Professional Documents
Culture Documents
Technical specification
Dry Dock
Page 1 of 6
Summary
Project DD--TANTO LANGGENG-9796353-558 TEU-Container Prepared by Tito Hanafiah - Jotun Coatings
vessel-SMI-
Customer Tanto Intim Line Approved by Tito Hanafiah Version 1
Location SAMUDERA MARINE INDONESIA Date 12/6/2018
Page 2 of 6
Technical specification
Project DD--TANTO LANGGENG-9796353-558 TEU-Container Prepared by Tito Hanafiah - Jotun Coatings
vessel-SMI-
Customer Tanto Intim Line Approved by Tito Hanafiah Version 1
Location SAMUDERA MARINE INDONESIA Date 12/6/2018
Position Flat Bottom (From bilge keel to bilge keel) Area 1755 m² No. 1
Surface Prep. Remove oil and grease with a suitable detergent followed by fresh water cleaning to remove salts and other contaminants on entire area to be
painted. Remove corrosion and loose coatings on affected areas to min. Sa 2 (ISO 8501-1). Sweep-blast remaining coatings to obtain a sound and
intact surface. Edges of remaning existing coatings should be feathered.
Product Type Area to Vol. solids Filmthickness (µm) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 23°C 35°C 40°C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAPRIME 500,ALUMINIUM RED TONED TU 40 72 150 208 15 4h 7d * * 2 h 6 d 17 15 146 172
SAFEGUARD UNIVERSAL ES,GREY FC 100 62 100 161 15 10 h 7 d * * 6 h 3 d 17 15 283 333
SEAFORCE 30 M,RED FC 100 62 100 161 15 7h * * * 6h * 7 15 283 333
Total 350
Remarks:
Page 3 of 6
Technical specification
Project DD--TANTO LANGGENG-9796353-558 TEU-Container Prepared by Tito Hanafiah - Jotun Coatings
vessel-SMI-
Customer Tanto Intim Line Approved by Tito Hanafiah Version 1
Location SAMUDERA MARINE INDONESIA Date 12/6/2018
Position Side bottom (From bilge keel to scantling draft) Area 1555 m² No. 2
Surface Prep. Remove oil and grease with a suitable detergent followed by fresh water cleaning to remove salts and other contaminants on entire area to be
painted. Remove corrosion and loose coatings on affected areas to min. Sa 2 (ISO 8501-1). Sweep-blast remaining coatings to obtain a sound and
intact surface. Edges of remaning existing coatings should be feathered.
Product Type Area to Vol. solids Filmthickness (µm) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 23°C 35°C 40°C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAPRIME 500,ALUMINIUM RED TONED TU 40 72 150 208 20 4h 7d * * 2 h 6 d 17 15 130 162
SAFEGUARD UNIVERSAL ES,GREY FC 100 62 100 161 20 10 h 7 d * * 6 h 3 d 17 15 251 314
SEAFORCE 30 M,RED FC 100 62 150 242 20 7h * * * 6h * 7 15 376 470
Total 400
Remarks:
Page 4 of 6
Technical specification
Project DD--TANTO LANGGENG-9796353-558 TEU-Container Prepared by Tito Hanafiah - Jotun Coatings
vessel-SMI-
Customer Tanto Intim Line Approved by Tito Hanafiah Version 1
Location SAMUDERA MARINE INDONESIA Date 12/6/2018
Remarks:
Page 5 of 6
* please refer to the relevant technical datasheets and AG application guide for recoating and curing conditions
NR: Not recommended for this exposure or generic type:
Unless otherwise agreed in writing, all product supplied and technical advice given by us are subject to our standard terms and conditions of sale. In the event that supplies are made and
technical advice is given by one of our associated companies or dealers, then such supplies and technical advice shall be subject to the standard terms of sale of that company, a copy of
which is available upon request. The given data must be considered as guidelines only, the figures in some columns may be rounded. Drying times and paint consumptions may vary
depending on actual conditions.
For updated information about our products please refer to our web site at www.jotun.com
Page 6 of 6