CZ
TO MAIN9(CPU) 7WH126FU SDA0
CPU_UARXD0_RS
BUFFER
C9002 TO MAIN1(TUNER)
0.1u
NC
CPU_UATXD0_RS 8 GND 3Y 9
10V TUN_SCL
CPU_UARXD2_UCOM
TUN_SDA
CPU_UATXD2_UCOM
IC9004
LCX157FT
CZ
CZ
GND_B
C TO MAIN8(UCOM)
R9010 R9011
N_SRESET 1.8K 1.8K
TO MAIN11(EPROM)
SCL1
SDA1
TO MAIN9(CPU) TO MAIN19(HOTEL)
SCL1
TUN_SCL
TUN_SDA SDA1
B
TO MAIN7(PANEL)
SCL1
SCL0
SDA1
SDA0
TO MAIN5(HDMI_SW1)
SCL1
SDA1
SCL1
SDA1 TO MAIN6(HDMI_SW2)
A
SCL1
SDA1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
9 – 15
MAIN14 (EXIF)
J
TO MAIN16(POWER2)
MAIN UNIT 14/16
DUNTKE833WE03
SC9201
(PWBXE833WJ)
WA715WJQZ
I
TO MAIN8(UCOM)
PNL_DET0 1
PNL_DET1 3
4
H
PNL_DET2 5
PNL_DET3 7
PNL_DET4 9
G
10
TO MAIN15(POWER1)
TO MAIN9(CPU)
SC9202
CPU_TCK
WA715WJQZ CPU_TCK
CPU_TMS
CPU_TMS
TO MAIN8(UCOM) CPU_TDI
CPU_TDI
MODEL_A0 1 CPU_TDO
E CPU_TDO
MODEL_A1 3
MODEL_A2 5
6 TO MAIN12(EXBUS)
D N_DBG_RST
N_DBG_RST
MODEL_A3 7
MODEL_A4 9
10 TO MAIN13(CONN)
CPU_RXD0_UCOM
C CPU_RXD0_UCOM
CPU_TXD0_UCOM
CPU_TXD0_UCOM
GND_B
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
9 – 16
MAIN15 (POWER1)
J R9619 R9622 TO MAIN1(TUNER)
MAIN UNIT 15/16 4.7K 10K F
D1.8V
C9601 R9623
C9627 27K F
DUNTKE833WE03 0.01u 25V
4700P
R9624
D3.3V
25V
C9626
4.7K
(PWBXE833WJ) CZB
CZB
0.80
4.7u 10V
KZA067WJ TO MAIN18(LAN)
NC A3.3V 350mA
8 7 6 5 D3.3V
L9604
10uH PA897WJ
EN
FB
COMP
SS
C9632
SW
MM3443DF
BS
Vin
F
CZB 10u D3.3V
C9602 10V
0.796 R9611 R9610 0.1u 1 2 3 4
47K F 6.8K 25V KZA616WJQZ CE Sub Vin
8 7 6 5 CYB TO MAIN8(UCOM)
15V(8.5V 16V) R9606
10u
C9631
10V 5 6 7 D3.3V
EN
FB
39
COMP
SS
KZA616WJQZ
H IC9602 CZ
R9630 R9631 C9605
C9628 1u 10V
4.7u
D9604 1 1/2W 1 1/2W TO MAIN3(AMP IF)
LV5893M 10V
D1FS4A
TO MAIN16(POWER2) KZA067WJ
VHD
TWF TWF KZA520WJQZ D3.3V
GND
SW
BS
Vin
UR13V
CYB TO MAIN2(A_TERM)
C9624 1 2 3 4
0.1u D3.3V
5V 25V 5.1V 1000mA R9609
L9601 +USB 500mA TO MAIN11(EPROM)
15uH 4.7K
C9608
PA898WJ 0.01u 25V CZB C9615
R9614 D3.3V
OV_VLT 4700P
C9609 10K
G R9633 CZB 1.9A,77m C9619 25V
F 1.80V 900mA TO MAIN12(EXBUS)
39 2200P 10u CZB
C9618 10V
10u 0.796 R9616 R9617
C9629 10V KZA616WJQZ D3.3V
12K F 560
10u 16V KZA616WJQZ 8 7 6 5
KZA510WJPZ R9615 D9601
D1FS4A TO MAIN13(CONN)
EN
4.7
FB
COMP
SS
VHD
IC9603 D3.3V
LV5893M TO MAIN19(HOTEL)
GND
SW
D3.3V
BS
Vin
F Q9602 C9612
D9602 RT1N141U 0.1u TO MAIN14(EXIF)
25V 1 2 3 4
EXA523WJ VS CYB CIL
5.6V L9603 D3.3V
10uH C9623
GND_B D9603 R9629 10u 10V
PA897WJ
MA111G 39 KZA616WJQZ
VHD
CZB C9635 2.5A,47m D9607
TO MAIN5(HDMI_SW1)
CZ
2200P
C9616 EXA507WJ
10u D3.3V
R9608 3.2V
C9614 10V
10u 16V KZA616WJQZ
E 4.7K D9606
C9625 TO MAIN17(SP_IF)
CZ KZA510WJPZ R9634 D1FS4A 10u 10V
4.7 VHD KZA616WJQZ D3.3V
TO MAIN10(DDR)
D9609
C9636 MA111G D3.3V
470P CZB VHD
D1.8V
R9607 D9605
470 J 1PS226
D
R9603
2.7K F
Q9603 2 TO MAIN9(CPU)
KTC3875SG
1
10K F 10K F
RN1902
1
EN
SS
FB
COMP
GND
IC9601
2
6 5 4 MP2301E A1.25V
ON N.C
4
3
C9630
GND
C9610 4.7u
SW
BS
IN
0.1u
25V CYB C9617 6.3V
L9602 1u 10V
1 2 3 4 KZA403WJPZ
4.5uH KZA520WJQZ
PA895WJ 1.05V 40mV 1.6A
B 1 2 3
R9620
3.5A,30m
10 CZ
C9611
R9604 C9622
1.8K J 1000P 10u D1.1V 2000mA
C9613 CZB 10V
10u 16V
KZA616WJQZ
KZA510WJPZ R9621
4.7
C9620
A 22u 6.3V C9621
KZA385WJ 22u 6.3V
KZA385WJ
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
9 – 17
MAIN16 (POWER2)
J
TO MAIN2(A_TERM)
A5V
IC9703
TCR5SB33 TO MAIN1(TUNER)
P9701 R9706
NA181WJ 15 R9701 A5V
CZ R9702
VIn Vout
I
5
1
10K 56K
PD To Power Unit CZ CZ
FB9702 A8V
GND
2
A375WJQZ
UR13V 1 ON N.C
FB9703
4
3
5V
CZ TO MAIN14(EXIF)
*FB9701 R9740
F A074WJ 27K BU3.3V
GND_B
CZ TO MAIN7(PANEL)
TO MAIN7(PANEL) R9741
47K
5V
TO MAIN9(CPU)
TO MAIN4(AMP) A8V
UR13V
E 5V
TO MAIN15(POWER1)
BU3.3V
UR13V
OV_VLT
TO MAIN12(EXBUS)
5V
BU3.3V
TO MAIN3(AMP_IF) TO MAIN13(CONN)
UR13V 6 5 4 BU3.3V
D
AC_DET BU5V
R9738
TO MAIN9(CPU) 100K 5V
CZ
PNL_ON
1 2 3 Q9702
C9709 TO MAIN20(HT_UCOM)
RN4982 0.01u RN4982
R9739
25V D9702 5V
33K Q9701
R9736
3
CZ F MA111G
TO MAIN8(UCOM) 10K J
VHD
C
4
CZ TO MAIN11(EPROM)
BU3.3V
R9705 5V
2
5
AC_DET 1K
CZ VHD
D9701 R9704
DET_15V TO MAIN8(UCOM)
1
4.7K J
MA111G
CZ
DET_5V 5V
6
VHD
D9703 MA111G
SMPOW
D9713
B
1PS184 C9711
TO MAIN12(EXBUS) 1u 10V
KZA520WJQZ
EXT_SMPOWHOLD 1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
9 – 18
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
9 – 19
9 – 20
PARTS GUIDE
No. S37X3LC46E77U
Note:
The reference numbers on the PWB
are arranged in alphabetical order.
CONTENTS
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
2
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
3
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
4
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
5
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
6
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
7
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
8
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
9
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
10
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
11
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
12
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
13
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
14
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
15
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
[6] CABINET AND MECHANICAL PARTS (LC-46E77U)
34
27 38
1-1
1-6 35
1-3 1-6
1-5 38
1-3-1
1-3-2 33
R/C, LED Unit
4-1
4-2 42
1-2-1 1-4
2-1 8
1-2-2
6
KEY Unit
4
1
31
POWER Unit 1-2
25 41
39
30
2 40
11 26
R 2-2
17
9 41
22 29 R 18
28 20 41
41 17
41 37
9 18 41
21
23 16
24 18
32
13 43
12 MAIN Unit
17 3-2
3-1
14 19 3
X5
㧽 41
10
41 5
15
5-3
15
36 㧽
5-1
5-2
16
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
17
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
[7] LCD MODULE Assembly (LC-46E77U)
11
15
1
21
21 25
12
19
4 16
20
20
5 17
18
7
3
24
13
6
14
22
10
22
2
23
18
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
19
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
[8] CABINET AND MECHANICAL PARTS (LC-52E77U)
40
LCD Module Assembly 26
27
1-1 33
28
41
1-6
1-3 1-6
1-5
1-3-1 39
1-3-2
R/C, LED Unit
45
W
1-2-1 1-4 8
6
1-2-2
1-2 4-1
W 4-2
37 19
45 47 44
46 KEY Unit 2
31 4
46 㧿 9
11 46
9 45
36 2-2
19
32
47
R 13
13 2-1
21
17
POWER Unit 47 35 R 22
㨀
13 24 46
45
S 12 34 46 21
43
47 45 16 46
㧽 22 25
㨂 30
14 29 20
18 38
22 48
45
MAIN Unit 3-2
18 47 21 3-1
㨀 X5 3
㨁 23
17
㨂 46
10 46
5-3
15
㨁
㧽
16 5-1
5-2
42
20
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
21
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
[9] LCD MODULE Assembly (LC-52E77U)
17
18
11
20
1
20
15
25
21
21 19
12
4 16
7
3
24
13
6
14
22
10
22
2
23
22
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
X1 X2 X3 X4 X5 X6
Remote control unit "AAA" size battery AC cord Cable clamp Stand unit Operation manual
(x 1) (x 2) (x 1) (x 1) (x 1) (x 1)
23
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
[11] PACKING PARTS (NOT REPLACEMENT ITEM
X6
S6 X7
X2 X8
X4 X9 S5
X1
S4
X3
S4
S4
S3
X5
S4
S4
S4
S2
S1
S8
S7
S9
24
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
25
Downloaded from www.Manualslib.com manuals search engine
LC-46/52E77U
SHARP CORPORATION
AV Systems Group
Mar. 2009 TQ2726-S CS Promotion Center
SH. KY Yaita, Tochigi, 329-2193, Japan