Professional Documents
Culture Documents
8 Expansion joint
Exposed Expansion joint (For water tightness)
WATERPROOFING & EXPANSION JOINT SYSTEMS BOQ
Products Quantity Unit Rate / Unit
1.30
BOQ
Item Description
Basement Raft / grade slab / Footing / lift pit /Retaining wall Waterproofing
Waterproofing : Pre applied pressure sensitive HDPE membrane
Providing and Installation of Fosroc Membrane HDPE-P It consists of unique HDPE membrane topped
with pressure sensitive adhesive which allows poured concrete to bond fully with the membrane shall
be supplied with one self-adhesive selvedge to provide sealed laps and comply with British Standard
8102 2009 - Code of practice for “Protection of Structures Against Water from the Ground” grades 1, 2
and 3 & British Standard 8102:2009 - code of practice for ‘Protection of Structures against Water from
the Ground’.Tensile strength, Elongation : 500% ,Puncture resistance - 950N, film : 27 MPa (ASTM
D412), Peel Adhesion to concrete : 880 N/m (ASTM D903 Modified) Resistance to hydrostatic head : >
70 mtr (ASTM D751-06(2011) and complete.Cost includes supply, mixing, application, labour, surface
preparation, etc. Power, water, storage of material shall be provided free of cost and rate excluding of
Taxes as applicable.
Termination : The membrane application shall be terminated at 300mm above the ground level by
placing a termination aluminium bar. The terminated area shall be sealed and levelled with Nitomortar
FC finish.
Unit Rate Quantity Amount
Sqm
BOQ
Item No
2.00
2.01
2.02
2.10
2.11
2.30
2.31
2.40
2.41
2.50
2.51
2.60
2.61
2.70
2.71
2.80
2.81
BOQ
Item Description
UG Sump
Swellable Waterbars for Construction Joint / pour joint / Starter joint - Supercast SW 20
Rmt
Rmt
Rmt
points
Sqm
Sqm
Sqm
Sqm
BOQ
Item No Item Description
Swellable Waterbars for Construction Joint / pour joint / Starter joint - Supercast
3.00
SW 20
Providing and applying Supercast SW 20 & Supercast SW X - water swellable-basic
polymer-hydrophilic waterstop at all construction joints, the swellable water bar shall
3.01 have unrestrained volumetric expansion up to 300%, Shore A hardness of 25 to 35,
Hydrostatic pressure resistance of 100 meters. The swellable water bar shall be fixed
to the concrete using a gun grade hydrophilic adhesive-SWX. following strictly the
instruction as per manufacture
3.10 STP Waterproofing & Protection System
3.11 Treating the Construction Joints :
Chase opening the Construction Joints by providing “ V ” groove, removing the dust and clean
the designated area following by providing chemical injection treatment in the form of pressure
grouting to the cold joint by injecting cement slurry mixed with grout admixture Cebex 100 @
225 gms.per bag of cement, in the required consistency through the pre fixed PVC nozzles in
3.12 the 18 mm dia holes, fixing of PVC nozzles with Renderoc Plug and final cutting the projected
nozzles and sealing off the PVC nozzles after the injection operation is over with Renderoc
plug, nonshrink rapid setting mortar compound, finishing, curing etc. as per manufacturers
specification and as directed.
3.20 Coving:
Providing and Appling at the junction of slab and vertical offsets with Cement Mortar 1:4 and
3.21 admixed with Nitobond SBR at dosage of 3L per bag of Cement at a size of 75 mm x 75 mm.
(Cement & Sand shall be supplied free of cost at the point of execution)
3.30 Bore Packing:
Preparing the inside surface of core and PVC by roughening using suitable file to get better
adhesion prior to packing works. Cleaning the surface by wire brushing followed water jet to
remove any laitance or loose flaky particles. Providing necessary formwork for packing the bore
using suitable arrangement (depending upon site conditions). Applying a coat of styrene-
butadiene based polymer coating using Nitobond SBR to enhance adhesion between the
packing material and other surfaces Packing the gap using non-shrink cement polymer based
3.31 grout using Conbextra GPi upto the surface of the bore whilst the Nitobond SBR is in tacky
state. The above analysis is based on assumption for 150mm diameter core with 110mm
diameter PVC for 5” thick slab only. Typical Properties Compressive strength at 28day as per
BS 1881 45N/mm2, completely as per the manufacturer’s Instruction.
Rmt
Rmt
Rmt
Nos
Sqm
Sqm
Sqm
Sqm
BOQ
Item No
4.00
4.01
4.10
4.11
4.20
4.21
4.30
4.31
4.40
4.41
4.42
4.50
4.51
4.60
4.61
4.62
4.70
4.71
4.80
4.81
4.90
4.91
4.92
BOQ
Item Description
Podium Waterproofing: Landscape, Water Bodies, Swimmingpools etc
Surface Preparation: Remove all surface laitance and contamination free from loose aggregate or other sharp
fairly smooth finish by wire brush and grinding method and surface shall be DRY for application.
Treating the Construction Joints :
Chase opening the Construction Joints by providing “ V ” groove, removing the dust and clean the designated
providing chemical injection treatment in the form of pressure grouting to the cold joint by injecting cement slurry
admixture Cebex 100 @ 225 gms.per bag of cement, in the required consistency through the pre fixed PVC
mm dia holes, fixing of PVC nozzles with Renderoc Plug and final cutting the projected nozzles and sealing off
after the injection operation is over with Renderoc plug, nonshrink rapid setting mortar compound, finishing, c
manufacturers specification and as directed.
Coving:
Providing and Appling at the junction of slab and vertical offsets with Cement Mortar 1:4 and admixed with N
dosage of 3L per bag of Cement at a size of 75 mm x 75 mm.(Cement & Sand shall be supplied free of co
execution)
Bore Packing:
Preparing the inside surface of core and PVC by roughening using suitable file to get better adhesion prior t
Cleaning the surface by wire brushing followed water jet to remove any laitance or loose flaky particles. Pro
formwork for packing the bore using suitable arrangement (depending upon site conditions). Applying a
butadiene based polymer coating using Nitobond SBR to enhance adhesion between the packing material an
Packing the gap using non-shrink cement polymer based grout using Conbextra GPi upto the surface of th
Nitobond SBR is in tacky state. The above analysis is based on assumption for 150mm diameter core with 110m
for 5” thick slab only. Typical Properties Compressive strength at 28day as per BS 1881 45N/mm2, comp
manufacturer’s Instruction.
Protection Layer( Horizontal) : Providing, batching, mixing, transporting through transit mixers, pumping and
Screed Concrete of M20 grade at all levels and heights specified below using ordinary Portland cement o
approved manufacturer, river sand, 12mm and down size coarse aggregates, Integral Waterproofing admixtur
approved by Consultants including all leads and lifts, pumping using line pump or boom placer, vibrating/ comp
directed at all heights and depths as instructed. to smooth finish and impression marking 300 x 300 Squar
/thread-markings. Treatment to continue along the vertical surface for 300mm height in shape of round wata,
Contractor scope
System: Providing and applying Nitoproof 600 Standard a single component pitch modified polyurethane at 1.3m
coats, cures by reaction with atmospheric moisture to give a tough elastomeric waterproof membrane, Nitoproof
viscosity grade (approximately 600 poise) and has a 620% of elongation, Extensibility after heat aging (
-extended to 6.4mm without cracking): No cracking or tearing, Service temperature (continuous ambient): -40
supplied in a single grade to meet all site application methods and requirements. Shall be squeezee applicatio
1.3mm. Application and methods shall be as per the Instruction of Fosroc Specification.
Protection Layer( Horizontal) : Providing, batching, mixing, transporting through transit mixers, pumping and
Screed Concrete of M20 grade at all levels and heights specified below using ordinary Portland cement o
approved manufacturer, river sand, 12mm and down size coarse aggregates, integral waterproofing Admixture
125ml admixtures approved by Consultants including all leads and lifts, pumping using line pump or boom
compaction, curing as directed at all heights and depths as instructed. to smooth finish and impression mark
continue along the vertical surface for 300mm height in shape of round wata, curing etc. *Civil Contractor scope
Unit Rate Quantity Amount
Rmt
Rmt
Nos
Rmt
Rmt
Nos
Sqm
Cum
BOQ
Item No
5.00
5.01
5.02
5.10
5.11
5.20
5.21
5.30
5.31
5.40
5.41
5.50
5.51
BOQ
Item Description
Sunken slab / Balcony / wet area / kitchen utility area
Treating the Construction Joints :
Chase opening the Construction Joints by providing “ V ” groove, removing the dust and clean the
designated area following by providing chemical injection treatment in the form of pressure grouting to
the cold joint by injecting cement slurry mixed with grout admixture Cebex 100 @ 225 gms. per bag of
cement, in the required consistency through the pre fixed PVC nozzles in the 18 mm dia holes, fixing of
PVC nozzles with Renderoc Plug and final cutting the projected nozzles and sealing off the PVC
nozzles after the injection operation is over with Renderoc plug, nonshrink rapid setting mortar
compound, finishing, curing etc. as per manufacturers specification and as directed.
Coving:
Providing and Appling at the junction of slab and vertical offsets with Cement Mortar 1:4 and admixed
with Nitobond SBR at dosage of 3L per bag of Cement at a size of 75 mm x 75 mm.(Cement & Sand
shall be supplied free of cost at the point of execution)
Bore Packing:
Preparing the inside surface of core and PVC by roughening using suitable file to get better adhesion
prior to packing works. Cleaning the surface by wire brushing followed water jet to remove any laitance
or loose flaky particles. Providing necessary formwork for packing the bore using suitable arrangement
(depending upon site conditions). Applying a coat of styrene- butadiene based polymer coating using
Nitobond SBR to enhance adhesion between the packing material and other surfaces Packing the
gap using non-shrink cement polymer based grout using Conbextra GPi upto the surface of the bore
whilst the Nitobond SBR is in tacky state. The above analysis is based on assumption for 150mm
diameter core with 110mm diameter PVC for 5” thick slab only. Typical Properties Compressive strength
at 28day as per BS 1881 45N/mm2, completely as per the manufacturer’s Instruction.
Protective layer(Horizontal ) :
Laying M20 grade screed concrete to required slope admix with integral waterproofing compound
Conplast WL of FOSROC make or Equivalent at the dosage of 125ml/bag of cement over
waterproofing layer to a minimum thickness of 50mm as per site requirement, cost for labour charge.
Rmt
Rmt
Rmt
points
Sqm
Sqm
BOQ
Item No
6.00
6.01
6.10
6.11
6.20
6.21
6.30
6.31
6.40
6.41
6.50
6.51
6.52
6.53
6.60
6.61
BOQ
Item Description
Terrace Waterproofing
Surface Preparation: Remove all surface laitance and contamination free from loose aggregate or
other sharp protrusions with fairly smooth finish by wire brush and grinding method and surface shall
be DRY for application.
Treating the Construction Joints :
Chase opening the Construction Joints by providing “ V ” groove, removing the dust and clean the
designated area following by providing chemical injection treatment in the form of pressure grouting to
the cold joint by injecting cement slurry mixed with grout admixture Cebex 100 @ 225 gms.per bag of
cement, in the required consistency through the pre fixed PVC nozzles in the 18 mm dia holes, fixing
of PVC nozzles with Renderoc Plug and final cutting the projected nozzles and sealing off the PVC
nozzles after the injection operation is over with Renderoc plug, nonshrink rapid setting mortar
compound, finishing, curing etc. as per manufacturers specification and as directed.
Coving:
Providing and Appling at the junction of slab and vertical offsets with Cement Mortar 1:4 and admixed
with Nitobond SBR at dosage of 3L per bag of Cement at a size of 75 mm x 75 mm.(Cement & Sand
shall be supplied free of cost at the point of execution)
Bore Packing:
Preparing the inside surface of core and PVC by roughening using suitable file to get better adhesion
prior to packing works. Cleaning the surface by wire brushing followed water jet to remove any
laitance or loose flaky particles. Providing necessary formwork for packing the bore using suitable
arrangement (depending upon site conditions). Applying a coat of styrene- butadiene based polymer
coating using Nitobond SBR to enhance adhesion between the packing material and other surfaces
Packing the gap using non-shrink cement polymer based grout using Conbextra GPi upto the surface
of the bore whilst the Nitobond SBR is in tacky state. The above analysis is based on assumption for
150mm diameter core with 110mm diameter PVC for 5” thick slab only. Typical Properties
Compressive strength at 28day as per BS 1881 45N/mm2, completely as per the manufacturer’s
Instruction.
Waterproofing System
Priming: Priming is not normally required on good quality concrete substrates. However, absorbent
surfaces such as porous concrete, sand/cement and cement boards will require sealing to prevent
absorption of Nitoproof 600 standard. This should be done using a 1:1 mixture of Nitoproof 600
standard and Nitoflor Sol. All metal and PVC surfaces should be cleaned and abraded before priming.
System: Providing and applying Nitoproof 600 Standard a single component pitch modified
polyurethane in two coats forming totally 1.3mm thickness cures by reaction with atmospheric
moisture to give a tough elastomeric waterproof membrane, Nitoproof 600 Standard is a medium
viscosity grade (approximately 600 poise) and has a 450% of elongation, Extensibility after heat aging
(min. requirement -extended to 6.4mm without cracking): No cracking or tearing, Service temperature
(continuous ambient): -40°C to 70°C. It is supplied in a single grade to meet all site application
methods and requirements. Shall be squeeze application for thickness of 1.3mm. Work shall be
executed as by authorised Applicator .Application and methods shall be as per the Instruction of
Fosroc Specification
Protection Layer
Providing a Geotext fabric of 150GSM over the cured waterproofing membrane before going for a
Protection Screed.
Protection Layer (Horizontal) : Providing and laying min 50mm thick screed concrete of M20 grade
with optional to incorporating Polypropylene fibre as per manufacturer’s dosage and admixed with
water proofing compound Conplast WL (Integral waterproofing compound confirming to IS 2645) at a
dosage of 125 ml / bag of cement. Providing Grove Cutting at 4.0m C/C the joint size shall be 4mm x
10mm which shall be filled with Nitoseal PU all complete as per manufacture's specifications and
instruction and as directed. *Civil Contractor scope
Protective Layer (Vertical): Providing and applying plastering with CM 1:4 mixed with Conplast WL at
the dosage of 125ml/bag of cement over waterproofing system to a minimum thickness of 18mm as
per site requirement. *Civil Contractor scope
Parapet wall weatherproof Coating: Nitocote Wall Guard
Providing and applying Nitocote Wall guard Elastomeric & Decorative acrylic waterproofing coating for
exterior walls on the external vertical surfaces of Over Head water tank(available in Different RIL
shades). Applied at 110 micron dry film thickness in two coats as per manufacturer specification.
Coating shall be UV resistant, breathable & flexible having minimum 100% elongation when applied at
110 micron DFT. Nitocote Wall Guard is water based polymer coating composed of high quality acrylic
polymer, with weather resistant pigments, properly selected & graded fine fillers. It is used as a
waterproofing & decorative coating for protection of exterior walls of the buildings from heavy wind
driven rain.
Unit Rate Quantity Amount
Rmt
Rmt
Nos
Sqm
Sqm
Sqm
Sqm
BOQ
Item No Item Description
7.00 OHT Waterproofing
7.01 Treating the Construction Joints :
Chase opening the Construction Joints by providing “ V ” groove, removing the dust and
clean the designated area following by providing chemical injection treatment in the form of
pressure grouting to the cold joint by injecting cement slurry mixed with grout admixture
Cebex 100 @ 225 gms.per bag of cement, in the required consistency through the pre fixed
7.02 PVC nozzles in the 18 mm dia holes, fixing of PVC nozzles with Renderoc Plug and final
cutting the projected nozzles and sealing off the PVC nozzles after the injection operation is
over with Renderoc plug, nonshrink rapid setting mortar compound, finishing, curing etc. as
per manufacturers specification and as directed.
7.10 Coving:
Providing and Appling at the junction of slab and vertical offsets with Cement Mortar 1:4 and
7.11 admixed with Nitobond SBR at dosage of 3L per bag of Cement at a size of 75 mm x 75
mm.(Cement & Sand shall be supplied free of cost at the point of execution)
7.20 Bore Packing:
Preparing the inside surface of core and PVC by roughening using suitable file to get better
adhesion prior to packing works. Cleaning the surface by wire brushing followed water jet to
remove any laitance or loose flaky particles. Providing necessary formwork for packing the
bore using suitable arrangement (depending upon site conditions). Applying a coat of
styrene- butadiene based polymer coating using Nitobond SBR to enhance adhesion
between the packing material and other surfaces Packing the gap using non-shrink cement
7.21 polymer based grout using Conbextra GPi upto the surface of the bore whilst the Nitobond
SBR is in tacky state. The above analysis is based on assumption for 150mm diameter core
with 110mm diameter PVC for 5” thick slab only. Typical Properties Compressive strength at
28day as per BS 1881 45N/mm2, completely as per the manufacturer’s Instruction.
Rmt
Rmt
Nos
Sqm
Sqm
Sqm
Sqm
BOQ
Item No
8.00
8.01
8.10
8.11
8.20
8.21
8.30
8.31
8.40
8.41
8.42
8.50
8.51
8.60
BOQ
Item Description
Providing Expansion Joint system as per the Drawing for width of 50mm x 25mm
Expansion joint FILLER BOARD
Suppling Expansion joint Filler board as per the drawing to the designated area shall be Fosroc Hydrocell XL
which shall be cross linked, non absorbent, semi rigid, cellular polyethylene with a nominal density of 60 kg/m3. It
shall have a recovery of 98% after 50% compression and a compressive strength of 0.15 N/mm2 when tested in
accordance with ASTM D3575. It shall have water absorption of less than 0.05% by volume when tested in
accordance with ASTM D3575 and be resistant to weathering and chemical attack. Chemical resistance of
Hydrocell XL an excellent resistance to acids, alkalis, oxidising agents and biological degradation The joint filler
shall have Water Byelaws Scheme approval for use in contact with potable water. cost supply of material only.
BACKER ROD
Providing and placing Backer rod of suitable Diameter using Fosroc Expancel over the existing Polyethylene filler
board .
SEALANT : Polysulphide Sealant
Priming: Highly absorbent substrate should be primed. Fosroc Primer 7E /Primer 4 - For use on concrete, stone,
brickwork, timber andunglazed ,Aluminium edges. One thin coat should be applied and allowed to dry for some
time. Shall be supplied in 0.5 liter pack,
Sealant :Suppling and laying expansion joint Sealant as per the drawing to the designated area shall be Fosroc
Thioflex 600 a two part joint sealant based on a liquid polysulphide polymer. It is supplied as a 2.5 L pack
containing a base component and curing agent in the correct proportions which, when mixed together, cure to form
a tough rubber-like material. When cured, the sealant exhibits excellent adhesion to most surfaces including
concrete, Joint shall be sealed using Fosroc Thioflex 600, two part, polysulphide sealant, manufactured by Fosroc
to BS 4254 - 1983. Joint shall be prepared and the sealant mixed and applied in accordance with the
manufacturer's current data sheet.
WATER TIGHT MEMBRANE for Exposed condition vertical & Horizontal Expansion joint
Providing and fixing Fosroc Expoband One a Hypalon membrane system shall be supplied in size of 1.0mm thick
of 200mm width which is designed to be bonded over movement joints in structures to prevent the passage of
water. that exhibits following properties Density- 1.7 approximate, Tensile Strength- 7.0 N/sqmm,Elongation at
break- 400% .It is bonded in position using Fosroc Nitomortar FC is a two component thixotropic, solvent free,
compound based on epoxy resins, graded fillers and thixotropic agents.leaving the Sealant area . Expoband ONE is
suitable in construction use. The application and finishing shall be as per Fosroc specifications.
Note : Expansion joint sealant HAS TO BE PROTECTED from in Direct Contact with Wheel where ever the
vehicular movement is possible, by providing min 3.0mm Galvanised sheet by anchoring at one side of the
Expansion joint,.
Unit Rate Quantity Amount
-
Sqm
LS
Rmt
rmt