6 Junction between the large end of a cone and a cylinder without a knuckle
The mean diameter of the cylinder at the junction with
the cone: Dc 1010 [mm] The semi angle of come at apex: α 30 [°] The calculation pressure: P 0,6 [Mpa] The test pressure: Ptest 0,9 [Mpa] The minimum yield strength or 0,2% proof strength at calculation temperature: Rp0,2T 355 [Mpa]
The minimum tensile strength at 20°C: Rm/20 450 [Mpa]
Joint coefficient: z 0,7 []
The nominal design stress for normal operating cases:
𝑅 , 𝑓 = 1,05 ftest 338,1 [Mpa] Required thickness at a junction at the large end of a cone: 1 𝐷 tan 𝛼 𝛽= − 0,15 3 𝑒 1+ 1 cos 𝛼 𝑃∗𝐷 ∗𝛽 𝑒 = 2𝑓 𝑃 ∗𝐷 ∗𝛽 𝑒 = 2𝑓 ej 4 [mm]
Nominal thickness according to 7.4.2: en=ecyl 10 [mm]
Nominal thickness according to 7.6.4: en=econ 10 [mm]
Analysis reinforcing thickness in cylinder: e1a 10 [mm]
Analysis reinforcing thickness in cone: e2a 10 [mm]
Required thickness of cylinder at junction:
𝑒 ≥ 𝑒 = 𝑚𝑎𝑥 𝑒 ,𝑒 e1 10 [mm]
Required thickness of cone at junction:
𝑒 ≥ 𝑒 = 𝑚𝑎𝑥 𝑒 ,𝑒 e2 10 [mm] The corrosion allowance: c 2 [mm] The absolute value of the possible negative tolerance on the nominal thickness (EN 10029): quality D de1 0,7 [mm]
Limit values of weld joint defects (EN ISO 5817): quality D
Linear offset between plates (EN 5817): 𝐵 → 𝛿 = 𝑚𝑖𝑛 0,2 + 0,1𝑚𝑖𝑛 𝑒 , 𝑒 ; 3 𝐶 → 𝛿 = 𝑚𝑖𝑛 0,2 + 0,15𝑚𝑖𝑛 𝑒 , 𝑒 ; 4 𝐷 → 𝛿 = 𝑚𝑖𝑛 0,2 + 0,25𝑚𝑖𝑛 𝑒 , 𝑒 ; 5 de2 2,7 [mm] Defects of welds: 𝐵 → 𝛿 = 0,2 ∗ 𝑚𝑖𝑛 𝑒 , 𝑒 ∗ 0,04 𝐶 → 𝛿 = 0,3 ∗ 𝑚𝑖𝑛 𝑒 , 𝑒 ∗ 0,08 𝐷 → 𝛿 = 0,4 ∗ 𝑚𝑖𝑛 𝑒 , 𝑒 ∗ 0,16 de3 0,6 [mm] Analysis thickness at a junction at the large end of a cone: 𝑒 = 𝑚𝑖𝑛 𝑒 , 𝑒 −𝑐−𝛿 −𝛿 −𝛿 ej 4,0 [mm] Coefficient: 1 𝐷 tan 𝛼 𝛽= − 0,15 3 𝑒 1+ 1 cos 𝛼