Professional Documents
Culture Documents
U n d e rc o a t s 800K 2K Primer Surfacer - U.S. National Rule Primer Surfacer Application with LH810, LH820
800K 2K Primer Surfacer - U.S. National Rule Primer Surfacer Application with LHF, LHM, LHS
800K 2K Primer Surfacer - U.S. National Rule Tinted Wet-On-Wet Sealer Application with LHF,
LHM, LHS
800K 2K Primer Surfacer - U.S. National Rule Tinted Wet-On-Wet Sealer Application with LHF,
LHM, LHS - MEXICO ONLY
846 1K Acrylic Primer - U.S. National Rule Primer Application
H1000 1K Waterborne Primer - Low VOC Primer Surfacer Application
LP20 Epoxy Primer - U.S. National Rule Primer Application
LP20 Epoxy Primer - Low VOC Primer Application
LP20 Epoxy Primer - U.S. National Rule Primer Surfacer Application
LP20 Epoxy Primer - Low VOC Primer Surfacer Application
LP20 Epoxy Primer - Wet-On-Wet Sealer Application
LP20 Epoxy Primer - Low VOC Wet-On-Wet Sealer Application
LP100 Etch Primer - U.S. National Rule Primer Application
LP100 Etch Primer - Low VOC Primer Application
LP610 Low VOC Primer - Low VOC Primer Surfacer Application
LP610 Low VOC Primer - Low VOC Sealer Application
LP620 Low VOC Primer - U.S. National Rule Primer Surfacer Application
LP620 Low VOC Primer - Low VOC Primer Surfacer Application
LP620 Low VOC Primer - U.S. National Rule Sealer Application
LP620 Low VOC Primer - Low VOC Sealer Application
LS56 1K Sealer - U.S. National Rule Wet-On-Wet Sealer Application
LS800 2K Sealer - U.S. National Rule Wet-On-Wet Sealer Application
PS21nr 1K Gray Sealer - U.S. National Rule Wet-On-Wet Sealer Application
A P P L I C AT I O N P R O C E D U R E S
Standard Preparation
for Plastic Parts
General This system is used to repair damaged flexible or rigid plastic parts, or to refinish replacement plastic
parts.
Clean all areas to be painted with plastic cleaner. R-M 902 Plastic Prep-Cleaner, then
R-M 909 Final Wipe
Sanding Prepare any areas that are to be painted by scuffing with a Scotchbrite #7447
fine scuff pad.
Cleaning Use an air blow gun to remove all traces of dust and dirt R-M 902 Plastic Prep-Cleaner, then
from the cracks and surfaces of the vehicle. R-M 909 Final Wipe
Pre-prime For bare plastic on flexible plastic parts, apply one coat of R-M 868 1K Plastic Primer
868, 869 or 870. Do not sand. R-M 869 1K Low VOC Adhesion Promoter
R-M 870 High Solids Adhesion Promoter
For bare plastic on semi-rigid or rigid parts, apply one coat for Plastics
of 868, 869 or 870.
Primer Surfacer For flexible parts, apply 2 or 3 coats of primer surfacer 800K 2K Primer Surfacer
mixed with flex additive over any areas that require filling. 846 1K Acrylic Primer
After drying, finish sand with P240 to P320 grit dry, or 892 Flex Agent
P280 to P500 grit wet. See the primer surfacer technical LP20 Epoxy Primer (rigid parts only)
reference sheets for flexed mix ratios.
LP610 Low VOC Primer
For semi-rigid or rigid parts, apply 2 or 3 coats of primer LP620 Low VOC Primer (rigid parts only)
surfacer. After drying, finish sand with P240 to P320 grit 892 Flex Agent
dry, or P280 to P500 grit wet.
Sealer Apply 1 medium wet coat over entire part. Allow to flash 800K 2K Primer Surfacer
for 20 to 30 minutes. See the sealer technical reference LP20 Epoxy Primer (rigid parts only)
sheets for flexed mix ratios. LP610 Low VOC Primer
LP620 Low VOC Primer
LS56 1K Sealer
LS800 2K Sealer
PS21nr 1K Gray Sealer
892 Flex Agent
Standard Preparation
for Plastic Parts
Topcoat All Basecoats and 1K Acrylic / Synthetic Enamel colors may All Limco Topcoats
be used on plastic parts without a flex additive. For all 892 Flex Agent
other topcoats see specific technical data sheet for flex
recommendations.
Clearcoat Apply 2 coats of clear over Limco Basecoat colors. Limco 892 LC4000 Clearcoat
Flex Agent must be added to the Limco clearcoats. See the LC4100 High Solids Clearcoat
clearcoat technical reference sheets for flexed mix ratios. LC4200 Low VOC Clearcoat
LC4500 Express Clear
LC4800 Low 2.0 VOC Express Clear
892 Flex Agent
Notes Always check local VOC laws to ensure that the use of these
Limco products is compliant in your area.
Refer to the appropriate Technical Data Sheet(s) for detailed processing information.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
A P P L I C AT I O N P R O C E D U R E S
Cleaning Remove all traces of oil, grease, welding residue or any 203 Wax and Grease Remover, then
other material with wax and grease remover. Remove 139 Final Wash Cleaner
any traces of rust by sanding, wire wheel, brush or
sandblasting. Remove all traces of paint stripper by
following manufacturer’s instructions.
Zinc or galvanized metal: use coarse scuff pad. (Do not remove zinc or galvanized coating.)
Cleaning Blow off any dust and reclean metal with 139 Final Wash 139 Final Wash Cleaner
Cleaner.
Always check local VOC laws to ensure that the use of these Limco products is compliant in your area.
Refer to the appropriate Technical Data Sheet(s) for detailed processing information.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
A P P L I C AT I O N P R O C E D U R E S
General Use this procedure to repair or refinish OEM finishes or fully cured, sound old paint work.
Clean all areas to be painted with 203 Wax and Grease 203 Wax and Grease Remover, then
Remover, then do a final wipe with 139 Final Wash 139 Final Wash Cleaner
Cleaner.
Sanding Dry sand all painted areas and any body filler areas that will be primed with P240 grit sandpaper. Be
sure to only prime over sanded areas.
Sand any areas that will be topcoated directly with P400 grit or finer wet or P320 grit or finer dry.
Prepare any areas that are to be blended into by compounding and scuffing with a fine scuff pad.
Cleaning Use an air blow gun to remove all traces of dust and dirt
from the cracks and surfaces of the vehicle.
Clean all areas to be painted with pre-paint cleaner 139 139 Final Wash Cleaner
Final Wash Cleaner making sure to remove all residue. Do
not allow pre-paint cleaners to dry on the surface. Apply
wet and then dry with a clean rag.
Notes Always check local VOC laws to ensure that the use of these Limco products is compliant in your area.
Refer to the appropriate Technical Data Sheet(s) for detailed processing information.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
A P P L I C AT I O N P R O C E D U R E S
General Supreme PLUS Basecoat U.S. National Rule VOC is based upon a modified acrylic resin system that can
be blended for the repair of original basecoat/clearcoat finishes.
Pre-prime Apply 1 or 2 coats of precoat primer to all bare metal LP20 Epoxy Primer
areas. Allow sufficient flash time between coats. Do not LP100 Etch Primer
sand. Allow to dry for 30 minutes before applying primer
surfacer.
Primer Surfacer Build up any damaged areas with 2 or 3 coats of primer H1000 1K Waterborne Primer *
surfacer. After drying, sand dry with P320 grit sandpaper 800K 2K Primer Surfacer
or sand wet with P400 grit sandpaper. Apply primer 846 1K Acrylic Primer
surfacer per technical reference sheets. LP20 Epoxy Primer
* Dry sand only and can not be used over LP100. LP610 Low VOC Primer
LP620 Low VOC Primer
Sealer A sealer can improve holdout, maximize adhesion and 800K 2K Primer Surfacer
minimize sand scratch swelling. Apply sealer per technical LP20 Epoxy Primer
reference sheets. LP610 Low VOC Primer
LP620 Low VOC Primer
LS56 1K Sealer
LS800 2K Sealer
PS21nr 1K Gray Sealer
Notes Always check local VOC laws to ensure that the use of these Limco products is compliant in your area.
Refer to the appropriate Technical Data Sheet(s) for detailed processing information.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
A P P L I C AT I O N P R O C E D U R E S
General Supreme PLUS Basecoat Low VOC is based upon a modified acrylic resin system that can be blended for
the repair of original basecoat/clearcoat finishes.
Pre-prime Apply 1 or 2 coats of precoat primer to all bare metal LP20 Epoxy Primer
areas. Allow sufficient flash time between coats. Do not LP100 Etch Primer
sand. Allow to dry for 30 minutes before applying primer
surfacer.
Primer Surfacer Build up any damaged areas with 2 or 3 coats of primer H1000 1K Waterborne Primer *
surfacer. After drying, sand dry with P320 grit sandpaper LP20 Epoxy Primer
or sand wet with P400 grit sandpaper. Apply primer LP610 Low VOC Primer
surfacer per technical reference sheets. LP620 Low VOC Primer
* Dry sand only and can not be used over LP100.
Sealer A sealer can improve holdout, maximize adhesion and LP20 Epoxy Primer
minimize sand scratch swelling. Apply sealer per technical LP610 Low VOC Primer
reference sheets. LP620 Low VOC Primer
Notes Always check local VOC laws to ensure that the use of these Limco products is compliant in your area.
Refer to the appropriate Technical Data Sheet(s) for detailed processing information.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
Coverage 567 sq. ft./gal @ 1.0 mils 644 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 60 minutes with LH810; 90 minutes with LH810;
1.5 - 2 hours with LH820 2.5 hours with LH820
140°F/60°C 20 minutes 20 minutes
Infra red short wave N/A N/A
Infra red medium wave N/A N/A
Sanding:
Wet by Hand P320 - P400 grit P320 - P400 grit
VOC as applied ≤ 580 gms/liter (≤ 4.8 lbs/gal) ≤ 580 gms/liter (≤ 4.8 lbs/gal)
Comments
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
Coverage 573 sq. ft./gal @ 1.0 mils 652 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 60 minutes with LHF; 90 minutes with LHF;
1.5 - 2 hours with LHS 2.5 hours with LHS
140°F/60°C 20 minutes 20 minutes
Infra red short wave N/A N/A
Infra red medium wave N/A N/A
Sanding:
Wet by Hand P320 - P400 grit P320 - P400 grit
VOC as applied ≤ 580 gms/liter (≤ 4.8 lbs/gal) ≤ 580 gms/liter (≤ 4.8 lbs/gal)
Comments
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
Coverage 585 sq. ft./gal @ 1.0 mils 648 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 15 - 30 minutes 15 - 30 minutes
140°F/60°C N/A N/A
Infra red short wave N/A N/A
Infra red medium wave N/A N/A
Sanding:
Wet by Hand N/A N/A
VOC as applied ≤ 580 gms/liter (≤ 4.8 lbs/gal) ≤ 580 gms/liter (≤ 4.8 lbs/gal)
Comments
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
Coverage 631 sq. ft./gal @ 1.0 mils 689 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 15 - 30 minutes 15 - 30 minutes
140°F/60°C N/A N/A
Infra red short wave N/A N/A
Infra red medium wave N/A N/A
Sanding:
Wet by Hand N/A N/A
Comments
Click on logo to return to Table of Contents
U N D E R C O AT S
Description: Limco 846 1K Acrylic Primer is a non-settling, fast drying, easy sanding, flexible primer that meets
the U.S. National Rule and provides excellent adhesion plus good color hold-out.
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
846 is a high filling, fast sanding 1K lacquer primer. Best results are obtained when thinner coats,
with 5 - 10 minutes flash between coats, are observed. Excessive film builds of lacquer primer can
lead to soft topcoats or premature film failures.
Drying:
68°F/20°C 20 minutes
140°F/60°C N/A
Infra red short wave N/A
Infra red medium wave N/A
Sanding:
Wet by Hand N/A
Comments
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
Description: Limco H1000 1K Waterborne Primer is a grey, 1K Low VOC Waterborne System that is fast drying,
easy sanding and provides excellent adhesion with good color holdout.
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Topcoats: Supreme PLUS Acrylic 1K Single Stage (U.S. National Rule and Low VOC)
Supreme PLUS Acrylic 2K Single Stage (U.S. National Rule and Low VOC)
Supreme PLUS Urethane Single Stage (U.S. National Rule and Low VOC)
Supreme PLUS Basecoat (U.S. National Rule and Low VOC)
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
Shelf Life - 12 months
Keep from freezing.
Store at temperatures 40°F - 105°F / 5°C - 40°C.
Dry sand only. DO NOT wet sand H1000 1K Waterborne Primer.
Application 2 - 3 coats
Drying:
68°F/20°C 30 minutes
140°F/60°C N/A
Infra red short wave N/A
Infra red medium wave N/A
Sanding:
Wet by Hand N/A
Comments
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
Description: Limco LP20 Epoxy Primer is a two part epoxy primer for use as a primer under 800K, 846, PS21nr,
LS800 or LS56. LP20 offers excellent adhesion and corrosion protection when used over steel,
aluminum, zinc coated or galvanized metals. LP20 can be applied over cured, cleaned and sanded
paint finishes (except acrylic lacquers).
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
Drying:
68°F/20°C 15 - 30 minutes
140°F/60°C N/A
Infra red short wave N/A
Infra red medium wave N/A
Sanding:
Wet by Hand N/A
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
Description: LP20 Epoxy Primer is a two part epoxy primer for use as a primer under H1000, LP610 or LP620.
LP20 offers excellent adhesion and corrosion protection when used over steel, aluminum, zinc
coated or galvanized metals. LP20 can be applied over cured, cleaned and sanded paint finishes
(except acrylic lacquers).
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Topcoats: Supreme PLUS Low VOC Acrylic 1K Single Stage 340 gms/liter (2.8 lbs/gal) VOC
Supreme PLUS Low VOC Acrylic 1K Single Stage 420 gms/liter (3.5 lbs/gal) VOC
Supreme PLUS Low VOC Acrylic 2K Single Stage 340 gms/liter (2.8 lbs/gal) VOC
Supreme PLUS Low VOC Acrylic 2K Single Stage 420 gms/liter (3.5 lbs/gal) VOC
Supreme PLUS Low VOC Urethane Single Stage 340 gms/liter (2.8 lbs/gal) VOC
Supreme PLUS Low VOC Urethane Single Stage 420 gms/liter (3.5 lbs/gal) VOC
Supreme PLUS Low VOC Basecoat 420 gms/liter (3.5 lbs/gal) VOC
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
Drying:
68°F/20°C 15 - 30 minutes
140°F/60°C N/A
Infra red short wave N/A
Infra red medium wave N/A
Sanding:
Wet by Hand N/A
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
Description: Limco LP20 Epoxy Primer is a two part epoxy primer for use as a Primer Surfacer. LP20 offers excellent
adhesion and corrosion protection when used over steel, aluminum, zinc coated or galvanized
metals. LP20 can be applied over cured, cleaned and sanded paint finishes (except acrylic lacquers).
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
Drying:
68°F/20°C 3 hours
140°F/60°C 30 - 35 minutes
Infra red short wave N/A
Infra red medium wave N/A
Sanding:
Wet by Hand P400 - P600 grit
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
Description: Limco LP20 Epoxy Primer is a two part epoxy primer for use as a Primer Surfacer. LP20 offers excellent
adhesion and corrosion protection when used over steel, aluminum, zinc coated or galvanized
metals. LP20 can be applied over cured, cleaned and sanded paint finishes (except acrylic lacquers).
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Topcoats: Supreme PLUS Low VOC Acrylic 1K Single Stage 340 gms/liter (2.8 lbs/gal) VOC
Supreme PLUS Low VOC Acrylic 1K Single Stage 420 gms/liter (3.5 lbs/gal) VOC
Supreme PLUS Low VOC Acrylic 2K Single Stage 340 gms/liter (2.8 lbs/gal) VOC
Supreme PLUS Low VOC Acrylic 2K Single Stage 420 gms/liter (3.5 lbs/gal) VOC
Supreme PLUS Low VOC Urethane Single Stage 340 gms/liter (2.8 lbs/gal) VOC
Supreme PLUS Low VOC Urethane Single Stage 420 gms/liter (3.5 lbs/gal) VOC
Supreme PLUS Low VOC Basecoat 420 gms/liter (3.5 lbs/gal) VOC
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
Drying:
68°F/20°C 6 hours
140°F/60°C 30 - 35 minutes
Infra red short wave N/A
Infra red medium wave N/A
Sanding:
Wet by Hand P400 - P600 grit
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
Description: Limco LP20 Epoxy Primer is a two part epoxy primer for use as a wet-on-wet sealer under Limco
Supreme PLUS topcoats. LP20 can be applied over cured, cleaned and sanded paint finishes (except
acrylic lacquers).
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
5 - 10 minutes 5 - 10 minutes
Flash-off time @ 68°F/20°C
between coats between coats
Coverage 697 sq. ft./gal @ 1.0 mils 688 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 45 minutes before topcoating 45 minutes before topcoating
with Limco with Limco
140°F/60°C N/A N/A
Infra red short wave N/A N/A
Infra red medium wave N/A N/A
Sanding:
Wet by Hand N/A N/A
VOC as applied ≤ 550 gms/liter (≤ 4.6 lbs/gal) ≤ 550 gms/liter (≤ 4.6 lbs/gal)
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
Description: Limco LP20 Epoxy Primer is a two part epoxy primer for use as a wet-on-wet sealer under Limco
Supreme PLUS topcoats. LP20 can be applied over cured, cleaned and sanded paint finishes (except
acrylic lacquers).
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Topcoats: Supreme PLUS Low VOC Acrylic 1K Single Stage 340 gms/liter (2.8 lbs/gal) VOC
Supreme PLUS Low VOC Acrylic 1K Single Stage 420 gms/liter (3.5 lbs/gal) VOC
Supreme PLUS Low VOC Acrylic 2K Single Stage 340 gms/liter (2.8 lbs/gal) VOC
Supreme PLUS Low VOC Acrylic 2K Single Stage 420 gms/liter (3.5 lbs/gal) VOC
Supreme PLUS Low VOC Urethane Single Stage 340 gms/liter (2.8 lbs/gal) VOC
Supreme PLUS Low VOC Urethane Single Stage 420 gms/liter (3.5 lbs/gal) VOC
Supreme PLUS Low VOC Basecoat 420 gms/liter (3.5 lbs/gal) VOC
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
Drying:
68°F/20°C 45 minutes before topcoating with Limco
140°F/60°C N/A
Infra red short wave N/A
Infra red medium wave N/A
Sanding:
Wet by Hand N/A
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
Description: Limco LP100 Etch Primer is chromate free and has excellent adhesion properties that work equally
well on steel, aluminum and galvanized steel. When applied over bare steel, LP100 is an effective
rust inhibitor. Limco LP100 can be primed over with any approved Limco undercoat except H1000.
Limco LP100 should also not be used under waterborne primers or peroxide-cured body fillers.
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
Drying:
68°F/20°C 15 minutes
140°F/60°C N/A
Infra red short wave N/A
Infra red medium wave N/A
Sanding:
Wet by Hand N/A
Comments Appropriate undercoat must be applied on top of LP100 within 4 hours of application.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
Description: Limco LP100 Etch Primer is chromate free and has excellent adhesion properties that work equally
well on steel, aluminum and galvanized steel. When applied over bare steel, LP100 is an effective
rust inhibitor. Limco LP100 can be primed over with any approved Limco undercoat except H1000.
Limco LP100 should also not be used under waterborne primers or peroxide-cured body fillers.
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
Drying:
68°F/20°C 15 minutes
140°F/60°C N/A
Infra red short wave N/A
Infra red medium wave N/A
Sanding:
Wet by Hand N/A
Comments Appropriate undercoat must be applied on top of LP100 within 4 hours of application.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
Description: Limco LP610 Low VOC Primer is a quick cure, sandable primer that provides good sand scratch filling
with excellent adhesion and topcoat holdout. It is a 2.1 VOC compliant performance primer that
provides good filling properties.
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Topcoats: Supreme PLUS Low VOC Acrylic 1K Single Stage 340 gms/liter (2.8 lbs/gal) VOC
Supreme PLUS Low VOC Acrylic 1K Single Stage 420 gms/liter (3.5 lbs/gal) VOC
Supreme PLUS Low VOC Acrylic 2K Single Stage 340 gms/liter (2.8 lbs/gal) VOC
Supreme PLUS Low VOC Acrylic 2K Single Stage 420 gms/liter (3.5 lbs/gal) VOC
Supreme PLUS Low VOC Urethane Single Stage 340 gms/liter (2.8 lbs/gal) VOC
Supreme PLUS Low VOC Urethane Single Stage 420 gms/liter (3.5 lbs/gal) VOC
Supreme PLUS Low VOC Basecoat 420 gms/liter (3.5 lbs/gal) VOC
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
Use an adhesion promoter when refinishing raw plastic parts.
Coverage 678 sq. ft./gal @ 1.0 mils 763 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 60 - 90 minutes 90 - 120 minutes
140°F/60°C 30 minutes; 30 minutes;
allow 10 minutes flash before force dry allow 10 minutes flash before force dry
Infra red short wave 5 - 7 minutes 6 - 8 minutes
Infra red medium wave N/A N/A
Sanding:
Wet by Hand P400 grit P400 grit
VOC as applied ≤ 250 gms/liter (≤ 2.1 lbs/gal) ≤ 250 gms/liter (≤ 2.1 lbs/gal)
Comments
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
Description: Limco LP610 Low VOC Primer is a quick cure, sandable primer that provides good sand scratch filling
with excellent adhesion and topcoat holdout. It is a 2.1 VOC compliant performance primer that
provides good filling properties.
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Topcoats: Supreme PLUS Low VOC Acrylic 1K Single Stage 340 gms/liter (2.8 lbs/gal) VOC
Supreme PLUS Low VOC Acrylic 1K Single Stage 420 gms/liter (3.5 lbs/gal) VOC
Supreme PLUS Low VOC Acrylic 2K Single Stage 340 gms/liter (2.8 lbs/gal) VOC
Supreme PLUS Low VOC Acrylic 2K Single Stage 420 gms/liter (3.5 lbs/gal) VOC
Supreme PLUS Low VOC Urethane Single Stage 340 gms/liter (2.8 lbs/gal) VOC
Supreme PLUS Low VOC Urethane Single Stage 420 gms/liter (3.5 lbs/gal) VOC
Supreme PLUS Low VOC Basecoat 420 gms/liter (3.5 lbs/gal) VOC
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
Use an adhesion promoter when refinishing raw plastic parts.
Coverage 574 sq. ft./gal @ 1.0 mils 667 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 30 minutes flash before topcoating 30 minutes flash before topcoating
140°F/60°C N/A N/A
Infra red short wave N/A N/A
Infra red medium wave N/A N/A
Sanding:
Wet by Hand N/A N/A
VOC as applied ≤ 250 gms/liter (≤ 2.1 lbs/gal) ≤ 250 gms/liter (≤ 2.1 lbs/gal)
Comments
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
Description: Limco LP620 Low VOC Primer in this National Rule presentation is a quick cure, sandable primer
that provides good sand scratch filling with excellent adhesion and topcoat holdout. It is a National
Rule compliant performance primer that provides good filling properties.
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
Use an adhesion promoter when refinishing raw plastic parts.
Drying:
68°F/20°C 60 - 90 minutes
140°F/60°C 30 - 40 minutes; allow 10 minutes flash before force drying.
Infra red short wave 5 - 7 minutes
Infra red medium wave N/A
Sanding:
Wet by Hand P400 grit
Comments
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
Description: Limco LP620 Low VOC Primer is a quick cure, sandable primer that provides good sand scratch filling
with excellent adhesion and topcoat holdout. It is a 2.1 VOC compliant performance primer that
provides good filling properties.
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Topcoats: Supreme PLUS Low VOC Acrylic 1K Single Stage 340 gms/liter (2.8 lbs/gal) VOC
Supreme PLUS Low VOC Acrylic 1K Single Stage 420 gms/liter (3.5 lbs/gal) VOC
Supreme PLUS Low VOC Acrylic 2K Single Stage 340 gms/liter (2.8 lbs/gal) VOC
Supreme PLUS Low VOC Acrylic 2K Single Stage 420 gms/liter (3.5 lbs/gal) VOC
Supreme PLUS Low VOC Urethane Single Stage 340 gms/liter (2.8 lbs/gal) VOC
Supreme PLUS Low VOC Urethane Single Stage 420 gms/liter (3.5 lbs/gal) VOC
Supreme PLUS Low VOC Basecoat 420 gms/liter (3.5 lbs/gal) VOC
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
Use an adhesion promoter when refinishing raw plastic parts.
Drying:
68°F/20°C 60 - 90 minutes
140°F/60°C 30 - 40 minutes; allow 10 minutes flash before force drying.
Infra red short wave 5 - 7 minutes
Infra red medium wave N/A
Sanding:
Wet by Hand P400 grit
Comments
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
Description: Limco LP620 Low VOC Primer in this National Rule presentation is a quick cure, sandable primer
that provides good sand scratch filling with excellent adhesion and topcoat holdout. It is a National
Rule compliant performance primer that provides good filling properties.
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
Use an adhesion promoter when refinishing raw plastic parts.
Gravity gun nozzle HVLP 1.3 - 1.5 mm 1.3 - 1.5 mm 1.3 - 1.5 mm
Application 1 medium wet coat 1 medium wet coat 1 medium wet coat
Film build 1.0 - 1.5 mils 1.0 - 1.5 mils 1.0 - 1.5 mils
Coverage 597 sq. ft./gal @ 1.0 mils 651 sq. ft./gal @ 1.0 mils 608 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 30 minutes flash before 30 minutes flash before 30 minutes flash before
topcoating topcoating topcoating
140°F/60°C N/A N/A N/A
Infra red short wave N/A N/A N/A
Infra red medium wave N/A N/A N/A
Sanding:
Wet by Hand N/A N/A N/A
Comments
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
Description: Limco LP620 Low VOC Primer is a 2.1 VOC compliant performance sealer that provides good filling
properties and quick drying with good melt-in and topcoat holdout..
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Topcoats: Supreme PLUS Low VOC Acrylic 1K Single Stage 340 gms/liter (2.8 lbs/gal) VOC
Supreme PLUS Low VOC Acrylic 1K Single Stage 420 gms/liter (3.5 lbs/gal) VOC
Supreme PLUS Low VOC Acrylic 2K Single Stage 340 gms/liter (2.8 lbs/gal) VOC
Supreme PLUS Low VOC Acrylic 2K Single Stage 420 gms/liter (3.5 lbs/gal) VOC
Supreme PLUS Low VOC Urethane Single Stage 340 gms/liter (2.8 lbs/gal) VOC
Supreme PLUS Low VOC Urethane Single Stage 420 gms/liter (3.5 lbs/gal) VOC
Supreme PLUS Low VOC Basecoat 420 gms/liter (3.5 lbs/gal) VOC
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
Use an adhesion promoter when refinishing raw plastic parts.
Coverage 616 sq. ft./gal @ 1.0 mils 668 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 30 minutes flash before topcoating 30 minutes flash before topcoating
140°F/60°C N/A N/A
Infra red short wave N/A N/A
Infra red medium wave N/A N/A
Sanding:
Wet by Hand N/A N/A
VOC as applied ≤ 250 gms/liter (≤ 2.1 lbs/gal) ≤ 250 gms/liter (≤ 2.1 lbs/gal)
Comments
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
LS56 1K Sealer
U.S. National Rule Wet-On-Wet Sealer Application
Description: Limco LS56 1K Sealer is a fast drying sealer that provides excellent adhesion with good topcoat
color hold out.
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
LS56 1K Sealer
U.S. National Rule Wet-On-Wet Sealer Application
Mixing ratio: 2:1
Sealer 2 parts LS56
Reducer 1 part LR21
Drying:
68°F/20°C 30 minutes
140°F/60°C N/A
Infra red short wave N/A
Infra red medium wave N/A
Sanding:
Wet by Hand N/A
Comments
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
LS800 2K Sealer
U.S. National Rule Wet-On-Wet Sealer Application
Description: The LS800 2K Sealer is a tintable wet-on-wet sealer that dries quickly and provides excellent
adhesion. LS800 2K Sealer can be tinted using Limco Supreme PLUS bases.
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
Do not use mixed color to tint LS800. Tint LS800 with LA bases only.
Do not force dry LS800, wet-on- wet application.
LS800 2K Sealer
U.S. National Rule Wet-On-Wet Sealer Application
Untinted Tinted
Mixing ratio: 4:1:2 4:1:1:2
Primer 4 parts LS800 4 parts LS800
Color — 1 part LA Base
Hardener 1 part LHF or LHM 1 part LHF or LHM
Reducer 2 parts LR10, LR11, LR12 or LR13 2 parts LR10, LR11, LR12 or LR13
Coverage 590 sq. ft./gal @ 1.0 mils 597 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 15 minutes (no longer than 30 minutes (no longer than
3 hours before topcoat) 4 hours before topcoat)
140°F/60°C N/A N/A
Infra red short wave N/A N/A
Infra red medium wave N/A N/A
Sanding:
Wet by Hand N/A N/A
VOC as applied ≤ 550 gms/liter (≤ 4.6 lbs/gal) ≤ 550 gms/liter (≤ 4.6 lbs/gal)
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
U N D E R C O AT S
Description: Limco PS21nr 1K Gray Sealer improves color hold-out and eliminates sand scratch swelling. This
sealer is non-sanding, fast drying and ensures excellent adhesion.
NOTES: On Galvanized Steel and Aluminum, make sure sanding is not so vigorous that it removes the galvanized coating.
With the second cleaning, make sure all residue is removed. Pay special attention when cleaning Galvanized Steel and
Aluminum.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
Drying:
68°F/20°C 20 minutes
140°F/60°C N/A
Infra red short wave N/A
Infra red medium wave N/A
Sanding:
Wet by Hand N/A
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
T O P C O AT S
Supreme PLUS
Acrylic 1K Single Stage
U.S. National Rule VOC
Description: Limco Supreme PLUS U.S. National Rule Topcoat is a specially formulated Acrylic 1K Single Stage
system designed to meet the rigorous demands of Refinish, Commercial Vehicle, Agricultural
and Fleet markets. Limco Supreme PLUS U.S. National Rule Acrylic 1K Single Stage Topcoat dries
quickly to a dust-free surface with excellent flow and leveling, good hiding and good gloss.
Substrates prepared
for topcoating: Finish Sanding
Well cured old paint work P500 grit
Primer Surfacer 800K P320 - P500 grit
Primer Surfacer 846 P320 - P500 grit
Primer Surfacer LP20 P320 - P500 grit
Primer Surfacer LP620 P320 - P500 grit
Primer Sealer LP20 Sanding not required
Primer Sealer LP620 Sanding not required
Primer Sealer LS56 Sanding not required
Primer Sealer LS800 Sanding not required
Primer Sealer PS21NR Sanding not required
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
To retrieve color information from BASF color retrieval software, use paint line SA1K.
For custom Supreme PLUS Acrylic 1K (600 gms/liter) colors, the color (LA, LIB, G bases) must be
mixed 1 part to 1 part of LA4999 by volume prior to addition of reducer.
OPTIONAL: For a more durable finish, Limco Hardener LHF, LHM or LHS may be added at a ratio
of 10:1 with 1 part of reducer. Caution: Lighter colors may yellow with the addition of hardener.
Adding hardener will result in a four hour pot life.
US Rev. 11/1/16
T E C H N I C A L D A T A
Supreme PLUS
Acrylic 1K Single Stage
U.S. National Rule VOC
Mixing ratio: 8:1
Color 8 parts Color
Reducer 1 part LR10, LR11, LR12, LR13 or LR15
Drying:
68°F/20°C 30 - 45 minutes dust free;
2 - 4 hours tack free
140°F/60°C 30 minutes
Infra red short wave N/A
Infra red medium wave N/A
Sanding:
Wet by Hand N/A
Comments Shake new tinting bases for 15 minutes using a mechanical paint shaker before placing
on a mixing machine.
Tinting bases on a mixing machine need to be agitated for 15 minutes at the start of
the work day and every 4 hours during the day to ensure good color matching.
For areas requiring recoating four or more hours after application:
Scuff with a fine scuff pad (Scotchbrite #7447).
Cleaning: Use an air blow gun to remove all traces of dust and dirt from the cracks and
surfaces of the vehicle.
Clean all areas to be painted with 139 Final Wipe Cleaner.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
T O P C O AT S
Supreme PLUS
Low VOC Acrylic 1K Single Stage
340 gms/liter (2.8 lbs/gal) VOC
420 gms/liter (3.5 lbs/gal) VOC
Description: Limco Supreme PLUS Low VOC Topcoat is a specially formulated Acrylic 1K Single Stage system
designed to meet the rigorous demands of Refinish, Commercial Vehicle, Agricultural and Fleet
markets. Limco Supreme PLUS Low VOC Acrylic 1K Single Stage Topcoat dries quickly to a dust-free
surface with excellent flow and leveling, good hiding and good gloss.
Substrates prepared
for topcoating: Finish Sanding
Well cured old paint work P500 grit
Primer Surfacer H1000 P320 - P500 grit (dry sand only)
Primer Surfacer LP20 P320 - P500 grit
Primer Surfacer LP610 P320 - P500 grit
Primer Surfacer LP620 P320 - P500 grit
Primer Sealer LP20 Sanding not required
Primer Sealer LP610 Sanding not required
Primer Sealer LP620 Sanding not required
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
To retrieve color information from BASF color retrieval software, use paint line SA1V.
For custom Supreme PLUS Low VOC Acrylic 1K Single Stage colors, the color (LA, LIB, G bases) must
be mixed 1 part to 2.5 parts of LA4899 by volume prior to addition of reducer.
OPTIONAL: For a more durable finish, Limco Low VOC Hardener LH601, LH604 or LH606 may be
added at a ratio of 10:1 with 1 part of reducer. Caution: Lighter colors may yellow with the addition
of hardener. Adding hardener will result in a four hour pot life.
US Rev. 11/1/16
T E C H N I C A L D A T A
Supreme PLUS
Low VOC Acrylic 1K Single Stage
340 gms/liter (2.8 lbs/gal) VOC
420 gms/liter (3.5 lbs/gal) VOC
340 gms/liter (2.8 lbs/gal) VOC 420 gms/liter (3.5 lbs/gal) VOC
Mixing ratio: 8:1 8:1
Color 8 parts Color 8 parts Color
Reducer 1 part LR21 or LR25 1 part LR10, LR11, LR12, LR13 or LR15
(may use up to 2 parts of reducer)
Coverage 524 - 570 sq. ft./gal @ 1.0 mils 524 - 570 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 60 - 90 minutes dust free; 60 - 90 minutes dust free;
3 - 5 hours tack free 3 - 5 hours tack free
140°F/60°C 30 minutes 30 minutes
Infra red short wave N/A N/A
Infra red medium wave N/A N/A
Sanding:
Wet by Hand N/A N/A
VOC as applied ≤ 340 gms/liter (≤ 2.8 lbs/gal) ≤ 420 gms/liter (≤ 3.5 lbs/gal)
Comments Shake new tinting bases for 15 minutes using a mechanical paint shaker before placing
on a mixing machine.
Tinting bases on a mixing machine need to be agitated for 15 minutes at the start of
the work day and every 4 hours during the day to ensure good color matching.
For areas requiring recoating four or more hours after application:
Scuff with a fine scuff pad (Scotchbrite #7447).
Cleaning: Use an air blow gun to remove all traces of dust and dirt from the cracks and
surfaces of the vehicle.
Clean all areas to be painted with 909 Final Wipe Cleaner.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
T O P C O AT S
Supreme PLUS
Acrylic 2K Single Stage
U.S. National Rule VOC
Description: Limco Supreme PLUS U.S. National Rule Topcoat is a specially formulated Acrylic 2K Single Stage
system designed to meet the rigorous demands of Refinish, Commercial Vehicle, Agricultural and
Fleet markets. Limco Supreme PLUS U.S. National Rule Acrylic 2K Single Stage Topcoat dries quickly
to a dust-free surface with excellent flow and leveling, good hiding and mirror-like gloss. The
Supreme PLUS U.S. National Rule Acrylic 2K Single Stage Topcoat film is also chemically resistant
and has superior hardness.
Substrates prepared
for topcoating: Finish Sanding
Well cured old paint work P500 grit
Primer Surfacer 800K P320 - P500 grit
Primer Surfacer 846 P320 - P500 grit
Primer Surfacer LP20 P320 - P500 grit
Primer Surfacer LP620 P320 - P500 grit
Primer Sealer LP20 Sanding not required
Primer Sealer LP620 Sanding not required
Primer Sealer LS56 Sanding not required
Primer Sealer LS800 Sanding not required
Primer Sealer PS21NR Sanding not required
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
To retrieve color information from BASF color retrieval software, use paint line SA2K.
For custom Supreme PLUS Acrylic 2K (600 gms/liter) colors, the color (LA, LIB, G bases) must be
mixed 1 part to 1 part of LA3899 by volume prior to addition of hardener and reducer.
US Rev. 11/1/16
T E C H N I C A L D A T A
Supreme PLUS
Acrylic 2K Single Stage
U.S. National Rule VOC
Mixing ratio: 8:1:1
Color 8 parts Color
Hardener 1 part LHF, LHM or LHS
Reducer 1 part LR10, LR11, LR12, LR13 or LR15
Drying:
68°F/20°C 30 - 45 minutes dust free; 4 - 6 hours tack free
140°F/60°C 30 minutes
Infra red short wave N/A
Infra red medium wave N/A
Sanding:
Wet by Hand N/A
Comments Shake new tinting bases for 15 minutes using a mechanical paint shaker before placing
on a mixing machine.
Tinting bases on a mixing machine need to be agitated for 15 minutes at the start of
the work day and every 4 hours during the day to ensure good color matching.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
T O P C O AT S
Supreme PLUS
Low VOC Acrylic 2K Single Stage
340 gms/liter (2.8 lbs/gal) VOC
420 gms/liter (3.5 lbs/gal) VOC
Description: Limco Supreme PLUS Low VOC Topcoat is a specially formulated Acrylic 2K Single Stage system
designed to meet the rigorous demands of Refinish, Commercial Vehicle, Agricultural and Fleet
markets. Limco Supreme PLUS Low VOC Acrylic 2K Single Stage Topcoat dries quickly to a dust-free
surface with excellent flow and leveling, good hiding and mirror-like gloss. The Supreme PLUS Low
VOC Acrylic 2K Single Stage Topcoat film is also chemically resistant and has superior hardness.
Substrates prepared
for topcoating: Finish Sanding
Well cured old paint work P500 grit
Primer Surfacer H1000 P320 - P500 grit (dry sand only)
Primer Surfacer LP20 P320 - P500 grit
Primer Surfacer LP610 P320 - P500 grit
Primer Surfacer LP620 P320 - P500 grit
Primer Sealer LP20 Sanding not required
Primer Sealer LP610 Sanding not required
Primer Sealer LP620 Sanding not required
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
To retrieve color information from BASF color retrieval software, use paint line SA2V.
For custom Supreme PLUS Low VOC Acrylic 2K Single Stage colors, the color (LA, LIB, G bases) must
be mixed 1 part to 2.5 parts of LA3899 by volume prior to addition of hardener and reducer.
US Rev. 11/1/16
T E C H N I C A L D A T A
Supreme PLUS
Low VOC Acrylic 2K Single Stage
340 gms/liter (2.8 lbs/gal) VOC
420 gms/liter (3.5 lbs/gal) VOC
340 gms/liter (2.8 lbs/gal) VOC 420 gms/liter (3.5 lbs/gal) VOC
Mixing ratio: 8:1:1 8:1:1
Color 8 parts Color 8 parts Color
Hardener 1 part LH601, LH604 or LH606 1 part LH601, LH604 or LH606
Reducer 1 part LR21 or LR25 1 part LR10, LR11, LR12, LR13 or LR15
(may use up to 2 parts of reducer)
Coverage 556 - 600 sq. ft./gal @ 1.0 mils 556 - 600 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C LH601: 25 - 30 minutes dust free; 35 - 45 minutes dust free;
2 hours tack free (depending on reducer) 4 - 6 hours tack free
LH604: 60 - 70 minutes dust free;
4 hours tack free (depending on reducer)
140°F/60°C 30 minutes 30 minutes
Infra red short wave N/A N/A
Infra red medium wave N/A N/A
Sanding:
Wet by Hand N/A N/A
VOC as applied ≤ 340 gms/liter (≤ 2.8 lbs/gal) ≤ 420 gms/liter (≤ 3.5 lbs/gal)
Comments Shake new tinting bases for 15 minutes using a mechanical paint shaker before placing
on a mixing machine.
Tinting bases on a mixing machine need to be agitated for 15 minutes at the start of
the work day and every 4 hours during the day to ensure good color matching.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
T O P C O AT S
Supreme PLUS
Urethane Single Stage
U.S. National Rule VOC with LA2799
Description: Limco Supreme PLUS U.S. National Rule Topcoat is a specially formulated 2K Urethane Single Stage
system designed to meet the rigorous demands of Refinish, Commercial Vehicle, Agricultural and
Fleet markets. Limco Supreme PLUS U.S. National Rule Urethane Single Stage Topcoat dries quickly
to a dust-free surface with excellent flow and leveling, good hiding and mirror-like gloss. The
Supreme PLUS U.S. National Rule Urethane Single Stage Topcoat film is also chemically resistant
and has superior hardness.
Substrates prepared
for topcoating: Finish Sanding
Well cured old paint work P500 grit
Primer Surfacer 800K P320 - P500 grit
Primer Surfacer 846 P320 - P500 grit
Primer Surfacer LP20 P320 - P500 grit
Primer Surfacer LP620 P320 - P500 grit
Primer Sealer LP20 Sanding not required
Primer Sealer LP620 Sanding not required
Primer Sealer LS56 Sanding not required
Primer Sealer LS800 Sanding not required
Primer Sealer PS21NR Sanding not required
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
To retrieve color information from BASF color retrieval software, use paint line SUNR.
For custom Supreme PLUS Urethane Single Stage (U.S. National Rule) colors, the color (LA, LIB,
G bases) must be mixed 2 parts to 1 part of LA2799 by volume prior to addition of hardener and
reducer.
US Rev. 11/1/16
T E C H N I C A L D A T A
Supreme PLUS
Urethane Single Stage
U.S. National Rule VOC with LA2799
Flexed
Coverage 603 - 626 sq. ft./gal @ 1.0 mils 770 - 791 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 3 - 4 hours dust free; 3 - 4 hours dust free;
8 - 10 hours to handle 8 - 10 hours to handle
140°F/60°C 30 minutes 30 minutes
Infra red short wave N/A N/A
Infra red medium wave N/A N/A
Sanding:
Wet by Hand N/A N/A
VOC as applied ≤ 600 gms/liter (≤ 5.0 lbs/gal) ≤ 600 gms/liter (≤ 5.0 lbs/gal)
Comments Shake new tinting bases for 15 minutes using a mechanical paint shaker before placing
on a mixing machine.
Tinting bases on a mixing machine need to be agitated for 15 minutes at the start of
the work day and every 4 hours during the day to ensure good color matching.
When using LHM in cool temperatures, use up to 1.0 oz of Jet95 Accelerator per ready
for use gallon.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
T O P C O AT S
Supreme PLUS
Urethane Single Stage
U.S. National Rule VOC with LA2999
Description: Limco Supreme PLUS U.S. National Rule Topcoat is a specially formulated 2K Urethane Single Stage
system designed to meet the rigorous demands of Refinish, Commercial Vehicle, Agricultural and
Fleet markets. Limco Supreme PLUS U.S. National Rule Urethane Single Stage Topcoat dries quickly
to a dust-free surface with excellent flow and leveling, good hiding and mirror-like gloss. The
Supreme PLUS U.S. National Rule Urethane Single Stage Topcoat film is also chemically resistant
and has superior hardness.
Substrates prepared
for topcoating: Finish Sanding
Well cured old paint work P500 grit
Primer Surfacer 800K P320 - P500 grit
Primer Surfacer 846 P320 - P500 grit
Primer Surfacer LP20 P320 - P500 grit
Primer Surfacer LP620 P320 - P500 grit
Primer Sealer LP20 Sanding not required
Primer Sealer LP620 Sanding not required
Primer Sealer LS56 Sanding not required
Primer Sealer LS800 Sanding not required
Primer Sealer PS21NR Sanding not required
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
To retrieve color information from BASF color retrieval software, use paint line SUSS.
For custom Supreme PLUS Urethane Single Stage (U.S. National Rule) colors, the color (LA, LIB,
G bases) must be mixed 1 part to 1 part of LA2999 by volume prior to addition of hardener and
reducer.
For larger areas, use LA2999S for slower application properties.
US Rev. 11/1/16
T E C H N I C A L D A T A
Supreme PLUS
Urethane Single Stage
U.S. National Rule VOC with LA2999
Flexed
Coverage 575 - 625 sq. ft./gal @ 1.0 mils 700 - 750 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 1 - 1.5 hours 1 - 1.5 hours
with LA2999S: 3 - 4 hours dust free; with LA2999S: 3 - 4 hours dust free;
8 hours to handle 8 hours to handle
140°F/60°C 30 minutes 30 minutes
Infra red short wave N/A N/A
Infra red medium wave N/A N/A
Sanding:
Wet by Hand N/A N/A
VOC as applied ≤ 600 gms/liter (≤ 5.0 lbs/gal) ≤ 600 gms/liter (≤ 5.0 lbs/gal)
Comments Shake new tinting bases for 15 minutes using a mechanical paint shaker before placing
on a mixing machine.
Tinting bases on a mixing machine need to be agitated for 15 minutes at the start of
the work day and every 4 hours during the day to ensure good color matching.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
T O P C O AT S
Supreme PLUS
Low VOC Urethane Single Stage
340 gms/liter (2.8 lbs/gal) VOC with LA2799
Description: Limco Supreme PLUS Topcoat 340 gms/liter (2.8 lbs/gal) VOC is a specially formulated 2K Urethane
Single Stage system designed to meet the rigorous demands of Refinish, Commercial Vehicle,
Agricultural and Fleet markets. Limco Supreme PLUS Urethane Single Stage Topcoat 340 gms/liter
(2.8 lbs/gal) VOC dries quickly to a dust-free surface with excellent flow and leveling, good hiding
and mirror-like gloss. The Supreme PLUS Urethane Single Stage Topcoat 340 gms/liter (2.8 lbs/gal)
VOC film is also chemically resistant and has superior hardness.
Substrates prepared
for topcoating: Finish Sanding
Well cured old paint work P500 grit
Primer Surfacer H1000 P320 - P500 grit (dry sand only)
Primer Surfacer LP20 P320 - P500 grit
Primer Surfacer LP610 P320 - P500 grit
Primer Surfacer LP620 P320 - P500 grit
Primer Sealer LP20 Sanding not required
Primer Sealer LP610 Sanding not required
Primer Sealer LP620 Sanding not required
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
To retrieve color information from BASF color retrieval software, use paint line SU28.
For custom Supreme PLUS Low VOC Urethane Single Stage (340 gms/liter) colors, the color (LA,
LIB, G bases) must be mixed 1 part to 1 part of LA2799 by volume prior to addition of hardener
and reducer.
US Rev. 11/1/16
T E C H N I C A L D A T A
Supreme PLUS
Low VOC Urethane Single Stage
340 gms/liter (2.8 lbs/gal) VOC with LA2799
Flexed
Mixing ratio: 4:1:2 8:3:2:2
Color 4 parts Color 8 parts Color
Hardener 1 part LH601, LH604 or LH606 3 parts LH601, LH604 or LH606
Flex Agent — 2 parts 892
Reducer 2 parts LR21 or LR25 2 parts LR21 or LR25
Coverage 661 - 678 sq. ft./gal @ 1.0 mils 832 - 848 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 3 - 4 hours dust free; 3 - 4 hours dust free;
8 - 10 hours to handle 8 - 10 hours to handle
140°F/60°C 30 minutes 30 minutes
Infra red short wave N/A N/A
Infra red medium wave N/A N/A
Sanding:
Wet by Hand N/A N/A
VOC as applied ≤ 340 gms/liter (≤ 2.8 lbs/gal) ≤ 340 gms/liter (≤ 2.8 lbs/gal)
Comments Shake new tinting bases for 15 minutes using a mechanical paint shaker before placing
on a mixing machine.
Tinting bases on a mixing machine need to be agitated for 15 minutes at the start of
the work day and every 4 hours during the day to ensure good color matching.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
T O P C O AT S
Supreme PLUS
Low VOC Urethane Single Stage
420 gms/liter (3.5 lbs/gal) VOC with LA2799
Description: Limco Supreme PLUS Topcoat 420 gms/liter (3.5 lbs/gal) VOC is a specially formulated 2K Urethane
Single Stage system designed to meet the rigorous demands of Refinish, Commercial Vehicle,
Agricultural and Fleet markets. Limco Supreme PLUS Urethane Single Stage Topcoat 420 gms/liter
(3.5 lbs/gal) VOC dries quickly to a dust-free surface with excellent flow and leveling, good hiding
and mirror-like gloss. The Supreme PLUS Urethane Single Stage Topcoat 420 gms/liter (3.5 lbs/gal)
VOC film is also chemically resistant and has superior hardness.
Substrates prepared
for topcoating: Finish Sanding
Well cured old paint work P500 grit
Primer Surfacer H1000 P320 - P500 grit (dry sand only)
Primer Surfacer LP20 P320 - P500 grit
Primer Surfacer LP610 P320 - P500 grit
Primer Surfacer LP620 P320 - P500 grit
Primer Sealer LP20 Sanding not required
Primer Sealer LP610 Sanding not required
Primer Sealer LP620 Sanding not required
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
To retrieve color information from BASF color retrieval software, use paint line SU35.
For custom Supreme PLUS Low VOC Urethane Single Stage (420 gms/liter) colors, the color
(LA, LIB, G bases) must be mixed 2 parts to 1 part of LA2799 by volume prior to addition of hardener
and reducer.
US Rev. 11/1/16
T E C H N I C A L D A T A
Supreme PLUS
Low VOC Urethane Single Stage
420 gms/liter (3.5 lbs/gal) VOC with LA2799
Flexed
Mixing ratio: 4:1:2 8:3:2:2
Color 4 parts Color 8 parts Color
Hardener 1 part LH601, LH604 or LH606 3 parts LH601, LH604 or LH606
Flex Agent — 2 parts 892
Reducer 2 parts LR21 or LR25 2 parts LR21 or LR25
Coverage 620 - 643 sq. ft./gal @ 1.0 mils 794 - 815 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 3 - 4 hours dust free; 3 - 4 hours dust free;
8 - 10 hours to handle 8 - 10 hours to handle
140°F/60°C 30 minutes 30 minutes
Infra red short wave N/A N/A
Infra red medium wave N/A N/A
Sanding:
Wet by Hand N/A N/A
VOC as applied ≤ 420 gms/liter (≤ 3.5 lbs/gal) ≤ 420 gms/liter (≤ 3.5 lbs/gal)
Comments Shake new tinting bases for 15 minutes using a mechanical paint shaker before placing
on a mixing machine.
Tinting bases on a mixing machine need to be agitated for 15 minutes at the start of
the work day and every 4 hours during the day to ensure good color matching.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
T O P C O AT S
Supreme PLUS
Low VOC Urethane Single Stage
340 gms/liter (2.8 lbs/gal) VOC with LA2899
420 gms/liter (3.5 lbs/gal) VOC with LA2899
Description: Limco Supreme PLUS Low VOC Topcoat is a specially formulated 2K Urethane Single Stage system
designed to meet the rigorous demands of Refinish, Commercial Vehicle, Agricultural and Fleet
markets. Limco Supreme PLUS Low VOC Urethane Single Stage Topcoat dries quickly to a dust-free
surface with excellent flow and leveling, good hiding and mirror-like gloss. The Supreme PLUS Low
VOC Urethane Single Stage Topcoat film is also chemically resistant and has superior hardness.
Substrates prepared
for topcoating: Finish Sanding
Well cured old paint work P500 grit
Primer Surfacer H1000 P320 - P500 grit (dry sand only)
Primer Surfacer LP20 P320 - P500 grit
Primer Surfacer LP610 P320 - P500 grit
Primer Surfacer LP620 P320 - P500 grit
Primer Sealer LP20 Sanding not required
Primer Sealer LP610 Sanding not required
Primer Sealer LP620 Sanding not required
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
To retrieve color information from BASF color retrieval software, use paint line SUSV.
For custom Supreme PLUS Low VOC Urethane Single Stage colors, the color (LA, LIB, G bases) must
be mixed 1 part to 2 parts of LA2899 by volume prior to addition of hardener and reducer.
US Rev. 11/1/16
T E C H N I C A L D A T A
Supreme PLUS
Low VOC Urethane Single Stage
340 gms/liter (2.8 lbs/gal) VOC with LA2899
420 gms/liter (3.5 lbs/gal) VOC with LA2899
340 gms/liter VOC 420 gms/liter VOC
Flexed for either Low VOC
(2.8 lbs/gal) (3.5 lbs/gal)
Mixing ratio: 8:2:2 8:2:1 8:3:2:2
Color 8 parts Color 8 parts Color 8 parts Color
Hardener 2 parts LH601, LH604 or 2 parts LH601, LH604 or 3 parts LH601, LH604 or
LH606 LH606 LH606
Flex Agent — — 2 parts 892
Reducer 2 parts LR21 or LR25 1 part LR10, LR11, LR12, 340 gms/liter VOC:
LR13 or LR15 2 parts LR21 or LR25
or
420 gms/liter VOC:
2 parts LR10, LR11, LR12,
LR13 or LR15
Gravity gun nozzle HVLP 1.3 - 1.5 mm 1.3 - 1.5 mm 1.3 - 1.5 mm
Flash-off time @ 68°F/20°C 5 minutes between coats 5 minutes between coats 5 minutes between coats
Film build 2.0 - 3.0 mils 2.0 - 3.0 mils 2.0 - 3.0 mils
600 - 650 sq. ft./gal 600 - 650 sq. ft./gal 690 - 730 sq. ft./gal
Coverage
@ 1.0 mils @ 1.0 mils @ 1.0 mils
Drying:
68°F/20°C 1 hour 1 hour 1 hour
140°F/60°C 30 minutes 30 minutes 30 minutes
Infra red short wave N/A N/A N/A
Infra red medium wave N/A N/A N/A
Sanding:
Wet by Hand N/A N/A N/A
≤ 340 gms/liter
(≤ 2.8 lbs/gal)
≤ 340 gms/liter ≤ 420 gms/liter
VOC as applied or
(≤ 2.8 lbs/gal) (≤ 3.5 lbs/gal)
≤ 420 gms/liter
(≤ 3.5 lbs/gal)
Comments Shake new tinting bases for 15 minutes using a mechanical paint shaker before placing
on a mixing machine.
Tinting bases on a mixing machine need to be agitated for 15 minutes at the start of
the work day and every 4 hours during the day to ensure good color matching.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
T O P C O AT S
Supreme PLUS
Basecoat
U.S. National Rule VOC
Description: Limco Supreme PLUS U.S. National Rule Basecoat is a Basecoat/Clearcoat system that features high
strength, fast hiding basecoat colors and a very durable clearcoat. This system can be used for the
repair of original basecoat/clearcoat finishes or for a complete paint job.
Substrates prepared
for topcoating: Finish Sanding
Well cured old paint work P500 grit
Primer Surfacer 800K P320 - P500 grit
Primer Surfacer 846 P320 - P500 grit
Primer Surfacer LP20 P320 - P500 grit
Primer Surfacer LP620 P320 - P500 grit
Primer Sealer LP20 Sanding not required
Primer Sealer LP620 Sanding not required
Primer Sealer LS56 Sanding not required
Primer Sealer LS800 Sanding not required
Primer Sealer PS21NR Sanding not required
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
To retrieve color information from BASF color retrieval software, use paint line SPBT.
For custom Supreme PLUS Basecoat (U.S. National Rule) colors, the color (LA, LIB, G bases) must be
mixed 2 parts to 1 part of LA1399 by volume prior to addition of reducer.
US Rev. 11/1/16
T E C H N I C A L D A T A
Supreme PLUS
Basecoat
U.S. National Rule VOC
Mixing ratio: 2:1
Color 2 parts Color
Reducer 1 part LR10, LR11, LR12, LR13 or LR15
Drying:
68°F/20°C 15 - 30 minutes before clearcoating
140°F/60°C 10 minutes
Infra red short wave N/A
Infra red medium wave N/A
Sanding:
Wet by Hand N/A
Comments Shake new tinting bases for 15 minutes using a mechanical paint shaker before placing
on a mixing machine.
Tinting bases on a mixing machine need to be agitated for 15 minutes at the start of
the work day and every 4 hours during the day to ensure good color matching.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
T O P C O AT S
Supreme PLUS
Low VOC Basecoat
420 gms/liter (3.5 lbs/gal) VOC
Description: Limco Supreme PLUS Low VOC Basecoat is a Basecoat/Clearcoat system that features high strength,
fast hiding basecoat colors and a very durable clearcoat. This system can be used for the repair of
original basecoat/clearcoat finishes or for a complete paint job.
Substrates prepared
for topcoating: Finish Sanding
Well cured old paint work P500 grit
Primer Surfacer H1000 P320 - P500 grit (dry sand only)
Primer Surfacer LP20 P320 - P500 grit
Primer Surfacer LP610 P320 - P500 grit
Primer Surfacer LP620 P320 - P500 grit
Primer Sealer LP20 Sanding not required
Primer Sealer LP610 Sanding not required
Primer Sealer LP620 Sanding not required
Clearcoats: LC4200
LC4800
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
To retrieve color information from BASF color retrieval software, use paint line SPBV.
For custom Supreme PLUS Low VOC Basecoat (420 gms/liter) colors, the color (LA, LIB, G bases)
must be mixed 1 part to 2 parts of LA1299 by volume prior to addition of hardener and reducer.
US Rev. 11/1/16
T E C H N I C A L D A T A
Supreme PLUS
Low VOC Basecoat
420 gms/liter (3.5 lbs/gal) VOC
Mixing ratio: 3:1 + 3%
Color 3 parts Color
Reducer 1 - 2 parts LR21 or LR25
Hardener 3% LH601, LH604 or LH606
Drying:
68°F/20°C 15 - 30 minutes before clearcoating
140°F/60°C 10 minutes
Infra red short wave N/A
Infra red medium wave N/A
Sanding:
Wet by Hand N/A
Comments Shake new tinting bases for 15 minutes using a mechanical paint shaker before placing
on a mixing machine.
Tinting bases on a mixing machine need to be agitated for 15 minutes at the start of
the work day and every 4 hours during the day to ensure good color matching.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
T O P C O AT S
Supreme PLUS
2K Direct-to-metal
U.S. National Rule VOC
Description: Limco Supreme PLUS U.S. National Rule 2K Direct-to-metal Topcoat is a two component, high build,
acrylic urethane for topcoating properly prepared bare steel, aluminum and galvanized substrates.
Limco Supreme PLUS 2K Direct-to-metal topcoat is a very glossy, durable and chemically resistant
topcoat finish. It has excellent flow, leveling properties and good sag resistance.
Substrates prepared
for topcoating: Cleaning Finish Sanding Second Cleaning
Steel 203 Wax and Grease Remover P80 - P180 grit 139 Final Wash Cleaner
Aluminum 203 Wax and Grease Remover P120 - P180 grit 139 Final Wash Cleaner
Zinc or Galvanized 203 Wax and Grease Remover Coarse scuff pad 139 Final Wash Cleaner
NOTES: Make sure sanding is not so vigorous that it removes the galvanized or zinc coating.
With the second cleaning, make sure all residue is removed.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
To retrieve color information from BASF color retrieval software, use paint line SDTM.
Surface cleaning and preparation is critical for Limco Supreme PLUS 2K Direct-to-metal Topcoat's
success. All grease, dirt and rust must be removed from substrate.
Agitate thoroughly on a mixing machine before each use.
For custom Supreme PLUS 2K Direct-to-metal (U.S. National Rule) colors, the color (LA, LIB, G bases)
must be mixed 1 part to 2 parts of LA5999 by volume prior to addition of hardener and reducer.
Supreme PLUS
2K Direct-to-metal
U.S. National Rule VOC
Mixing ratio: 4:1:1
Color 4 parts Color
Hardener 1 part LH710
Reducer 1 part LR10, LR11, LR12, LR13 or LR15
Drying:
68°F/20°C 25 - 30 minutes dust free; 2 hours tack free (depending on reducer)
140°F/60°C 30 minutes
Infra red short wave N/A
Infra red medium wave N/A
Sanding:
Wet by Hand N/A
Comments Shake new tinting bases for 15 minutes using a mechanical paint shaker before placing
on a mixing machine.
Tinting bases on a mixing machine need to be agitated for 15 minutes at the start of
the work day and every 4 hours during the day to ensure good color matching.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
T O P C O AT S
Supreme PLUS
2K Direct-to-metal
420 gms/liter (3.5 lbs/gal) VOC
Description: Limco Supreme PLUS 2K Direct-to-metal Topcoat 420 gms/liter (3.5 lbs/gal) VOC is a two component,
high build, acrylic urethane for topcoating properly prepared bare steel, aluminum and galvanized
substrates. Limco Supreme PLUS 2K Direct-to-metal Topcoat 420 gms/liter (3.5 lbs/gal) VOC is a very
glossy, durable and chemically resistant topcoat finish. It has excellent flow, leveling properties
and good sag resistance.
Substrates prepared
for topcoating: Cleaning Finish Sanding Second Cleaning
Steel R-M 909 Final Wipe P80 - P180 grit R-M 909 Final Wipe
Aluminum R-M 909 Final Wipe P120 - P180 grit R-M 909 Final Wipe
Zinc or Galvanized R-M 909 Final Wipe Coarse scuff pad R-M 909 Final Wipe
NOTES: Make sure sanding is not so vigorous that it removes the galvanized or zinc coating.
With the second cleaning, make sure all residue is removed.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
To retrieve color information from BASF color retrieval software, use paint line SDTV.
Surface cleaning and preparation is critical for Limco Supreme PLUS 2K Direct-to-metal Topcoat's
success. All grease, dirt and rust must be removed from substrate.
Agitate thoroughly on a mixing machine before each use.
For custom Supreme PLUS 2K Direct-to-metal (420 gms/liter) colors, the color (LA, LIB, G bases)
must be mixed 1 part to 2 parts of LA5999 by volume prior to addition of hardener and reducer.
Supreme PLUS
2K Direct-to-metal
420 gms/liter (3.5 lbs/gal) VOC
Mixing ratio: 4:1:1
Color 4 parts Color
Hardener 1 part LH710
Reducer 1 part LR21 or LR25
Drying:
68°F/20°C 25 - 30 minutes dust free; 2 hours tack free (depending on reducer)
140°F/60°C 30 minutes
Infra red short wave N/A
Infra red medium wave N/A
Sanding:
Wet by Hand N/A
Comments Shake new tinting bases for 15 minutes using a mechanical paint shaker before placing
on a mixing machine.
Tinting bases on a mixing machine need to be agitated for 15 minutes at the start of
the work day and every 4 hours during the day to ensure good color matching.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
C L E A R C O AT S
Description: Limco LC4000 Clearcoat (High Solids version) is an acrylic urethane clear for use over Limco Supreme
PLUS Basecoat colors. It is designed to increase the profitability and productivity of the repair
facility. It is U.S. National Rule compliant, easy to apply and has excellent gloss and leveling.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
ONLY the "High Solids Version" of LC4000 may be used. Indicated on product labels with a
"starburst".
LC4000 is not covered by a warranty and should not be used with warrantable systems.
US Rev. 11/1/16
T E C H N I C A L D A T A
Coverage 601 sq. ft./gal @ 1.0 mils 729 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 30 minutes dust free; 30 minutes dust free;
8 hours to handle 8 hours to handle
140°F/60°C 30 minutes; must allow 5 minutes 30 minutes; must allow 5 minutes
flash before force dry flash before force dry
Infra red short wave 6 - 8 minutes 6 - 8 minutes
Infra red medium wave N/A N/A
Sanding:
Wet by Hand 1200 or Finer 1200 or Finer
VOC as applied 550 gms/liter (4.6 lbs/gal) 460 gms/liter (4.0 lbs/gal)
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
C L E A R C O AT S
Description: Limco LC4100 High Solids Clearcoat is a U.S. National Rule Compliant acrylic urethane clear for use
over Limco Supreme PLUS Basecoat colors. It is designed to increase the profitability and productivity
of the repair facility. LC4100 is an easy to apply two coat clear that has excellent gloss and leveling.
LC4100 offers a range of reducers to meet your temperature needs.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
LC4100 is not covered by a warranty and should not be used with warrantable systems.
US Rev. 11/1/16
T E C H N I C A L D A T A
Gravity gun nozzle HVLP 1.1 - 1.3 mm 1.1 - 1.3 mm 1.1 - 1.3 mm
Film build 2.0 - 3.0 mils 2.0 - 2.4 mils 2.0 - 3.0 mils
Coverage 617 sq. ft./gal @ 1.0 mils 574 sq. ft./gal @ 1.0 mils 693 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 30 minutes dust free; 30 minutes dust free; 45 minutes dust free;
8 hours to handle 8 hours to handle 8 hours to handle
140°F/60°C 30 minutes; must allow 30 minutes; must allow 30 minutes; must allow
5 minutes flash before 5 minutes flash before 5 minutes flash before
force dry force dry force dry
Infra red short wave 6 - 10 minutes 6 - 10 minutes 6 - 10 minutes
Infra red medium wave N/A N/A N/A
Sanding:
Wet by Hand 1200 or Finer 1200 or Finer 1200 or Finer
VOC as applied 538 gms/liter (4.5 lbs/gal) 501 gms/liter (4.2 lbs/gal) 495 gms/liter (4.1 lbs/gal)
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
C L E A R C O AT S
Description: Limco LC4200 Clearcoat is a low 250 gms/liter (2.1 lbs/gal) VOC acrylic urethane clearcoat for use
over Supreme PLUS Low VOC Basecoat colors. LC4200 is easy to apply and has excellent gloss and
leveling.
Basecoat: Supreme PLUS Low VOC Basecoat 420 gms/liter (3.5 lbs/gal) VOC
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
LC4200 is not covered by a warranty and should not be used with warrantable systems.
US Rev. 8/21/17
T E C H N I C A L D A T A
Coverage 659 sq. ft./gal @ 1.0 mils 693 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 45 minutes dust free; 45 minutes dust free;
8 hours to handle 8 hours to handle
140°F/60°C 30 minutes; must allow 5 minutes 30 minutes; must allow 5 minutes
flash before force dry flash before force dry
Infra red short wave 6 - 10 minutes 6 - 10 minutes
Infra red medium wave N/A N/A
Sanding:
Wet by Hand 1200 or Finer 1200 or Finer
VOC as applied 139 gms/liter (1.2 lbs/gal) 151 gms/liter (1.3 lbs/gal)
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
C L E A R C O AT S
Description: Limco LC4300 Clearcoat is an acrylic urethane clear for use over Limco Supreme PLUS Basecoat
colors. It is designed to increase the profitability and productivity of the repair facility. It is U.S.
National Rule compliant, easy to apply and has excellent gloss and leveling.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
LC4300 is not covered by a warranty and should not be used with warrantable systems.
US Rev. 11/1/16
T E C H N I C A L D A T A
Coverage 548 sq. ft./gal @ 1.0 mils 603 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 30 minutes dust free; 30 minutes dust free;
8 hours to handle 8 hours to handle
140°F/60°C 30 minutes; must allow 5 minutes 30 minutes; must allow 5 minutes
flash before force dry flash before force dry
Infra red short wave 10 - 20 minutes 10 - 20 minutes
Infra red medium wave N/A N/A
Sanding:
Wet by Hand 1500 or Finer 1500 or Finer
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
C L E A R C O AT S
Description: Limco LC4400 Clearcoat is a low 250 gms/liter (2.1 lbs/gal) VOC acrylic urethane clearcoat for use
over Supreme PLUS Low VOC Basecoat colors. LC4400 is easy to apply and has excellent gloss and
leveling.
Basecoat: Supreme PLUS Low VOC Basecoat 420 gms/liter (3.5 lbs/gal) VOC
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
LC4400 is not covered by a warranty and should not be used with warrantable systems.
US Rev. 11/1/16
T E C H N I C A L D A T A
Coverage 492 sq. ft./gal @ 1.0 mils 563 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 30 minutes dust free; 30 minutes dust free;
8 hours to handle 8 hours to handle
140°F/60°C 30 minutes; must allow 5 minutes 30 minutes; must allow 5 minutes
flash before force dry flash before force dry
Infra red short wave 10 - 20 minutes 10 - 20 minutes
Infra red medium wave N/A N/A
Sanding:
Wet by Hand 1200 or Finer 1200 or Finer
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
C L E A R C O AT S
Description: Limco LC4500 Express Clear is a U.S. National Rule Compliant acrylic urethane clear for use over
Limco Supreme PLUS Basecoat colors. It is designed to increase the profitability and productivity of
the repair facility. LC4500 is an easy to apply two coat clear that has excellent gloss and leveling.
LC4500 offers a range of reducers to meet your temperature needs.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
LC4500 is not covered by a warranty and should not be used with warrantable systems
US Rev. 11/1/16
T E C H N I C A L D A T A
Coverage 582 sq. ft./gal @ 1.0 mils 662 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 15 minutes dust free; 15 minutes dust free;
3 - 4 hours to handle 3 - 4 hours to handle
140°F/60°C 30 minutes; may be handled or 30 minutes; may be handled or
polished after cool down polished after cool down
Infra red short wave 6 - 10 minutes 6 - 10 minutes
Infra red medium wave N/A N/A
Sanding:
Wet by Hand 1200 or Finer 1200 or Finer
VOC as applied 532 gms/liter (4.4 lbs/gal) 490 gms/liter (4.1 lbs/gal)
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
C L E A R C O AT S
Description: Limco LC4800 Low 2.0 VOC Express Clear is a two component, 250 gms/liter (2.1 lbs/gal) VOC
compliant fast acrylic urethane clear for use over Supreme PLUS Low VOC Basecoat colors. It is
designed to accommodate fast air-dry and quick bake conditions, increasing the productivity and
profitability for the repair facility. It is ideal for spot and panel repairs with easy application and
good appearance.
Basecoat: Supreme PLUS Low VOC Basecoat 420 gms/liter (3.5 lbs/gal) VOC
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
LC4800 is not covered by a warranty and should not be used with warrantable systems
US Rev. 11/1/16
T E C H N I C A L D A T A
Coverage 632 sq. ft./gal @ 1.0 mils 668 sq. ft./gal @ 1.0 mils
Drying:
68°F/20°C 15 minutes dust free; 20 - 25 minutes dust free
4 hours to handle
140°F/60°C 30 minutes; may be handled or 30 minutes; may be handled or
polished after cool down polished after cool down
Infra red short wave 8 - 10 minutes 8 - 10 minutes
Infra red medium wave N/A N/A
Sanding:
Wet by Hand 1500 or Finer 1500 or Finer
VOC as applied 159 gms/liter (1.4 lbs/gal) 169 gms/liter (1.5 lbs/gal)
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
Click on logo to return to Table of Contents
MISCELLANEOUS
Description: Limco 892 Flex Agent is a urethane additive that gives flexibility to Limco Undercoats, Topcoats and
Clearcoats. Limco 892 is formulated to resist fading, stone chipping and chemical staining while
increasing the durability and flexibility of most interior and exterior parts.
Mixing: When finishing flexible parts, refer to the appropriate technical data sheets for detailed mixing
ratios and processing information.
Undercoat:
• 800K
• 800K tinted wet-on-wet sealer
• LP610 primer surfacer
• LP610 sealer
• LP620 sealer (National Rule and Low VOC)
• LS800
Topcoat:
• Supreme PLUS Urethane Single Stage National Rule (with LA2799 or LA2999)
• Supreme PLUS Low VOC Urethane Single Stage (with LA2799 or LA2899) for both
340 gms/liter (2.8 lbs/gal) VOC and 420 gms/liter (3.5 lbs/gal) VOC
Clearcoat:
• LC4000
• LC4100
• LC4200
• LC4500
• LC4800
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
For information on preparing plastic parts, refer to “Standard Preparation for Plastic Parts” in the
APPLICATION PROCEDURES section of the Limco Technical Manual.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
US Rev. 11/1/16
Click on logo to return to Table of Contents
MISCELLANEOUS
Description: Limco LE800 Fisheye Eliminator is specially developed for use in Limco Supreme PLUS Single Stage
Topcoats and Limco Clearcoats.
Mixing: Add up to 1 ounce (approximately 28 grams) of Limco LE800 Fisheye Eliminator per ready for use
gallon of topcoats and clearcoats.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
Only use if fisheyes or craters are encountered.
DO NOT use in any undercoats or basecoats.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
US Rev. 11/1/16
Click on logo to return to Table of Contents
MISCELLANEOUS
Description: Limco LF01 is a flattening agent that may be added to all Limco Low VOC Supreme PLUS Single
Stage Topcoats and Limco Clearcoats for gloss reduction. Limco LF01 mixes easily and allows
flattening to the extent desired.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
DO NOT use LF01 in any Basecoat color.
Can be mixed with any Low VOC Limco product and still be VOC compliant.
RFU formulas for Limco Clearcoats are available.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
US Rev. 11/1/16
Click on logo to return to Table of Contents
MISCELLANEOUS
Description: Limco LF10 is a flattening agent that may be added to all Limco Supreme PLUS Single Stage
Topcoats and Limco Clearcoats for gloss reduction. Limco LF10 mixes easily and allows flattening
to the extent desired.
Remarks: Always check local VOC laws to ensure that the use of these Limco products is compliant in your
area.
DO NOT use LF10 in any Basecoat color.
Cannot be mixed with any Low VOC Limco product and still be VOC compliant.
RFU formulas for Limco Clearcoats are available.
Materials described are for application by professional trained personnel only using proper equipment. Products may be hazardous & should be used according to label directions & technical data information. Appropriate respiratory protection should be worn at
all times while products are in use—read product label and Material Safety Data Sheet (MSDS) for specific details. Statements & methods described are based upon the latest standard of technology known to the manufacturer. Application procedures cited are
suggestions only & are not to be interpreted as warranty for events resulting from their use. Dilution ratios are intended to provide maximum performance within the typical Volatile Organic Compound (VOC) restriction for product use. Specific VOC limits need to
be referenced to verify local compliance. Altering the solvent or dilution ratio may impact VOC compliance. User is solely responsible to ensure product use and application is in accordance with all applicable regulatory, legislative, and municipal requirements.
US Rev. 11/1/16