You are on page 1of 3

U S N

10ME82
GHOUSIA COLLEGE OF ENGINEERING, RAMANAGARAM-562159
DEPARTMENT OF MECHANICAL ENGINEERING
3RD Internal Assessment-May 2018
VIII SEM, A & B
Control Engineering DATE: 14-05-2018
Time: 1 hr. Max marks: 25
Note: Answer Any “One Full “Questions, Assume missing data suitable.

1. Sketch the root locus Plot for G(s) H(S) =K/ S(S+2) (S+4) (S+6) (25 Marks)
2. Sketch the root locus Plot for G(s) H(S) =K(S+1)/ S(S-1) (S2+4S+16) (25 Marks)
3. a. Explain the need for system compensation .List the type of compensator? (12 ½ Marks)
b. Explain Lead and Lag Compensator. (12 ½ Marks)

Staff Incharge HOD

U S N
10ME82
GHOUSIA COLLEGE OF ENGINEERING, RAMANAGARAM-562159
DEPARTMENT OF MECHANICAL ENGINEERING
3RD Internal Assessment-May 2018
VIII SEM, A & B
Control Engineering DATE: 14-05-2018
Time: 1 hr. Max marks: 25
Note: Answer Any “One Full “Questions, Assume missing data suitable.

1. Sketch the root locus Plot for G(s) H(S) =K/ S(S+2) (S+4) (S+6) (25 Marks)
2. Sketch the root locus Plot for G(s) H(S) =K(S+1)/ S(S-1) (S2+4S+16) (25 Marks)
3. a. Explain the need for system compensation .List the type of compensator? (12 ½ Marks)
b. Explain Lead and Lag Compensator. (12 ½ Marks)

Staff Incharge HOD


b). Determine the required thickness (h) of a machine element loaded as shown in figure. The
maximum stress as the element is not to exceed 100 Mpa.(61/2Marks)

2. a). Explain Engineering Materials and their Mechanical properties.(6 Marks)


b). A machine member of diameter 60mm, in the form of cantilever and 300mm long, carries
an axial load of 18kN and a traverse load of 3kN at its free end. Determine the maximum
and minimum principal stresses and maximum shear stresses induced in the member at
critical points A and B.(6 1/2Marks)
F2 = 3000 N

F1 = 18000 N

A
B

3. a). Explain Material selection in Mechanical Engineering Design.(6 Marks)


b). A machine member of dia 60mm is subjected to a transverse load of 3 kN and a twisting
moment of 1.2 kNM as shown in fig. Determine the principal stress and shear stress at the
critical points.(6 1/2Marks)
3 kN

1.2 kNM

A
B

Staff InchargeHOD

U S N CBCS
15ME34
GHOUSIA COLLEGE OF ENGINEERING, RAMANAGARAM-562159
DEPARTMENT OF MECHANICAL ENGINEERING
IstInternal Assessment-Sept 2017
III SEM, A & B
MECHANIC’S OF MATERIALS DATE 14-09-2017
Time: 1 hr. Max marks:25
Note: Answer Any “Two Full” Questions, Assume missing data suitable.
1. a). Derive an expression for deformation in Tapered bar (Circular C/S).(6Marks)

b). A tensile test was conducted on Mild Steel bar .The following data was obtained from the
test .dia of steel bar =16mm,guage length of bar =80mm,load at proportionality
limit=72KN.Extension at a load of 60KN=0.115mm,load at failure =80KN,Dia at failure
=12mm,final guage length of bar=104mm.(6 1/2Marks)
Determine:-Youngs Modulus, proportionality limit, true breaking stress, safe stress, percentage
elongation in length, percentage reduction in area.
2. a). Explain the mechanical properties of Engineering materials. (6Marks)
b). A round stepped bar is subjected to an axial load of 30KN ,Dia and length of first portion
are 40mm and 200mm respectively,and those of second portions are 20mm and 100mm
respectively.Determine change in deformation when uniform bar of same volume and
length asthat of stepped bar bar is subjecyed to 30KN.Take E=200GPa .(6 1/2Marks)
3. a). Explain with an example Principle of Super-position.(6Marks)
b). A prismatic bar hinged at both ends is loaded as shown in figure .Find the support and
reactions and also calculate deformation in individual setion,take E=105GPa,and diameter
of bar as 30mm.(6 1/2Marks)

Staff InchargeHOD

You might also like