FATIGUE OF METALS 403
usually plotted in terms of nominal stress based on the net section of the
specimen. The effectiveness of the notch in decreasing the fatigue limit is
expressed by the fatigue-strength reduction factor, or fatigue-notch factor, K, This
factor is simply the ratio of the fatigue limit of unnotched specimens to the
fatigue limit of notched specimens. For materials which do not exhibit a fatigue
limit the fatigue-notch factor is based on the fatigue strength at a specified
number of cycles. Values of K, have been found to vary with (1) severity of the
notch, (2) the type of notch, (3) the material, (4) the type of loading, and (5) the
stress level. The values of Ky published in the literature are subject to consider-
able scatter and should be carefully examined for their limitations and restric-
tions. However, two general trends are usually observed for test conditions of
completely reversed loading. First, K, is usually less than K,, and second, the
ratio of K,/K, decreases as K, increases. Thus, very sharp notches (high K,) have
less effect on fatigue strength than would be expected from their high value of K,,
The notch sensitivity of a material in fatigue is expressed by a notch-sensitiv-
ity factor q
K,-1
(12-27)
Equation (12-27) was chosen so that a material which experiences no reduction in
fatigue due to a notch (K, = 1) has a factor of q = 0, while a material in which
the notch has its full theoretical effect (K, = K,) has a factor of q = 1. However,
q is not a true material constant since it varies with the severity and type of notch
(Fig. 12-19), the size of specimen, and the type of loading. As Fig. 12-19 indicates
notch sensitivity increases with tensile strength. Thus, it is possible in certain
circumstances to decrease fatigue performance by increasing the hardness or
tensile strength of a material.
1.9)
°
* os
> 0.6
S “ Quenched and tempered stee!
5 Anneoled ond normalized steel
§ 04) ‘Aluminum alloy
3 02]
2
°
0 05 10 15 20 25 30 35 40 45 60
mm
Figure 12-19 Variation of notch-sensitivity index with notch radius for materials of different tensile
strength. (After R. E. Peterson, in G. Sines and J. L. Waisman (eds., “Metal Fatigue,” p. 301, McGraw-
Hill Book Company, New York, 1959. By permission of the publishers.)404 APPLICATIONS TO MATERIALS TESTING
Table 12-1 Some values of
Neuber’s constant p”
Strength level, p's
Material MPa mm
Steel ous
0.07
001
Aluminum. 2
alloy 06
04
Another approach to notch sensitivity in fatigue was advanced by Neuber.!
He expressed the fatigue stress concentration factor as
(12-28)
where r= contour radius at the root of the notch
p’ =a material constant related to the strength of the metal. See Table 12-1
for some values of p’.
The above relationships express the fact that, for large notches with large radii,
K, is almost equal to K,, but for small notches we find K, < K, for soft ductile
metals and K, higher for stronger metals. We say these are more notch sensitive.
In the absence of data, an estimate of the notched fatigue strength can be
made by constructing a straight line on a semilogarithmic S-N plot from the
ultimate tensile strength at a life of one cycle to the unnotched fatigue strength
divided by K, at 10° cycles.
For design purposes, in ductile materials K, should be applied only to the
alternating component of stress and not to the steady component of stress when
6, # 0. For fatigue of brittle materials K, should also be applied to the steady
component of stress.
Example A shaft with a transverse oil hole is subjected to a fluctuating
bending moment of +40 N m and an axial steady load of 20 kN. The
diameter of the shaft is 12 mm and the diameter of the hole is 1.2 mm. This
situation is shown in Fig. 2-21e, where a/d = 0.10 and K, = 2.2. If the shaft
is made from steel with S, = 1310 MPa, then from Table 12-1 p’ = 0.01 mm
1H. Neuber, “Theory of Notch Stresses,” J. W. Edwards, Publisher, Incorporated, Ann Arbor,
Mich. 1946FATIGUE OF METALS 405
and \/p’ = 0.01. Since r = 0.6 mm
&,-1 22-1 ia
1 =1+—— = 2063
1+ Jor 1+,/0.01/06 1+ 0.129
K,-1_ 1.063
aif.
a= ay 70886
‘The mean or steady stress is
fears =
On = P= Gaya 7 O77 KN mm“? = 17 MPa
The fluctuating bending stress is
M(D/2 40 x6
xf F |= 2.063 oa = 0486 Nm mm~>
64 | = 0.486 x 10° N m=? = 486 MPa
The effective maximum stress is given by
max = Tq + Fm = 486 + 177 = 663 MPa
= 486 — 177 = 309 MPa
A good estimate of the unnotched fatigue limit is S,/2 = 655 MPa. The
S-N curve can be estimated as follows
and Gan gt ae
1400
+200
= Unnetched
é 1000
é i
5 oe <=
3 jotche
= SN =
§ 600
8 or 4
8 200 .
"00 ieee ate
ou/ Ky
o 4
1 10 Ose) 05 tiger] 08 HOSO;
Cycles to failure
Using the equation for the Goodman line, Eq, (12-7)
6, on) 655 17
ef a) Oe ee) 75 MP
a (1 22) Bal a) Hels)