Professional Documents
Culture Documents
1/4X 1/a
~
1/a .876 10-32 13/a 9132
2 3/4 2.751 5
/s x 5/15 3fs -16 3 3/4 9132
500A 16 6 3la 3.124 'l4x% 42M 36:V. 4334 38 45% 3834 23 13.500 34 2411 1}{, 131is +25}2 14'!<0 %-11-NC 3 % % 1"'As 4Y2 2% % 7% 7% 2~s
600A 16 6 3~ 3.749 :V.x ~s 42:V. 36:V. 4334 38 45% 3834 23 13.500 34 2411 1}{, 131is +25¥. 14'!<0 %-11-NC 3 % % 1"'118 4Y2 2% % 7% 7% 2~s
750A 18 6 3% 3.749 :V.x ~. 48 41% 50 42 50 42o/1s 23 13.500 34 24¥. 1}{, 131is +26"A 14'!<0 %-11-NC 3 1 1 1"'118 6 2:V. "A 834 834 2~s
1000G 21 8 4 3.998 1xY2 62 )' 50 34 6234 50 34 6234 5034 28% 22.000 34 3011 1 34 '"As 36:V. 26 "A-10-NC 3% % % 25As 634 3% % 8 8Y2 2 15As
t"XA" dimensions shown apply to 1:1 and speed increasing ratios only. Request certified drawing for others.
*Models 300 and 350 furnished with external heat exchanger.
**Contact factory for maximum coupling bore for Fig. 2 or Fig. 3 rotation with 1:2 or 1:3 ratio.
RATIOS AND ROTATIONS: The ratio of a drive is defined as the ratio of the horizontal input speed to vertical output speed. For example, a 2:1 ratio would have a
horizontal speed of twice the vertical speed. There are four rotational schemes available as shown in figures 1, 2, 3, and 4. Figure 1 is denoted as standard rotation.
Figures 2, 3, and 4 are special rotation, being manufactured only on order, and are not subject to cancellation without charge for completed parts.
JIF'
Vertical Shaft Percent of Percent of Vertical Shaft Percent of Percent of
R.P.M. Rated Horsepower Thrust Capacity R.P.M. Ratad Horsepower Thrust Capacity
430 37% 160% *2000 107% 96%
580 46% 145% *2200 112% 93%
690 52% 137% *2400 117% 90%
HORIZONTAL • CW 720 53% 135% *2600 122% 88%
VERTICAL • CCW 870 61% 126% *2800 128% 86%
960 65% 122% *3000 134% 84%
1160 75% 115% *3460 146% 80%
1460 88% 106% *3600 150% 79%
1760 100% 100%
* Cooling coils should be specified for models 40, 60A, and BOA operating at speeds
HORIZONTAL • CCW HORIZONTAL· CCW above 1760 rpm. Consult with the factory on all applications when the vertical speeds
VERTICAL • CCW VERTICAL • CW
exceed 1760 rpm. Maximum allowable cooling water pressure for cooling coils is 100 psi
CW - Clockwise; CCW - Counterclockwise. and heat exchanger is 150 psi.
An Introduction To Our Company
In 1934, Amarillo Gear Company began designing and manufacturing Spiral Bevel Right Angle Gear Drives primarily for the
irrigation industry. Because of the reliable, efficient and economic operation of these drives, they met with widespread acceptance.
Today, we manufacture the largest selections of RightAngle Gear Drives available. Our standard models include a large assort-
ment of drives in a wide range of ratios and various configurations. They are highly adaptable to many applications in many
different industries.
One reason for the continued growth and acceptance of Amarillo Gear Drives is their consistent quality- not only in the
materials used, but in their workmanship as well.
We would welcome the opportunity to supply our product for your requirements.
FEATURES:
Cooling coils are available on Models 40, 60A, and BOA, at additional cost. and are standard on Model1 OOA and above. Non-reverse
clutches are standard on all drives. Marine options are available upon request.
Our rigid castings are designed to insure correct alignment. Gears are case hardened alloy steel, lapped in pairs. All drives
have positive oil pressure distribution systems. All bearings used in construction are name brand and high quality, with
proven reputations for reliability; providing bearing life exceeding AGMA recommendations.
~All standard hollow shaft gear drives through Model1200 are approved by FACTORY MUTUAL for use with vertical
~fire pumps.
APPROY~D SPECIAL DRIVES
Drives listed in this catalog may also be available with additional options. Please contact the factory for availability and pricing
of these options. For applications that require power ratings larger than listed in this catalog, please visit our website at
www.amarillogear.com, under the tabs for Large Pump and Large Flood. Literature for these larger models can be selected
directly from the website.
Amarillo Gear Company reserves the right to make improvement modifications to our gear drives that may change the given dimensions. The dimensions
shown in this brochure may not exactly reflect the dimensions of the gear drives currently being offered. Request a Certified Dimensional Print for
construction use.
WEIGHTS AND BOX DIMENSIONS
MODEL NET DOMESTIC EXPORT BOX EXPORT BOX DIMENSIOI S (Inches) VOLUME
WEIGHT (lbs.) SKID (lbs) Pounds Kilograms Length Width Height CUBIC FEET
30 92 110 125 57 22 14 21 4
40A 220 240 275 125 27 15 27 6
408 230 260 310 141 29 18 27 8
BOA 325 350 390 177 29 19 34 11
BOA 345 370 410 186 29 19 34 11
100A 125A 385 390 430 195 29 19 34 11
150A 430 450 505 229 31 19 38 12
200A 630 675 810 368 35 24 42 20
250 300 350 760 805 900 408 36 24 40 21
450A 1340 1420 1620 735 44 32 52 42
500A 1370 1450 1650 748 44 32 52 42
600A 1365 1465 1665 755 44 32 52 42
750A 1800 1890 2165 962 45 32 57 48
1000G 2650 3055 3310 1501 56 37 74 92
T.M
Catalog PD 1/14
Amari lid~ Gear Company LLC
Post Office Box 1789 • Amarillo, Tx 79105 • 2401 Sundown Lane (79118) • 806-622-1273 • Fax 806-622-3258
www.amarillogear.com e-mail: info@amarillogear.com © AGC 2014
DJ
I II. A Marmon Water/Berkshire Hathaway Company