You are on page 1of 1

DEMANDS / LOADS

- Railing satifies demands according to NS ISO 14122-3: Safety of machinery. Permanent means
MAX 1500

>10m
of access to machinery. Part 3: Stairs, stepladders and guard-rails
CHS42.4X3.2 - Railings must be established when the distance between two levels is greater than or equal to 0.5m.

SHS40*4
- Railing designed for maximum horizontal load of 80kg/m.

550
B
CHS33.7X3.2

1200
Notes
MAX 1500

650
< 10m
1. Material
FL150*6 Steel grade of profiles S355 unless otherwise specified.
CHS42.4X3.2
2. Step type TLDS (Weland) or equivalent product with same slip resistance.

SHS40*4

500
3. Step width of stairs with oncoming pedestrian traffic should be at least 1000mm.
CHS33.7X3.2 4. Stair stringer typical UPE200 for height between supports up to 3.5m

1100
within specified stair angles.

MI
N.
19
5. For simple straight race staircase between two levels, vertical rise height may be up to 4.0m.

00

600
If the vertical rise height exceeds 4,0m, each stairway should not exceed rise height of H = 3.0m
FL100*6 between each repo.
6. Clearance around handrail should be minimum 100mm with the exception of fixing for post.

2300
MIN.
7. Fasteners
Bolt quality 8.8, nut quality 10 and washers quality 8.
MAX 1500 Bolts, nuts and washers shall be hot dip galvanized, unless otherwise specified.
B 8. Corrosivity and durability class:
Outdoors C5-I according to EN ISO 12944-2.
Inside C2 according to EN ISO 12944-2.
1000

Durability Class H (High) are used on outdoor and indoor structures.


9. Surface
Surfaces to be painted should be blow cleaned to grade Sa 2.5.

>10m
Cleaning grade P2.
C Steps should be galvanized.

MAX H=4000
10. Colors

0.5m - 10m
231 UPE200
FOR MAX HEIGHT Railings - yellow RAL 1018
RUN UP TO H=3.5m Stair stringers and supporting structures - Blue RAL 5010.
NOTE 4 Steps / Gratings - galvanized execution
RISE
194

11. Welding
STAIR STEP General: EN 1090-2
NOTE 2 Welding procedure: EN ISO 15614-1: 2004 as a minimum
Welders: EN 287-1: 2011
Welding: Class C acc. EN ISO 5817
Welding Control: EXC2 acc. NS-EN1090-2
Weld Tolerance: EXC2 acc. EN 1090-2
Unless otherwise specified on the drawing, a = 4mm fillet weld all around to be used.
Remove spatter and slag, welds patched / painted acc. to specified surface.

37 - 42 degrees STAIR GEOMETRY:

Stair angle Rise Run Tread width


a A B C
37 180 240 270
39 190 235 270
40 195 230 240
42 200 225 240

.
MIN
E6 100

A
T
NO

For norwegian version, see H01 2017-03-08 ENGLISH VERSION, FOR USE JSHaa KnEid PISme
STAIR STEP CHS33.7X3.2 drw: 5160074-156-701-01 REV. DATE DESCRIPTION CONSTR. APPROVED
NOTE 2 REVIEWED
This document has been prepared by Norconsult AS as part of the assignment stated below. Intellectual property rights belong to Norconsult AS. The document may only be
used for the purpose stated in the contract between Norconsult AS and the client, and may not be copied or made available by other means or to a greater extent than the
intended purpose requires.
Design engineer Status

FOR USE
Discipline
SHS40*4
Contract no. Design engineer project no

FL100*6
Size Scale Constr. Date
Client
A1 1:10 TSBor 2016-09-16
1:20 Reviewed
MAX 10

A3 = 1/2 SCALE Date

OGSkj 2016-09-16
Projection: Approved Date

MIN 100
Project Erstatning for:

ESCAPE STAIRS MIN. 900 Drawing Title:

ORDINARY STAIRS MIN. 800 / 1000 NOTE 3 4


ELKEM AS THAMSHAVN
4 RAILING AND STAIRS
CLEAR WIDTH OF STAIRS ( C - C ) TYPICAL SECTION OF RAILING ( B - B ) STANDARD EXECUTION
Tekla Structures

ALT. CONNECTION WITH WELDING Norconsult drawing no. Elkem drawing no. Rev.

5160074-156-701-02 H01
ORGINALFORMAT: A1

You might also like