You are on page 1of 32

®

Compression system technical specifications


and product range
®

List of Contents Page

General Information 3
One Fitting for Many Tubes 4
Design 5
Performance 6
Making a Joint 7
High Torque Installations 8
Flanged Fittings 9
Installation Dimensions (capnuts hand tight) 10-12
Product Range 13
Compression Fittings - Brass and DZR 6mm to 108mm 13-17
Accessories for Compression Joints 18-19
Manifolds 20
Matt Chrome Plated Compression Fittings 20-21
ISOCONEX For use with MDPE, PB and PE-X Pipe 22
ISOCONEX Accessories 23
Accessories for use with Imperial Polythene Pipe 23
Copper Tubular Traps 24-25
Bottle Traps 25
Traps - Waste Fittings 26
Accessories 27
Manifolds 27
Stop Valves / Check Valves 28
Draining Taps 28
Fullway Gate Valves to BS5154/B 28
Serviceman Valves to BS6675 28
Plug Taps / Automatic Air Vent / Washing Machine Valve 29
Brass Float Valves 29
Lever Ball Valves 29

page 2
®

General Information

Conex type ‘A’ non-manipulative standard compression The DZR alloy, a joint development of manufacturers and the
fittings are manufactured in accordance with EN 1254-2 and British Non-Ferrous Metal Technology Centre, used in this
4 (formerly BS 864: Part 2), in sizes from 6mm to 108mm. wide range of compression fittings contains a highly effective
corrosion inhibitor. It’s an outstanding material, ideally suited
Applications and Uses to the high quality standards maintained by IBP, and can be
The versatility of the fitting enables it to be used for used where dezincification could cause problems.
connecting tubes in a wide variety of domestic and DZR fittings are marked with the CR symbol, recognised and
commercial applications such as plumbing, heating, fluid accepted by the Water Industry and the British Plumbing
distribution, air pressure lines and air conditioning. Conex Fittings Manufacturers’ Association, and now specified in
compression fittings are especially advantageous in retrofit British Standards as a mark denoting material of assessed
plumbing schemes, where space is confined and/or the use capability of resistance.
of heat must be avoided. The ability to connect different
Within this extensive DZR range, a few fittings are retained in
types of tube is of special importance encouraging users such
gunmetal for technical and commercial reasons.
as original equipment manufacturers to incorporate Conex
compression fittings within their designs. The fitting’s Where dezincification resistant brass is used, it complies
simplicity, versatility and speed of installation makes it a with the requirements of EN12164 CW602N and EN12165
popular choice with installers. CW602N. Table A provides a list of materials and the relevant
European Norme that governs its performance.
Size Availability
6mm–108mm, suitable for connecting copper tubes in Health and Safety
accordance with EN 1057 and many other standards It is the responsibility of the end user to ensure that adequate
including ISO 274. protection is available where required and the necessary
information regarding possible health and safety regulations
Fittings are also suitable for connecting low carbon steel,
is adhered to. Copper and copper alloy fittings are considered
stainless steel and many types of plastic pipe including
non-hazardous under normal circumstances.
crossed linked polyethylene (PE-X) and polybutylene (PB)
All per COSHH 4 REG 1988.
with size compatible outside diameters.
N.B. When using compression fittings with soft copper tube Table A
to EN 1057 - R220 or plastic pipe it is essential that an Material Specification
appropriate tube liner is also fitted.
Brass (Forging) EN12165 CW617N
Imperial copper tube to BS 659 in sizes 3/8", 1/2", 2" and
Brass (Turning) EN12164 CW617N
21/2" sizes can be readily joined using 12mm, 15mm, 54mm
DZR Brass (Forging) EN12165 CW602N
and 66.7mm fittings respectively. Other sizes can be joined
using special adaptors in the range. DZR Brass (Turning) EN12164 CW602N

Reference to our current price list and catalogue will provide DZR Brass (Ring Tube) EN12164 CW602N
more information about the range. Gunmetal (Red Brass) DIN50930-6

Fitting Materials Stress Corrosion


Fittings are generally produced in duplex brass but, to Within certain environments, particularly those containing a
counteract the problem of dezincification and meet certain corrosive medium, stress corrosion of duplex brass fittings
water regulation requirements, they are also available, or may may occur. For further information, please contact our
only be available, in dezincification resistant (DZR) brass or Technical Department.
as dezincification immune gunmetal.
Dezincification of ordinary duplex brass fittings may occur
under certain water supply conditions. The Conex DZR range
of fittings can safely be used in these circumstances.

page 3
®

One Fitting for Many Tubes

Effecting a joint is simple, requiring nothing more than Medium Density Polyethylene – MDPE
suitable spanners whether it be a 6mm or a 108mm fitting. Whether you are joining underground (BS 6572) or above
The symmetrical compression ring seals within the cone ground (BS 6730), our ISO Conex fittings, valves, liners and
angle of the fitting and provides a two-point seal on the tube adaptors provide a comprehensive range enabling a fast and
when the capnut is tightened the correct number of turns secure joint to be made on pipe diameters up to 32mm.
(Table D, page 15). The joint so made will withstand
pressures far in excess of those normally experienced. Other Types of Plastic Pipe
To facilitate installations we also offer a range of accessories IBP offer a variety of fittings for joining tubes such as cross-
that reduce torque loading when making a joint in sizes linked polyethylene (PE-X) and polybutylene (PB), from
35mm to 76.1mm. Whilst most need only a simple simple tube liners to precision made adaptor sets an
compression ring change, the 42mm and 54mm require a dmanifolds, covering 12mm to 32mm tube outside diameters
flanged adaptor set. with wall thicknesses ranging from 1.3mm to 4.4mm. There
Conex compression fittings are especially advantageous in are also adaptor sets that permit the use of standard
retrofit plumbing schemes, in installations where space is compression fittings. Please contact us for more details about
confined, or when the use of heat must be avoided. this range of fittings.

Copper Quality Assurance


Conex compression fittings are capable of joining size- The Company is a B.S.I. Registered Firm of assessed
compatible copper tubes that are manufactured in capability, Registration Number FM 11836, manufacturing in
accordance with EN 1057 (formerly BS 2871: Part 1) and accordance with EN ISO 9001:2000.
many other standards including ISO 274. Conex fittings are manufactured in accordance with EN
1254-2 and 4 (formerly BS 864: Part 2 and 4).
Stainless Steel Most fittings in the range are covered by the B.S.I. Kitemark
Conex compression fittings are capable of joining size- under Licence No. KM 07283 (detailed list available upon
compatible stainless steel tubes such as those manufactured request). Listing can also be found in the WRAS Water
in accordance with BS 4127 and DIN 17455 and 17457. Fittings and Materials Directory under ‘Kitemarked and
When the installer is using tube diameters 35mm to Quality Assured Fittings’.
76.1mm, it is recommended that our low torque fittings are Conex fittings are also approved by many other European test
used. institutions such as KIWA, SITAC, GASTEC, DET NORSKE
VERITAS and DVGW.
In addition to audits carried out by the British Standards
Inspectorate, an internal audit system is also in operation to
further enhance quality control.
H
T
S

(EN1254) Certificate No. FM 11836

page 4
®

Design

Conex fittings are designed to comply with relevant standards Finish Availability
and to minimise flow restriction. Apart from the natural finish, fittings are also offered nickel
The symmetrical compression ring provides a seal within the plated or chrome plated in accordance with EN 248.
cone of the fitting and a two point seal on the tube. Note: When fittings are to be plated by the customer, it is
The simple principle of the Conex compression joint is shown recommended that our Technical Department is contacted for
in the following diagram. The compression ring is compressed guidance.
between two differing tapers within capnut and fitting
respectively. The sharper angle of the body taper constitutes Connecting Threads
a larger area of ring contact in the fitting body, thus reducing Taper male threads are in accordance with ISO 7 and EN
any tendency for the tube to revolve as the joint is being 1254-4. Parallel male threads are in accordance with EN
secured. 1254-4 and ISO 228.
Tightening the capnut to secure the joint causes the Parallel female threads are in accordance with EN 1254-4
compression ring to change form, making a perfect metal x (BS 864: Part 2 Clause 4(c)) and ISO 228.
metal seal that actually indents the tube on both points of Generally, fittings are manufactured with parallel threads but
contact. This ensures a joint that is easily capable of certain products are offered with taper threads. Reference to
withstanding pressures far in excess of those experienced in our product range will provide more details.
normal usage. In tests on 15mm EN1057-R250 (half hard)
the tube bursts without affecting the joint.
Fine threads have been avoided to prevent the danger of cross
threading. Threads on the 8mm, 12mm and 15mm
compression ends are equal to 1/4", 3/8" and 1/2" BSP in
accordance with BS 2779/ISO 228. Other thread sizes are to
BS 84 or ISO 7.
Conex unique ribbed pattern capnuts are supplied on 6mm to
28mm fittings. Sizes 35mm, 42mm and 54mm are supplied
with octagonal capnuts. Fittings in 66.7mm, 76.1mm and
108mm sizes incorporate loose compression plates, where
tightening is through six 3/8" BSW nuts and allthreads.
For high torque applications, devices are available to
facilitate installation.

The Conex Compression Joint

1. Fitting Body 3. Compression ring


2. Capnut 4. Tube

page 5
®

Performance

Hydraulic working temperatures and pressures shown are Internal Reducers


based on EN 1254-2. Table B, prepared from the stated Sizes not quoted within our range may be achieved via the
values, enables direct reading of intermediate values. use of internal reducers either as a three piece or one
Fittings up to and including 28mm can be used at higher piece configuration. They are manufactured from DZR
pressures than those shown provided that the installation (dezincification resistant material CR) or gunmetal, thereby
does not impart additional tensile loads on the joints. Please being resistant or immune to dezincification.
contact our Technical Department for further data. They may N.B. one piece reducers are not designed for use with plastic
also be used with light mineral oils, L.P.G., natural gas or pipes.
compressed air, in accordance with Table C, when assembled The minimum number of turns required is based on the
with copper tubes to EN 1057 (formerly BS 2871: Part 1 reduced diameter. Thus for a 22mm x 15mm reducer, refer
table X, Z, Y). to Table D for the number of turns required for 15mm.
Reducers rely on a metal x metal seal and care should be
Table B
taken to avoid damage prior to assembly. Should difficulty be
COPPER TUBE experienced, the use of a WRAS listed sealant is permitted.

POTABLE WATER
Table C

COPPER TUBE
Temps Max
For Use Tube Not Working
With Sizes Exceeding Pressures
Ø mm ˚C Bar
Potable 30 16
Water 65 10
6 to 54
or 95 7
Light 110 6
Mineral 30 10
Oils 66.7
65 6
to 108
110 4
Water Flow Resistance Through Fittings LPG,
Natural Gas 8 to 28 30 1
Data is readily available in Publication 33 issued by the
Copper Development Association. Compressed 8 to 28 30 7
Air

page 6
®

Making a Joint

6mm–54mm 5. In both cases, tightening of the capnut is effected by hand


1. Ensure that the tube and fitting sizes are compatible. Cut as far as possible, followed by the recommended minimum
the tube end square but ensure tube retains its shape. number of turns (refer to Table D) with a suitable spanner.
The tube will then make even contact with the tube stop Tools with serrated jaws should not be used. A few drops
in the body of the fitting. The use of an appropriate tube of light oil applied to the screw thread before tightening
cutter is recommended where practicable. the nut will reduce the load required to reach the number
of turns. This is particularly applicable to the larger sizes.
2. Remove any burrs from the tube, both inside and out.

N.B. When joining soft copper tube to EN 1057-R220 or


3. Where necessary, insert a suitable tube liner. plastic pipes, it is essential that an appropriate tube liner
4. One of two methods can be employed for making the is also fitted.
joint. The Conex compression joint makes a metal x metal seal
a) The tube can be firmly inserted into the Conex which normally eliminates the need for jointing
compression fitting without removing the capnut and compounds and sealants. On larger sizes, particularly
compression ring. 54mm, it may be necessary to use an additional WRAS
Care should be taken to ensure that the compression ring approved sealant. Jointing instructions, when using
is in the correct position and that the tube makes firm sealant, are available from our Technical Department.
contact with the tube stop in the body of the fitting.
b) The capnut and compression ring can be removed, located
onto the tube in logical sequence, and the tube fully
inserted into the Conex compression fitting.

page 7
®

High Torque Installations

IBP has designed devices to reduce tightening torque for Assembly of Coned Joints and Screwed Fittings
35mm to 76.1mm applications. They are particularly useful Coned Joints
where space is restricted and/or stainless steel tube is being Cone face connectors to EN 1254-4 (BS 864: Part 2) rely on
joined. When using stainless steel tube, water quality a metal x metal seal and care should be taken to avoid
approved PTFE coated compression rings must be used on damage prior to assembly. Should difficulty be experienced,
sizes 35mm and above. Whilst most sizes are a simple the use of a WRAS listed sealant is permitted. Do not
compression ring change, we recommend that 42mm and overtighten.
54mm sizes use a flanged adaptor set comprising one flange,
one compression plate, four allthreads, four nuts and one Threaded Joints for Liquid Applications
PTFE coated compression ring. Assembly is commenced by The use of a WRAS listed sealant or tape (e.g. PTFE) is
discarding the standard capnut and compression ring and recommended for making joints on fittings with taper male
securing the threaded flange to the exposed end of the fitting threads. For making joints with parallel connector threads, a
and is completed by following the instructions for flanged good quality washer made from a WRAS listed material
fittings 66.7mm –108mm. should be used. Suitable washers are supplied with Conex tap
Note: The installation procedures within this brochure are connector fittings and these should be used.
generally for water applications. Installation procedures may
vary for non-water applications and other tube material Threaded Joints for Gas Applications
specifications. In these cases you are advised to contact our An approved gas sealant must be used for making joints on
Technical Department for clarification. fittings with taper male threads and female parallel threads.

Table D

TUBE 6mm 28mm


MATERIAL SPECIFICATION SIZE ä to 22mm to
18mm 54mm
AND HARD COPPER

EN1057-R250 No of turns 11⁄4 1 ⁄4


3
HALF HARD

(Half Hard) Liner none none none

EN1057-R290 No of turns 1 3
⁄4 ⁄2
1

(Hard)
Liner none none none

SIZE ä 8mm 10mm 15mm 18mm 22mm


COPPER
SOFT

EN1057-R220 No of turns 11⁄4 11⁄4 11⁄4 11⁄4 1


Liner: SC1 8 x 1.0 10 x 1.0 15 x 1.0 18 x 1.0 22 x 1.0

6mm 35mm 67mm


SIZE ä
STAINLESS

to 28mm to to
STEEL

22mm 54mm 76.1mm


BS4127
No of turns 3
⁄4 1
⁄2 1
⁄ 2* *
Liner none none none none

SIZE ä 10mm 15mm 22mm 28mm

POLYBUTYLENE (PB) No of turns 11⁄2 11⁄2 11⁄2 11⁄2


Liner: PP 10 x 1.5/1.8 15 x 1.7/2.0 22 x 2.0/2.3 28 x 2.6/2.9

SIZE ä 10mm 15mm 22mm 28mm


FLEXIBLE

CROSS LINKED
No of turns 1 ⁄2
1
1 ⁄2
1
1 ⁄21
11⁄2
POLYETHYLENE (PE-X)
Liner: PP 10 x 1.5/1.8 15 x 1.5/1.8 22 x 2.0/2.3 28 x 2.6/2.9

SIZE ä 20mm 25mm 32mm


MEDIUM DENSITY
No of turns 11⁄2 11⁄2 11⁄2
POLYETHYLENE (MDPE)
Liner: PY 20 x 2.3/2.6 25 x 2.3/2.6 32 x 3.0/3.4

PLEASE CONSULT OUR TECHNICAL DEPARTMENT WHEN USING OTHER MATERIALS.


* When using tube diameters 35mm to 76.1mm, it is recommended that our low torque fittings are used. Please refer to our Technical Department.

page 8
®

Flanged Fittings

66.7mm - 108mm b) The compression plate and compression ring can be


1. Ensure that the tube and fitting sizes are compatible. Cut removed by first unscrewing the 3/8" BSW nuts. Then by
the tube end square but ensure tube retains its shape. The locating the compression plate and compression ring onto
tube will then make even contact with the tube stop in the the tube in logical sequence, the tube is inserted into the
body of the fitting. fitting, or fitting onto the tube, until positive contact is
2. Remove any burrs from the tube, both inside and out. reached. The compression ring and compression plate are
3. One of two methods can be employed for making the joint. then correctly situated in their original position, the nuts
are replaced and tightened until hand tight and the same
a) The tube can be firmly inserted into the Conex
amount of allthread shows through each nut.
compression fitting without removing the compression
plate and compression ring. 4. In both cases the nuts are then further tightened a
Care should be taken to ensure that the compression ring minimum of 2 full turns in increments of 1/2 a turn only,
is in the correct position and that the tube makes firm on each position in the sequence shown in the diagram. To
contact with the tube stop in the body of the fitting. avoid overtightening the maximum number of turns is 21/2.
The 3/8" BSW nuts are then tightened until hand tight and
the same amount of allthread shows through each nut.

6 1 2 3 4 5 6

1. Fitting 4. Compression Plate


2. Allthread 5. Nut
3. Compression Ring 6. Tube

Note: The compression plate before and after correct


assembly should be parallel to the face of the fitting body.

page 9
®

Installation Dimensions (capnuts hand tight)

COMPRESSION END 302 or S302 STRAIGHT COUPLER


TUBE STOP DIMENSION Conex x Male Thread (Parallel)
Standard for all Components

A A B C
Size (mm) Size (mm) (BSP) (mm)
15 21.8 15 x 1/2 15 1/2 37.5
22 25.4 22 x 3/4 22 3/4 42.5
28 26.0 22 x 1 22 1 41.5
35 30.0 28 x 1 28 1 45.0

63 CAPNUT 303 or S303 STRAIGHT COUPLER


Conex x Female Thread (Parallel)

A (mm) B A B C
Size Maximum Minimum (mm) Size (mm) (BSP) (mm)
15 24.55 24.33 27.3 15 x 1/2 15 1/2 39.5
22 32.74 32.53 36.5 22 x 3/4 22 3/4 43.5
28 39.16 38.94 45.2 22 x 1 22 1 49.0
35 46.85 46.35 50.0 28 x 1 28 1 48.0

301 or S301 STRAIGHT COUPLER 303SF or S303SF


Conex x Conex STRAIGHT COUPLER
Conex x Swivel Female Thread

A B C A B C
Size (mm) (mm) (mm) Size (mm) (BSP) (mm)
15 x 15 15 15 44.3 15 x 1/2 15 1/2 44.0
22 x 15 22 15 50.5 15 x 3/4 15 3/4 44.5
22 x 22 22 22 52.0 22 x 3/4 22 3/4 48.0
28 x 28 28 28 53.5 28 x 1 28 1 49.0

N.B. Conex capnuts greater than 28mm will have octagonal external form.
For other dimensional data, please contact our Technical Department.

page 10
®

321 or S321 TANK CONNECTOR 402 or S402 ELBOW


Conex Conex x Male Thread (Parallel)

A B C A B C D
Size (mm) (mm) (mm) Size (mm) (BSP) (mm) (mm)
15 15 35.0 49.0 15 x 1/2 15 1/2 25.7 34.0
22 22 43.0 46.0 22 x 3/4 22 3/4 32.0 37.5
28 28 49.0 48.0 22 x 1 22 1 34.5 42.7
35 35 56.5 45.5 28 x 1 28 1 38.5 43.2

323 or S323 STOP END 403 or S403 ELBOW


Conex Conex x Female Thread (Parallel)

A B A B C D
Size (mm) (mm) Size (mm) (BSP) (mm) (mm)
15 15 26.0 15 x 1/2 15 1/2 15.3 34.3
22 22 27.0 22 x 3/4 22 3/4 28.5 39.4
28 28 31.0 22 x 1 22 1 30.5 42.6
35 35 34.7 28 x 1 28 1 35.1 43.9

401 or S401 ELBOW 403SF or S403SF ELBOW


Conex x Conex Conex x Swivel Female Thread

A B C D A B C D
Size (mm) (mm) (mm) (mm) Size (mm) (BSP) (mm) (mm)
15 x 15 15 15 31.5 31.5 15 x 1/2 15 1/2 27.4 31.4
22 x 22 22 22 36.9 36.9 15 x 3/4 15 3/4 33.5 29.5
28 x 28 28 28 41.9 41.9 22 x 3/4 22 3/4 32.0 36.5
35 x 35 35 35 48.2 48.2 28 x 1 28 1 44.0 41.0

N.B. Conex capnuts greater than 28mm will have octagonal external form.
For other dimensional data, please contact our Technical Department.

page 11
®

403WL or S403WL WALL 615 or S615 TEE


PLATE ELBOW Conex x Conex x Male Thread (Parallel)
Conex x Female Thread (Parallel)

A B C D A B C D E
Size (mm) (BSP) (mm) (mm) Size (mm) (mm) (BSP) (mm) (mm)
15 x 1/2 15 1/2 41.8 33.8 15 x 15 x 1/2 15 15 1/2 25.7 68.0
22 x 1/2 22 1/2 47.0 36.9 15 x 15 x 3/4 15 15 3/4 34.0 75.5
22 x 3/4 22 3/4 54.0 38.0 22 x 22 x 3/4 22 22 3/4 32.6 77.0
28 x 1 28 1 65.0 44.0 28 x 28 x 1 28 28 1 39.7 89.6

601EQ or S601EQ TEE-EQUAL 617 or S617 TEE


Conex All Ends Conex x Conex x Female Thread (Parallel)

A B C D E A B C D E
Size (mm) (mm) (mm) (mm) (mm) Size (mm) (mm) (BSP) (mm) (mm)
15 x 15 x 15 15 15 15 31.5 63.0 15 x 15 x 1/2 15 15 1/2 25.4 66.2
22 x 22 x 22 22 22 22 36.9 73.8 15 x 15 x 3/4 15 15 3/4 26.2 74.1
28 x 28 x 28 28 28 28 41.9 83.8 22 x 22 x 3/4 22 22 3/4 28.5 78.2
35 x 35 x 35 35 35 35 48.2 96.4 28 x 28 x 1 28 28 1 35.0 85.8

601 or S601 TEE-UNEQUAL 684 or S684 TEE


Conex All Ends Conex x Female Thread (Parallel) x Conex

A B C D E A B C D E
Size (mm) (mm) (mm) (mm) (mm) Size (mm) (BSP) (mm) (mm) (mm)
22 x 15 x 15 22 15 15 34.3 65.9 15 x 1/2 x 15 15 1/2 15 33.0 55.0
22 x 15 x 22 22 15 22 36.9 70.2 22 x 1/2 x 22 22 1/2 22 37.0 63.0
22 x 22 x 15 22 22 15 34.3 69.7 22 x 3/4 x 22 22 3/4 22 39.5 65.7
28 x 28 x 15 28 28 15 37.9 68.2 28 x 1 x 28 28 1 28 45.0 79.0

N.B. Conex capnuts greater than 28mm will have octagonal external form.
For other dimensional data, please contact our Technical Department.

page 12
®

Product Range
COMPRESSION FITTINGS - Brass and DZR 6mm to 108mm
Part No. Description Size Size Part No. Description Size Size
Brass DZR Brass DZR
301 Straight Coupler - 6 301V Straight Coupler 15 -
S301 Conex x Conex - 8 with Air Vent
- 10 Conex x Conex
12 12
15 15
18 18
22 22
28 28
35 35
- 42 302 Male Straight Connector - 6 x 1/8
- 54 S302 Conex x Male Thread - 8 x 1/4
(Parallel ISO 228) - 8 x 3/8
Straight Coupler - 67
- 8 x 1/2
Conex x Conex - 76
- 10 x 1/4
- 108
- 10 x 3/8
- 10 x 1/2
12 x 1/4 -
12 x 3/8 12 x 3/8

12 x 1/2 12 x 1/2
301 Reduced Straight Coupler - 8x6
15 x 1/4 -
S301 Conex x Conex - 10 x 8
15 x 3/8 15 x 3/8
- 12 x 8
15 x 1/2 15 x 1/2
- 12 x 10
15 x 3/4 15 x 3/4
- 15 x 8
18 x 1/2 18 x 1/2
- 15 x 10
18 x 3/4 18 x 3/4
15 x 12 15 x 12
22 x 1/2 22 x 1/2
- 16 x 15
22 x 3/4 22 x 3/4
18 x 12 -
22 x 1 22 x 1
- 18 x 15
- 28 x 3/4
22 x 15 22 x 15
28 x 1 28 x 1
22 x 18 -
- 28 x 15 28 x 11/4 -
28 x 22 28 x 22 - 35 x 1
- 35 x 22 35 x 11/4 35 x 11/4
- 35 x 28 42 x 11/2 42 x 11/2
54 x 2 54 x 2

301BH Straight Coupler Bulkhead 15 -


Conex x Conex 22 - - 67 x 21/2
- 76 x 3
- 108 x 4

301BP Straight Coupler Burst 12 x 100 -


Pipe Repair 15 x 100 - 302B Extended Male Straight 15 x 1/2 x 22 -
Conex x Conex 18 x 100 - S302B Connector with Back Nut 22 x 3/4 x 22 -
22 x 100 - Conex x Male Thread x 28 x 1 x 22 -
Tail Length (mm) 35 x 11/4 x 22 -
42 x 11/2 x 22 -
S301C0 Crossover - 15 54 x 2 x 25 -
Conex x Conex - 18
- 22

- 67 x 21/2 x 80
301DA Straight Coupler with Drain Tap 15 - - 76 x 3 x 80
Conex x Conex 22 -

302CB Extended Male Straight 15 x 1/2 x 38 -


S301M Imperial to Metric - 3 x 76 Connector with Back 22 x 3/4 x 38 -
Straight Coupler Nut (Long)
Conex x Conex Conex x Male Thread x 28 x 1 x 44 -
Tail Length (mm)

page 13
®

COMPRESSION FITTINGS - Brass and DZR 6mm to 108mm

Part No. Description Size Size Part No. Description Size Size
Brass DZR Brass DZR
302TA Male Straight Connector - 10 x 3/8 321 Tank Connector 15 15
S302TA Conex x Male Taper Thread - 10 x 1/2 S321 Conex 22 22
to ISO 7 12 x 3/8 - 28 28
12 x 1/2 - 35 -
15 x 3/8 - - 42
15 x 1/2 - - 54
15 x 3/4 -
18 x 1/2 -
18 x 3/4 - 323 Stop End - 8
22 x 1/2 - S323 Conex - 10
22 x 3/4 - 12 12
22 x 1 - 15 15
28 x 3/4 - - 18
28 x 1 - 22 22
28 28
- 35
303 Female Straight Connector - 8 x 1/4 - 42
S303 Conex x Female Thread - 8 x 3/8 - 54
(Parallel ISO 228) - 8 x 1/2
- 10 x 1/4 401 Elbow - 6
- 10 x 3/8 S401 Conex x Conex - 8
- 10 x 1/2 - 10
12 x 3/8 12 x 3/8 12 12
12 x 1/2 12 x 1/2 15 15
15 x 3/8 15 x 3/8 18 18
22 22
15 x 1/2 15 x 1/2
28 28
15 x 3/4 15 x 3/4
35 35
15 x 1 - 42 42
18 x 1/2 18 x 1/2 54 54
18 x 3/4 18 x 3/4
22 x 1/2 -
22 x 3/4 22 x 3/4 - 67
22 x 1 22 x 1 - 76
- 28 x 3/4 - 108
28 x 1 28 x 1
28 x 11/4 -
- 35 x 1 401 Reduced Elbow - 12 x 10
- 35 x 11/4 S401 Conex x Conex - 15 x 10
- 42 x 11/2 15 x 12 -
- 54 x 2 18 x 15 -
22 x 15 22 x 15
- 28 x 15
- 67 x 21/2 - 28 x 22
- 76 x 3 - 54 x 28

401DA Elbow with Drain Tap 15 -


Conex x Conex 22 -
303SC Cylinder Straight Connector 22 x 1 -
28 -
Conex x Swivel Female Thread

1/2 1/2 401/0 Obtuse Elbow 15 -


303SF Straight Tap Connector 15 x 15 x
3/4 Conex x Conex 22 -
S303F Conex x Swivel Female Thread - 15 x
3/4 3/4 28 -
22 x 22 x

1/2 S401S Slow Bend - 15


303ST Female Straight Connector 15 x -
3/4 Conex x Conex - 22
for Pillar Taps 15 x -
3/4 - 28
Conex x Female Thread 22 x -
(Parallel ISO 228)

page 14
®

COMPRESSION FITTINGS - Brass and DZR 6mm to 108mm

Part No. Description Size Size Part No. Description Size Size
Brass DZR Brass DZR
401V Elbow with Air Vent 15 - 402TA Male Elbow - 10 x 1/2

Conex x Conex 22 - S402TA Conex x Male Taper Thread 12 x 3/8 -


to ISO 7 12 x 1/2 -
15 x 3/8 -
15 x 1/2 -
15 x 3/4 -
18 x 1/2 -
18 x 3/4 -
402 Male Elbow - 8 x 1/4 22 x 3/4 -
S402 Conex x Male Thread - 8 x 3/8 22 x 1 -
(Parallel ISO 228) - 10 x 3/8 28 x 1 -
- 10 x 1/2 35 x 11/4 -
- 12 x 3/8 42 x 11/2 -
- 12 x 1/2
- 15 x 3/8
15 x 1/2 15 x 1/2 S402W Male Wall Plate Elbow - 15 x 3/4
15 x 3/4 15 x 3/4 Conex x Male Thread
18 x 1/2 18 x 1/2 (Parallel ISO 228)
- 18 x 3/4
- 22 x 1/2
22 x 3/4 22 x 3/4
22 x 1 22 x 1
28 x 3/4 -
28 x 1 28 x 1 403 Female Elbow - 8 x 1/4
- 35 x 11/4 S403 Conex x Female Thread - 10 x 3/8
- 42 x 11/2 (Parallel ISO 228) - 10 x 1/2
54 x 2 54 x 2 - 12 x 3/8
12 x 1/2 12 x 1/2
- 15 x 3/8
15 x 1/2 15 x 1/2
- 67 x 21/2 15 x 3/4 15 x 3/4
18 x 1/2 -
18 x 3/4 18 x 3/4
22 x 1/2 22 x 1/2
402B Extended Male Elbow with 15 x 1/2 x 22 - 22 x 3/4 22 x 3/4
Back Nut 22 x 3/4 x 22 - 22 x 1 -
Conex x Male Thread (Parallel 28 x 3/4 -
ISO 228) x Tail Length (mm) 28 x 1 28 x 1
- 35 x 11/4
42 x 11/2 42 x 11/2
- 54 x 2

402DA Male Elbow with Drain Tap 15 x 1/2 - S403SC Cylinder Elbow - 22 x 1
Conex x Male Thread 22 x 3/4 - Conex x Swivel Female Thread
(Parallel ISO 228)

402CB Extended Male Elbow with 15 x 1/2 x 38 - 403SF Bent Tap Connector 15 x 1/2 15 x 1/2
Back Nut 22 x 3/4 x 38 - S403SF Conex x Swivel Female Thread 15 x 3/4 -
Conex x Male Thread 22 x 1/2 -
(Parallel ISO 228) x 22 x 3/4 -
Tail Length (mm)

S402S Slow Male Bend - 22 x 3/4

Conex x Male Thread 403W Female Wall Plate Elbow 12 x 1/2 12 x 1/2
(Parallel ISO 228) S403W (2 Hole) 15 x 1/2 15 x 1/2
Conex x Female Thread
(Parallel ISO 228)

page 15
®

COMPRESSION FITTINGS - Brass and DZR 6mm to 108mm

Part No. Description Size Size Part No. Description Size Size
Brass DZR Brass DZR
403WE Extended Female 15 x 1/2 - 601 Tee - Reduced End - 15 x 12 x 15
Wall Plate 15 x 1/2 - S601 Conex all Ends - 18 x 15 x 18
Elbow (3 Hole) Polished/ 22 x 15 x 22 22 x 15 x 22
Conex x Female Thread Chrome 22 x 18 x 22 -
(Parallel ISO 228) plated 28 x 15 x 28 -
- 28 x 22 x 28

403WL Female Wall Plate Elbow - 10 x 1/2


S403WL (3 Hole) - 12 x 1/2
Conex x Female Thread 15 x 1/2 15 x 1/2 601 Tee - Reduced End - 15 x 12 x 12
(Parallel ISO 228) 18 x 1/2 - S601 and Branch 18 x 12 x 12 -
22 x 1/2 - Conex all Ends - 18 x 15 x 15
- 22 x 3/4 22 x 15 x 15 22 x 15 x 15
28 x 15 x 15 -
- 28 x 22 x 15
- 28 x 22 x 22

601EQ Tee - Equal - 6


S601EQ Conex all Ends - 8
- 10
12 12 601 Tee - Reduced Both Ends - 12 x 12 x 15
15 15 S601 Conex all Ends - 15 x 15 x 18
18 18 15 x 15 x 22 15 x 15 x 22
22 22 - 22 x 22 x 28
28 28
- 35
- 42
- 54

- 67 S601C Corner Tee - 15


- 76 Conex all Ends - 22

601 Tee - Reduced Branch - 12 x 12 x 10


S601 Conex all Ends - 15 x 15 x 10
- 15 x 15 x 12
- 18 x 18 x 12
- 18 x 18 x 15 1/2
S615 Tee with Male Branch - 15 x 15 x
- 22 x 22 x 12 1/2
Conex x Conex x - 22 x 22 x
22 x 22 x 15 22 x 22 x 15 3/4
Male Thread - 22 x 22 x
- 22 x 22 x 18
(Parallel ISO 228)
28 x 28 x 15 28 x 28 x 15
28 x 28 x 22 28 x 28 x 22
- 35 x 35 x 15
- 35 x 35 x 22
- 35 x 35 x 28
- 42 x 42 x 15
- 42 x 42 x 22 617 Tee with Female Branch - 12 x 12 x 3/8
- 42 x 42 x 28 S617 Conex x Conex x - 12 x 12 x 1/2
- 42 x 42 x 35 Female Thread 15 x 15 x 1/4 -
54 x 54 x 15 - (Parallel ISO 228) 15 x 15 x 1/2 15 x 15 x 1/2
54 x 54 x 22 - 15 x 15 x 3/4 -
54 x 54 x 28 54 x 54 x 28 18 x 18 x 1/2 -
- 54 x 54 x 35 18 x 18 x 3/4 -
- 54 x 54 x 42 22 x 22 x 1/2 22 x 22 x 1/2
- 22 x 22 x 3/4
22 x 22 x 1 -
- 67 x 67 x 28 - 28 x 28 x 1/2
- 67 x 67 x 35 28 x 28 x 3/4 -
- 67 x 67 x 42 - 28 x 28 x 1
- 67 x 67 x 54
- 76 x 76 x 28
- 76 x 76 x 54

page 16
®

COMPRESSION FITTINGS - Brass and DZR 6mm to 108mm

Part No. Description Size Size Part No. Description Size Size
Brass DZR Brass DZR
S617W Wall Plate Tee with - 15 x 15 x 1/2 63 Capnut 6 -
Female Thread Branch - 22 x 22 x 1/2 8 -
Conex x Conex x 10 -
Female Thread 12 -
(Parallel ISO 228) 15 -
18 -
22 -
28 -
35 -
631 Tee with Male End - 15 x 1/2 x 15 42 -
S631 Conex x Male Thread - 22 x 3/4 x 22 54 -
3/4 -
(Parallel ISO 228) 22 x 1 x 22 -
x Conex 11/4 -

67 -
76 -
108 -

1/2 1/2 63B Blank Cap 6 -


645 Tee with Threaded x x 15 -
(Supplied with a 8 -
Ends
rubber washer) 10 -
Female Threaded
12 -
(Parallel ISO 228)
15 -
x Male Thread
18 -
(Parallel ISO 228) 22 -
x Conex 28 -
35 -
42 -
54 -

684 Tee with Female End - 15 x 1/2 x 15


1/2
63TV Terminal Air Vent 15 -
S684 Conex x Female - 18 x x 18 Capillary Ended
Thread 22 x 1/2 x 22 -
(Parallel ISO 228) 22 x 3/4 x 22 -
x Conex 28 x 1 x 28 -

63V Air Vent for 15 -


Compression End
901 Cross - Equal 15 -
Conex all Ends 22 -

Cross - Reduced 22 x 15 x 15 x 15 -
Conex all Ends

S61 Blanking Piece - 12


- 15
- 22

page 17
®

ACCESSORIES FOR COMPRESSION JOINTS

Part No. Description Size Size Part No. Description Size Size
Brass DZR Brass DZR
64LT Low Torque Flanged - 42 S68 Internal Reducer - 10 x 8
Adaptor - 54 Three Piece - 12 x 8
- 12 x 10
- 15 x 8
- 15 x 10
- 15 x 12
- 18 x 12
- 18 x 15
65LT Low Torque Compression - 35 - 22 x 12
PTFE Coated Ring - 42 - 22 x 15
- 54 - 22 x 18
- 28 x 12
- 28 x 15
- 28 x 18
- 28 x 22
- 35 x 15
- 35 x 18
65 Compression Ring - 6 - 35 x 22
- 8 - 35 x 28
- 10 - 42 x 15
- 12 - 42 x 22
- 15 - 42 x 28
- 42 x 35
- 18
- 54 x 15
- 22 - 54 x 22
- 28 - 54 x 28
- 35 - 54 x 35
- 42 - 54 x 42
- 54 - 67 x 54
- 67 - 76 x 67
- 76
- 108
3/4 S68E External Reducer - 76 x 42
-
- 76 x 54
- 1
- 11/4
- 3

8531 Running Nipple 1/4 -


Male Thread 3/8 -
1/2 S68S Adaptor - 3 x 76
(Parallel ISO 228) -
3/4 Imperial/Metric
Replaces Part No. 66 -

8241 Reduced Bush 3/8 x 1/4 -


Male Thread 1/2 x 1/4 -
1/2 x 3/8 S68S Adaptor - 42 x 11/2
(Parallel ISO 228) x -
3/4 x 1/4 Metric/Imperial - 108 x 4
Female Thread -
(Parallel ISO 228) 3/4 x 3/8 -
Replaces Part No. 67 3/4 x 1/2 -
1 x 3/8 -
1 x 1/2 -
1 x 3/4 -
S68SP Internal Reducer - 10 x 8
11/4 x 1/2 -
- 12 x 8
11/4 x 3/4 - - 12 x 10
11/4 x 1 - - 15 x 8
11/2 x 11/2 - - 15 x 10
11/2 x 13/4 - - 15 x 12
11/2 x 1 - - 18 x 10
11/2 x 11/4 - - 18 x 12
2x 1 - - 18 x 15
2 x 11/4 - - 22 x 12
2 x 11/2 - - 22 x 15
- 22 x 18
- 28 x 12
S68 Internal Reducer - 8x6 - 28 x 15
Single Piece - 28 x 18
- 28 x 22
- 35 x 15
- 35 x 18
- 35 x 22
- 35 x 28

page 18
®

ACCESSORIES FOR COMPRESSION JOINTS

Part No. Description Size Size Part No. Description Size Size
Brass DZR Brass DZR
72 Adaptor 1/2 - 85 Capnut Spanner Zinc Plated 22 x 15 -
Male Thread 3/4 - Conex
(Parallel ISO 228) x
Female Thread
(Parallel ISO 228)

85R ‘C’ Capnut Spanner Zinc Plated 22 x 15 -


Conex
8270 Straight Coupler 1/4 -
Female Thread 3/8 -
(Parallel) x 1/2 -
Female Thread 3/4 -
(Parallel ISO 228) 1 -
Replaces Part No. 73 11/4 - 96 Brass Washer Thread Size
11/2 - (for Male Threaded Ends) 1/2 -
2 - 3/4 -
1 -

C73 Adaptor 1/2 x 15 -


Female Thread 3/4 x 22 -
(Parallel) x
Conex Female Thread 97 Sealing Washer 1/2 -
(Parallel ISO 228) (for Swivel Fittings 3/4 -
303SF & 403SF)

74 Adaptor for Tap Extension 1/2 -


Male Thread (Parallel) x 3/4 -
Female Thread
(Parallel ISO 228) 98 Rubber Washer 15 -
(for Blank Capnuts) 18 -
22 -
28 -
35 -
1/2
42 -
8310F Backnut - 54 -
Female Thread 3/4 -
(Parallel ISO 228)
Replaces Part No. 77 1 -
11/4 -
11/2 -
2 -

S77 Backnut - 21/2


Female Thread - 3
(Parallel ISO 228)

C77 Backnut 15 -
Conex Female Thread 22 -
28 -
35 -
42 -
54 -

8595 Flanged Plug 1/8 -


Male Thread 1/4 -
(Parallel Thread ISO 228) 3/8 -
Replaces Part No. 78 1/2 -
3/4 -
1 -
11/4 -
11/2 -
2 -

page 19
®

MANIFOLDS MATT CHROME PLATED COMPRESSION FITTINGS

Part No. Description Size Size Part No. Description Size Size
Brass DZR Brass DZR
45584 Manifold for 22mm 8 - 301CP Straight Coupler - 10
Tube with Capillary S301CP Conex x Conex Matt Chrome - 12 x 10
Main Connecting 10 - Plated - 12
Compression Outlets 15 15
4 Port 22 22
Male Copper x - 28
Copper x - 35
Compression Outlet

302CP Male Straight Connector 15 x 1/2 15 x 1/2


Conex x Male Thread 22 x 3/4 22 x 3/4
(Parallel ISO 228) - 28 x 1
Matt Chrome Plated - 35 x 11/4
45586 Manifold for 22mm 10 -
Tube with Capillary
Main Connecting
Compression Outlets
6 Port
Male Copper x 302TACP Male Straight Connector 15 x 1/2 -
Copper x Conex x Male Taper Thread to 22 x 3/4 -
Compression Outlet ISO 7 Matt Chrome Plated 28 x 1 -

303CP Female Straight Connector 15 x 1/2 15 x 1/2


S303CP Conex x Female Thread 22 x 3/4 22 x 3/4
(Parallel ISO 228) - 22 x 1
45604 Manifold for 22mm 8 - Matt Chrome Plated - 28 x 1
Capillary Tube - 35 x 11/4
Connection with 10 -
Capillary Outlets
4 Port
Copper x Copper
S303SFCP Straight Tap Connector - 15 x 1/2
Outlet
Conex x Swivel Female Thread - 22 x 3/4

Matt Chrome Plated

S323CP Stop End - 15


Conex - 22
Matt Chrome Plated - 28

401CP Elbow - 10
S401CP Conex x Conex - 12
Matt Chrome Plated 15 15
22 22
28 28
- 35

402CP Male Elbow 15 x 1/2 -


S402CP Conex x Male Thread (Parallel - 22 x 3/4
ISO 228) Matt Chrome Plated - 28 x 1
- 35 x 11/4

page 20
®

MATT CHROME PLATED COMPRESSION FITTINGS

Part No. Description Size Size Part No. Description Size Size
Brass DZR Brass DZR
402TACP Male Elbow 15 x 1/2 - 617CP Tee with Female Branch 15 x 15 x 1/2 15 x 15 x 1/2

Conex x Male Taper 22 x 3/4 - S617CP Conex x Conex x Female - 22 x 22 x 3/4

Thread to ISO 7 Thread (Parallel ISO 228)


Matt Chrome Plated Matt Chrome Plated

403CP Female Elbow 15 x 1/2 15 x 1/2


S403CP Conex x Female Thread - 22 x 3/4
(Parallel ISO 228) - 28 x 1 684CP Tee with Female End - 15 x 1/2 x 15
Matt Chrome Plated - 35 x 11/4 S684CP Conex x Female Thread
(Parallel ISO 228)
x Conex
Matt Chrome Plated

403SFCP Bent Tap Connector - 15 x 1/2


S403SFCP Conex x Swivel Female 22 x 3/4 -
Thread 63CP Capnut 10 -
Matt Chrome Plated Matt Chrome Plated 15 -
22 -
28 -
35 -

403WCP Female Wall Plate Elbow 15 x 1/2 15 x 1/2 S68CP Internal Reducer - 22 x 15
S403WCP (2 Hole) Three Piece - 28 x 15
Conex x Female Thread Matt Chrome Plated - 28 x 22
(Parallel ISO 228) - 35 x 15
Matt Chrome Plated - 35 x 22
- 35 x 28

403WLCP Female Wall Plate Elbow - 22 x 3/4


S403WLCP (3 Hole)
Conex x Female Thread
(Parallel ISO 228)
Matt Chrome Plated

601EQCP Tee - Equal - 12


S601EQCP Conex all Ends 15 15
Matt Chrome Plated 22 22
- 28
- 35

601CP Tee - Reduced - 15 x 15 x 22


S601CP Conex all Ends 22 x 15 x 15 22 x 15 x 15
Matt Chrome Plated - 22 x 15 x 22
22 x 22 x 15 22 x 22 x 15
28 x 15 x 28 -
- 28 x 22 x 28
- 28 x 28 x 15
- 28 x 28 x 22
- 35 x 35 x 15

page 21
®

ISOCONEX For use with MDPE, PB and PE-X Pipe

Part No. Description Size Size Part No. Description Size Size
Brass DZR Brass DZR
S301 Straight Coupler - 20 S403 Female Elbow - 20 x 1/2
Poly x Poly - 25 Poly x Female Thread - 25 x 3/4

- 32 (Parallel ISO 228)

S301 Straight Coupler - 20 x 1/2


New Poly x Old Poly - 25 x 3/4 S403W Female Wall Plate Elbow - 20 x 1/2
(3 Hole)
Poly x Female Thread
(Parallel ISO 228)

S301 Straight Coupler - 20 x 15


Poly x Conex - 25 x 22

S601EQ Tee - Equal - 20


Poly all Ends - 25
- 32

S302 Male Straight Connector - 20 x 1/2

Poly x Male Thread - 25 x 1/2

(Parallel ISO 228) - 25 x 3/4

S617 Tee with Female Branch - 20 x 20 x 1/2

Poly x Poly x Female Thread - 25 x 25 x 3/4


(Parallel ISO 228)

S303 Female Straight Connector - 20 x 1/2


Poly x Female Thread) - 25 x 3/4
(Parallel ISO 228) - 32 x 1

S1201 Lever Ball Valve with Standard - 20 x 20


Red Lever - 25 x 25
Poly x Poly
S323 Stop End - 20
Poly - 25

S1201 Lever Ball Valve with Standard - 25 x 15


Red Lever - 25 x 22
S401 Elbow - 20 Poly (Inlet) x Conex
Poly x Poly - 25
- 32

S402 Male Elbow - 20 x 1/2

Poly x Male Thread


(Parallel ISO 228)

page 22
®

ISOCONEX ACCESSORIES ACCESSORIES For use with Imperial Polythene Pipe


to BS1972 and BS3284

Part No. Description Size Size Part No. Description Size Size
Brass DZR Brass DZR
PY MDPE Liner - 20 50 Adaptor Sleeve - 1/2
- 25 Copper Poly - 3/4

- 32

SC1 Soft Copper Liner - 8


- 10
- 15 51 Ring - 1/2
- 18 Copper Poly - 3/4
- 22

PP PB & PE-X Liner - 10


- 15
- 22 BL Class ‘C’ Insert BS1972/67 - 1/2

- 28 - 3/4

WP2/6 PE-X Insert - 20


- 25
- 32

WP2/10 PE-X Insert - 15


- 20
- 25
- 32

65 Polyring - 20
25
32

S68 Internal Reducer - 25 x 20


Three Piece - 32 x 20
- 32 x 25

SP68 Adaptor - 20 x 15
Poly x Male Copper - 25 x 15
- 25 x 22
- 32 x 28

page 23
®

COPPER TUBULAR TRAPS


Part No. Description Size Size Part No. Description Size Size
Natural Polished Natural Polished
Finish Chrome Plated Finish Chrome Plated

P211 Deep Seal P 1 x 28 1 x 28 P219 Deep Seal P with 11/4 x 35 11/4 x 35


P211PCP Swivel Female 11/4 x 35 11/4 x 35 P219PCP Adjustable Inlet 11/2 x 42 11/2 x 42
Thread x Conex 11/2 x 42 11/2 x 42 Swivel Female Thread
2 x 54 2 x 54 x Conex

S211 Deep Seal S 1 x 28 1 x 28


S211PCP Swivel Female 11/4 x 35 11/4 x 35
Thread x Conex 11/2 x 42 11/2 x 42
2 x 54 2 x 54 P220 Resealing P Antivac Type 11/4 x 35 11/4 x 35
P220PCP Swivel Female 11/2 x 42 11/2 x 42
Thread x Conex 2 x 54 2 x 54

P212 Inlet P - 255mm 1 x 28 1 x 28


P212PCP (10" Long) 11/4 x 35 11/4 x 35
Swivel Female 11/2 x 42 11/2 x 42
Thread x Conex 2 x 54 2 x 54
S220 Resealing S Antivac Type 11/4 x 35 11/4 x 35
S220PCP Swivel Female 11/2 x 42 11/2 x 42
Thread x Conex 2 x 54 2 x 54

P217 Bath P Low Height - 11/4 x 35 11/4 x 35


P217PCP 56mm (21/4") Seal 11/2 x 42 11/2 x 42
Swivel Female P222 Bath P - M/1 11/2 x 42
Thread x Conex 1" Overflow Connection
Swivel Female Thread
x Conex

P218 Vented P 11/4 x 35 11/4 x 35


P218PCP Swivel Female Thread x 11/4 x 35 11/4 x 35
Conex x Male Thread 11/2 x 42 11/2 x 42 P224 Bath P Set - 25mm (1") 11/4 x 35
(Parallel ISO 228) Overflow
Swivel Female Thread
x Conex x Overflow

S218 Vented S 11/4 x 35 11/4 x 35


S218PCP Swivel Female Thread x 11/4 x 35 11/4 x 35
Conex x Conex 11/2 x 42 11/2 x 42
2 x 54 2 x 54
P225 Resealing Bath P Set - 11/4 x 35
25mm (1") Overflow
Swivel Female Thread
x Conex x Overflow

page 24
®

COPPER TUBULAR TRAPS BOTTLE TRAPS


Part No. Description Size Size Part No. Description Size Size
Natural Polished Natural Polished
Finish Chrome Plated Finish Chrome Plated

P314 Running P 28 28 160C Fixed Inlet - Fabricated 3/4 x 22 3/4x 22


P314PCP Conex x Conex 35 35 160CPCP Swivel Female 1 x 28 1 x 28
42 42 Thread x Conex 11/4 x 35 11/4 x 35
54 54 11/2 x 42 11/2 x 42

S314 Running S 28 28 160M Fixed Inlet - Fabricated 3/4 3/4


S314PCP Conex x Conex 35 35 160MPCP Swivel Female Thread x 1 1
42 42 Male Thread (Parallel) 11/4 11/4
54 54 11/2 11/2

Cleaning Eye 3/8 160RC Resealing with Fixed Inlet 11/4 x 35 11/4 x 35
Extra Charge Cleaning eye 160RCPCP (5" Seal) Fabricated 11/2 x 42 11/2 x 42
plug and washer Swivel Female Thread
2 side cleaning x Conex
eyes, plugs &
washers

160RM Resealing with Fixed Inlet 11/4 11/4


160RMPCP (5" Seal) Fabricated 11/4 11/4
Swivel Female Thread x
Male Thread (Parallel)

16030 Chrome Plated Brass with 11/4 x 35


Adjustable Inlet 11/2 x 42
Swivel Female Thread
x Conex

page 25
®

TRAPS - WASTE FITTINGS

Part No. Description Size Size Part No. Description Size Size
Natural Polished Natural Polished
Finish Chrome Plated Finish Chrome Plated

W301 Straight Coupler 35 35 W601S Sweep Tee 35 35


W301PCP Conex x Conex 42 42 W601SPCP Conex all Ends 42 x 42 x 35 42 x 42 x 35
54 54 42 42
54 x 54 x 35 54 x 54 x 35
54 x 54 x 42 54 x 54 x 42
54 54

W302 Male Straight Connector 35 x 11/4 35 x 11/4


W302PCP Conex x Male Thread 42 x 11/2 42 x 11/2
(Parallel ISO 228) 54 x 2 54 x 2

DP200 Down Pipe Extended - 11/2 x 42 11/2 x 42


D200PCP 200mm (8") Long 2 x 54 2 x 54
Fabricated
Swivel Female Thread
x Plain Tail
W303 Female Straight Connector 35 x 11/4 35 x 11/4
W303PCP Conex x Female Thread 42 x 11/2 42 x 11/2
(Parallel) 54 x 2 54 x 2

W333 Inlet Extension 2 2


W333PCP Tail Pipe -
W401F Elbow - Fabricated 35 35 127mm (5") Long
W401FPCP Conex x Conex 42 42 Fabricated
54 54 Male Thread (Parallel)
x Swivel Female
Thread

W412 Extended Bath Overflow - 35 x 11/4 35 x 11/4


W401FT Elbow with Cleaning Eye - 35 35 W412PCP 406mm (16") Long
W401FTPCP Fabricated 42 42 Fabricated
Conex x Conex 54 54 Plain Tail x Overflow

W432 Bent Tail Pipe Extended - 11/4 x 35 11/4 x 35


W401/0F Obtuse Elbow - Fabricated 35 35 W432PCP 406mm (16") Long 11/2 x 42 11/2 x 42
W401/0FPCP Conex x Conex 42 42 Fabricated
54 54 Swivel Female Thread
x Plain Tail

W610 Extended Tee - 35 35


W403SF Swivel Elbow - Fabricated 35 x 11/4 35 x 11/4 W610PCP 914mm (36") Long 42 42
W403SFPCP Conex x Swivel 42 x 11/2 42 x 11/2 Fabricated 54 x 54 x 35 54 x 54 x 35
Female Thread 54 x 2 54 x 2 Conex x Plain Tail 54 x 54 x 42 54 x 54 x 42
x Conex

page 26
®

TRAPS - ACCESSORIES TRAPS - MANIFOLDS

Part No. Description Size Size Part No. Description Size


Natural Polished
Finish Chrome Plated

W63 Capnut 35 35 190 Gunmetal Bath Overflow


W63PCP 42 42 Manifold 11/4
54 54 Compression Outlet, with
Chrome Plated Nozzle and
Face Plate

W63B Blank Capnut 1 1


W63BPCP 35 35 190PC Gunmetal Overflow Manifold 11/4
42 42 As 190 with Plug and Chain
54 54

W65 Brass Compression Ring 35 -


42 -
54 -

191 Plastic Overflow Manifold 11/4


ABS Body, MI Outlet,
Chrome Plated
Plastic Face Plate and Nozzle

W65P Plastic Compression Ring 11/4 -


11/2 -
2 -
35 -
42 -
54 -

191PC Plastic Overflow Manifold 11/4


As 191 with Plug and Chain
W68 Internal Reducer 35 x 28 35 x 28
W68PCP Three Piece 42 x 28 42 x 28
42 x 35 42 x 35
54 x 28 54 x 28
54 x 35 54 x 35
54 x 42 54 x 42

191CL Plastic Overflow Manifold 11/4 x 1


As 191 with Cap and Lining
99 Rubber Washer 35 -
Use with W63B 42 -
54 -

18016 Inlet Joint Washer 11/4 -


Use with Swivel Female 11/2 - Nut and Lining
Thread Connections 2 - 195 Plastic Cap and Lining 11/4 x 1
(Use with 191PC, 190, 11/4 x 11/4
190PC and 191)

page 27
®

STOP VALVES / CHECK VALVES FULLWAY GATE VALVES TO BS5154/B


Part No. Description Size Size Part No. Description Size Size
Brass DZR Wheelhead Lockshield
701 Stop Valve - Crutch Head 15 15 1001 Brass Gate Valve (PN16) 15 15
S701 Conex x Conex 22 22 1001LK Conex x Conex 22 22
28 28 28 28
35 - 35 35
42 - 42 42
54 - 54 54

1001CP Chrome Plated Brass Gate 15 -


Valve (PN16) 22 -
701CP Chrome Plated Stop Valve - 15 - Conex x Conex
Crutch Head 22 -
Conex x Conex

1101/100 DZR Gate Valve 67.7 -


Conex x Conex 76.1 -
T480Y Single Check Valve - 3/8

Female Thread x Female - 1/2

Thread - 3/4

- 1
- 11/4
- 11/2
- 2

DRAINING TAPS SERVICEMAN VALVES TO BS6675


Part No. Description Size Size Part No. Description Size
Brass DZR Brass Nickel Plated
S742 DZR Draining Tap to - 1/2 720NP Straight Servicing Valve 15 x 10
BS2879-2 1980 (Bushed) Conex x Conex 15 x 15
Male Thread (Parallel 22 x 22
ISO 228)

721NP Servicing Valve Elbow 15 x 1/2


S746 DZR Draining Tap (Bushed) - 15
Conex x Conex Conex x Swivel Female Thread
(Parallel ISO 228)

3/4 722NP Straight Servicing Valve 15 x 1/2


1350 Draining Tap Key -
Conex x Swivel Female Thread 22 x 3/4

42500KY Lockshield Key for 15 -


Gate Valves 22 -

page 28
®

PLUG TAPS / AUTOMATIC AIR VENT /


WASHING MACHINE VALVE LEVER BALL VALVES
Part No. Description Size Part No. Description Size Size
Brass Brass Natural DZR
Finish Natural Finish
1501 Plug Tap 15
Conex x Conex 22
1201 Lever Ball Valve with 15 15
S1201 Standard Red Lever 22 22
Conex x Conex 28 28

3620 Automatic Air Vent 3/8


S1201 ISO Lever Ball Valve with - 20 x 20
Standard Red Lever - 25 x 25
Poly x Poly

S1201 ISO Lever Ball Valve with - 25 x 15


3/8 Standard Red Lever - 25 x 22
3625 Air Vent Isolator
Poly (Inlet) x Conex

1211 Lever Ball Valve with Red 15 -


‘T’ Handle 22 -
Conex x Conex 28 -

BRASS FLOAT VALVES


Part No. Description Size Size
Part No. Description Size Brass Brass Nickel
Brass Nickel Natural Finish Plated
Plated
1204 Lever Ball Valve with 1/2 -
Brass Float Valve
Standard Red Lever 3/4 -
BS 1212: Part 1
Side Entry Female Thread 1 -
50033 1/2 (Parallel ISO 228) x 11/4 -
50033L High Pressure Plastic Seat 3/4 Female Thread 11/2 -
50033J 1 (Parallel ISO 228) 2 -

50063 Low Pressure Plastic Seat 1/2

50133S High Pressure Metal Seat 11/4


1204G Lever Ball Valve with 1/4 -
11/2
Standard Yellow Lever 3/8 -
2
Female Thread
(Parallel ISO 228) x 1/2 -
Brass Float Valve Female Thread
(Parallel ISO 228) 3/4 -
BS 1212: Part 2
Side Entry

52033 High Pressure 1/2

52063 Low Pressure 1/2


1204W Light Pattern Nickel - 1/2

Plated Lever Ball Valve - 3/4

with Standard Red Lever - 1


Female Thread - 11/4
563 Plastic Float Valve (Parallel ISO 228) x - 11/2
BS 1212: Part 3 Female Thread - 2
Side Entry - Supplied with 2 seats (Parallel ISO 228)
H.P (Fitted) and M.L.P

All Plastic High Pressure 1/2

page 29
®

Notes

page 30
IBP GmbH
Erdkauter Weg 17
D-35394 Giessen
GERMANY
Tel: +49 641 70070
Fax: +49 641 7007361

IBP Atcosa S.L.


Poligono Industrial Quintos-
Aeropuerto Apartado Correos 16
14005 Cordoba
SPAIN
Tel: +34 957 469600
Fax: +34 957 469604

IBP France
Immeuble P H Spaak
12 rue Jules Ferry
93561 Rosny-sous-Bois Cedex
FRANCE
Tel: +33 1 481 22550
Fax: +33 1 481 22560

IBP Bänninger Italia Srl


Strada Provinciale Asolana No. 92
43056 San Polo di Torrile (Parma)
ITALY
Tel: +39 0521 317311
Fax: +39 0521 317355

IBP Limited
Whitehall Road
Tipton
West Midlands DY4 7JU
UNITED KINGDOM
Tel: +44 (0)121 557 2831
Fax: +44 (0)121 520 8778
email: salesuk@ibpgroup.com
technical@ibpgroup.com
web: www.ibpgroup.com

IBP Instalfittings SP z o.o


ul Obodrzycka 61
61-249 Poznan
POLAND
Tel: +48 61 8 770051
Fax: +48 61 8 790949

RMA T 05/04 CONEX

You might also like