Professional Documents
Culture Documents
F-SERIES
GB150 / GB8AF / GB8F / GB9F / GB11F / GB14F
Exceptional Performance & Quality!
GB Hydraulic Breaker
OPERATING & MAINTENANCE MANUAL
& PART LIST
No. TFME1004
PREFACE
This publication should be carefully read prior to installation and operation in order to prevent any mishandling
of the breaker. We guarantee that faithful compliance of the instructions will contribute to the best operational
condition. Customers are reminded that General Breakers takes no responsibility in damage caused by failure
to follow our guidelines or failure to use genuine parts.
2. STRUCTURE 13
3. WORKING PRINCIPLE 14
5. HYDRAULIC OIL 27
1. Selection of oil 27
2. Oil contamination 27
3. Criteria of oil contamination and malfunction (General analysis) 28
4. Criteria of malfunction by hydraulic oil color (Simple discrimination by ASTM color) 28
6. TOOLS 29
1. Replacement of tool 29
2. Tool bit greasing 30
3. Guide to tool choice 31
7. OPERATION 32
1. Operation method 33
2. Proper thrust 33
3. Precautions in operation 34
4 | GB HYDRAULIC BREAKERS
4. Oil temperature 43
5. Oil leakage 43
T-SERIES
GBM60 / GBM90 / GB1T / GB2T / GB3TP
- BREAKER BODY 48
- SIDE PLATE TYPE BRACKET 51
- BOX TYPE BRACKET 53
- SIDE TYPE BRACKET 55
- UNIRAM TYPE BRACKET 57
- BACK HOE TYPE BRACKET 59
F-SERIES
GB150 / GB8AF / GB8F / GB9F / GB11F / GB14F
- BREAKER BODY 71
- SIDE PLATE TYPE BRACKET 74
- BOX TYPE BRACKET 75
- SIDE TYPE BRACKET 79
DANGER
DO NOT OPERATE THE BREAKER UNLESS THE FOLLOWING SAFETY INSTRUCTIONS HAVE
BEEN THOROUGHLY READ AND UNDERSTOOD! READ THIS MANUAL BEFORE INSTALLING,
OPERATING OR MAINTAINING THIS EQUIPMENT!
WARNING
� WHEN LEAVING THE HYDRAULIC EXCAVATOR, LOWER THE BREAKER TO THE GROUND
AND TURN THE ENGINE OFF.
� NEVER ATTACH A CABLE OR SLING TO THE BREAKER TO HOIST A LOAD. DOING SO IS
EXTREMELY DANGEROUS.
� KEEP PEOPLE AND EQUIPMENT AWAY FROM THE BREAKER DURING OPERATION.
ROCKS FLYING FROM THE BREAKER DURING OPERATION MAY CAUSE ACCIDENTS.
� EAR, EYE AND BREATHING PROTECTION MUST BE USED AT ALL TIMES WHEN
OPERATING THE BREAKER.
� DO NOT TOUCH ANY PART OF THE MACHINE WHILE THE HYDRAULIC OIL IS HOT. IT MAY
CAUSE YOUR HANDS TO BURN.
IMPORTANT
6 | GB HYDRAULIC BREAKERS
Precautions when using hydraulic breakers
ⓐ Operate the breaker in accordance with all laws and regulations which affect you, your equipment
and the worksite.
ⓑ Do not operate the breaker unless you have read the carrier equipment manual and fully understand
all safety, operation and maintenance instructions.
ⓒ Ensure that all maintenance procedures recommended in this manual are completed before using
the equipment.
ⓓ Know the limits of your equipment.
ⓔ Establish a training program for all operators to ensure safe operation.
ⓕ Do not operate the breaker unless fully trained or under the supervision of an instructor.
ⓖ Become familiar with the carrier controls before operating the carrier and the breaker.
ⓗ While learning to operate the breaker and carrier, do so at a slow pace. If necessary, set the carrier
mode selector to the slow position.
ⓘ Make sure all controls (levers and pedals) are in the neutral position before turning on the carrier’s
ignition.
ⓙ Before leaving the carrier, always lower the boom and ensure the carrier is stable. Never leave the
machine with the engine running. Always engage the parking brake.
ⓚ Do not operate the breaker at oil temperatures above 175�
F/80�
C. Operation at higher temperatures
can cause damage to the internal components of the breaker and backhoe/ excavator, and will result
in reduced breaker performance.
ⓛ Do not operate a damaged, leaking, improperly adjusted, or incompletely assembled breaker.
ⓜ Do not modify the breaker in any manner.
ⓝ Only use breaker tools manufactured by General Breakers. Use of breaker tools produced by another
manufacturer may damage the equipment and will void the warranty.
ⓞ To avoid personal injury or equipment damage, all breaker repair, maintenance and service must
only be performed by authorized and properly trained personnel.
ⓟ If you do not understand how to safely operate your breaker, contact an authorized General Breakers
Dealer for assistance.
ⓠ Keep this manual with the breaker.
ⓡ Do not operate this equipment if you are taking medication which may affect your mental judgement
or physical performance.
ⓢ Do not operate this equipment if you are under the influence of drugs or alcohol.
ⓣ Remove breaker from carrier during transport.
ⓤ Be familiar with the work area and surroundings.
DANGER STICKER
WARNING STICKER
- Shown smaller than actual size
8 | GB HYDRAULIC BREAKERS
Precautions when using hydraulic breakers
CAUTION STICKER
- Lifting point
SAFETY SYMBOLS
a. Safety symbols are to emphasize all operator,
DANGER
maintenance and repair action which, if not strictly
followed, could result in a life-threatening situation, This safety symbol may appear on
bodily injury of damage to equipment. the breaker. It is used to alert the
operator of an action that could
place him/her or others in a life
b. Always observe safety symbols. They are included
threatening situation.
for your safety and for the protection of the breaker.
WARNING
This safety symbol appears in
these instructions to identify an
action that could cause bodily
injury to the operator or other
personnel.
IMPORTANT
This safety symbol appears in
these instruction to identify an
action or condi- tion that could
result in damage to the breaker or
other equipment.
GREASING STICKER
GREASING
1.With breaker mounted on carrier, apply down pressure on tool.
2. Fill cavity with recommended grease.
3. Grease whenever tool looks dry.
4. When installing a new tool, liberally coat the upper 1/3 of the tool
with grease before inserting.
5. Failure to comply with these instruction can result in damage to the
breaker and will void the warranty.
10 | GB HYDRAULIC BREAKERS
Precautions when using hydraulic breakers
T-SERIES
GB8AT
ITEM \ MODEL UNIT GBM60 GBM90 GB1T GB2T GB3TP GB4T GB5T GB6T GB8T
(GB7T)
Impact energy joules 180 220 320 600 700 1,270 2,000 2,950 4,500 5,000
800 ~ 650 ~ 550 ~ 450 ~ 475 ~ 480 ~ 450 ~ 420 ~ 350 ~ 320 ~
Blow per minute b.p.m
1,400 1,200 1,100 1,000 950 850 780 730 680 660
lit/min 15~30 20~35 24~50 34~60 40~80 45~85 85~110 100~120 120~150 120~150
Oil flow rate
(g.p.m) (4~8) (5~9) (6~13) (9~16) (10~21) (12~22) (22~29) (26~32) (32~40) (32~40)
Side plate kg 75 86 176 324 380 613 850 1,280 1,800 1,980
Operating type (lbs) (165) (189) (387) (713) (836) (1,349) (1,870) (2,816) (3,960) (4,356)
weight
with mounting
cap Low noise kg 135 145 190 310 380 570 890 1,200 1,700 1,860
box type (lbs) (297) (319) (418) (682) (836) (1,254) (1,958) (2,640) (3,740) (4,092)
Height with tool mm 988 1,082 1,205 1,384 1,451 1,789 2,043 2,264 2,411 2,477
with low noise box type
without mounting cap
(inch) (38.9) (42.6) (47.4) (54.5) (57.1) (70.4) (80.4) (89.1) (94.9) (97.5)
0.7~2.5 1.2~3 2.5~4.5 3.5~7 5~9 6~13 10~17 15~20 18~28 20~30
ton
Weight of carrier (1,540~ (1,640~ (5,500~ (7,700~ (11,000~ (13,200~ (22,000~ (33,000~ (39,600~ (44,000~
(lbs)
5,500) 6,600) 9,900) 15,400) 19,800) 28,600) 37,400) 44,000) 61,600) 66,000)
Bucket capacity c.b.m 0.02~0.04 0.04~0.07 0.06~0.1 0.1~0.25 0.2~0.35 0.25~0.45 0.4~0.7 0.6~0.8 0.7~1.0 0.8~1.1
75~95 80~100 90~120 95~130 100~140 130~150 150~170 150~170 160~180 160~180
Operating bar
(1,102~ (1,176~ (1,323~ (1,396~ (1,470~ (1,911~ (2,205~ (2,205~ (2,352~ (2,352~
oil pressure (psi)
1,380) 1,470) 1,764) 1,911) 2,058) 2,205) 2,499) 2,499) 2,646) 2,646)
Hose / Tubing mm 13 13 13 13 13 19 19 25 25 25
size (inch) (1/2) (1/2) (1/2) (1/2) (1/2) (3/4) (3/4) (1) (1) (1)
85 dB(A) radius
m 7 7 8 10 11 12 13 14 15 16
(Box type)
F-SERIES
ITEM \ MODEL UNIT GB150 GB8AF GB8F GB9F GB11F GB14F
Blow per minute b.p.m 420~ 730 350~ 680 300 ~ 600 280 ~ 550 280 ~ 550 280 ~ 400
Hose / Tubing mm 25 25 25 25 32 32
size (inch) (1) (1) (1) (1) (1¼ ) (1¼ )
85 dB(A) radius
m 14 15 15 16 17 18
(Box type)
12 | GB HYDRAULIC BREAKERS
Structure
2 STRUCTURE
T-SERIES
TIE ROD
Tie Rod
Front head, cylinder and back head of breaker
body are tightly fixed with four tie rods.
Back Head
(Gas Chamber)
BACK HEAD
Gas charging valve is built in and the inside is
Valve charged with N2 gas.
VALVE
Cylinder Cylindrical control valve is built in the valve
housing and controls piston reciprocation.
CYLINDER
The cylinder is the heart of the breaker con-
Accumulator taining hydraulic circuit for piston reciprocation.
FRONT HEAD
The front head supports the whole breaker.
Tool Thrust ring and thrust bushing prevents shock
from the tool.
TOOL
The specially heat-treated tool is directly applied
to break rocks. It is in the form of a wedge, moil
point, blunt, cone and wide chisel appropriate to
the application. (optional)
3 WORKING PRINCIPLE
T-SERIES
The relation between the area (A1) affecting the pressure from the upper chamber of the piston and the area
(A2) affecting the pressure from the lower chamber of the piston is A1> A2 and high pressure always applies to
A2. When A1 changes from high to low pressure or vice versa, Piston C2 reciprocates. Inside of back head is
charged with the high pressure gas and gas energy stored in the upstroke of the piston C2 effectively acts on
the piston C2 during the impact.
1. POWER STROKE
When piston C2 reaches top dead center, high pressure oil
from valve high-pressure port B3 applies to upper chamber
of the piston A1 to change the piston stroke from upstroke to
impact.
At this time the relation between the area(A3) affecting the
pressure from valve high pressure changes and the
area(A4) of the valve change chamber is A4 > A3. The high
pressure always applies to A4 and valve C4 remains in the
upper position.
2. VALVE SHIFT
When cylinder low pressure port B1 is connected to cylinder
change port B2, the pressure in valve change port B4
lowers. As force acting on valve C4 is the only pressure in
valve high pressure chamber A3, valve C4 starts lowering.
During the valve lowering stroke, valve high pressure port
B3 is closed and valve low pressure port B5 is opened to
the upper chamber of the piston A1 to lower the pressure in
the upper chamber of the piston A1.
14 | GB HYDRAULIC BREAKERS
Working principle
3. IMPACT
When piston C2 reaches impact point, kinetic energy
obtained by piston C2 during the impact stroke is transmited
to the tool C3 for the impact energy required to break. At this
time, as high pressure applies only to the lower chamber of
the piston A2, piston C2 starts reversing. Further, as high
pressure applies only to the valve high pressure chamber
A3, valve C4 is remaining in the lower position.
4. UPSTROKE
When cylinder change port B2 is connected to cylinder
lower pressure port B1, high pressure oil applies to low
pressure outlet port and valve C4 start to the down position
A1 this time valve low pressure port B5 is closed and valve
high pressure B3 is opened the upper chamber of the piston
A1 to rise the pressure in the lower chamber of the piston
A1.
WARNING
IMPORTANT
THE CIRCUIT RELIEF SETTING PRESSURE IS NOT FIXED. HOWEVER, IT WILL BE ADJUSTED BY PUMP
CAPACITY.
T-SERIES
ITEM \ MODEL UNIT GBM60 GBM90 GB1T GB2T GB3TP GB4T GB5T GB6T GB8AT GB8T
Relief setting
kgf/cm2 150 150 150 160 160 180 200 200 200 200
pressure
Back pressure
kgf/cm2 14 14 14 16.3 16.3 16.3 16.3 16.3 16.3 16.3
(Max)
F-SERIES
Relief setting
kgf/cm2 210 210 210 210 210 210
pressure
Back pressure
kgf/cm2 16.3 16.3 16.3 16.3 16.3 16.3
(Max)
Since GB hydraulic breaker operates with various kinds of hydraulic construction machines, it should
be installed after our serviceman has carried out the necessary check on the base machine to utilize
its full performance.
16 | GB HYDRAULIC BREAKERS
Installation & removal of hydraulic breaker
2 3 5 7 6
1
10 11 9
4 8
WARNING
� CHARGING GAS PRESSURE CHANGES ACCORDING TO THE TOOL CONDITION. LAY DOWN THE
BREAKER AND LET THE TOOL EXTEND FULLY TO CHARGE GAS.
� STAY CLEAR OF THE TOOL WHILE CHARGING THE BREAKER WITH GAS. THE TOOL MAY BE
IMPACTED BY THE PISTON AND FORCED OUT ABRUPTLY.
� TAKE CARE WHEN THE TIE RODS ARE CHANGED OR THE BREAKER BODY IS DISASSEMBLED.
� USE SPECIAL CARE TO HANDLE AND STORE THE N2 GAS CYLINDER AS IT IS A HIGH-
PRESSURIZED CONTAINER.
� USE NITROGEN GAS ONLY.
� SEE“CONVERSION TABLE FOR CHARGING N2 GAS PRESSURE TO BACK HEAD”
(1) Remove gas valve plug (2) Insert 3-way valve with (3) If gas is insufficient, adjust to specified valve as
pressure gauge assembled shown in the previous page (Note. 2)
(Note. 1)
(4) Adjust the pressure slowly decreasing by using the (5) Tighten gas valve plug (Do not cut O-ring)
pressure gauge if gas is sufficient
NOTE
18 | GB HYDRAULIC BREAKERS
Installation & removal of hydraulic breaker
WARNING
� USE SPECIAL CARE TO HANDLE AND STORE THE N2 GAS CYLINDER AS IT IS A HIGH-
PRESSURIZED CONTAINER.
� USE NITROGEN GAS ONLY.
� SEE“CONVERSION TABLE FOR CHARGING N2 GAS PRESSURE TO ACCUMULATOR”
� STANDARD ACCUMULATOR GAS PRESSURE 57kg/cm2/808psi, AT 20℃/68℉ AMBIENT
TEMPERATURE, DO NOT OVER PRESSURIZE ACCUMULATOR.
- Be sure to use the 3-way valve assembly for charging the N2 gas.
If charging gas leaks directly from the cylinder, the diaphragm may be broken off.
- If charging for handling N2 gas to only the accumulator, make sure that the accumulator body and
cover are tightened fully.
1) Make sure the cap and valve of the 3-way valve assembly are fully tightened.
2) Remove the cap from the accumulator and tighten the charging valve fully.
3) Check if 0-rings are installed to the bushing. Remove the plug and screw in the bushing.
20 | GB HYDRAULIC BREAKERS
Installation & removal of hydraulic breaker
1) Connect the charging hose to N2 gas cylinder after screwing the bombe adapter onto adapter, nut
and installing to the N2 gas cylinder.
2) Connect the 3-way valve assembly to the charging hose after unscrewing the cap on the 3-way valve
assembly.
3) Remove the cap from the accumulator and tighten the charging valve fully.
4) Check if 0-ring are installed to the bushing. Remove the plug and screw the bushing.
5) Loosen the accumulator charging valve after checking if bushing is installed to the 3-way valve
assembly.
6) Turn the handle of the N2 gas cylinder counterclockwise slowly to charge gas.
7) Charge gas in accordance with the conversion table for charging N2 gas pressure to accumulator.
8) Turn the handle of the N2 gas cylinder clockwise to close the cock.
9) Close the accumulator charging valve.
10) Loosen the valve of the 3-way valve assembly to discharge the N2 gas remaining in the charging
hose.
11) Remove the charging hose, 3-way valve assembly and bushing and tighten the plug and cap.
kg/cm2 50 53 57 60 62
GB150~GB14F
Operation of the hydraulic breaker requires installation of hydraulic pipe lines for exclusive use of the
hydraulic breaker. As hydraulic pipe lines vary depending on base machines, our service engineer must
first check the hydraulic pressure, oil capacity, pressure loss and other conditions of the base machine
before installing hydraulic pipe lines. Use only genuine parts in case of the need for replacement as
hydraulic pipe lines (hoses, pipes and fittings) are made of materials carefully selected in consideration
of durability.
22 | GB HYDRAULIC BREAKERS
Installation & removal of hydraulic breaker
WARNING
Filter
Tank
Swing
OUT Low Pressure
Arm
Boom
Trevaling
IN High Pressure Trevaling
Bucket
X N Tank Boom
(Cable)
Hydraulic Hydraulic
Control valve for breaker pump pump
Tank
Tank Tank
Wood block
Position of the base machine for installation and
removal of the hydraulic breaker
WARNING : Do not approach tool, as rod may fly out due to the N2 gas pressure.
(3) Loosen hose plug on the breaker arm. Collect a small amount of oil flowing out at this time and put
into a container.
(4) Be careful to prevent mud or dust from entering oil hoses and pipe lines. Plug oil hoses with hose
plug and pipe lines with union caps. Bind high and low pressure hoses with a wire to prevent them
from getting muddy.
(5) To remove the breaker, pull out pins in the bucket link and arm. When leaving the breaker outdoors,
set the breaker on wood blocks and cover with sheets.
(6) When leaving the removed breaker for a long period of time
- Clean the exterior of the breaker.
- Detach tool from the front head and spray with rust preventive oil.
Bleed N2 gas from the back head before pushing piston into cylinder.
- Apply grease to each part of the breaker and then install tool again.
(7) To install the hydraulic breaker, reverse the aforementioned removal procedures. The bucket
operation easily contaminates the end part of hoses and pipe lines. The contaminated part must be
cleaned without delay. Hydraulic oil or light oil is highly recommended.
7. TRANSPORT OF BREAKER
24 | GB HYDRAULIC BREAKERS
Installation & removal of hydraulic breaker
- Uner water operation of the breaker is possible to pour air into the striking area between the piston
and the rod.
- For the sake of underwater operation, the piston adatper is supplied as a standard part.
- For the sake of underwater operation, breaker is installed the air supply kit separately.
- Underwater usage of the breaker without the underwater kit and air compressor will cause serious
damage to the hydraulic breaker.
GBM90 GB6T
GBM60 GB1T GB2T GB3TP GB4T GB5T GB150
DEPTH(m) PRESSURE(bar)
19
18 GB8F
GB8AF
17
GB8T
16 GB8AT
15 3bar
14
13
12
11
GB11F
10 2bar
GB14F
9
8
7
6
5 1bar
4
3
2
1
1 OP13007 O-RING 1
2 OPTION MALE ADAPTER 1
3 OPTION HOSE 1
4 EV14039 AIR CHECK VALVE 1
26 | GB HYDRAULIC BREAKERS
Hydraulic oil
5 HYDRAULIC OIL
1. SELECTION OF OIL
Selection of Hydraulic oil determines the efficiency of the hydraulic breaker performance. Please consult
with our service station under following conditions.
a. When used in special regions where climate is severe(e.g. extremely cold or hot weather), viscosity at
different constant ambient air temperatures.
b. When recommended brands of hydraulic oil are not available.
c. When hydraulic oils supplied for the base machine differ from the recommended one.
2. OIL CONTAMINATION
Contaminated oil results in malfunctions of the breaker as well as the base machine and causes
damage to parts. Pay special attention to oil contamination.
Contaminated oil should be changed without delay. When changing oil, thoroughly wash oil tank,
cylinder and pipes. Cleaning or replacing oil filter also requires check for oil contamination.
- Replacement of filter : after first 50 hours and every 250 hours thereafter
- Replacement of Hydraulic oil : every 1,500 hours
WARNING IMPORTANT
ANALYSIS ITEM CRITERIA CAUSES AND EFFECTS WHEN EXCEEDS THE CRITERIA
Hydraulic oil turns black as the breaker fails to display best performance. The old oil is assumed to be
contaminated when there is a visual difference between the old and new oil color and functions begin to
deteriorate when hydraulic oil turns darker than the new oil color(ASTM number) by more than two.
28 | GB HYDRAULIC BREAKERS
Tool
6 TOOL
1. REPLACEMENT OF TOOL
Rubber
Plug
Stopper Pin
Tool
NOTE
1. When replacing the tool, remove burrs and swelling with a grinder or the like.
2. Regularly check the tool pins for cracks or breakage upon replacement of tool.
CAUTION IMPORTANT
Greasing
While greasing, hammer must be upright against the
tool, to ensure that grease will penetrate between tool
and bush.
Lubricant
Grease
Manufacturer
30 | GB HYDRAULIC BREAKERS
Tool
The correct choice of the most suitable tool for a certain job is crucial not only in increasing breaker
productivity, but also for the life of the tool itself.
A B C D E
A. WEDGE
- Suitable for all kinds of digging or narrow trenching on soft/medium stratified rocks.
C. BLUNT (FLAT-END)
- Suitable for breaking blocks of up to medium hardness or to cut the size of small blocks.
D. CONE
- Universal.
E. WIDE CHISEL
7 OPERATION
WARNING
WARNING
� WHEN WORKING IN TEMPERATURE CONDITIONS OF LOWER THAN MINUS 20℃, THE HYDRAULIC
BREAKER SHOULD NOT BE PUT INTO OPERATION WHILST THE HYDRAULIC OIL IS STILL COLD.
� OPERATING THE BREAKER WITH COLD HYDRAULIC OIL MAY CAUSE THE SEALS IN THE
HYDRAULIC BREAKER TO TEAR THE DIAPHRAGM IN THE HIGH-PRESSURE ACCUMULATOR.
� OBSERVE THE MANUFACTURER’S REGULATIONS
spanner
④ Valve adjuster turning position
CAUTION
If the adjuster is turned fully clockwise, then the breaker will cease to operate.
32 | GB HYDRAULIC BREAKERS
Operation
1. OPERATION METHOD
2. PROPER THRUST
1. To use the breaking force of a breaker effectively, a proper thrust has to be applied to the breaker. If the
thrust is insufficient, a hammering energy of the piston will not be efficiently used for breaking rocks. Thus,
the hammering force applies shock to the breaker body, arm and boom of the base machine, etc, resulting in
damage to those parts.
2. On the other hand, if thrust is excessive and breaking is performed with the front of the base machine raised,
the machine may suddenly tilt forward at the moment the rock is broken and the breaker body may violently
hit against the rock resulting in damage.
3. If hammering is performed under such a condition, vibrations during hammering may also be transmitted to
the tracks, and therefore, hammering in such a manner should be avoided to also protect the tracks. Further,
during hammering, take care to always apply a thrust to the breaker. Do not hammer with no thrust applying.
3. PRECAUTIONS IN OPERATION
To prevent blank hammering, the impacting power must be always applied in longitudinal direction to the tool.
Pressing
Pressing
Pressing
Pressing
34 | GB HYDRAULIC BREAKERS
Operation
Cracking
from edge.
3-5. Operate carefully not to hit the excavator with the tool.
Don’t hit
GB Hydraulic Breakers have a control valve for blows, please adjust blows with the control valve for blows
according to the field condition.
Check the oil temperature constantly to ensure it does not exceed 175℉(80℃). If higher temperatures are
measured in the tank, an oil cooler must be fitted.
36 | GB HYDRAULIC BREAKERS
Operation
3-13. Do not hammer with base machine cylinders moved to the stroke end.
Especially in winter, the base machine engine should be warmed up for five to ten minutes (about oil
temperature 30℃�40℃/80℉�105℉) before breaker operation. Follow the base machine instruction book for
warming-up of the engine.
During breaker operation, the breaker parts can reach high temperatures and thus should not be touched.
38 | GB HYDRAULIC BREAKERS
Inspection and maintenance
WARNING
● WHEN DISASSEMBLING OR REPAIRING THE BREAKER : THE CHARGING VALVE PLUG MAY COME
OFF DUE TO GAS PRESSURE. THIS IS VERY DANGEROUS. BE SURE TO RELEASE GAS OUT FROM
THE CHARGING VALVE PLUG BEFORE DISASSEMBLING. BEFORE FILLING THE CHARGING VALVE
PLUG WITH GAS, BE SURE TO COMPLETELY TIGHTEN THE BOLT.
● WHEN REPLACING THE GAS VALVE : THE GAS VALVE BODY MAY COME OFF DUE TO GAS
PRESSURE. BE SURE TO COMPLETELY RELEASE INTERNAL GAS OUT BEFORE REPLACING THE
GAS VALVE.
● WHEN FILLING THE GAS CUSHION CHAMBER OR THE HEAD CAP WITH NITROGEN GAS : THE
TOOL MAY JUMP OUT. TO AVOID ACCIDENTS, DO NOT STAND IN FRONT OF THE TOOL.
● BEFORE SERVICING, MAKE SURE RESIDUAL HYDRAULIC PRESSURE IS RELEASED.
IMPORTANT
USE ONLY THE HOSE NOZZLE TO RELIEVE THE PRESSURE : USING NAILS, SCREWDRIVERS OR
SIMILAR OBJECTS WILL DAMAGE THE FILLING VALVE.
Inspection
Inspection Item Inspection Point Interval
1. INSPECTION POINTS
T-SERIES
GB8AT
SECTION \ MODEL Part Unit GBM60 GBM90 GB1T GB2T GB3TP GB4T GB5T GB6T GB8T Inspection
Interval
(GB7T)
Tid rod fixing torque A kg.m 30~40 30~40 35~40 38~45 40~50 60~80 160~180 170~200 200~230 250~270 Every week
Accumulator
B kg.m - - - - - - - - - - Every week
fixing bolt
Accumulator charging
C kg.m - - - - - - - - - - Every week
plug fixing Torque
Back head N2 gas kg/cm 2 13~14 13~14 13~14 15~16 16~17 16~17 16~17 16~17 16~17 16~17
F (psi) Every week
pressure (at 20℃ / 68℉) - - 184~199 213~227 227~241 227~241 227~241 227~241 227~241 227~241
40 | GB HYDRAULIC BREAKERS
Inspection and maintenance
F-SERIES
Inspection
SECTION \ MODEL Part Unit GB150 GB8AF GB8F GB9F GB11F GB14F Interval
Tid rod fixing torque A kg.m 170~200 250~270 200~230 250~270 270~300 270~300 Every week
Accumulator
B kg.m 60~65 60~65 60~65 60~65 60~65 60~65 Every week
fixing bolt
Accumulator charging
C kg.m 8~12 8~12 8~12 8~12 8~12 8~12 Every week
plug fixing Torque
Side bolt fixing torque E kg.m 200~230 250~270 230~250 250~270 320~350 320~350 Every day
Back head N2 gas kg/cm 2 16~17 16~17 16~17 16~17 16~17 16~17
F (psi) Every week
pressure (at 20℃ / 68℉) 227~241 227~241 227~241 227~241 227~241 227~241
T-SERIES
Open Close
Valve adjuster direction
2. WEARING PARTS
When changing tool pin direction, place pin with this surface on tool side.
Tool
Tool Retainer
When replacing, check each part for wear, breakage, scoures, etc., especially, after removing burrs and
swelling on tool retainer and tool.
Replace tool after grinding the worn parts of lower bush and stop pin.
Wear Limit
2-4. Lower bush Dimension
Wear Limit of Tool and Lower Bush :
When the clearance between the tool and lower 6mm
bush becomes large, it is strongly recommended to
replace these to prevent other parts from wear.
Exceeding the wear limit dimension clearance may 6mm
Wear Limit
damage other component parts, such as pistons
Dimension
and cylinders.
42 | GB HYDRAULIC BREAKERS
Inspection and maintenance
3. OPERATIONAL PRESSURE
If the operating pressure of the breaker is regular and the pressure of the excavator itself is regular,
pressure does not need to be applied by attaching a relief valve to the high pressure line of the breaker.
Please get the help of the service department for applying pressure.
If the pressure is over regular pressure the breaker gets more impact which makes it a problem on the
breaker and the excavator.
4. OIL TEMPERATURE
The oil temperature will vary depending on operational conditions but it should range 50�80℃.
If it is over 80℃ it makes the accumulator rubber and o-ring’s life span shorter. Be cautious of the
following to avoid the rise in oil temperature.
5. OIL LEAKAGE
Check for oil leakages periodically. Minimum oil leakage, out of drain plug and between tool and tool
holder, should be disregarded as it helps keep the tool greased.
In cases of a lot of leakage check and replace the packings. Apply the working oil to the work-ing
packing, o-ring, gas-seal, dust seal and packing groove.
Applying grease (recommend cylinder grease) to o-ring is especially effective.
1. Check if there are any scratches on the packings. Check that they are well pressed and not pushed
out.
2. Be cautious of dirt of flow.
3. If the working packing gets damaged, check the packing and stroke piston.
4. And also check if the dust seal has been pushed out or wrongly connected or if there are any
scratches in the cylinder.
5. When the working packing and gas-seal is damaged oil will leak out.
Replace each packing and o-ring. Contact your local service dealer for assistance.
1. PROBLEMS IN OPERATION
If the breaker does not work or blow frequency and blow power get worse, check the arranged method.
And then inspect according to the following order.
SYMPTOM CAUSE REQUIRED ACTION
Sudden reduction 1. Accumulator gas leakage 1. Replace o-ring, or refill nitrogen gas
power and pressure
2. Accumulator diaphragm damage 2. Replace diaphragm
line vibration
44 | GB HYDRAULIC BREAKERS
Trouble shooting guide
No Breaker Function
2. GAS LEAKAGE
A. Gas leakage from the top of Defective o-ring in charging valve Replace
charging valve
Defective or damaged in charging Repair or replace charging
valve valve
B. Gas leakage between Defective o-ring in charging valve Replace
charging valve and back head
Charging valve loose in back head Re-tighten
D. Gas leakage from drain plug Defective gas seal in seal retainer Replace
hole
Defective step seal in seal retainer Replace
3. OIL LEAKAGE
Even if oil is leaking, there is no use to replacing parts at all times. Check the following points listed in the
chart below. The user can check the ( � ) marked points before calling dealer.
B
D C
F A
A Between the tool and A large amount of oil is leaking. Seals damaged
lower bush Check if it is coming from oil or
REPLACE
grease.
B Surface of breaker Oil leaking from hose and male � Loose breaker hoses and
adapter portion male adapter
RETIGHTEN
C Accumulator and Oil leakage from reassembly of Loose accumulator socket bolt
surface of cylinder accumulator after overhaul
RETIGHTEN
46 | GB HYDRAULIC BREAKERS
PART LIST
T-SERIES
GBM60/GBM90/GB1T/GB2T/GB3TP
- BREAKER BODY 48
∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙
GB4T/GB5T/GB6T/GB8AT(GB7T)/GB8T
- BREAKER BODY 60
∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙
F-SERIES
GB150/GB8AF/GB8F/GB9F/GB11F/GB14F
- BREAKER BODY 71
∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙
48 | GB HYDRAULIC BREAKERS
GBM60/GBM90/GB1T/GB2T/GB3TP
PART LIST
GBM60 GBM90 GB1T GB2T GB3TP
NO. PART NAME REMARKS
PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY
CYLINDER ASS'Y M6011000 M9011000 01T11000 02T11000 03T11000 NO.1~11
1 CYLINDER M6011010 1 M9011010 1 01T11010 1 02T11010 1 03T11010 1
2 SOCKET PLUG (TEFLON PLUG) ST12073 3 ST12073 3 BS11019 3 BS11013 3 BS11013 3
3 O-RING OP13003 3 OP13003 3 OP13003 3 OP13006 3 OP13006 3
4 DUST SEAL SD12015 1 SD12016 1 SD12017 1 SD12018 1 SD12018 1
5 U-PACKING SU12043 1 SU12045 1 SU12047 1 SU12048 1 SU12048 1
6 BUFFER RING SB12030 1 SB12032 1
7 MALE ADAPTER EM14040 2 EM14040 2 EM14040 2 EM14040 2 EM14040 2
8 O-RING OP13008 2 OP13008 2 OP13008 2 OP13008 2 OP13008 2
9 UNION CAP EU14048 2 EU14048 2 EU14048 2 EU14048 2 EU14048 2
10 AIR CHECK VALVE EV14039 1 EV14039 1
11 O-RING OP13007 1 OP13007 1 OP13007 1 OP13007 2 OP13007 2
12 PISTON M6012010 1 M9012010 1 01T12010 1 02T12010 1 03T12010 1
SEAL RETAINER ASS'Y M6013000 M9013000 01T13000 02T13000 02T13000 NO.13~18
13 SEAL RETAINER M6013010 1 M9013010 1 01T13010 1 02T13010 1 02T13010 1
14 GAS SEAL SG12001 1 SG12002 1 SG12003 1 SG12004 1 SG12004 1
15 STEP SEAL (U-PACKING) SS12062 2 SU12044 2 SU12046 2 SS12063 2 SS12063 2
16 O-RING OA13065 2 OA13055 2 OA13055 2
17 BUFFER RING SB12029 1 SB12031 1
18 O-RING OG13040 4 OG13040 4 OG13041 4 OA13054 4 OA13054 4
VALVE ASS’Y M9015000 M9015000 01T15000 02T15000 03T15000 NO.19~23
19 VALVE M9015020 1 M9015020 1 01T15020 1 02T15020 1 03T15020 1
20 VALVE PLUG M9015030 1 M9015030 1 01T15030 1 02T15030 1 03T15030 1
21 O-RING OP13014 1 OP13014 1 OP13016 1 OG13033 1 OP13020 1
22 O-RING OG13054 1 OG13054 1 OG13030 1 OG13031 1 OG13031 1
23 VALVE SLEEVE M9015040 1 M9015040 1 01T15040 1 02T15040 1 03T15040 1
BACK HEAD ASS'Y M6016000 M9016000 01T16000 02T16000 03T16000 NO.24~27
24 BACK HEAD M6016010 1 M9016010 1 01T16010 1 02T16010 1 03T16010 1
25 BACK HEAD CHARGING VALVE EV14036 1 EV14036 1 EV14036 1 EV14036 1 EV14036 1
26 CHARGING VALVE PLUG EV14037 1 EV14037 1 EV14037 1 EV14037 1 EV14037 1
27 O-RING OP13071 1 OP13071 1 OP13071 1 OP13071 1 OP13071 1
FRONT HEAD ASS’Y M6017000 M9017000 01T17000 02T17000 03T17000 NO.28~39
28 FRONT HEAD M6017010 1 M9017010 1 01T17010 1 02T17010 1 03T17010 1
29 LOWER BUSH M6017020 1 M9017020 1 01T17020 1 02T17020 1 03T17020 1
30 BUSH PIN M6017040 2 M9017040 2 01T17030 2 02T17030 2 03T17030 2
31 SPRING PIN (S) ES14007 4 ES14007 4 ES14009 4 ES14010 4 ES14010 4
32 SPRING PIN (L) ES14008 1 ES14008 1 ES14008 1 ES14011 1 ES14011 1
50 | GB HYDRAULIC BREAKERS
GBM60/GBM90/GB1T/GB2T/GB3TP
PART LIST
GBM60 GBM90
NO. PART NAME REMARKS
PART NO. Q’TY PART NO. Q’TY
1 FRAME (LH) M6021010 1 M9021010 1
2 FRAME (RH) M6021020 1 M9021020 1
SIDE HEX BOLT ASS’Y M6021100 M9021100 NO. 3~4
3 SIDE HEX BOLT BH11024 10 BH11028 10
4 SPRING WASHER BH11065 10 BH11066 10
5 HEX BOLT BH11025 10 BH11025 10
6 HEX NUT BH11054 20 BH11054 20
7 SPRING WASHER BH11065 10 BH11065 10
OIL HIGH PRESSURE HOSE OPTION 2 OPTION 2
OIL HOSE PLUG OPTION 2 OPTION 2
PART LIST
GB1T GB2T GB3TP
NO. PART NAME REMARKS
PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY
1 FRAME (LH) 01T21010 1 02T21010 1 03T21010 1
2 FRAME (RH) 01T21020 1 02T21020 1 03T21020 1
SIDE BOLT ASS’Y 01T21100 02T21100 03T21100 No. 3~5
3 SIDE BOLT BH11030 4 BH11032 4 BH11033 4
4 CAP NUT BH11050 4 BH11051 4 BH11051 4
5 SPRING WASHER BH11068 4 BH11069 4 BH11069 4
6 HEX BOLT BH11025 10 BH11025 10 BH11025 10
7 HEX NUT BH11054 20 BH11054 20 BH11054 20
8 SPRING WASHER BH11065 10 BH11065 10 BH11065 10
OIL HIGH PRESSURE HOSE OPTION OPTION 2 OPTION 2
OIL HOSE PLUG OPTION OPTION 2 OPTION 2
52 | GB HYDRAULIC BREAKERS
GBM60/GBM90/GB1T/GB2T/GB3TP
PART LIST
GBM60 GBM90 GB1T GB2T GB3TP
NO. PART NAME REMARKS
PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY
1 FRAME M6022010 1 M9022010 1 01T22010 1 02T22010 1 03T22010 1
2 COVER PLATE M6022020 1 M6022020 1 01T22020 1 02T22020 1 02T22020 1
3 HEX BOLT BH11025 8 BH11025 8 BH11025 8 BH11025 10 BH11025 10
4 HEX NUT BH11054 16 BH11054 16 BH11054 16 BH11054 16 BH11054 20
5 SPRING WASHER BH11065 8 BH11065 8 BH11065 8 BH11065 8 BH11065 10
6 MC COVER (A) M6022410 1 M9022410 1 01T22410 1 02T22410 1 03T22410 1
7 SOCKET BOLT BS11001 4 BS11001 4 BS11001 4 BS11001 4 BS11001 4
8 LOCKING WASHER BL11075 4 BL11075 4 BL11075 4 BL11075 4 BL11075 4
9 BOX DAMPER M6022280 1 M9022280 1 01T22280 1 02T22280 1 03T22280 1
10 UPPER DAMPER M9022220 1 M9022220 1 01T22220 1 02T22220 1 02T22220 1
11 COVER DAMPER EC14021 2 EC14021 2 EC14021 2 EC14021 2 EC14021 2
12 RUBBER CAP (2) ER14013 2 ER14013 2 ER14013 2 ER14013 2
13 RUBBER CAP (1) ER14012 4 ER14012 2 ER14012 2 ER14012 2 ER14012 2
14 RUBBER CAP (G1) ER14025 1 ER14025 1 ER14025 1 ER14025 1 ER14025 1
15 HOSE GUIDE EH14027 2 EH14027 2
OIL HIGH PRESSURE HOSE OPTION 2 OPTION 2 OPTION 2 OPTION 2 OPTION 2
OIL HOSE PLUG OPTION 2 OPTION 2 OPTION 2 OPTION 2 OPTION 2
54 | GB HYDRAULIC BREAKERS
GBM60/GBM90/GB1T/GB2T/GB3TP
PART LIST
GBM60 GBM90
NO. PART NAME REMARKS
PART NO. Q’TY PART NO. Q’TY
1 FRAME (LH) M6023010 1 M9023010 1
2 FRAME (RH) M6023020 1 M9023020 1
SIDE BOLT ASS’Y M6023100 M9023100 NO. 3~5, 8
3 SIDE BOLT BH11026 1 BH11026 1
4 CAP NUT BH11048 1 BH11048 1
5 SPRING WASHER BH11067 1 BH11067 1
6 SIDE HEX BOLT BH11024 10 BH11028 10
7 SPRING WASHER BH11065 10 BH11066 10
8 DISTANCE PIPE M6023060 1 M9023060 1
BRACKET PIN ASS’Y M6023200 M9023200 NO. 9~12
9 PIN M6023210 2 M9023210 2 (OPTION)
10 STOP RING M6023220 2 M9023220 2 (OPTION)
11 HEX BOLT BH11027 2 BH11027 2 (OPTION)
12 HEX NUT BH11055 4 BH11055 4 (OPTION)
OIL HIGH PRESSURE HOSE OPTION 2 OPTION 2
OIL HOSE PLUG OPTION 2 OPTION 2
PART LIST
GB1T GB2T GB3TP
NO. PART NAME REMARKS
PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY
1 FRAME (LH) 01T23010 1 02T23010 1 03T23010 1
2 FRAME (RH) 01T23020 1 02T23020 1 03T23020 1
SIDE BOLT ASS’Y 01T23100 02T23100 03T23100 NO. 3~7
3 SIDE BOLT BH11030 5 BH11032 5 BH11033 5
4 CAP NUT BH11050 5 BH11051 5 BH11051 5
5 SPRING WASHER BH11068 5 BH11069 5 BH11069 5
6 DISTANCE PIPE 01T23060 1 02T23060 1 03T23060 1
BRACKET PIN ASS’Y 01T23200 02T23200 03T23200 NO. 7~10
7 PIN 01T23210 2 02T23210 2 03T23210 2 (OPTION)
8 STOP RING 01T23220 2 02T23220 2 03T23220 2 (OPTION)
9 HEX BOLT BH11027 2 BH11034 2 BH11034 2 (OPTION)
10 HEX NUT BH11055 4 BH11056 4 BH11056 4 (OPTION)
OIL HIGH PRESSURE HOSE OPTION 2 OPTION 2 OPTION 2
OIL HOSE PLUG OPTION 2 OPTION 2 OPTION 2
56 | GB HYDRAULIC BREAKERS
GBM60/GBM90/GB1T/GB2T/GB3TP
PART LIST
GBM60 GBM90
NO. PART NAME REMARKS
PART NO. Q’TY PART NO. Q’TY
1 FRAME (LH) M6025010 1 M9025010 1
2 FRAME (RH) M6025020 1 M9025020 1
SIDE BOLT ASS’Y M6025100 M9025100 NO. 3~5
3 SIDE BOLT BH11026 1 BH11026 1
4 CAP NUT BH11049 1 BH11049 1
5 SPRING WASHER BH11067 1 BH11067 1
6 SIDE HEX BOLT BH11024 10 BH11028 10
7 SPRING WASHER BH11065 10 BH11066 10
OIL HIGH PRESSURE HOSE OPTION 2 OPTION 2
OIL HOSE PLUG OPTION 2 OPTION 2
PART LIST
GB1T GB2T GB3TP
NO. PART NAME REMARKS
PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY
1 FRAME (LH) 01T25010 1 02T25010 1 03T25010 1
2 FRAME (RH) 01T25020 1 02T25020 1 03T25020 1
SIDE BOLT ASS’Y 01T25100 02T25100 NO. 3~5
3 SIDE BOLT BH11030 4 BH11032 4 BH11033 4
4 CAP NUT BH11050 4 BH11051 4 BH11051 4
5 SPRING WASHER BH11068 4 BH11069 4 BH11069 4
OIL HIGH PRESSURE HOSE OPTION 2 OPTION 2 OPTION 2
OIL HOSE PLUG OPTION 2 OPTION 2 OPTION 2
58 | GB HYDRAULIC BREAKERS
GBM60/GBM90/GB1T/GB2T/GB3TP
PART LIST
NO. PART NAME PART NO. Q’TY REMARKS
60 | GB HYDRAULIC BREAKERS
GB4T/GB5T/GB6T/GB8AT(GB7T)/GB8T
PART LIST
GB4T GB5T GB6T GB8AT(GB7T) GB8T
NO. PART NAME REMARKS
PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY
CYLINDER ASS’Y 04T11000 05T11000 06T11000 08AT11000 08T11000 No.1~18
1 CYLINDER 04T11010 1 05T11010 1 06T11010 1 08AT11010 1 08T11010 1
2 SOCKET PLUG BS11014 3 BS11015 3 BS11016 3 BS11016 3 BS11017 3
3 O-RING OP13007 3 OP13009 4 OP13009 3 OP13009 3 OP13011 3
4 DUST SEAL SD12019 1 SD12020 1 SD12022 1 SD12023 1 SD12023 1
5 U-PACKING SU12049 1 SU12051 1 SU12053 1 SU12055 1 SU12055 1
6 BUFFER SEAL SB12034 1 SB12035 1 SB12037 1 SB12038 1 SB12038 1
7 VALVE ADJUSTER 05T11030 1 06T11030 1 08T11030 1 08T11030 1
8 O-RING OP13002 1 OP13002 1 OP13003 1 OP13003 1
9 BACK UP RING BP20001 1 BP20001 1 BP20002 2 BP20002 2
10 HEX NUT BH11078 1 BH11078 1 BH11079 1 BH11079 1
11 ADJUSTER SOCKET 05T11110 1
12 O-RING OP13014 1
13 MALE ADAPTER EM14041 2 EM14041 2 EM14042 2 EM14043 2 EM14043 2
14 O-RING OP13010 2 OP13010 2 OP13013 2 OP13019 2 OP13019 2
15 UNION CAP EU14049 2 EU14049 2 EU14050 2 EU14050 2 EU14050 2
16 DOWEL PIN 22E11070 1 22E11070 1 22E11070 2 22E11070 2 22E11070 2
17 AIR CHECK VALVE EV14039 1 EV14039 1 EV14039 1 EV14039 1 EV14039 1
18 O-RING OP13007 2 OP13007 2 OP13007 2 OP13007 2 OP13007 2
19 PISTON 04T12010 1 05T12010 1 06T12010 1 08AT12010 1 08T12010 1
SEAL RETAINER ASS’Y 04T13000 05T13000 06T13000 08T13000 08T13000 No.20~25
20 SEAL RETAINER 04T13010 1 05T13010 1 06T13010 1 08T13010 1 08T13010 1
21 GAS SEAL SG12005 1 SG12006 1 SG12008 1 SG12011 1 SG12011 1
22 STEP SEAL (U-PACKING) SS12064 2 SU12050 2 SS12066 2 SS12069 2 SS12069 2
23 O-RING OA13056 2 OA13058 2 OA13060 2 OA13060 2
24 O-RING OG13045 4 OG13046 4 OG13047 3 OG13049 3 OG13049 3
25 BACK UP RING BG20020 1 BG20009 1 BG20009 1
VALVE ASS’Y 04T15000 05T15000 06T15000 08AT15000 08T15000 No.26~30
26 VALVE 04T15020 1 05T15020 1 06T15020 1 08AT15020 1 08T15020 1
27 VALVE PLUG 04T15030 1 05T15030 1 06T15030 1 08AT15030 1 08T15030 1
28 O-RING OG13034 1 OP13022 1 OG13038 1 OG13040 1 OG13041 1
29 O-RING OG13031 1 OG13032 1 OG13034 1 OG13035 1 OG13034 1
30 VALVE SLEEVE 04T15040 1 05T15040 1 06T15040 1 08AT15040 1 08T15040 1
BACK HEAD ASS’Y 04T16000 05T16000 06T16000 08AT16000 08T16000 No.31~34
31 BACK HEAD 04T16010 1 05T16010 1 06T16010 1 08AT16010 1 08T16010 1
31-1 BACK HEAD (BOX) 08AT16110 1 08T16110 1
32 BACK HEAD CHARGING VALVE EV14036 1 EV14036 1 EV14036 1 EV14036 1 EV14036 1
62 | GB HYDRAULIC BREAKERS
GB4T/GB5T/GB6T/GB8AT(GB7T)/GB8T
PART LIST
GB4T GB5T GB6T GB8AT(GB7T) GB8T
NO. PART NAME REMARKS
PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY
1 FRAME (LH) 04T21010 1 05T21010 1 06T21010 1 8AT21010 1 08T21010 1
2 FRAME (RH) 04T21020 1 05T21020 1 06T21020 1 8AT21020 1 08T21020 1
SIDE BOLT ASS’Y 04T21100 05T21100 06T21100 22E21100 22E21100 No. 3~5
3 SIDE BOLT BH11035 6 BH11037 6 06T21110 8 22E21110 8 22E21110 8
4 WASHER BH11052 6 BH11053 6 06T21120 16 22E21120 8 22E21120 8
5 SIDE HEX NUT BH11070 6 BH11071 6 06T21130 16 22E21130 16 22E21130 16
6 HEX BOLT BH11036 10 BH11036 12 BH11038 12 BH11038 12 BH11038 12
7 HEX NUT BH11057 20 BH11057 24 BH11058 24 BH11058 24 BH11058 24
8 SPRING WASHER BH11067 10 BH11067 12 BH11068 12 BH11068 12 BH11068 12
OIL HIGH PRESSURE HOSE OPTION 2 OPTION 2 OPTION 2 OPTION 2 OPTION 2
OIL HOSE PLUG OPTION 2 OPTION 2 OPTION 2 OPTION 2 OPTION 2
64 | GB HYDRAULIC BREAKERS
GB4T/GB5T/GB6T/GB8AT(GB7T)/GB8T
PART LIST
GB4T GB5T GB6T
NO. PART NAME REMARKS
PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY
1 FRAME 04T22010 1 05T22010 1 06T22010 1
2 COVER PLATE 04T22020 1 05T22020 1 06T22020 1
3 HEX BOLT BH11036 12 BH11036 12 BH11040 12
4 HEX BOLT BH11073 4 BH11073 4 BH11074 4
5 HEX NUT BH11057 28 BH11057 28 BH11058 28
6 SPRING WASHER BH11067 16 BH11067 16 BH11068 16
7 GUIDE PLATE 04T22100 1 05T22100 1 06T22100 1
8 SOCKET BOLT BS11077 2 BS11077 2 BS11077 2
9 MC COVER (A) 04T22410 1 05T22410 1 06T22410 1
10 MC COVER (B) 04T22420 1 05T22420 1 06T22420 1
11 SOCKET BOLT BS11002 8 BS11002 8 BS11002 8
12 LOCKING WASHER BL11076 8 BL11076 8 BL11076 8
13 BOTTOM DAMPER 04T22210 1 05T22210 1 06T22210 1
14 UPPER DAMPER 04T22220 1 05T22220 1 06T22220 1
15 LOWER PLATE 1 04T22230 1 05T22230 1 06T22230 1
16 LOWER PLATE 3 04T22280 1 05T22230 1 06T22230 1
17 LOWER PLATE 2 04T22240 2 05T22240 2 22E22240 2
18 UPPER PLATE 1 04T22250 1 05T22250 2 22E22250 2
19 UPPER PLATE 04T22250 1 05T22250 1 22E22260 2
20 UPPER PLATE 2 04T22260 1 05T22260 1 22E22260 2
21 CUSHION DAMPER 04T22270 2 22E22270 2 22E22270 2
22 COVER DAMPER EC14022 2 EC14022 2 EC14022 2
23 RUBBER CAP ER14014 6 ER14014 6 ER14014 6
24 RUBBER CAP (T) ER14063 2 ER14018 2 ER14019 2
25 RUBBER CAP (G) ER14025 1 ER14025 1 ER14026 1
26 HOSE GUIDE EH14028 2 EH14028 2 EH14029 2
OIL HIGH PRESSURE HOSE OPTION 2 OPTION 2 OPTION 2
OIL HOSE PLUG OPTION 2 OPTION 2 OPTION 2
66 | GB HYDRAULIC BREAKERS
GB4T/GB5T/GB6T/GB8AT(GB7T)/GB8T
PART LIST
GB8AT (GB7T) GB8T
NO. PART NAME REMARKS
PART NO. Q’TY PART NO. Q’TY
1 FRAME 8AT22010 1 08T22010 1
2 COVER PLATE 8AT22020 1 8AT22020 1
3 HEX BOLT BH11040 12 BH11040 12
4 HEX NUT BH11058 24 BH11058 24
5 SPRING WASHER BH11068 12 BH11068 12
6 COVER (A) 8AT22060 1 08T22060 1
7 HEX BOLT BH11083 4 BH11083 4
8 SPRING WASHER BH11065 4 BH11065 4
9 A-G BASE 08T22090 1 08T22090 1
10 HEX BOLT BH11084 2 BH11084 2
11 SPRING WASHER BH11067 2 BH11067 2
12 BODY SUPPORT 8AT22030 1 8AT22030 1
13 SOCKET BOLT BS11077 2 BS11077 2
14 BUSH 8AT22050 2 8AT22050 2
15 SIDE BOLT 22E21110 1 22E21110 1
16 SIDE HEX NUT 22E21130 2 22E21130 2
17 BODY CAP 8AT22040 1 08T22040 1
18 MC COVER (A) 8AT22410 1 8AT22410 1
19 MC COVER (B) 8AT22420 1 08T22420 1
20 SOCKET BOLT BS11002 8 BS11002 8
21 LOCKING WASHER BL11076 8 BL11076 8
22 BOTTOM DAMPER 8AT22210 1 08T22210 1
23 UPPER DAMPER 22E22220 1 22E22220 1
24 LOWER PLATE 1 22E22230 2 22E22230 2
25 LOWER PLATE 2 08T22240 2 08T22240 2
26 UPPER PLATE 1 22E22250 2 22E22250 2
27 UPPER PLATE 2 22E22260 4 22E22260 4
28 CUSHION DAMPER 22E22270 2 22E22270 2
29 COVER DAMPER EC14023 2 EC14023 2
30 RUBBER CAP ER14017 6 ER14017 6
31 RUBBER CAP (G) ER14026 1 ER14026 1
32 HOSE GUIDE EH14029 2 EH14029 2
33 RUBBER CAP (G3) ER14027 1 ER14027 1
OIL HIGH PRESSURE HOSE OPTION 2 OPTION 2
OIL HOSE PLUG OPTION 2 OPTION 2
PART LIST
GB4T GB5T GB6T GB8AT(GB7T) GB8T
NO. PART NAME REMARKS
PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY
1 FRAME 04T23030 1 05T23030 1 06T23030 1 8AT23030 1 08T23030 1
2 SET PLATE 04T23040 2 05T23040 2 06T23040 2 8AT23040 1 08T23040 1
3 GUIDE PLATE 04T23050 2 05T23050 2 06T23050 2 8AT23050 1 08T23050 1
SIDE BOLT ASS’Y 04T23100 05T23100 06T21100 22E21100 22E21100 NO. 4~6
4 SIDE BOLT BH11035 6 BH11037 6 06T21110 6 22E21110 8 22E21110 8
5 WASHER BH11052 6 BH11053 6 06T21120 12 22E21120 16 22E21120 16
6 SIDE HEX NUT BH11070 6 BH11071 6 06T21130 12 22E21130 16 22E21130 16
BRACKET PIN ASS’Y 04T23200 05T23200 06T23200 8AT23200 08T23200 NO. 7~11
7 PIN 04T23210 2 05T23210 2 06T23210 2 8AT23210 2 08T23210 2 (OPTION)
8 DISTANCE BUSH 04T23230 2 05T23230 4 06T23230 4 8AT23230 4 08T23230 4 (OPTION)
9 STOP RING 04T23220 2 05T23220 2 06T23220 2 8AT23220 2 08T23220 2 (OPTION)
10 HEX BOLT BH11034 2 BH11034 2 BH11039 2 BH11041 2 BH11041 2 (OPTION)
11 HEX NUT BH11056 4 BH11056 4 BH11054 4 BH11054 4 BH11054 4 (OPTION)
OIL HIGH PRESSURE HOSE OPTION 2 OPTION 2 OPTION 2 OPTION 2 OPTION 2
OIL HOSE PLUG OPTION 2 OPTION 2 OPTION 2 OPTION 2 OPTION 2
68 | GB HYDRAULIC BREAKERS
GB4T/GB5T/GB6T/GB8AT(GB7T)/GB8T
PART LIST
GB4T GB5T
NO. PART NAME REMARKS
PART NO. Q’TY PART NO. Q’TY
1 FRAME (LH) 04T25010 1 05T25010 1
2 FRAME (RH) 04T25020 1 05T25020 1
SIDE BOLT ASS’Y NO. 3~5
3 SIDE BOLT BH11035 6 BH11037 6
4 CAP NUT BH11052 6 BH11053 6
5 SPRING WASHER BH11070 6 BH11071 6
OIL HIGH PRESSURE HOSE OPTION 2 OPTION 2
OIL HOSE PLUG OPTION 2 OPTION 2
PART LIST
NO. PART NAME PART NO. Q’TY REMARKS
1 FRAME 08T24010 1
2 HEX BOLT BH12015 12
3 HEX NUT BH12035 56
4 SPRING WASHER BH12045 28
5 DISTANCE BOLT 08T24070 2
6 SIDE HEX NUT BH12030 4
7 WASHER BH12048 2
8 HEX BOLT BH11085 16
9 COVER PLATE 08T24020 1
10 SUPPORT PLATE-L 08T24030 1
11 SUPPORT PLATE-H 08T24040 1
12 DISTANCE PLATE 08T24050 1
13 BUMPER 22E24060 6
OIL HIGH PRESSURE HOSE OPTION 2
OIL HOSE PLUG OPTION 2
70 | GB HYDRAULIC BREAKERS
GB150/GB8AF/GB8F/GB9F/GB11F/GB14F
PART LIST
GB150 GB8AF GB8F GB9F GB11F GB14F
NO. PART NAME REMARKS
PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY
CYLINDER ASS’Y 15K11000 08AF11000 08F11000 09F11000 11F11000 14F11000 No.1~17
1 CYLINDER 15K11010 1 08AF11010 1 08F11010 1 09F11010 1 11F11010 1 14F11010 1
2 SOCKET PLUG BS11016 3 BS11016 3 BS11016 3 BS11017 3 BS11018 3 BS11018 3
3 O-RING OP13009 3 OP13009 3 OP13009 3 OP13011 3 OP13015 3 OP13015 3
4 DUST SEAL SD12021 1 SD12023 1 SD12023 1 SD12023 1 SD12025 1 SD12026 1
5 U-PACKING SU12052 1 SU12055 1 SU12055 1 SU12055 1 SU12057 1 SU12059 1
6 BUFFER SEAL SB12036 1 SB12038 1 SB12038 1 SB12038 1 SB12040 1 SB12041 1
7 VALVE ADJUSTER 06T11030 1 08T11030 1 08T11030 1 08T11030 1 11F11030 1 11F11030 1
8 O-RING OP13002 1 OP13003 1 OP13003 1 OP13003 1 OP13005 1 OP13005 1
9 BACK UP RING BP20001 1 BP20002 2 BP20002 2 BP20002 2 BP20004 2 BP20004 2
10 HEX NUT BH11078 1 BH11079 1 BH11079 1 BH11079 1 BH11080 1 BH11080 1
11 MALE ADAPTER EM14042 2 EM14043 2 EM14043 2 EM14043 2 EM14044 2 EM14044 2
12 O-RING OP13013 2 OP13019 2 OP13019 2 OP13019 2 OP13021 2 OP13021 2
13 UNION CAP EU14050 2 EU14050 2 EU14050 2 EU14050 2 EU14052 2 EU14052 2
14 DOWEL PIN 22E11070 2 22E11070 2 22E11070 2 22E11070 2 22E11070 2 22E11070 2
15 AIR CHECK VALVE EV14039 1 EV14039 1 EV14039 1 EV14039 1 EV14039 1 EV14039 1
16 O-RING OP13007 2 OP13007 2 OP13007 2 OP13007 2 OP13007 2 OP13007 2
17 HELI SERT COIL 22E11120 4 22E11120 4 22E11120 4 22E11120 4 22E11130 4 22E11130 4
18 PISTON 15K12010 1 08AT12010 1 08T12010 1 08T12010 1 11F12010 1 14F12010 1
SEAL RETAINER ASS’Y 15K13000 08T13000 08T13000 08T13000 11F13000 14F13000 No.19~24
19 SEAL RETAINER 15K13010 1 08T13010 1 08T13010 1 08T13010 1 11F13010 1 14F13010 1
20 GAS SEAL SG12007 1 SG12011 1 SG12011 1 SG12011 1 SG12012 1 SG12014 1
21 STEP SEAL SS12065 2 SS12069 2 SS12069 2 SS12069 2 SS12070 2 SS12071 2
22 O-RING OA13057 2 OA13060 2 OA13059 2 OA13060 2 OA13062 2 OA13064 2
23 O-RING OG13047 3 OG13049 3 OG13049 3 OG13049 3 OG13050 3 OG13052 3
24 BACK UP RING BG20020 1 BG20009 1 BG20009 1 BG20009 1 BG20010 1 BG20021 1
ACCUMULATOR ASS’Y 15K14000 08F14000 08F14000 08F14000 11F14000 11F14000 No.25~41
25 ACCUMULATOR BODY 15K14010 1 08F14010 1 08F14010 1 08F14010 1 11F14010 1 11F14010 1
26 O-RING OG13070 1 OG13042 1 OG13042 1 OG13042 1 OP13022 1 OP13022 1
27 BACK UP RING BG40014 1 BG40009 1 BG40009 1 BG40009 1 BG40006 1 BG40006 1
28 ACCUMULATOR COVER 15K14020 1 08F14020 1 08F14020 1 08F14020 1 11F14020 1 11F14020 1
29 DIAPHRAM 17E14030 1 08F14030 1 08F14030 1 08F14030 1 11F14030 1 11F14030 1
30 ACCUMULATOR CHARGING VALVE EV14060 1 EV14060 1 EV14060 1 EV14060 1 EV14060 1 EV14060 1
31 O-RING OP13001 1 OP13001 1 OP13001 1 OP13001 1 OP13001 1 OP13001 1
32 ACCUMULATOR CHARGING VALVE CAP EV14061 1 EV14061 1 EV14061 1 EV14061 1 EV14061 1 EV14061 1
33 O-RING OP13005 2 OP13005 2 OP13005 2 OP13005 2 OP13005 2 OP13005 2
34 CHARGING PLUG 22E14050 1 22E14050 1 22E14050 1 22E14050 1 22E14050 1 22E14050 1
35 HOLDER PIN 15K14060 1 22E14060 1 22E14060 1 22E14060 1 11F14060 1 11F14060 1
36 HOLDER(A) 15K14070 1 22E14070 1 22E14070 1 22E14070 1 11F14070 1 11F14070 1
37 HOLDER(B) 15K14080 1 22E14080 1 22E14080 1 22E14080 1 11F14080 1 11F14080 1
38 HOLDER(C) 15K14090 1 22E14090 1 22E14090 1 22E14090 1 11F14090 1 11F14090 1
39 CENTER PIN 15K14100 1 22E14100 1 22E14100 1 22E14100 1 11F14100 1 11F14100 1
72 | GB HYDRAULIC BREAKERS
GB150/GB8AF/GB8F/GB9F/GB11F/GB14F
SIDE PLATE TYPE BRACKET | GB150, GB8AF, GB8F, GB9F, GB11F, GB14F
PART LIST
GB150 GB8AF GB8F GB9F GB11F GB14F
NO. PART NAME REMARKS
PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY
1 FRAME (LH) 15K21010 1 8AT21010 1 08F21010 1 08T21010 1 11F21010 1 14F21010 1
2 FRAME (RH) 15K21020 1 8AT21020 1 08F21020 1 08T21020 1 11F21020 1 14F21020 1
SIDE BOLT ASS’Y 06T21100 22E21100 08F21100 22E21100 11F21100 14F21100 No. 3~5
3 SIDE BOLT 06T21110 8 22E21110 8 08F21110 8 22E21110 8 11F21110 8 14F21110 8
4 WASHER 06T21120 16 22E21120 8 08F21120 16 22E21120 8 11F21120 16 14F21120 16
5 SIDE HEX NUT 06T21130 16 22E21130 16 08F21130 16 22E21130 16 11F21130 16 14F21130 16
6 HEX BOLT BH11038 12 BH11038 12 BH11040 12 BH11038 12 BH11042 12 BH11042 12
7 HEX NUT BH11058 24 BH11058 24 BH11060 24 BH11058 24 BH11062 24 BH11062 24
8 SPRING WASHER BH11068 12 BH11068 12 BH11068 12 BH11068 12 BH11070 12 BH11070 12
OIL HIGH PRESSURE HOSE OPTION 2 OPTION 2 OPTION 2 OPTION 2 OPTION 2 OPTION 2
OIL HOSE PLUG OPTION 2 OPTION 2 OPTION 2 OPTION 2 OPTION 2 OPTION 2
74 | GB HYDRAULIC BREAKERS
GB150/GB8AF/GB8F/GB9F/GB11F/GB14F
PART LIST
NO. PART NAME PART NO. Q’TY REMARKS
1 FRAME 15K22010 1
2 COVER PLATE 15K22020 1
3 HEX BOLT BH11040 12
4 HEX BOLT BH11074 4
5 HEX NUT BH11058 28
6 SPRING WASHER BH11068 16
7 GUIDE PLATE 06T22100 1
8 SOCKET BOLT BS11077 2
9 MC COVER (A) 06T22410 1
10 MC COVER (B) 15K22420 1
11 SOCKET BOLT BS11002 8
12 LOCKING WASHER BL11076 8
13 BOTTOM DAMPER 06T22210 1
14 UPPER DAMPER 06T22220 1
15 LOWER PLATE 1 15K22230 2
16 LOWER PLATE 2 15K22240 2
17 UPPER PLATE 1 22E22250 2
18 UPPER PLATE 2 22E22260 4
19 CUSHION DAMPER 22E22270 2
20 COVER DAMPER EC14022 2
21 RUBBER CAP ER14017 6
22 RUBBER CAP (T) ER14019 2
23 RUBBER CAP (G) ER14025 1
24 HOSE GUIDE EH14029 2
OIL HIGH PRESSURE HOSE OPTION 2
OIL HOSE PLUG OPTION 2
76 | GB HYDRAULIC BREAKERS
GB150/GB8AF/GB8F/GB9F/GB11F/GB14F
PART LIST
GB8AF GB8F GB9F GB11F GB14F
NO. PART NAME REMARKS
PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY
1 FRAME 8AF22010 1 08F22010 1 09F22010 1 11F22010 1 14F22010 1
2 COVER PLATE 8F22020 1 08F22020 1 08F22020 1 11F22020 1 11F22020 1
3 HEX BOLT BH11040 12 BH11040 12 BH11040 12 BH11042 12 BH11042 12
4 HEX NUT BH11058 24 BH11058 24 BH11058 24 BH11062 24 BH11062 24
5 SPRING WASHER BH11068 12 BH11068 12 BH11068 12 BH11070 12 BH11070 12
6 COVER (A) 8AT22060 1 08F22060 1 09F22060 1 11F22060 1 14F22060 1
7 HEX BOLT BH11083 4 BH11083 4 BH11083 4 BH11084 4 BH11084 4
8 SPRING WASHER BH11065 4 BH11065 4 BH11065 4 BH11067 4 BH11067 4
9 A-G BASE 08T22090 1 08T22090 1 08T22090 1 53E22090 1 53E22090 1
10 HEX BOLT BH11084 2 BH11084 2 BH11084 2 BH11084 2 BH11084 2
11 SPRING WASHER BH11067 2 BH11067 2 BH11067 2 BH11067 2 BH11067 2
12 BODY SUPPORT 8AT22030 1 8AT22030 1 8AT22030 1 11F22030 1 11F22030 1
13 SOCKET BOLT BS11077 2 BS11077 2 BS11077 2 BS11077 2 BS11077 2
14 BUSH 8AT22050 2 8AT22050 2 8AT22050 2 11F22050 2 14F22050 2
15 SIDE BOLT 22E21110 1 22E21110 1 22E21110 1 11F21110 1 14F21110 1
16 SIDE HEX NUT 22E21130 2 22E21130 2 22E21130 2 11F21130 2 14F21130 2
17 BODY CAP 8AT22040 1 08F22040 1 08T22040 1 11F22040 1 14F22040 1
18 MC COVER (A) 8AT22410 1 8AT22410 1 8AT22410 1 11F22410 1 11F22410 1
19 MC COVER (B) 8AF22420 1 08F22420 1 09F22420 1 11F22420 1 14F22420 1
20 SOCKET BOLT BS11002 8 BS11002 8 BS11002 8 BS11002 10 BS11002 10
21 LOCKING WASHER BL11076 8 BL11076 8 BL11076 8 BL11076 10 BL11076 10
22 BOTTOM DAMPER 8AT22210 1 08F22210 1 08T22210 1 11F22210 1 14F22210 1
23 UPPER DAMPER 22E22220 1 22E22220 1 22E22220 1 11F22220 1 11F22220 1
24 LOWER PLATE 1 22E22230 2 22E22230 2 22E22230 2 11F22230 2 11F22230 2
25 LOWER PLATE 2 08T22240 2 08T22240 2 08T22240 2 11F22240 2 11F22240 2
26 UPPER PLATE 1 22E22250 2 22E22250 2 22E22250 2 11F22250 2 11F22250 2
27 UPPER PLATE 2 22E22260 4 22E22260 4 22E22260 4 11F22260 4 11F22260 4
28 CUSHION DAMPER 22E22270 2 22E22270 2 22E22270 2 60E22270 2 60E22270 2
29 COVER DAMPER EC14023 2 EC14023 2 EC14023 2 EC14024 2 EC14064 2
30 RUBBER CAP ER14017 6 ER14017 6 ER14017 6 ER14017 6 ER14017 6
31 RUBBER CAP (G) ER14026 1 ER14026 1 ER14026 1 ER14026 1 ER14026 1
32 HOSE GUIDE EH14029 2 EH14029 2 EH14029 2 EH14030 2 EH14030 2
33 RUBBER CAP (G3) ER14027 1 ER14027 1 ER14027 1 ER14027 1 ER14027 1
OIL HIGH PRESSURE HOSE OPTION 2 OPTION 2 OPTION 2 OPTION 2 OPTION 2
OIL HOSE PLUG OPTION 2 OPTION 2 OPTION 2 OPTION 2 OPTION 2
78 | GB HYDRAULIC BREAKERS
GB150/GB8AF/GB8F/GB9F/GB11F/GB14F
PART LIST
GB150 GB8AF GB8F GB9F GB11F GB14F
NO. PART NAME REMARKS
PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY PART NO. Q’TY
1 FRAME 15K23030 1 8AT23030 1 08F23030 1 08T23030 1 11F23030 1 14F23030 1
2 SET PLATE 15K23040 2 8AT23040 1 08F23040 1 08T23040 1 11F23040 1 14F23040 1
3 GUIDE PLATE 15K23050 2 8AT23050 1 08F23050 1 08T23050 1 11F23050 1 14F23050 1
SIDE BOLT ASS’Y 06T21100 22E21100 22E21100 22E21100 11F21100 14F21100 No.4~6
4 SIDE BOLT 06T21110 6 22E21110 8 22E21110 8 22E21110 8 11F21110 8 14F21110 8
5 WASHER 06T21120 12 22E21120 16 22E21120 16 22E21120 16 11F21120 16 11F21120 16
6 SIDE HEX NUT 06T21130 12 22E21130 16 22E21130 16 22E21130 16 11F21130 16 11F21130 16
BRACKET PIN ASS’Y 06T23200 8AT23200 08F23200 08T23200 11F23200 14F23200 No.7~11
7 PIN 06T23210 2 8AT23210 2 08F23210 2 08T23210 2 11F23210 2 11F23210 2 (OPTION)
8 DISTANCE BUSH 06T23230 4 8AT23230 4 08F23230 4 08T23230 4 11F23230 4 14F23230 4 (OPTION)
9 STOP RING 06T23220 2 8AT23220 2 08F23220 2 08T23220 2 11F23220 2 11F23220 2 (OPTION)
10 HEX BOLT BH11039 2 BH11041 2 BH11041 2 BH11041 2 BH11045 2 BH11045 2 (OPTION)
11 HEX NUT BH11054 4 BH11054 4 BH11054 4 BH11054 4 BH11059 4 BH11059 4 (OPTION)
OIL HIGH PRESSURE HOSE OPTION 2 OPTION 2 OPTION 2 OPTION 2 OPTION 2 OPTION 2
OIL HOSE PLUG OPTION 2 OPTION 2 OPTION 2 OPTION 2 OPTION 2 OPTION 2
Serial number
Year of construction
www.gbhammer.com GB Hydraulic Breaker