Professional Documents
Culture Documents
Engineering
case study
UNIT 10
Part 1
Roller coaster engineering
b A well-known type of amusement park ride is the roller coaster. Write a non-
technical definition, of 20 to 30 words, to describe a roller coaster in the space
provided. Use some or all of the words in the box below to help you.
bend corkscrew curve
down loop slope steep track train up
Roller coaster:
Part 2
a The words in 1–10 below are physics terms which can be used to describe how
roller coasters work. Match them to the descriptions in a–j.
1 heat energy a energy in the form of movement
2 kinetic energy b energy stored in things that are hot
3 potential energy c stored energy that will allow an object to move (fall)
due to gravity
4 G-force d speed in a certain direction
5 centrifugal force e increase speed
6 velocity f reduce speed
7 friction g pushes things outwards as they turn
8 inertia h pushing/pulling due to acceleration/deceleration
9 decelerate i resistance generated when two surfaces rub together
10 accelerate j resistance to acceleration or deceleration due to an
object’s mass
b Complete the science magazine article on page 2 about how roller coasters work,
using the physics terms from Exercise a (1–10).
Roller
coasters:
how they work
On a traditional roller coaster, the train begins by going slowly
up a steep slope at the start of the track. Generally, the train is
pulled up this slope by a moving chain located below the track,
which is driven by an electric motor. When the train reaches the top
of the slope, it has (1) . This means it has
the ability to descend due to the force of gravity. Therefore, the train
can now produce (2) (that is, movement)
without needing more power from the motor.
The next section of track has a steep downward slope. This allows the
train to (3) , increasing its (4) as it goes
down the slope. This, together with the mass of the train and passengers,
gives the train enough (5) to coast for a fairly long
distance, without power. The rest of the track can include upward and
downward slopes, curves, loops and corkscrews. These exert forces of
resistance, which progressively cause the train to (6) .
These forces are:
l g ravity, causing resistance as the train goes up slopes
l (7) – the resistance of the wheels rubbing against
the track and against their bearings and axles. This converts
kinetic energy to (8) , increasing the
temperature of the wheels. Roller coasters do not only have wheels
running on top of the rails. They also have ‘upstop wheels’ below the
rails and ‘guide wheels’ at the sides of the rails, to hold the train on
the track.
On sections of track with curves and loops, friction is greatly increased
by (9) , which tries to push the train
outwards as it turns. This presses the wheels hard against the track,
generating high frictional resistance and, as a result, high temperatures.
This force also pushes the passengers into their seats, generating the
(10) that roller coasters are famous for.
Part 3
Using the information in the article and your own technical knowledge, talk to a
partner about the design of roller coaster wheels. Then give a short talk to sum
up your thoughts. Discuss:
1 the different forces and conditions the wheels, axles and bearings of the train need
to cope with
2 the implications of using larger or smaller wheels
3 the suitability of wheels made from different materials
The following sections from Cambridge English for Engineering may be useful.
●● Unit 2 – Describing specific materials (pages 14 and 15), Categorising materials
(pages 16 and 17) and Specifying and describing properties (pages 18 and 19)
●● Unit 5 – Describing types of technical problem (pages 38 and 39)
●● Unit 9 – Discussing causes and effects (pages 76 and 77)
●● Unit 10 – Discussing performance and suitability (pages 78 and 79), Describing
physical forces (pages 80 and 81) and Describing capabilities and limitations
(pages 84 and 85)
Part 4
a Read the article extract, below, about ‘launched roller coasters’. Sum up how
these are different to traditional roller coasters.
Many 21st century roller coasters differ from traditional rides in one way:
they are ’launched‘. This means that, instead of being slowly pulled up the
first slope by a chain, the roller coaster has a powerful launching system
to accelerate the train rapidly along a flat section at the start of the
track. This gives the train enough inertia to climb the first steep slope.
Kingda Ka, the world’s fastest and tallest roller coaster at Six Flags Great
Adventure in New Jersey, USA, has a launch system which accelerates
the train from 0 to over 200 km/h in 3.5 seconds – an acceleration of
about 1.5 G.
b Now imagine you are back in the 1990s, when the first launched roller coasters
were developed. You and your partner are research and development (R&D)
engineers working for a roller coaster manufacturer. Come up with some ideas –
in general terms – for suitable types of launch system. The systems should be:
●● safe and reliable
●● powerful enough to produce an ‘exciting’ amount of acceleration
●● cost-effective to operate and maintain.
Engineering
TEACHER’S NOTES
UNIT 10
Part 1
Roller coaster engineering
Part 2
Students complete both tasks in pairs.
Answers
a 2 a 3 c 4 h 5 g 6 d 7 i 8 j 9 f 10 e
b 1 potential energy 2 kinetic energy 3 accelerate 4 velocity
5 inertia
6 decelerate 7 friction 8 heat energy 9 centrifugal force
10 G-force
Part 3
Ask students to read the article extract in Part 2 again. Focus on the meaning of
the following terms in the text:
axle /ˈæk.sƖ/ a shaft (bar) connected to the centre of a wheel or connecting a pair of
wheels, and also connected to the chassis of a vehicle (a short axle for just one wheel
is sometimes called a stub axle)
bearing /ˈbeə.rɪŋ/ a part fixed around a shaft at the point where the shaft is connected
to a machine or chassis, allowing the axle or shaft to spin with a minimum of frictional
resistance and wear (bearings often contain metal balls, called ball bearings, which are
designed to roll)
Students then complete the task in pairs, then report back to the group with
their thoughts.
Suggested answers
1 The surfaces of the wheels that are in contact with the track, and also the
points of contact between the wheels, bearings and axles, need to be able to
resist friction.
The wheels also need to cope with the heat generated by friction.
The wheels, bearings and axles have to cope with the forces of expansion and
contraction as they continually heat up, due to friction, and then cool down as
the roller coaster repeats the ride cycle.
The wheels must resist the centrifugal force of the wheel itself spinning.
This will generate tension (stretching force) as the centrifugal force tries to
push the material of the wheel outwards (like the pastry of a pizza stretching
outwards as the cook spins it round).
The wheels and bearings must also resist compression (crushing force) when
they are forced against the rails by the centrifugal force acting on the train as
it turns through curves and loops.
The axles need to cope with shear force (scissoring force) as the train is forced
against the track as it turns through curves and loops.
2 The main advantage of smaller wheels is that they are more compact, making
them easier to fit below the train. Smaller wheels also reduce the total mass
of the train – although this isn’t necessarily an advantage, as a roller coaster
train needs mass to give it inertia to keep it rolling. Another advantage of
smaller wheels is that their thickness is greater relative to their diameter – i.e.
they are less slender than larger wheels of the same thickness. ‘Taller’, more
slender wheels would buckle more easily when compressed against the rails.
The disadvantage of smaller-diameter wheels is that, for a given velocity, they
spin faster than larger wheels. This creates more frictional resistance (greater
speed = greater friction) and, as a result, generates higher temperatures. The
centrifugal force caused by the wheel itself spinning is also higher with smaller
wheels, due to the higher rotational velocity.
3 Strong metal, such as steel, is a good material for resisting the different
forces acting on the wheels. However, metal-only wheels running on the
metal track would be problematic, as they would be noisy, transmit a lot of
vibration to the train and passengers, and would also cause the track (which
is expensive to replace) to wear quite quickly. Solid tyres made from polymers
(plastics), such as polyurethane, are better, as they give a quieter, softer ride,
don’t wear the track and can be replaced fairly cheaply. The disadvantage of
polyurethane on extreme roller coasters is that it can get too hot and melt.
Instead, especially tough rubber can be used, similar to that used in aircraft
tyres (which need to cope with high levels of friction on landing).
Part 4
a Students read the article extract and complete the task. You could follow up by
showing a ‘front seat’ video of the Kingda Ka roller coaster:
http://www.youtube.com/watch?v=xTNcnJS-a2M&feature=fvsr