Professional Documents
Culture Documents
RESERVOIR ENGINEERING I
by
Val Pinczewski
March, 2002
Prepared for
This copy of the manual and accompanying software was prepared in accordance
with copyright laws for the sole use of students enrolled in a course at the Uni-
versity of New South Wales. It is illegal to reproduce any of this material or to
use it for any other purpose.
2
Contents
1 INTRODUCTION 7
2 RESERVOIR DESCRIPTION 23
1
2.2.3 Pressure and Production Testing . . . . . . . . . . . . . . 38
2
4.3 GEOTHERMAL GRADIENT . . . . . . . . . . . . . . . . . . . . 84
5 FLUID PROPERTIES 86
3
6.1.1 Gas Cap Expansion . . . . . . . . . . . . . . . . . . . . . . 135
4
7.3.2 Fractured medium model . . . . . . . . . . . . . . . . . . . 185
8.2.4 Relationship between s and the size of the altered zone . . 210
5
8.5 GAS FLOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
6
Chapter 1
INTRODUCTION
For those unfamiliar with reservoir engineering or reservoir geology the following
section gives a brief summary of some basic concepts. If you are familiar with
this material skip this section.
The depositional energy at a particular location varies with time. This results in a
sequential deposition of sand (large particles) and shale (fine particles) producing
sequences of sand and shale. (layering). This layering or vertical heterogeneity is
the single most important characteristic determining reservoir performance and
recovery.
7
Figure 1.1: Schematic of a typical depositional sequence
8
1.1.2 Origin of Petroleum
The precursors of petroleum, organic matter from dead plants and animals, are
deposited together with fine-grained sediments in shallow marine environments
during low energy periods of basin formation. Quite water is deficient in oxygen
leading to the creation of anaerobic conditions and preservation of the organic
matter. Anaerobic bacteria decomposes the organic matter to produce com-
pounds of carbon, hydrogen (hydrocarbons) and oxygen. The conversion of the
organic matter occurs over geological time as sediments become progressively
buried and temperature and pressure increase.
The minimum temperature for oil and gas formation is about 150o F and the
maximum is about 320o F. Since temperature increases with depth, this results in
a burial depth window of between 7,000 ft to 23,000 ft for fine grained sediments
containing organic matter (source rocks) to produce oil and gas.
The expelled hydrocarbon is lighter than the water in the interconnected pore
space of the permeable sand layers and moves upwards as a result of buoyancy.
This is called secondary migration. The upward migration of generated hydrocar-
bon continues until it is halted by an impermeable barrier or trap. As hydrocarbon
accumulates under the trap a reservoir is formed.
Here are some commonly used terms to describe petroleum reservoirs. You will
probably be familiar with most of these terms.
9
Figure 1.2: Cross-section for an anticlinal reservoir
Formation: the rocks, These may be either clastic rocks (sandstones) or lime-
stone and dolomite (carbonates).
Spill point: the lowest point of the trap that can hold hydrocarbon.
Trap closure: the distance between the crest and the spill point.
Reservoir: the part of the formation which contains hydrocarbon (oil and/or
gas) and connate water.
Water zone or aquifer: the body of water bearing rock in hydraulic commu-
nication with the reservoir.
10
Figure 1.3: Anticline structural trap
Structural traps
11
Figure 1.5: Salt dome structural trap
Stratigraphic traps
Stratigraphic traps are produced by facies (rock type) changes in the formation
such as pinchouts and lenticular sand bodies surrounded by impermeable shales.
The processes involved in the formation of stratigraphic traps are complex because
they involve changes in the depositional environment.
Study the attached figures in the context of the above discussion. This will
improve your understanding of the basic concepts. Note the following important
points in the last of the figures:
(i) The oil and gas zones in the central block are not in direct pressure com-
munication with the oil and gas zones in the left and right blocks. The oil
and gas zones have different contacts.
(ii) However, it cannot be concluded from the section alone that the central
block is completely isolated from the rest of the formation. The blocks may
be in pressure communication through the aquifer.
12
Figure 1.6: Stratigraphic trap
Figure 1.7: Schematic of an oil and gas reservoir with a faulted central block and
different fluid contacts
13
Figure 1.8: USA oil resource
An EOR process is any process which does a better job of recovering oil than
conventional technology (primary and secondary recovery processes). In an EOR
process conventional water or gas is replaced by a more effective (more expensive)
recovery agent.
14
1.2.1 Residual Oil Resource (Target for EOR )
Conventional primary recovery methods are usually very inefficient and, on the
world average, recover approximately 1/3 of the OOIP.
- current EOR technology can produce about 20% —30% of the residual oil
resource.
- Trapping on the macro or field scale is caused by areal and vertical by-
passing.
Unrecovered oil may be classified into two categories: Unrecovered mobile oil and
immobile or residual oil.
- infill drilling.
- horizontal and multilateral wells.
- removal of formation damage caused by completion operations.
- fracking.
- perforating unperforated layers.
- selective shut-off of water and gas producing zones.
15
Figure 1.9: Residual is trapped or bypassed on all reservoir length scales
16
Figure 1.10: Recovery processes
17
For example:
(i) Thin, flat reservoirs with low permeability will most likely produce by a
solution-gas drive mechanism.
(ii) Reservoirs having high closure and high permeability may experience the
beneficial effects of gravity segregation of oil and gas. This may supplement
the effectiveness of the original gas cap, or form a secondary gas cap.
(iii) High permeability reservoirs in contact with an extensive aquifer will benefit
to some degree from natural water influx (water drive).
(i) The size of the gas cap relative to the size of the oil reservoir.
(ii) The size of the aquifer relative to the size of the oil zone.
(iii) Formation permeability can be estimated from core data and flow tests on
wells.
Drill-stem tests on dry holes and structurally low wells (wells penetrating the
aquifer) may yield important indications of aquifer permeability and continuity.
Sometimes it is useful to complete dry holes as aquifer observation wells. Pressure
data from such wells can be important in characterizing reservoir-aquifer systems.
The aquifer can have a profound effect on reservoir performance.
18
Figure 1.11: Steam flooding process
The same techniques used to determine the need for secondary recovery are used
to assess the need for tertiary developments. Decisions regarding the actual im-
plementation of EOR processes are not made until sufficient field data is available
to accurately assess primary and secondary performance.
1. Chemical
2. Thermal
— Steam Flooding
— Fire Flooding
19
Figure 1.12: Carbon dioxide flooding process
3. Miscible
— Enriched Hydrocarbon Gas Flooding
— CO2 Flooding
— Nitrogen and Flue Gas Flooding
The complexity of these processes requires the gathering of large quantities of ad-
ditional laboratory fluid and core data and the use of considerably more complex
analysis techniques.
20
Figure 1.13: Chemical flooding process
Reservoir Engineers are required to answer the following three vital questions:
3. How will the production rates of wells depend on the physical pa-
rameters of the reservoir, reservoir geometry (shape), well num-
ber and development pattern and how will the rate decline with
time?
The first question may be answered if the shape and size of the pay zone is known
and the distribution of porosity and water saturation in the zone are also known.
21
This data is provided by the geologist and the petrophysicist. The reservoir
engineer may assist by estimating the positions of gas-oil and water-oil contacts
if the positions of these contacts is unknown.
The answer to the second question is very complex. It requires the use of sophisti-
cated mathematical models (usually computer based reservoir simulators). These
are required to model the many alternative developments which result in different
ultimate recoveries and profitability. The process of producing production fore-
casts for the different recovery mechanisms and development plans will always be
associated with some degree of uncertainty because geologic formations are highly
heterogeneous and the geological description, no matter how sophisticated, can
never capture all the geologic variability.
The answer to the third question relies on detailed analysis of pressure and indi-
vidual well test data.
22
Chapter 2
RESERVOIR DESCRIPTION
Reservoir Heterogeneity
Most reservoirs are layered because of variations that existed in the depositional
environment. Depositional conditions at any instant also vary from one location
to another which results in lateral as well as vertical changes within the reservoir
and within individual rock units. As we will see later, these changes result in
23
Figure 2.1: Highly detailes geostatistical models for reservoir characterization
24
variations in porosity, fluid distribution, and permeability. Permeability is a
measure of the relative ease with which fluids flow through the rock.
Wireline logs
Electric and other types of logs can be very important tools for determining
reservoir layering. Reservoir cross-sections based on logs can show if permeable
zones are continuous throughout the reservoir or if they are lenses having limited
areal extent.
Logs also show the net sand at each well. Net sand is the rock that contains recov-
erable hydrocarbons and possesses permeability. A geologist should be consulted
when analyzing logs for reservoir zonation and net sand thickness. Generally, logs
are available for all wells drilled and represent the most complete set of reservoir
descriptive data. Methods of analyzing logs and techniques of using logs for de-
termining net sand thickness and evaluating sand continuity are beyond the scope
of this course.
Core analysis
Core analysis data provide an additional basis for determining net sand thickness
and reservoir zonation. Core analysis data is more quantitative than logs in
describing the reservoir, but generally, only a fraction of the wells are cored.
However, in most cases logs are more effective when supported by core data. The
logs can be calibrated by core data to make them more useful from a quantitative
standpoint. Under some conditions, the calibrated logs can be used to obtain
fairly good estimates of the porosity and permeability profiles at all wells in a
reservoir.
Stratification
The two most important properties of net sand are porosity and permeability.
Porosity of net sand usually is in the range from 10 to 30 %. Some limestone and
dolomite reservoirs locally may have porosities as high as 60 %. The porosity
in reservoir rocks usually occurs in the spaces between rock particles and this is
called primary porosity or intergranular porosity. Primary porosity can also exist
in fractures and vugs. Primary porosity may be modified by post depositional
events. For example, small mineral particles may be deposited in the space be-
25
Figure 2.2: Vertical heterogeneity or layering
26
Figure 2.3: Examples of structural and geological complexity
27
Figure 2.4: Schematic of wireline logging operation
tween sand grains to produce microporosity. These digenetic changes may greatly
reduce the original porosity and permeability of a rock.
Typically, the permeabilities of the net sand portion of a reservoir will vary from
10 md or less to 500 md or more. The ability of a rock to allow fluid flow is
proportional to permeability, so fluid flow profiles in the reservoir may be very
uneven.
(iii) Interpretation of the above data for accuracy and reliability. These data
are used to evaluate initial volumes of oil and gas in the reservoir
28
Figure 2.5: Formation microscanner and resistivity logs
29
Figure 2.6: Schematic of a rotory core barrel
30
Figure 2.7: Diamond coring bits
Data collection is expensive (wireline logging, sampling, pressure testing etc.) and
the collection of poor quality or inaccurate data is contradictory and wasteful. It
is therefore necessary to place considerable effort into preparing an effective data
gathering program.
The primary objectives of a data gathering program are to answer the following
questions:
(i) Does the formation contain commercial quantities of oil and gas?
(ii) How should the reservoir be produces to maximize economic return?
(i) How much stock tank oil and/or free gas is initially in place?
(ii) What is the likely primary recovery mechanism and will it be necessary to
supplement this energy by water or gas injection?
(iii) What are the oil and gas reserves (production volumes for a particular field
development)?
(iv) How will individual well rates decline, and how can the decline in production
rate be arrested?
31
Figure 2.8: Schematic of a sidewall coring gun
32
Figure 2.9: Full diameter core
33
Figure 2.10: Length scales for laboratory core analysis
34
The above questions cannot all be answered immediately after drilling of a discov-
ery well. However, provided that the data gathering program is well thought-out,
the engineer can arrive at reasonable planning estimates.
As the field is developed and produced, additional data becomes available, and
this is integrated with the existing data to reduce the level of uncertainty associ-
ated with the initial estimates.
The overall data gathering program is thus a continuing process over the life of the
field. It is important to recognize this when developing the initial data gathering
program.
The following is a guide to the type of data which may be collected with the
drilling of the first well in a reservoir:
- Reservoir porosity.
35
Additional delineation or development wells drilled after the first discovery well
should provide the following data:
- Variations of sub-sea depth of reservoir top and base for structure maps.
These factors are determined in the same manner as for the first well. The
presence of multiple wells allows interference testing between wells to determine
average permeabilities between wells and to test the continuity of individual sand
units.
Not all of the above data will be collected from each well drilled. The engineer
must continually assess the data gathering process and only collect that data
which materially reduces the level of uncertainty in estimating the important
reservoir parameters.
When areal variations in rock properties are large, it may be necessary to collect
all the data from all the wells drilled and to drill additional data wells.
Coring is the most basic formation evaluation tool. It provides the engineer with
the only opportunity to physically inspect a piece of the reservoir. It provides
the only means of determining,
36
These are important in determining formation production characteristics and
reservoir recovery factors.
(i) lithology,
(ii) porosity,
of the formation penetrated by a well. Whereas only a few wells are fully cored,
it is common practice to log all wells in the field.
37
There are three basic types of log:
1. Electric — fundamental log run in all wells drilled. Most electric logs must
be run in an uncased hole containing conducting fluid.
Although logs provide valuable data for reservoir description, the main purpose
of logging is to identify a suitable completion interval for the well.
Production tests repeated on a yearly basis over the life of a well provide valuable
information on,
38
Figure 2.12: Wireline formation interval tester
Drill-stem tests are usually run at the time the well is drilled to determine if
the well should be completed over the interval identified by the well log. The DST
tool allows us to make a temporary completion to conduct pressure build-up and
draw-down tests. DST’s are useful for:
Reservoir oil usually contains a considerable amount of dissolved gas. When the
oil is produced to the surface the gas comes out of solution and the oil volume
consequently shrinks. The oil that fills a barrel at surface conditions will have
occupied between 10%—50% at reservoir conditions.
39
Figure 2.13: Initial and production formation pressure data with flowmeter survey
40
Figure 2.14: Single and multi-well pressure tests
41
To determine oil-in-place it is necessary to know the number of stock tank barrels
occupied by a reservoir barrel of oil.
Other important properties of oil, such as density and viscosity, also change when
solution gas is released. These properties are very important in reservoir fluid
flow calculations and must be accurately known.
In large reservoirs having high closure, fluid properties may vary significantly both
areally and vertically. Enough samples should be taken to adequately describe
these variations.
No single wireline tool or procedure is capable of providing all the data required
to characterize a reservoir and its contents. It is therefore necessary to develop an
integrated formation evaluation program which consists of a carefully considered
mix of:
(i) Logs - these provide most of the data for reservoir characterization.
(ii) Cores - used to calibrate logs for quantitative interpretation.
(iii) Well testing - provide estimates of permeability and productivity.
(iv) Fluid sampling - only means of determining reservoir fluid properties.
The best approach is to adopt a Key Well Program. The following steps are
taken in the development of such a program:
42
Figure 2.16: Bottom hole sampling tool
43
Figure 2.17: Surface sampling for laboratory recombination
2. A data gathering program is designed for each key well. This will include
logging, coring and well testing to provide complete reservoir coverage over
the reservoir.
4. Any available production data from key wells is also used to aide log inter-
pretation.
5. The above data gathering procedures are continuously monitored with the
objective of eliminating any unnecessary or ineffective procedures.
The above steps ensure a data gathering procedure which is both simple and cost
effective.
A reservoir description program is needed during all phases of the producing life
of a field.
44
Figure 2.18: Key well program
45
Figure 2.19: Aquifer models - limited data and interference
The aquifer is the total volume of porous water-bearing rock in pressure commu-
nication with a hydrocarbon reservoir. The size and permeability of an aquifer
will control how much water drive energy is available to the reservoir. The aquifer
46
energy will determine if the reservoir will produce primarily by water drive or by
liquid or gas expansion within the reservoir. Reservoir drive mechanisms will be
discussed in detail later in the course. At the present time, we are concerned only
with methods of determining the size and permeability of an aquifer.
If an aquifer is large, most of the information on it must come from wells drilled
outside the reservoir area. Logs and drill-stem tests on dry holes are about the
only source of aquifer data. Logs will show the thickness of water-bearing rock
that is in communication with the reservoir. If enough dry holes are available,
the areal extent of the aquifer can be estimated. An estimate of the aquifer
permeability can be determined from the results of drill-stem tests on dry holes.
Equations for calculating permeability from flow test data will be studies in the
portion of the course entitled fluid flow.
47
Chapter 3
The first step in a reservoir study is to accurately determine the initial hydro-
carbon volume. This requires data which will allow us to calculate the size and
geometry of the reservoir and the fluid volumes which the reservoir contains. In
this section we will briefly look at how maps and cross-sections are used to de-
scribe the geometry of a reservoir and calculate the hydrocarbon volume in-place.
Contour maps are commonly used to show reservoir geometry and the distribution
of important reservoir parameters.
Structure maps show the geometric shape of a reservoir or formation. The maps
may show the top or the bottom of a structure or reservoir unit. Examples of
top of structure maps are attached. These maps also show the positions of fluid
contacts in the reservoir.
Structure maps are prepared by geologists. The data on which the maps are
drawn usually come from;
Gross thickness isopach maps show the total interval between the top and
the base of the reservoir rock for each well. Structure maps on the top and on
48
Figure 3.1: Isometric schematic of the Ekofisk structure
49
Figure 3.2: Top-of-structure map of a hydrocarbon reservoir
the base of the reservoir can provide data for the isopach map. Frequently, most
of the wells are not drilled to the base of the reservoir so a base structure map
cannot be drawn. In this case, the gross sand interval must be estimated from
reservoir cross-sections based on logs from the well which penetrated the entire
interval.
The gross pay isopach map for an oil reservoir is more descriptive of the hydro-
carbon reservoir geometry than the gross thickness isopach.
Isopach maps show the distribution and thickness of reservoir properties of in-
terest. The contour lines connect points of equal vertical interval. Examples of
common isopach maps are:
Gross oil thickness isopach map: contours gross pay - the depth of the top
of the oil column minus the top of the bottom of the oil column.
Net oil thickness isopach map: contours net pay - gross pay minus non-
reservoir intervals such as shales.
Net oil isopach maps are commonly used to calculate volumes of hydrocarbons
in-place.
50
Figure 3.3: Net sand isopach map for a hydrocarbon reservoir
Net-to-gross ratio maps: fraction of the total hydrocarbon interval which con-
tributes to recovery.
Iso-porosity map: contours average porosity over net-pay portions of the de-
sired formation.
51
Figure 3.4: Isoporosity map for a hydrocarbon reservoir
52
3.3 VOLUMETRIC METHOD FOR DETER-
MINING ORIGINAL OIL-IN-PLACE
In this and the following reservoir engineering courses it is assumed that you are
familiar with units and unit conversions i.e., starting with the above equation for
any set of self consistent units, you should be able to calculate the constant 7758
in the preceeding equation. If you wish to review the topic of units go to the
section Units - unit conversions on page 108 of Dake, Fundamentals of reservoir
engineering.
53
Figure 3.6: Schematic of the microstructure of a sandstone showing sand grains
and interconnected pore space which allows fluid flow
The gross thickness is the difference in depth between the top and the
bottom of the reservoir zone.
54
3. Construct a net sand isopach map by eliminating all non-reservoir rock
intervals (shale, siltstone, coal seam etc.).
This procedure will normally involve estimates of minimum porosity and
permeability cut-offs. The actual intervals to be excluded are picked from
porosity logs which have been calibrated using core data.
55
The data gathering program should include water saturation data determined by
all of the above methods. Although cutting core with oil-based mud is expensive,
at least one well should be cored in this manner to provide data for calibration
of log resistivity.
The average oil formation volume factor is required to convert the reservoir oil or
gas filled hydrocarbon volume to the equivalent volumes at surface or stock tank
conditions.
Oil and gas formation volume factors are determined in laboratory PVT tests
conducted with representative samples of reservoir oil and gas.
Estimates of oil formation volume factors may be obtained from empirical corre-
lations if the following are known:
These are usually estimated from DST tests conducted on exploration wells.
56
Figure 3.7: Schematic of interstitual, irreducible or connate water in a waterwet
porous medium
57
Figure 3.8: Reservoir pressure survey map used to determine average reservoir
pressure
Calculate the initial volume of oil-in-place for the Apache Pool reservoir (top-of-
structure map attached). The average porosity, average connate water saturation
and average oil formation volume factor have been determined and these values
are given below.
Data:
φ = 0.27
S wi = 0.38
B oi = 1.2715 (RB/STB)
We use this exercise to introduce you to Mathcad. It is assumed that you have
installed Mathcad on your PC and that you have worked through the basics in
the on-line tutorial. In order to see the solution to this exercise you will need
to change some of the inputs to the spreadsheets. The areas of the spreadsheet
where these changes may need to be made are highlighted in yellow.
Solution outline
1. The first step is to determine the area inside each depth contour. The
contour areas must be determined from the map. This is usually done
58
Figure 3.9: Structure map for the Apache field
59
using specialized computer software and digitized maps. For this example
I have digitized each of the contours by hand and used Simpson’s rule to
numerically calculate the area. The use of Simpson’s rule for numerical
integration is shown in the attached figures. Study the three figures to be
sure that you understand what is being done.
To determine the area of a depth contour I first printed an enlarged copy
of the Apache structure map and overlayed this with a 1 cm by 1 cm grid.
I then divided each contour into an upper and lower curve as shown in the
attached figure and read-off the (x, y) points defining each curve. These
points are entered into a file for each contour eg., [C2000.prn] in the folder
[Contours]. If you open one of these files you will see the how the points
are entered for the lower and upper contours. Note that the end-points for
the lower and upper contours are the same. [Contour.mcd] , also located
in the [Contours] folder, reads the contour files and calculates the areas,
and plots the contour. This is done in the manner outlined in the course
notes and you should have no trouble following the flow of the calculation.
When Mathcad reads a file like [C2000.prn] all it ”sees” is a matrix of
(x, y) numbers - it ignors blanks or anything which it does nor recognise as
a numerical input. This makes it easy to annotate or ”pretty-up” the input
file so that it is understandable to the casual reader.
You can use as many data points as you like to define a contour - the more
points you use, the smoother the contour and the more accurate the area
calculation. The only limitation is that the total number of points defining
the lower and upper contours must be the same. This makes it a little easier
to program the calculations.
When you open [Contour.mcd] you will see that I have left it doing one
contour over and over. You will need to change the other input contour file
names to see the areas and plots for each of the contours.
The areas within each contour, A0 , A1 , A2 , etc. are multiplied by the map
scale-factor squared to convert the map areas to actual field values.
60
2. The bulk volume between two successive contours is given by the pyramidal
formula: µ ¶
h q
∆Vi = Ai + Ai+1 + Ai Ai+1
3
where,
∆Vi = bulk volume between contours i and i + 1.
Ai = the area enclosed by the lower contour.
Ai+1 = the area enclosed by the upper contour.
h = the vertical height between the contours, or
the contour interval.
3. The initial volume of oil-in-place in volume element ∆Vi ,in any consistent
set of units (as used by Mathcad), is given by,
∆Vi φi (1 − S wc,i )
∆Ni =
B oi,i
4. The initial oil-in-place is the sum of the values for each volume element.
X
N= ∆Vi
i
See the attached figures which show how Simpson’s rule is used to calculate
contour areas from digitized map data.
61
1. Contour is divided into upper and lower curves
Upper curve
Lower curve
Simpson's rule to calculate the area under the upper and lower curves
yi
yi+ 1
yi
yi+ 1
AU AL
∆x ∆x
X yi − yi+ 1
A= ∆x
2
62
Contour Area
AU
AC = AU − AL
AL
63
Problem 3.1 - Calculation of OGIP from a reservoir structure map
How much gas would the Apache Pool contain if the initial reservoir pressure was
1500 psia, the initial reservoir temperature was 200o F, and the gas compressibility
factor was 0.877 ? All other data as for Exercise 3.1.
Solution hint
You can use the areas, volumes etc., calculated in the previous exercise to help
you solve this problem by hand calculation or using your favourite spread-sheet.
If you do this be sure to be careful with units. If you want to master Mathcad
you can modify the files used in the previous example to do the calculation. If
you choose to do this make sure that you have looked at the Units section of the
on-line Mathcad tutorial before making the necessary changes.
Estimate the initial volume of gas-in-place for the Marlin Field (top-of-structure
map attached). The average reservoir and fluid properties are given below.
Data:
φ = 0.21
S wi = 0.19
T = 210o F
P = 2300 psia
z = 0.89
64
Figure 3.13: Marlin field top-of-structure map
Solution hint
You are free to solve this problem any way you want including using any com-
mercial or in-house software to which you may have access. If you have been
following the Mathcad route - I recommend this strongly - this problem will bring
you right up the learning curve.
Print a full-size (or larger) copy of the Marlin structure map. Create a full copy
of the folder for Example 3.1 and in order to modify the files to solbe the present
problem.
Follow the outline for Example 3.1 and construct the data files for contours (there
are 9 of these). Pay special attention to the particular manner in which these
files are constructed! Modify the [Contour.mcd] by copy-and-paste to calculate
the areas for all nine contours. Modify the final graph which plots the contours
to plot all nine contours. You will probably need to revise the ’graphs’ section of
the on-line manual to do this.
You will need to make the same changes to [Contour.mcd] made for Problem
3.1 to convert it to a gas in-place calculation. Note that for the Marlin contours
the contour depth intervals are not all the same size. The best way to handle
this is to read-in individual values of h in the same way as we already read-in
individual values of porosity, initial water saturation, areas etc. You can do this
65
by adding a column of numbers to the input data file and making the appropriate
changes in the spreadsheet. These changes will involve reading-in the new values,
introducing a new array for h, and modifying the equations to calculate with the
array elements hi . Describing these changes is a lot more difficult than making
them!
If you succede in making the above changes you will have learnt all you need to
know to reproduce any of the Mathcad spreadsheets in this and other courses.
66
3.4 DETERMINATION OF OIL-IN-PLACE —
MATERIAL BALANCE METHOD
Material balance methods are another way of determining the initial hydrocarbon
content of a reservoir. Material balance calculations:
67
3. Accurately measure and diligently report the production volumes
for all the fluids produced. Although produced oil volumes are accu-
rately measured as a matter of routine, material balance calculations require
equally accurate water and gas volumes.
Reserves for a particular field are estimated from an analysis of the available
engineering data. The implication of this is that the more reliable the data
(production history data), the more accurate will be the estimate of
reserves.
68
3.6 ESTIMATING DECLINE IN OIL PRO-
DUCTION RATES
The decline in field and individual well production rates is estimated on the basis
of:
3. Reservoir simulation.
For wells subject to severe water and/or gas coning reservoir simulation
offers the most reliable method for predicting well decline rates and overall
reservoir performance.
Reservoir engineering is studied in detail in course PTRL6004 - Reservoir
Simulation.
69
Chapter 4
HYDROSTATIC PRESSURE
DISTRIBUTION IN
RESERVOIRS
This section deals with the hydrostatic or initial pressure distribution in a reser-
voir - the pressure which exists prior to significant production from the reservoir.
We will consider the following specific topics:
3. Determination of oil water and gas densities and gradients from pressure
data.
70
Symbols and Units
g = 9.81 m/s2
1 Pascal (Pa) = 1 N/m2
1 bar = 105 N/m2
1 Atmosphere = 1.01325 bar or 14.695 psia
Conversion factors
All of the above units may be embedded into working Mathcad files and can be
used interchangeably or you can even mix units if you want. Normally we would
not elect to mix units!
The difference in hydrostatic pressure between any two depth points in a forma-
tion containing water is,
p2 − p1 = ρw g(D2 − D1 )
71
where, ρw is the average density of water over the interval (D2 − D1 ) and g is
the gravitational acceleration. ρw varies with depth (pressure) and salinity. Since
water is only slightly compressible, it is customary to neglect the overbar symbol
and simply write,
p2 − p1 = ρw g(D2 − D1 )
where it is understood that ρw is the average pressure over the interval of interest.
pwD − p0 = ρw gD
or,
pwD = p0 + ρw gD
The term ρw g(D2 − D1 ) is the hydrostatic pressure difference which has units of
pressure. If we divide this pressure difference by (D2 − D1 ), we obtain the water
gradient, γw , which is equal to ρw g and has units of pressure per unit depth. In
general we define a phase pressure gradient as
γi = ρi g
Using the definition of the fluid gradient, we can write that the pressure difference
between any two depths, ∆pi , is
∆pi = γi ∆D
∆pw = γw ∆D
The initial pressure, poD , at depth D in the oil zone may be expressed in terms of
the oil pressure at the initial OWC (a commonly used datum point for reservoir
engineering calculations) as,
72
Figure 4.1: Hydrostatic pressure distribution in a reservoir
or,
poD = poDOW C − γo (DOW C − D)
The initial pressure, pgD , at depth D in the gas cap may be expressed in terms
of the gas pressure at the initial GOC as,
or,
pgD = pgDGOC − ρg g(DGOC − D)
or,
pgD = pgDGOC − γg (DGOC − D)
73
4.2 HYDROSTATIC PRESSURE DISTRIBU-
TION IN A RESERVOIR CONTAINING
OIL, WATER AND GAS
In the absence of capillary pressure, the WOC and GOC are sharp and the fluid
pressures at the contacts are equal. The resulting hydrostatic pressure distribu-
tion in the reservoir is shown in the attached figure.
Note that the contacts correspond to the intersections of the fluid gradient lines.
This can be used estimate the positions of the contacts from measured pressure-
depth data.
74
Figure 4.2: Hydrostatic pressure distribution in a reservoir assuming negligible
capillary pressure
75
Example 4.1 - Calculation of regional hydrostatic pressures
[REGPRES.mcd]
Five widely separated exploration wells were drilled in a large sedimentary basin.
While penetrating the aquifer, the following pressure measurements were made
in each of the wells:
Well A B C D E
Rotary table elevation (ft above MSL) 2133 1312 2707 3937 197
Measured depth (ft) 9744 13993 8235 17388 9383
Gauge Pressure (psia) 4340 5656 2480 6005 4090
In answering this question you can use the Mathcad spreadsheet [REGPRES.mcd]
which reads the above data and calculates the required fluid gradients.
Solution hints
DT V D = DM D − DM SL
∆p
γw =
DT V D
76
Example 4.2 - Calculation of fluid contacts and fluid gradients from
pressure data [CONTACTS.mcd]
(ii) the density and the nature of the fluids present in the formation
Depth Pressure
(ft) (psia)
8120 2912
8202 2920
8284 2927
8366 2950
8448 2978
8530 3005
8612 3038
8694 3075
8776 3114
Solution hints
Plot the data on a depth-pressure plot. Identify lines of constant slope, these show
zones of different fluid saturation. Determine the gradients of depth-pressure lines
and from these calculate the fluid densities. The densities identify the fluids.
[Answer: DGOC = 8302 ft ss., DOW C = 8573 ft ss., ρg = 13.2 lb/cubic ft., ρo = 48.3
lb/cubic ft., ρw = 66.8 lb/cubic ft. ]
77
Figure 4.3: Hydrostatic pressure-depth data plot
78
Problem 4.1 - Optimal Location of an Exploration Well [EXPLOR.mcd]
A second exploration well EX-2 encountered the same sand between 7780 ft-ss
and 7980 ft-ss but found it to be only water-bearing. Mechanical problems with
the downhole gauge prevented a pressure measurement from being taken. The
two wells are 12,000 ft apart.
On the basis of previous experience and sampling of reservoir fluids we have deter-
mined that the regional water gradient is 0.524 psi/ft. The formation is normally
pressured. The pressure gradient for the gas phase at reservoir conditions is cal-
culated to be 0.084 psi/ft. The oil gradient, at reservoir conditions, is estimated
to be 0.296 psi/ft.
Questions
(i) Is the above data consistent with the assumption that the formation could
be oil-bearing between 6660 and 7880 ft-ss ?
(ii) Where would you locate an additional exploration well which would defi-
nitely find oil if any oil is indeed present?
(iii) What is the maximum possible thickness of the oil zone?
[Answers: (i) yes, (ii) new well should intersect the sand at a depth of 7445 ft ss.,
(iii) 910 ft.]
Solution hints
Each of the wells gives us a fluid and a corresponding fluid pressure. Where a
mechanical problem prevented the measurement of a water phase pressure, we
can estimate the pressure by assuming that the formation is normally pressured
(i.e., water gradient times depth).
The first well gives us the depth of lowest known gas. The second well gives the
depth of highest known water. If an oil zone exists, it must be between these
depths.
Knowing the gas and water gradients, and a fluid pressure and corresponding
depth in the gas and water zones, we can draw the gas and water gradient lines
79
Figure 4.4: Maximum thickness of an oil zone between gas and water contacts
on a pressure-depth plot.
If there is no oil present (only gas and water), the depth of the GWC can be
found from the intersection of the gas and water gradient lines. If a drop of oil
is present it must gravitate to this depth splitting the GWC into a WOC and a
GOC. The third well must intersect this depth to prove if any oil is present in
the reservoir.
The maximum possible thickness of the oil zone occurs when either the lowest
known gas or the highest known water corresponds to an oil contact. How do we
select which of the two is a possible contact? Simple, draw the oil gradient line
through each of the points and select the one which produces a set of contacts
(OWC and GOC) which are consistent with lowest known gas and highest known
water.
If you understand the principles involved and the steps required to solve the prob-
lem you should have little problem in entering the correct data into [EXPLOR.mcd]
and manipulating the graph by setting appropriate contact and oil gradient lines
to produce the correct answer.
80
Problem 4.2 - Calculation of a Pressure Kick when Penetrating a Hy-
drocarbon Zone [PKICK.mcd]
Calculate the pressure kick to be expected when a well first penetrates a reservoir
at 5000 ft subsea if the reservoir is known to have an OWC at 5500 ft and an
GOC at 5200 ft.
The formation is known to be normally pressured with the following phase gra-
dients;
water gradient 0.45 psi/ft
oil gradient 0.35 psi/ft
gas gradient 0.08 psi/ft
What would the pressure kick be if the entire hydrocarbon zone contained gas?
Solution hints
When drilling through the cap rock which forms the reservoir seal, the drill bit
experiences a water hydrostatic pressure gradient because the seal is saturated
with water and in a normally pressured system this water is in hydraulic com-
munication with the aquifer. Just before the bit penetrates the reservoir the bit
pressure is the of the water gradient and depth.
You do not really need a spreadsheet to solve this problem. If you know what you
are doing you can solve the problem faster with a hand calculator! I have prepared
the spreadsheet [PKICK.mcd] as an example of how a simple calculation can be
layed out in Mathcad. Enter the correct numbers and you will get the solution.
81
Figure 4.5: Calculation of a pressure kick
Two wells were drilled in a remote region. Well-A was drilled down-dip of the
structure and encountered only the aquifer. The operator had the foresight to
measure water pressures over a 160 foot interval to determine the water pressure
regime in this new area. The second Well-B, was drilled up-structure several
kilometers from Well-A and discovered a 50 foot oil column with good porosity
and permeability. Six RFT pressures were measured over this interval.
82
The pressures recorded for the two wells are summarized below. Note that in
order to meaningfully compare the pressures in the wells it is necessary to convert
measured depths to a common datum (depth sub-sea) and to express pressures
in absolute units (psia).
Well-A Well-B
Depth (ft.ss) Pressure (psia) Depth (ft.ss) Pressure (psia)
6075 2662 5771 2602
6091 2669 5778 2604
6108 2677 5790 2608
6220 2725 5800 2610
6232 2731 5806 2612
5816 2615
What conclusions can you draw from this data with regard to the fluids, the
reservoir and the aquifer?
Solution hints
83
Figure 4.6: Lithostatic gradient
Tf = Ts + GT Df
84
Figure 4.7: Geothermal gradient
85
Chapter 5
FLUID PROPERTIES
The volume of solution gas released and the associated changes in oil properties
have a significant influence on the production characteristics of the reservoir. The
attached figure shows a schematic of solution gas release in an oil reservoir.
- Oil shrinkage.
These properties are determined in special laboratory tests which require rep-
resentative reservoir fluid samples. The properties are called PVT (pressure-
volume-temperature) properties of the reservoir fluids. Before considering the
specific PVT parameters of interest to reservoir engineering it is necessary to
review some general but basic concepts in hydrocarbon phase behavior.
86
Figure 5.1: Oil reservoir above and below the bubble point
All substances can exist as gases, liquids or solids. Whether a particular substance
exists as a gas, a liquid or a solid (or a mixture of liquid and gas or a mixture of
all three) depends on:
- Pressure.
- Temperature.
- Composition
For a pure hydrocarbon such as ethane, propane, butane, methane etc., temper-
ature and pressure fully define the state of the hydrocarbon. The state of a pure
substance can be represented on a P-T phase diagram.
The P-T phase diagram can be constructed by experimentally observing the be-
havior of the pure substance in a windowed high pressure test cell as shown in
the attached figure.
Over the pressure and temperature range shown in the attached figure, the vapor
pressure curve, which terminates in a critical point (C), divides the P-T space
into liquid and gas regions.
To the right of the critical point lies a single phase super critical region. A gas
at a temperature above it’s critical temperature, may be compressed indefinitely
without passing through a phase transition.
87
Figure 5.2: Surface production system for a gas reservoir
88
To the left of the critical point the fluid is;
- mixture of liquid and vapor for points on the vapor pressure curve.
- For a liquid state at high pressure, reducing the pressure at constant tem-
perature can result in a phase change from liquid to vapor when the pressure
falls to the vapor pressure. Point F represents a liquid state at high pressure.
If the pressure is reduced to the fluid vapour pressure (the intersection of
the line AF and the vapour pressure curve) both liquid and vapour phases
can coexist. When the pressure falls below the vapour pressure to point A,
the fluid is in a single vapour state.
The behavior of hydrocarbon mixtures is more complex than that of a pure fluid.
For purposes of illustration we consider a two component mixture. The behavior
of more complex mixtures is similar.
The attached figure shows the P -T phase diagram for a 50:50 mixture of propane
and heptane. Also plotted are the pure component vapor pressure curves.
The major differences between the P -T phase diagrams for a single component
and a two-component mixture are:
89
Figure 5.4: Pressure-temperature diagram for ethane
90
Figure 5.5: Pressure-temperature diagram for ethane-heptane mixtures
1. For the mixture there now exists a two-phase region or a range of pressures
over which two phases can coexist at constant temperature.
2. The two-phase region is bound by a bubble point line and a dew point line
which meet at the mixture critical point.
The bubble point pressure is the pressure at which the first bubble of gas
appears as the pressure of a liquid is reduced at constant temperature.
The dew point pressure is the pressure at which the first drop of liquid
appears as the pressure of a gas is increased at constant temperature.
3. Within the two-phase region are lines of constant liquid (or gas) content.
4. The critical point is the temperature and pressure at which the properties
of the liquid and vapor phases are identical.
We note that for mixtures, liquid and gas phases mixtures may exist at
conditions above the critical point.
5. The size and shape of the two-phase region and the location of the critical
point vary with mixture composition.
91
Figure 5.6: Pressure-temperature diagram for a multi-component mixture
Oil Reservoir
The phase diagram for a typical oil reservoir having a temperature T is shown in
the attached figure.
The initial condition of the reservoir (temperature and pressure) is at point A’.
With production the reservoir pressure will fall at constant temperature T along
the line A’ABC.
As the pressure continues to fall below the bubble point pressure along the line
ABC, free gas appears in the reservoir as a result of solution gas release.
As the pressure continues to fall in the two-phase region, the percentage liquid
volume decreases.
92
Figure 5.7: Pressure-temperature diagram for a reservoir oil
For an oil reservoir T , the reservoir temperature, lies to the left of the critical
point.
The phase diagram for a typical retrograde condensate gas reservoir having a
temperature T is shown in the attached figure.
When pressure falls this reservoir enters the two-phase region through a dew
point producing a condensate phase in the reservoir. This behavior is termed
retrograde.
For a retrograde condensate gas reservoir T , the reservoir temperature, lies to the
right of the critical point.
93
Figure 5.8: Pressure-temperature diagram for a gas condensate reservoir
94
Gas Reservoir
The phase diagram for a typical gas reservoir having a temperature T is shown
in the attached figures.
When pressure falls these reservoirs do not enter the two-phase region.
The reservoirs may be further classified as wet gas if the separator condition falls
in the two-phase region, and dry gas if the separator condition is single-phase.
The following definitions refer to the PVT properties used in reservoir engineering
to characterize oil and gas reservoirs.
Parameter Symbol Definition
95
Figure 5.10: Production of an oil reservoir above and below the bubble point
The above properties are used to relate surface volumes (mass) to reservoir vol-
umes.
Oil and gas production rates, Qo (STB/D)and Qg (SCF/D), are measured at the
surface at a time when the reservoir pressure is P . This pressure is below the
bubble point pressure Pb . What are the corresponding underground withdrawal
rates in (RB/D)?
Since every STB of oil produced to the surface produces Rs SCF of solution gas,
the volume of free gas produced from the reservoir is
(R − RS ) (SCF/STB)
96
Figure 5.11: Use of PVT properties to relate surface measured production rates
to reservoir withdrawal volumes
Each STB of oil produced to the surface requires the withdrawal of Bo RB of oil
and is accompanied by (R − Rs )Bg RB of free gas.
The oil production rate is 2500 STB/D and the gas production rate is 2.125
MMSCF/D. If the reservoir pressure at this time is 2400 psia, what are the
underground withdrawal rates?
If the density of stock-tank oil is 52.8 lb/ft3 and the gas gravity is 0.67 (density
of air at standard conditions is 0.0763 lb/ft3 ) calculate the oil density and gas
density at reservoir conditions when the reservoir pressure is 2400 psia.
97
[Answer: qo = 2956 RB/day, qg = 1482 RB/day, ρo =47.4 lb/cubic ft., ρg =7.65
lb/cubic ft.]
Solution hint
To calculate reservoir fluid densities use 1 STB oil and 1 SCF gas as a basis.
This gives Bo and Bg as the reservoir volumes of oil and gas, respectively. Use
the PVT properties and the surface densities to calculate the corresponding fluid
masses at reservoir conditions.
Enter the correct numbers into the spreadsheet [SUBSURV.mcd] and see the solu-
tion. Study the spreadsheet carefully in order to fully understand the calculation
of densities at reservoir conditions.
Typical relationships between PVT properties and pressure are shown schemati-
cally in the attached figure.
Solution GOR
The volume of dissolved gas decreases from Rsi , the initial solution GOR at the
bubble point (Pb ), to zero at atmospheric pressure.
98
Figure 5.12: Dependence of oil PVT properties on reservoir pressure
99
For pressures greater than Pb , Bo decreases due to compression as pressure in-
creases.
P = pressure, psia
V = volume, ft3
z = gas deviation factor, dimensionless
n = number of moles, lb mole
R = gas constant, 10.73 psia ft3 /o R lb mole
T = temperature, o R (o R =o F + 460)
Taking one mole of gas at standard conditions (14.65 psia and 60 o F) and com-
pressing it to reservoir conditions (PR psia and TR o R) gives,
14.65V1 = z1 nR(60 + 460)
PR VR = zR nR(TR )
Dividing the above equations we obtain,
VR 14.65 zR TR
=
V1 520 z1 PR
Since Bg has the units RB/SCF (1 bbl = 5.615 ft3 ) and z1 = 1.0,
VR 14.65 zR TR
Bg = =
5.615 5.615 × 520 1 PR
zR T R
Bg = 5.02 × 10−3
PR
The compressibility factor, zR , for natural gas may be estimated from the attached
figure where the compressibility factor is plotted as a function of pseudo-reduced
temperature (Tpr ) and pseudo-reduced pressure (Ppr ).
T
Tpr =
Tpc
100
P
Ppr =
Ppc
where Tpc and Ppc are the gas pseudo-critical temperature and pseudo-critical
pressure respectively.
The pseudo-critical properties of a gas are a function of gas gravity and may be
estimated from the attached figure.
Gas gravity
Gas gravity is the ratio of the density of a gas to the density of air at standard
conditions.
At standard conditions gases obey the ideal gas law and gas density may be
expressed as;
P V = nRT
The number of moles n, may be expressed in terms of the mass of gas m, and the
molecular weight of the gas M ,
m
n=
M
Combining the equations gives,
m
PV = RT
M
or,
m P Mg
ρg = =
V RT
Similarly, the density of air is,
m P Mair
ρair = =
V RT
The gas gravity, γg is thus simply,
ρg Mg
γg = =
ρair 29
The molecular weight of the gas is determined from a laboratory analysis of a gas
sample.
101
Figure 5.13: Pseudo-critical properties for natural gas and gas condensates
102
5.3 CALCULATION OF GAS PROPERTIES
For a single gas component, the reduced temperature, Tr , and reduced pressure,
Pr , are defined as follows:
T
Tr =
Tc
P
Pr =
Pc
where,
T = temperature of interest, o R
Tc = critical temperature of the gas, o R
P = pressure of interest, psia
Pc = critical pressure of the gas, psia
Tc and Pc are constants for a single gas component and may be obtained from
standard tables of the properties of pure gas components.
Once Tr and Pr are known, the compressibility factor, z, may be read from
compressibility charts and Bg in units of RB/SCF is calculated from:
zT
Bg = 5.02 × 10−3
P
where T is in o R and P is in psia.
103
CRITICAL PROPERTIES OF GASES
Component Molecular Tc Pc
o
Weight R psia
104
5.3.2 Multi-Component Gas Mixtures
The pseudo reduced temperature, Tpr , and pseudo reduced pressure, Ppr , are
defined as follows:
T
Tpr =
Tpc
P
Ppr =
Ppc
Once Tpr and Ppr are known, the compressibility factor, z, may be read from
compressibility charts and Bg calculated from:
zT
Bg = 5.02 × 10−3
P
where T is in o R and P is in psia.
If the gas gravity is known, the chart may be used to estimate the gas pseudo
critical properties.
105
Example Calculation — Bg
Calculate the gas formation volume and gas density at reservoir conditions of
225o F and 2500 psia. The gas composition is:
Methane 0.80
Ethane 0.15
Propane 0.05
Solution
Component Mole Fraction Tc (o R) Tc (o F ) Pc (psia) yTc yPc
o
R =o F + 460
1.
Tpc = 391o R Ppc = 676psia
2.
T 460 + 225
Tpr = = = 1.75
Tpc 391
P 2500
Ppr = = = 3.70
Ppc 676
3. From the generalized compressibility chart, read
z = 0.87
4.
zT (0.87)(225 + 460)
Bg = 5.02×10−3 = 5.02×10−3 = 1.2×10−3 RB/SCF
P 2500
106
Example Calculation - Mg , γg and ρg
Calculate the gas molecular weight, gas gravity and the gas density at reservoir
conditions of 225o F and 2500 psia. The gas composition is:
Methane 0.80
Ethane 0.15
Propane 0.05
Solution
1.
3
X
Mg = yi Mi = 19.54
1
2.
Mg 19.54
γg = = = 0.675
29 29
3.
P Mg 2500 × 19.54
ρg = = = 7.64 lb/f t3
zRT 0.87 × 10.73 × (460 + 225)
107
Calculation of Gas Properties
Calculate γg , Bg and ρg at reservoir conditions of 150o F and 1500 psia. The gas
composition is:
Methane 0.70
Ethane 0.12
Propane 0.10
n-Butane 0.08
Solution
Component Mole Fraction Tc (o R) Tc (o F ) Pc (psia) yTc yPc
o
R =o F + 460
1.
2.
T 460 + 150
Tpr = = = 1.406
Tpc 434
P 1500
Ppr = = = 2.266
Ppc 662
z = 0.75
108
4.
zT (0.75)(150 + 460)
Bg = 5.02×10−3 = 5.02×10−3 = 1.53×10−3 RB/SCF
P 1500
6.
Mg 23.8
γg = = = 0.82
29 29
7.
P Mg 1500 × 23.8
ρg = = = 7.29 lb/f t3
zRT 0.75 × 10.73 × (460 + 150)
109
Figure 5.14: Schematic of a laboratory PVT test cell
Laboratory tests to measure PVT parameters are carried using samples of reser-
voir oil at a constant reservoir temperature.
The laboratory tests are conducted in high pressure windowed cells. These cells
allow accurate visual measurement of oil and gas volumes in the cell at different
pressures.
The pressure in the cell is lowered by increasing the cell volume. This is achieved
by removing accurately measured volumes of mercury from the cell using a cal-
ibrated high precision piston pump. The attached figure shows the essential
features of the PVT test apparatus.
Three specific tests are performed to characterize an oil and it’s associated gas:
110
Figure 5.15: Windowed PVT test cell
111
Figure 5.16: PVT laboratory at UNSW
112
5.4.1 Flash Expansion Test
A reservoir oil sample is introduced into the cell and mercury is injected to raise
the cell pressure above the initial reservoir pressure, pi .
The cell pressure is lowered in small steps by removing a small volume of mercury
at each step. The total hydrocarbon volume, vt , in the cell is measured at each
step.
All cell volumes are reported relative to the volume in the cell at the bubble point
pressure, pb .
The following table shows a set of typical laboratory data for this test.
5000 0.9810
4500 0.9850
4000 pi 0.9925
3500 0.9975
3330 pb 1.0000
3290 1.0025
3000 1.027
2700 1.0603
2400 1.1060
2100 1.1680
This data is used to determine the bubble point pressure, pb , by noting that the
total compressibility of the cell increases dramatically when gas is released from
solution.
The pressure in the cell is reduced in small steps by removing mercury from the
cell.
113
Figure 5.17: Schematic representation of flash and differential liberation tests
114
At each step the cell oil volume, vo , and gas volume, vg , are measured.
The gas in the cell is then slowly displaced from the cell with mercury at constant
pressure. The displaced gas volume is measured at standard conditions and the
volume, Vg , is noted.
The above procedure is repeated for small steps down to atmospheric pressure.
Typical data produced from a differential liberation test is shown in the table
below:
Pressure Relative Gas Vol. Relative Gas Vol. Relative Oil Vol.
(psia) at p and T , vg at sc, Vg at p and T , vo
4000 0.9925
3500 0.9975
3330 pb 1.0000
3000 0.0460 8.5221 0.9769
2700 0.0417 6.9731 0.9609
2400 0.0466 6.9457 0.9449
2100 0.0535 6.9457 0.9298
1800 0.0597 6.5859 0.9152
1500 0.0687 6.2333 0.9022
1200 0.0923 6.5895 0.8884
900 0.1220 6.4114 0.8744
600 0.1818 6.2369 0.8603
300 0.3728 6.2297 0.8459
14.7 200o F 0.8296
14.7 60o F 0.7794
In addition to the above data, the laboratory also reports the Cumulative Relative
Gas Volumes collected at atmospheric pressure and reservoir temperature and at
STC:
115
Figure 5.18: Laboratory test separator
The PVT cell is brought to the bubble point pressure and connected to the
separator system which may be a single separator or a series of staged separators
with staged pressures and temperatures to simulate the actual production system.
The cell contents are then flashed through the separator system to standard
conditions. The resulting volumes of produced oil and gas are measured.
The data from such tests is used to determine the oil shrinkage factor, cbf , and
the initial solution GOR, Rsif .
116
5.4.4 Procedure for calculating PVT parameters from
laboratory data
The above data can be used to compute the PVT properties for the tested oil
and gas. The procedure involves the following steps:
1. Plot the flash expansion data, p vs vt , to determine the bubble point pres-
sure.
3. Use the differential flash data to compute the cumulative relative gas vol-
ume, F , liberated from the cell at every pressure step;
pb
X
Fp = Vg
p
4. Use the differential flash data and the oil shrinkage factor, cbf , to compute
Bo , " #
∙ ¸
RB vo RB/RBb
Bo = =
STB cbf STB/RBb
5. Use the differential flash data, the oil shrinkage factor, cbf and the cumu-
lative gas liberated, F , to compute Rs ,
117
Example 5.2 - Calculation of PVT properties from laboratory PVT
data [PVT.mcd]
Using the Flash expansion, differential liberation and separator flash expansion
data discussed in the previous sections, determine the following as a function
pressure at reservoir temperature:
6. Gas compressibility
Determine the above properties for the optimum surface operating condition.
118
5.5 FLUID SAMPLING
Fluid samples for PVT analysis are collected early in the life of a reservoir. The
reservoir is usually sampled in one of two ways;
1. sub-surface sampling
2. surface sampling.
If the reservoir is saturated (initial reservoir pressure is equal to the bubble point
pressure), the pressure in the vicinity of the wellbore will be below the bubble
point pressure and gas will come out of solution as the oil flows to the wellbore.
Under these conditions the oil sample may not be representative.
If the sample is to be representative, the oil flowing into the wellbore must have
the same solution GOR as the reservoir oil away from the well. When gas is
first released in a reservoir, the gas remains immobile until the gas saturation
increases to a value called the critical gas saturation. During the period that the
gas saturation is below the critical value, oil flowing into the wellbore will be
deficient in gas. On the other hand, when sufficient gas has been released for gas
to become mobile, the very high mobility (low viscosity) of the gas will result in
a disproportion ally high volume of gas entering the wellbore.
The liquid volume is usually very small compared to the total volume of the sys-
tem and in order to measure it accurately it is necessary to use special condensate
PVT cells. These cells are designed to allow light to pass through the liquid and
119
Figure 5.19: Constant mass expansion test for a gas condensate
are fitted with front and back windows for this purpose. Some condensate cells
are made out of a solid block of sapphire to allow un obstructed viewing of the
liquid phase.
The most common type of test used to characterize a gas condensate is the
constant mass depletion test. Since the liquid volume produced in the reservoir
is small, it is immobile and remains in contact with the gas from which it was
produced. The constant volume depletion test simulates this behavior.
In the case of very rich condensates where the volume of liquid produced is
relatively large, the liquid phase in the reservoir may become mobile. The liquid
will move to the bottom of the reservoir under the action of gravity and a constant
volume depletion test is more appropriate.
Typical liquid dropout curves for constant mass and constant volume depletion
tests are shown in the attached figure. The richer the gas condensate, the more
liquid is produced and the greater the difference between the liquid dropout
curves.
120
Figure 5.20: Constant volume expansion test for a gas condensate
Gas hydrates are solid, semi-stable compounds which sometimes plug natural gas
flowlines, processing and measuring equipment, and pipelines. Hydrates consist
of geometric lattices of water molecules containing cavities filled with gas - a
solid foam. Gas hydrates form when hydrocarbon gases come into contact with
water at temperatures below 35o C. A typical phase diagram for a hydrate forming
gas-water system is shown in the attached figure.
121
Figure 5.21: Liquid drop-out curves for a gas condensate
Gas Hydrates
Solid, semi-stable compounds which sometimes plug natural
gas flowlines, processing equipment and pipelines
122
Figure 5.23: Gas hydrate co-existence curves. H-hydrate, G-gas, L1-water, L2-
liquid hydrocarbon, I-ice
Figure 5.24: Comparison between measured and calculated hydrate curves for a
gas with MEOH inhibitor
123
Figure 5.25: Effect of different inhibitors on hydrate formation
where,
The surface tension between two fluids is a function of pressure, temperature and
composition of the phases. The surface tension of hydrocarbon mixtures may be
124
Figure 5.26: Pendant drop tensiometer
125
estimated using the parachor method. For a pure liquid in equilibrium with it’s
vapor,
ρL − ρV
σ 1/4 = Pch
M
where,
Pch = parachor
ρL , ρV = phase densities, gm/cm3
σ = surface tension, dynes/cm
M = molecular weight
Parachors account for intermolecular forces and are predicted from the structures
of molecules. A correlation for the parachor with molecular weight is given in the
attached figure. For mixtures the surface tension is given by,
X µ ¶
ρL ρV
σ 1/4 = Pchi xi − yi
ML MV
where,
Several useful correlations exist for estimating reservoir fluid properties in the
absence of laboratory data.
Many of the available graphical correlations of fluid properties have been com-
puterized which makes their use particularly easy. An example of such a program
is given in the file PropEst.mcd.
126
Figure 5.27: Surface tensions for hydrocarbons at atmospheric pressure
The following estimates are made of reservoir and produced fluid properties from
a DST on an exploration well. What are the reservoir properties of the oil, water
and gas?
o
TR = 200 F
PR = 3330 psia
PS = 115 psi
o
TS = 60 F
o
AP I = 30 API
GOR = 510 SCF/STB
γg = 0.75 (air= 1)
C = 100 (water salinity in units of kg/m3 )
N aCl = 6 (water salinity in units of 10,000 ppm)
[Answer: open the spread-sheet, enter the appropriate input values and see]
127
Figure 5.28: Parachors for hydrocarbons
128
Figure 5.29: Standing correlation for reservoir oils
129
Figure 5.31: Viscosity of reservoir brine
130
Figure 5.32: Viscosity of hydrocarbon gases at atmospheric pressure
131
Problem 5.1 - Calculation of PVT properties from laboratory PVT
data
A laboratory PVT cell contained 280.0 cm3 of reservoir liquid at its bubble point
of 2000 psia at 140o F. A volume of 18.8 cm3 of mercury was withdrawn from the
cell and the pressure fell to 1600 psia. Mercury was then reinjected at constant
temperature and pressure to displace the gas from the cell. This left 263.5 cm3
of liquid in the cell and resulted in the collection of 0.129 SCF of gas.
The process was repeated, reducing the pressure to 14.7 psia and the temperature
to 60o F. Then 0.388 SCF of gas were removed from the cell and 205.9 cm3 of liquid
remained in the cell.
solution hints
If you can do this without using the PVT.mcd spread-sheet you have a good
understanding of PVT properties.
132
Chapter 6
MATERIAL BALANCE
EQUATIONS
There is therefore a relationship between the rate of production and the rate of
decline of reservoir pressure. Material balance equations express this dependence
in mathematical form.
The diagrams in this section are best viewed on the electronic version of the
course notes. You may wish to make colour prints of these figures.
133
GAS CAP
OIL ZONE
AQUIFER
Most material balance equations are written in terms of the original volume oc-
cupied by the oil.
The volume originally occupied by produced oil may now be occupied by;
134
Figure 6.2: Material balance on the pore space occupied by the original oil volume
If a gas cap is present, and the reservoir pressure drops, the gas cap will expand
to replace some of the volume initially occupied by the produced oil.
where,
G = original gas cap gas volume, [SCF]
Gpc = cumulative gas production from the gas cap, [SCF]
Bg = gas formation volume factor at current pressure, [RB/SCF]
Bgi = gas formation volume factor at original reservoir pressure, [RB/SCF]
Note that if Gpc is large, the gas cap may actually shrink rather than expand.Gas
cap shrinkage should never be allowed because it always results in a loss of oil
recovery.
135
Figure 6.3: Gas cap expansion volume
Calculate the change in the size of the gas cap after 20% of the gas cap gas has
been produced while the reservoir pressure had dropped from 1225 psig to 1100
psig. The gas cap originally contained 21.3 × 109 SCF.
Data:
G = 21.3 ×109 [SCF]
Bgc at 1225 psig = 0.002125 [RB/SCF]
Bgc at 1100 psig = 0.002370 [RB/SCF]
Solution
1. At 1100 psig the gas cap containing 0.8 times the original gas cap volume
i.e., G = 0.8Gi
2.
∆VGCE = (G − Gpc )Bg − GBgi
∆VGCE = (0.8 × 21.3 × 109 − 0) 0.002370 − 21.3 × 109 × 0.002125
∆VGCE = −4.88 × 106 RB
i.e., the gas cap has actually shrunk. This would allow about 5 MMRB oil
to migrate into the gas cap, a zone originally free of oil. This would result
in a loss of about 1MMRB of oil.
We would not allow this to actually happen in the actual reservoir.
136
Example 6.2 - Calculation of gas cap expansion [MBE.mcd]
Calculate the change in gas cap size for the reservoir of Example-1 if the reservoir
pressure had dropped from 1225 psig to 900 psig at the time that 20% of the gas
was produced.
Data:
G = 21.3 ×109 [SCF]
Bgc at 1225 psig = 0.002125 [RB/SCF]
Bgc at 900 psig = 0.002905 [RB/SCF]
Solution
i.e., the gas cap has expanded into the oil zone and no oil is lost to the gas
zone.
137
Figure 6.4: Released solution gas volume
If the reservoir pressure falls below the bubble point pressure gas will be released
from solution.
At any time during the production of a reservoir, the gas originally in solution
can be placed into three categories;
where,
N = original oil volume, [STB]
Np = cumulative oil produced, [STB]
Rsi = original solution gas-oil ratio, [SCF/STB]
Rs = solution gas-oil ratio at current pressure, [SCF/STB]
Bg = gas formation volume factor at current pressure, [RB/SCF]
138
Example 6.3 - Calculation of released solution gas volume [MBE.mcd]
Cumulative oil production for our example reservoir was 14.73 ×106 STB at
the time when reservoir pressure was 900 psig. At the same time cumulative
production of solution gas was 4.05 ×109 SCF. Calculate the reservoir volume
occupied by released gas.
Data:
N = 90.46 ×106 [STB]
Rsi at 1225 psig = 230 [SCF/STB]
Rs at 900 psig = 169 [SCF/STB]
Bg at 900 psig = 0.002905 [RB/SCF]
Solution
139
Figure 6.5: Remaining oil volume
Reservoir
| oil volume} = (N − Np )Bo
{z | {z }
[RB] oil still in reservoir
where,
N = original oil volume, [STB]
Np = cumulative oil produced, [STB]
Bo = oil formation volume factor at current pressure, [RB/STB]
∆VROV = (N − Np )Bo
140
Example 6.4 - Calculation of remaining oil volume [MBE.mcd]
What is the remaining reservoir oil volume for the previous example at 900 psig.
Data:
Solution
∆VROV = (N − Np )Bo
141
Figure 6.6: Rock and connate water expansion volume
The expansion of rock and connate water are combined into one term and ex-
pressed as the formation compressibility cf .
cf is defined as the fractional change in pore volume per psi change in reservoir
pressure.
The pore volume can be expressed in terms of the original oil volume, as is
required for material balance calculations.
where,
N = original oil volume, [STB]
Boi = oil formation volume factor at initial pressure, [RB/STB]
Vp = reservoir pore volume, [RB]
Soi = initial oil saturation
Swi = initial or connate water saturation
or, µ ¶
N Boi
Vp =
1 − Swi
142
The total amount of rock expansion is calculated by utilizing the definition of
compressibility;
1 ∆V
c=
V ∆P
from which we have
∆V = cV ∆P
Rock expansion = formation compressibility × pore volume × pressure change
| {z }
[RB]
µ ¶
N Boi
Rock expansion = cf (pi − p)
| {z } 1 − Swi
[RB]
where,
cf = formation compressibility, [vol/vol/psi]
p1 = initial reservoir pressure, [psig]
p = current reservoir pressure, [psig]
The total amount of connate water expansion is given by,
Water expansion = water compressibility × water volume × pressure change
| {z }
[RB]
Combining the above equations, we have for rock and water expansion,
µ ¶
N Boi
∆VRW E = (cf + cw Swi ) (pi − p)
1 − Swi
For reservoirs where a gas phase is present, the rock and water expansion term is
so small that it may safely be neglected.
The rock and connate water term is usually only important for oil reservoirs when
the oil pressure remains above the bubble point.
143
Example 6.5 - Calculation of rock and connate water expansion volume
MBE.mcd]
What is the rock and water expansion volume for the previous example when the
pressure falls from 1225 psig to 900 psig.
Data:
Swi = 0.205
cf = 3.0×10−6 [psi−1 ]
cw = 3.0×10−6 [psi−1 ]
Solution
µ ¶
N Boi
∆VRW E = (cf + cw Swi ) (pi − p)
1 − Swi
∆VRW E = (cf + cw Swi ) (Vp ) (pi − p)
³ ´
∆VRW E = (3.0 + 3.0(0.205)) 10−6 127.84(106 ) (1225 − 900)
∆VRW E = 0.15 × 106 RB
We see that rock and water expansion amounts to about 1% of the released gas
volume. This is usually the case in practice and rock and connate water expansion
can be neglected for calculations below the bubble point.
144
Figure 6.7: Water influx volume
Unlike the above items in the material balance equation, the volume of water
influx cannot be calculated directly.
However, since we can calculate all the other terms in the material balance equa-
tion, we can determine the net water influx into the reservoir — total water
entering the reservoir less water produced — by difference.
|Net water
{z influx} = W e
|{z}
− Wp Bw
| {z }
[RB] cumulative water influx cumulative produced water
where,
We = cumulative water influx, [RB]
Wp = cumulative water produced, [STB]
Bw = water formation volume factor at current pressure, [RB/STB]
∆VN W I = We − Wp Bw
145
6.1.6 General Material Balance Equation
Having analyzed all the individual terms in the material balance equation, we
can write,
Note that the two gas production terms are additive and equal to the total gas
production at the surface ie.,
One of the most important uses of the material balance equation is to calculate
water influx into a reservoir. This only requires that we know the volume of initial
fluids in-place, reservoir pressure and cumulative oil, gas and water production.
Cumulative water influx is,
µ ¶
N Boi
We = N Boi − (N − Np )Bo − (cf + Swi cw ) (pi − p)
1 − Swi
−GBg + GBgi + Gp Bg − {N Rsi − (N − Np )Rs }Bg
+Wp Bw (6.3)
146
Example 6.6 - Calculation of water influx from material balance
[MBE.mcd]
Using the results of the Examples 2,3,4 and 5, find the water influx when the
pressure falls from 1225 psig to 900 psig. Cumulative water production at this
time is 620,000 STB.
Data:
Wp = 0.62×106 [STB]
Bw = 1.0 [RB/STB]
Solution
µ ¶
N Boi
We = N Boi − (N − Np )Bo − (cf + Swi cw ) (pi − p)
1 − Swi
−GBg + GBgi + Gp Bg − {N Rsi − (N − Np )Rs }Bg
+Wp Bw
(6.4)
We = (101.64 − 83.63 − 4.24 − 11.50 − 0.15 + 0.62 × 1.0) × 106 = 2.74 × 106 RB
147
6.2 PRIMARY RECOVERY MECHANISMS
Each of the terms of the material balance equation represents a drive mech-
anism which contributes to the total energy required to produce oil from the
reservoir.
where,
The above indices represent the effectiveness of each drive mechanism for a par-
ticular reservoir.
A reservoir for which the dominant drive mechanism is, Iw , is called a water drive
reservoir.
A reservoir for which the dominant drive mechanism is, Igc , is called a gas cap
drive reservoir.
A reservoir for which the dominant drive mechanism is, Isg , is called a solution
gas drive reservoir.
148
Figure 6.8: Reservoir drive index as a function of time
A reservoir for which the dominant drive mechanism is, Ipd , is called a depletion
drive reservoir.
A reservoir for which more than one drive mechanism is important, is called a
combination drive reservoir.
The dominant drive mechanism for a particular reservoir can often be deduced
from the rate of pressure decline and the trend of the producing gas-oil ratio.
The trends which are observed when one of the mechanisms dominates are sum-
marized in the following figures.
1. Pressure depletion drive (fluid and rock expansion) results in a rapid straight
line pressure response and may be expected to recover less than 5% of the
original oil-in-place.
2. Solution gas drive — pressure drops slowly at first. As the producing GOR
increases, pressure falls rapidly. Ultimate recoveries are in the range 15-30
%.
149
Figure 6.9: Reservoir pressure as a function of cumulative oil production
150
Figure 6.11: Producing characteristics of gas cap drive reservoirs
3. Water drive — pressure declines rapidly at first, but the decline rate de-
creases as water influx from the aquifer increases. The producing GOR
remains approximately constant and ultimate recoveries are 50% or more.
151
Figure 6.12: Producing characteristics of solution gas drive reservoirs
152
6.3 USING MATERIAL BALANCE EQUA-
TIONS
The material balance equation describes the whole reservoir in terms of average
reservoir pressure, initial volumes of oil, gas and water in-place and cumulative oil,
water and gas production volumes. In order to use the material balance equation
it is necessary to determine average reservoir pressure for the time (cumulative oil,
water and gas production) when the material balance equation is to be applied.
Direct measurement of average reservoir pressure would require that all the wells
are shut-in and that the bottom-hole pressure is measured at a time after shut-in
which is sufficiently long for all the pressure gradients in the reservoir to equalize.
This may take months to years (depending on reservoir permeability) and result in
considerable loss in revenue because of lost production. The direct measurement
approach is therefore impractical.
Pressure data obtained from a pressure buildup test can be used to estimate
the average pressure in the volume or area drained by the tested well. These
tests require short test times (hours to days) and allow reservoir pressure to be
mapped over the field. The mapped pressures may be averaged to give the average
reservoir pressure as, P
pj Vp j
p= P (6.6)
Vp j
where pj and Vp j are the drainage area pressure and pore volume drained by well
j.
When solving the material balance equation the parameters may be classified into
the following groups of knowns and unknowns.
knowns unknowns
Np N
Gp G
Wp We
Swc p (Bo , Bg , Rs )
cw cf
Bw
153
The PVT properties (Bo , Bg , Rs ) may be considered to be known if the aver-
age reservoir pressure is known and representative fluid samples have obtained
and analysed. This reduces the number of unknowns to five but we have only
one equation. This is the central problem with the use of the material balance
equation.
Knowns
Np - this is usually known because oil is the primary production target which is
sold to generate revenue.
Gp , Wp - cumulative gas and water production be unknown for older oil and gas
fields because they had little or no value at the time of production. When these
are unknown it is not possible to perform material balance calculations for the
reservoir.
Unknowns
N, G - volumetric estimates of the original oil and gas-cap volumes in-place are
always known from the field appraisal stage. These are disregarded as soon as
production-pressure data becomes available and an attempt is made to estimate
in-place volumes from material balance calculations. This is because volumetric
estimates include all the mapped hydrocarbon volume, whereas material balance
calculation provides the effective volume or the volume which contributes to ac-
tual production. This will usually be smaller than the volumetric estimate due
to compartmentilization of the reservoir by faults or low permeability zones.
154
to considerable subsidence at the surface. This may be of little consequence on
land in remote areas but may cause serious problems for operations offshore.
Problem 6.1 Calculating water influx from material balance for history matching
aquifer performance
The reservoir for this exercise is a small offshore oil field which has been on-stream
for only 700 days. The field was shut-in for a 250 day period for upgrading of the
gathering system and production facilities. There was a strong and clear aquifer
response to the shut-in (use Mathcad to plot the field pressure as a function of
time to see the response).
PRODUCTION HISTORY
Time P Np Gp Wp
(day) (psia) (MMSTB) (BSCF) (MMSTB)
155
The initial oil in-place is estimated (volumetrically) to be 33.2 MMSTB.
PVT data for the reservoir oil is given in the following table.
PVT DATA
P Bo Rs Bg Bw
(psia) (RB/STB) (SCF/STB) (RB/SCF) (RB/STB)
Determine the cumulative water influx for each of the 50 day time periods in the
production history table.
Solution hint
You need to calculate a cumulative water influx volume for each 50 day period
(a total of 14 calculations). Each calculation is identical to the calculations
performed in Examples 6-1 to 6-6. You can simply use [MBE.mcd] to do the
calculation for each period. Alternatively, you could modify [MBE.mcd] to read-
in the production data and do the 14 calculations in one pass or prepare your
owm spreadsheet using whatever software you are most comfortable with.
156
6.4 MATERIAL BALANCE FOR A CLOSED
OIL RESERVOIR
When water influx from the aquifer is small or negligible (small ineffective aquifer,
weak to moderate aquifers during early stages of production when the aquifer
response is small) there is negligible water production and the material balance
equation reduces to,
µ ¶
N Boi
0 = N Boi − (N − Np )Bo − (cf + Swi cw ) (pi − p)
1 − Swi
−GBg + GBgi + Gp Bg − {N Rsi − (N − Np )Rs }Bg
(6.7)
If the original gas cap volume may be estimated from a volumetric calculation,
the formation compressibility is known, and reliable production-pressure data is
available, the only unknown is the original oil in-place, N . This provides a very
valuable check on the volumetrically determined value. As discussed previously,
the material balance derived value of N may be more reliable than the volumet-
rically determined volume.
After the original oil in-place has been established, the material balance equation
may be used to predict future reservoir pressure if future cumulative production
can be estimated. The main difficulty with this procedure is estimating the vol-
umes of gas and water which will accompany the specified oil production volume.
If all the produced oil and water is reinjected, this difficulty is eliminated.
157
Problem 6.2 - Calculation of original oil in-place using material balance
equation [OIPMBE.mcd]
The discovery pressure of a reservoir containing a gas cap was 3330 psia. Geo-
logical evidence suggests that aquifer quality is poor and that water influx into
the reservoir is likely to be negligible. The reservoir was produced until the reser-
voir fell to 2700 psia. Cumulative oil production at this time is 11.503 MMSTB
and cumulative gas production is 14.206 BSCF. The volumetric estimates of the
original oil-in-place, (N ), is 105 MMSTB and the initial gas cap volume is 81.14
BSCF. Does the material balance calculation confirm this estimate?
Data:
Swi = 0.21
cf = 3.0×10−6 [psi−1 ]
cw = 3.0×10−6 [psi−1 ]
Solution hints
158
6.5 MATERIAL BALANCE FOR A CLOSED
GAS RESERVOIR
The material balance equation for a closed gas reservoir is so simple that it may
be solved graphically. The graphical solution method is commonly referred to as
the P/z-plot. The plot can be used to estimate the original gas in-place and to
predict future reservoir pressure given a production forecast.
The general material balance equation for a closed gas reservoir reduces to;
we can write for the above material balance equation (where reservoir temperature
is assumed to remain constant),
µ ¶ µ ¶
zi T zT
G 5.02 × 10−3 = (G − Gp ) 5.02 × 10−3
Pi P
The above equation results in a straight line relationship between (P/z) and
Gp . The straight line on a (P/z)—Gp plot passes through (P/z)i at Gp = 0 and
through G at (P/z) = 0.
159
Figure 6.14: p/z plot for a closed gas reservoir
Example 6.7 - Calculation of initial gas in-place for a closed gas reser-
voir [GIP.mcd]
Estimate the initial gas content, G, for a closed gas reservoir having the following
production history.
3500 0 0.84
3350 46.7 0.82
3200 125.0 0.81
3050 203.5 0.80
2750 380.0 0.78
160
Solution
1. Calculate P/z for each pressure point and plot against cumulative produc-
tion, Gp .
2. Draw the best-fit straight line through the data and extrapolate to P/z = 0.
The intercept at P/z = 0 is the initial gas in place, G. To see this plot
open [GIP.mcd].
G = 2400 MMSCF.
161
Figure 6.15: Material balance for a gas reservoir
When a gas reservoir is in contact with a significant aquifer, water influx will
occur as the reservoir pressure declines with production. The material balance
for such a reservoir may be written as,
GBgi = (G − Gp )Bg + We − Wp Bw
We = GBgi − (G − Gp )Bg + Wp Bw
162
Figure 6.16: p/z plot for a gas reservoir experiencing water influx
The following pressure production data were recorded for a gas reservoir. Can
we estimate G from this data?
3500 0 0.84
3350 52 0.82
3200 155 0.81
3050 425 0.80
2950 880 0.79
Solution hint
Even if the aquifer is active, it takes time for the aquifer to respond to the decrease
in reservoir pressure. This means that early in the life of the reservoir will behaive
like a closed system. The early data should therefore plot as a straight line on a
163
P/z-plot. Extrapolating this plot to zero pressure will therefore give a realistic
estimate of the original gas-in-place. I have setup the spreadsheet [GIP.mcd] to
allow you to select the points through which to fit the straight line.
For the water drive gas reservoir of the previous example calculate the cumulative
water influx corresponding to the times at which cumulative gas production is
given. Cumulative water production is zero for the period and the reservoir
temperature is TR = 275 o F.
Solution hint
Do this any way you like. I used [GIP.mcd] from the previous example and added
a calculation for Bg from z and the material balance equation for a water drive
gas reservoir.
164
Chapter 7
RESERVOIR ROCK
PROPERTIES AND CORE
ANALYSIS PROCEDURES
1. Porosity.
2. Permeability.
3. Rock compressibility.
4. Saturation dependent properties.
— Relative permeability.
— Capillary pressure.
— Wettability.
In this section we look at the basic properties - porosity, permeability and com-
pressibility. The saturation dependent properties will be considered in the next
chapter.
7.1 POROSITY
Parameter Symbol Definition
Porosity φ The total fraction of the bulk volume which is void space
165
well sorted sandstone poorly sorted sandstone
21.5% 1%
Porosity for both sandstones and limestones can be greatly modified by post-
depositional events or digenesis. Cementation, chemical action, and fracturing
are events which can modify the original porosity of rocks. The original porosity
of a formation is usually refereed to as primary porosity. Porosity modified by
post-depositional processes is referred to as secondary porosity.
The attached figures show the effect dispersed fines (particulate kaolinite, pore-
lining chlorite and pore-bridging illite) affect primary porosity. Effective porosity
and permeability may be greatly reduced by deposition of fine particulate minerals
in the pore space.
166
Figure 7.2: Schematic of a clean well-sorted sandstone
Total porosity is the sum of effective and disconnected porosity. The total
porosity, φt , is given by,
bulk volume − grain volume total pore volume
φt = =
bulk volume bulk volume
167
Discrete- particle kaolinite Pore- lining chlorite Pore- bridging illite
Figure 7.3: Common types of dispersed shales, clays and fines and their effect on
porosity
The most common method employed to measure porosity is based on Boyle’s law.
The equipment used is called a Boyle’s law porosimeter and is shown schematically
in the attached figure. The apparatus and measurement procedure consists:
3. Valve B is opened and the two cells are allowed to equilibrate. The equi-
librium absolute pressure, (p2 + pa ), is recorded. This is called Condition
II.
168
Figure 7.4: SEM micrograph of pore-filling authigenic kaolinite (x1000)
p = absolute pressure
T = absolute temperature
V = volume
n = moles of gas
R = universal gas constant
169
Figure 7.5: SEM micrograph of chlorite (feldspar) lined pore (x1000)
Figure 7.6: SEM micrograph of delicate fibers of illite bridging pores (x1000).
These fibers may break-off at high flow rates and block pores
170
Figure 7.7: SEM micrograph of pore filling kaolinite plates (x1000).
Using the ideal gas law we write, for the above word equation,
Note that the pressures p1 and p2 are gauge pressures as read in the actual
experiment.
where the bulk volume of the sample, Vb , is either determined from measurements
of the sample dimensions (core plugs) or by measuring the displaced liquid volume
when the sample is immersed in a non-wetting liquid such as mercury.
171
Figure 7.8: Solution and fracture porosity in limestones
172
Figure 7.10: Schematic of Boyle’s law porisometer test procedure
[Answer: 0.23]
173
kA ∆P
q=
µ L
∆P
A
q q
7.2 PERMEABILITY
Parameter Symbol Definition
Permeability will usually vary over several orders of magnitude in the same reser-
voir. The variation in permeability (heterogeneity) has a great effect on oil recov-
ery for both conventional and EOR processes.
174
Figure 7.12: Schematic of permeameter
The steady-state flow rate (q) of a fluid which completely saturates the core is
directly proportional to the x-sectional area (A) over which the flow occurs, the
imposed pressure gradient over the core (∆p/L) and inversely proportional to the
viscosity of the fluid. µ ¶
∆p 1
q∝A
∆L µ
175
When the variables in the above equation are expressed in Darcy units, the com-
puted permeability has the units of darcys. A rock sample has a permeability of
one darcy when;
The darcy unit is too large for most reservoir rocks and it is common practice to
express permeability in terms of millidarcys.
Field Units
In oil field units the linear form of Darcy’s Law for the flow of an incompressible
fluid is written as,
kA∆p
q = 0.001127
µ∆L
where,
∆p = pressure difference, psi
∆L = flow length, ft
A = x-sectional area, ft2
q = volumetric flow rate, res. bbl/day (RB/D)
µ = viscosity, cp
k = permeability, md
176
Example 7.2 - Laboratory determination of the liquid permeability of
a core plug [LPERM.mcd]
Solution hint
Use
qµ∆L
k=
A∆p
to calculate the permeability. Since a liquid is used to measure it, the permeability
is called the liquid permeability.
177
Example 7.3 - Calculation of field flow rates [LINQ.mcd]
The core plug in the previous example was taken from a reservoir undergoing a
horizontal line drive over a flow length of 10,000 feet. Production well spacing is
1000 feet and the sand thickness is 30 feet. The reservoir oil has a viscosity of
0.8 cp. What is the well rate when the pressure difference between injectors and
producers is 500 psi?
Solution hint
Use
kA∆p
q = 0.001127
µ∆L
to calculate the rate in RB/day if you are not using Mathcad which handles mixed
systems of units automatically. The constant 0.001127 arises from unit conver-
sions. Study [LINQ.mcd] to see how Mathcad handles the unit conversions.
178
7.2.2 Laboratory Measurement of Permeability
The experiment consists of flowing a gas through the core plug. Since gas is
compressible, the previous equations, which are valid only for incompressible
fluids, must be modified. The average gas pressure (p̄) in the core is given by,
(p1 + p2 )
p̄ =
2
Assuming that the gas is ideal - a reasonable assumption if the pressures are
low, the product qp (equivalent to V p for a static system) is constant. We can
therefore express the volumetric flow rate at the average pressure (q̄), in terms of
the measured volumetric flow rate at atmospheric conditions (qa ),
qa pa = q̄(p1 + p2 )/2
qa pa
q̄ =
(p1 + p2 )/2
where pa is atmospheric pressure.
We use this equation to calculate the gas permeability of the test plug. When
his done at a number of different average pressures we find that the calculated
permeability is not constant but that it decreases with increasing pressure. This
may appear to be a problem, particularly if we expect the permeability to be
constant!
179
7.2.3 The Klinkenberg Effect
The apparent decrease in measured gas permeability which occurs with increasing
average flowing pressure is known as the Klinkenberg effect.
At very low pressures, the mean free path of gas molecules is similar to the di-
mensions of the pore space. Under these conditions the solid pore walls do not
significantly retard gas flow close to the pore walls because molecules spend little
time at the walls (free-slip condition).
For liquids and gases at very high pressure, molecules are always present at the
pore walls and the velocity of the fluid at the pore walls is zero (no-slip condition).
The measured permeability is therefore lower than that for gases at low pressure.
3. Extrapolate the linear plot to infinite pressure i.e. to 1/p̄ = 0. The extrap-
olated permeability is equivalent to the liquid permeability.
kliquid and b are determined from the slope and intercept of the plot.
kliquid = intercept
slope
b=
kliquid
The Klinkenberg correction may be quite significant for gas flow in:
180
Problem 7.1 - Laboratory determination of the liquid permeability of
a core plug using gas [KLINK.mcd]
Solution hint
Open [KLINK.mcd] , check the input data and read the answer.
181
πR4 ∆P kA ∆P πR4 ∆P
q = nq c = n = qc =
8µ L µ L 8µ L
The matrix consists of a solid block having dimensions L × L × L. The pore space
is made up of a total of n uniform capillaries of radius R and length L.
182
The total steady-state flow rate, q, is simply the sum of the flows in each capillary,
πR4 ∆P
q = nqc = n
8µ L
According to Darcy’s law, the flow q is given by,
kA ∆P
q=
µ L
where A is the x-sectional area of the porous medium perpendicular to the direc-
tion of flow.
kA ∆P πR4 ∆P
=n
µ L 8µ L
Eliminating the common parameters and rearranging to solve for permeability,
πR4
k=n
8L2
πR2
L2 = n
φ
R2 φ
k=
8
183
Defining the specific surface area per unit pore volume of the porous medium,
ΣV p , as
pore surf ace area
ΣV p =
pore volume
n2πRL
ΣV p =
nπR2 L
2
ΣV p =
R
or
2
R=
ΣV p
Defining the specific surface area per unit grain volume of the porous medium,
ΣV g , as
pore surf ace area
ΣV g =
grain volume
pore volume
ΣV g = ΣV p
grain volume
φ
ΣV g = ΣV p
1−φ
or
1−φ
ΣV p = ΣV g
φ
1 φ3
k=
2ΣV g (1 − φ)2
This is similar to the empirical Kozeny relation for unconsolidated porous media
and forms the basis for power-law correlations or transforms between porosity
and permeability for actual reservoir rocks. Actual relationships follow a power
law because in real porous media ΣV g depends on φ and k in a complex way.
184
∆P
q h3 W ∆P
q=
h 12µ L
W
L
kA ∆P kHW ∆P 1 2h 1
q= = k= h = h 2φ f
µ L µ L 12 H 12
The resultant stress, σ−P , causes a strain or deformation of the rock. The overall
result is that grain, pore and bulk volumes decrease with increasing stress.
The fractional change in grain volume per unit change in rock stress is called the
rock or matrix compressibility, cr .
1 dVr
cr =
Vr d(σ − P )
The fractional change in total or bulk volume per unit change in rock stress is
called the bulk volume compressibility, cb .
1 dVr
cb =
Vb d(σ − P )
The fractional change in pore volume per unit change in rock stress is called the
pore volume or formation compressibility, cp .
1 dVp
cp = −
Vp d(σ − P )
186
Figure 7.15: Relationships between porosity, permeability and rock microstruc-
ture
187
Figure 7.16: Measured porosity-permeability relationships for different rock types
188
Figure 7.18: Measured permeability-specific area relationships for different sand-
stones
The matrix, bulk and pore volume compressibilities are measured in special lab-
oratory experiments which will be described in the next section. For reservoir
engineering calculations the primary interest is in the change in pore volume as
reservoir or pore volume pressure changes.
Experimental measurements for sandstones and shales, in which the external rock
stress (σ) is constant, show that cr << cb . This means that,
dVb ≈ dVp
189
Figure 7.19: Hydrostatic load cell for measuring pore volume compressibility
For actual reservoir conditions only the vertical component of external stress
is constant with the stress components in the horizontal plane characterized
by boundary conditions that there is no bulk deformation in these directions.
Geersma (1966) showed that for these conditions,
1
cf ≈ cp
2
this shows that the effective pore volume compressibility for reservoir rocks is
only one-half of the value measured in laboratory tests.
190
Figure 7.20: Porosity and permeability as a function of stress
Typical results for various reservoir rock types are shown in attached figure.
191
7.4.3 Use of Rock Compressibilities
When oil, water and gas all occupy the pore space, (φ), in a unit bulk volume,
the volume of liquid which is expelled from the rock per unit drop in pressure
may be written as,
ct = So co + Sw cw + Sg cg + cf
where,
ct = total compressibility
cf = formation or pore space compressibility
co , cw , cg = oil, water and gas phase compressibilities
So , Sw , Sg = oil, water and gas phase saturations
The total compressibility is used to evaluate the diffusivity factor for unsteady-
state flow calculations. Estimates of total compressibility are important in well
pressure test analysis.
Typical Values
ct = So co + Sw cw + Sg cg + cf
ct = 64 × 10−6 psi−1
192
Figure 7.21: Porosity variation with depth in a sedimentary basin
193
Chapter 8
FLUID FLOW
All the equations used to describe the flow of fluids in reservoirs are based on
Darcy’s law. Darcy (1856), a French engineer, investigated the flow of water
through sand filters for water purification. He observed the following relationship
between superficial velocity and the properties of the sand bed and fluid,
q k ∆p
=−
A µ ∆L
where,
In the above equation the porous medium is saturated with a single fluid. The
linear dependence of flow rate on the pressure gradient implies laminar or viscous
flow in the pore-spaces of the porous medium. This is generally true for most
reservoir conditions where actual flow velocities are low. A common exception is
flow close to a wellbore where, as a result of the converging nature of the flow,
velocities may be high enough for turbulent or non-linear flow.
194
Figure 8.1: Darcy’s law and linear flow
The above equation is general and may be written in differential form as,
q k dp
=−
A µ dx
where dp/dx is the pressure gradient in the direction of flow
The negative sign in the above equations indicates that pressure decreases in
the direction of flow. The sign convention is therefore that distance is measured
positive in the direction of flow. This is the basic equation used to analyze single
phase flow in reservoir engineering.
The above form of Darcy’s law applies to horizontal flow where there are no
gravity effects. In reservoir analysis we are often interested in vertical or inclined
flow where the flow occurs in the presence of a hydrostatic gradient. In such cases
it is convenient to define a pressure potential as,
Z p dp
Φ= − gdz
pr ρ
where z is the vertical coordinate measured positive downward and g is the grav-
itational acceleration. pr is an arbitrary reference pressure, usually taken as
pr = 0.
195
Figure 8.2: Pressure potential and inclined linear flow
For a reservoir dipping upward in the direction of flow with dip angle α,
z = x sin α
Ψ = ρΦ = p − ρgz
196
Figure 8.3: Linear vertical flow problem
In order to test your understanding of Darcy’s law and fluid potential solve the
problem shown in Figure 8.3. If you are not using Mathcad be careful with units.
The linear flow system is depicted in the attached figure. The medium has uniform
permeability, k, and is saturated with an incompressible (ρ is constant) fluid
having constant viscosity, µ. Darcy’s law is written as,
kA ∆p
q=−
µ L
This equation is commonly used to evaluate flow tests in reservoir core samples
and calculate rates in line drives.
197
Figure 8.4: Linear flow in parallel
Consider the case where the flow system consists of a n layers having different
thicknesses, hi , and permeabilities, ki . For a common inlet face pressure, P1 , and
outlet face pressure, P2 , the pressure drop across each layer is the same and the
flow rate for each layer is,
ki (hi w) (P2 − P1 )
qi = −
µ L
The total flow rate is n
X
q= qi
i=1
or n
w(P2 − P1 ) X
q=− ki hi
µL i=1
Darcy’s law for the total flow may also be written as,
k̄(hw) (P2 − P1 )
q=−
µ L
198
Figure 8.5: Linear flow in series
Determine the average permeability of four parallel beds having the following
thicknesses and permeabilities.
Consider the arrangement where the different permeabilities are arranged in se-
ries. For this arrangement the flow through each layer is the same,
q = qi
where,
ki (hw) ∆Pi
q=−
µ Li
199
where ∆Pi is the pressure drop across slab i. This may be rewritten as,
qµ Li
∆Pi =
hw ki
and the total pressure drop is the sum of the pressure drops in each layer,
n
X n
qµ X Li
(P1 − P2 ) = ∆Pi =
i=1 hw i=1 ki
This equation is used to calculate the effective vertical permeability for a layered
reservoir system.
Determine the average permeability of four beds in series having the following
lengths and permeabilities.
[Answer: 80 md]
200
Figure 8.6: Radial flow model
The radial flow system is depicted in the attached figure. This is the basic
model for flow into a well and is used in reservoir engineering to evaluate well
performance. The following nomenclature employed,
rw = wellbore radius
re = well drainage radius
h = formation thickness
Flow enters the system across the outer perimeter at radius re , and leaves at the
wellbore of radius rw . The volumetric flow rate, q, is constant and the flow area,
A, is 2πrh.
201
Separating variables and integrating gives:
Z re dr 2πkh Z pe
q = dp
rw r µ pw
2πkh(pe − pw )
q(ln rw − ln re ) =
µ
Solving for q,
2πkh (pe − pw )
q=
µ ln rrwe
This equation is widely used in reservoir engineering to calculate production and
injection rates for individual wells.
kh(pe − pw )
q = 0.00708
µ ln rrwe
where,
202
Figure 8.7: Pressure distribution in steady-state radial flow
Calculate the maximum possible pumping rate for an oil well in a reservoir where
the pressure is being maintained at 2000 psia at the drainage radius. The following
data apply:
k = 230 md
h = 10 feet
µ = 3.5 cp
rw = 0.5, feet
re = 2000, feet
Solution hint
Study [RADSSF.mcd] carefully - you will be using it a lot. It solves a great variety
of radial flow problems and does many vertical well performance calculations.
Since we have only studied steady-state flow to this point, take the answer for this
equation and ignore the other equations and results. The theoretical minimum
flowing bottom hole pressure for a pumped well is one atmosphere.
203
Figure 8.8: Radial flow in series
This arrangement results in the same expression for effective or average perme-
ability as that for linear flow.
Using the same reasoning as for linear flow in series yields the result,
XM
1 1 log(ri )/(ri−1 )
=
k̄ log(re /rw ) i=1 ki
204
Figure 8.9: Radial flow in parallel
205
Example 8.4 - Average permeability for radial beds in series
[RADSERK.mcd]
Determine the average permeability of four radial layers in series having the
following radial distances to bed boundaries and bed permeabilities. The wellbore
radius is 0.5 ft and the well drainage radius is 2000 ft.
Wells are always drilled with overpressure (mud pressure greater than formation
pressure) to prevent inflow of reservoir fluids which could lighten the mud column
and lead to a blowout.
As a result of overpressure some of the drilling mud flows into the formation and
the particles suspended in the mud partially plug the pore spaces through which
fluid flows. This creates a lower permeability zone or a damaged zone close to
the wellbore.
Wellbore damage is depicted in the attached figure, where ra is the radius of the
damaged zone. The damaged zone results in an additional pressure ∆pskin at the
wellbore. This pressure drop simply adds to that for the case of no damage.
For steady-state radial flow, the pressure drop for an undamaged well is given by,
2πkh (pe − pw )
q=
µ ln rrwe
or µ ¶
qµ re
pe − pw = ln
2πkh rw
206
Figure 8.10: Radial flow model with an altered or damaged zone
If the additional pressure drop due to the damaged zone is ∆pskin , then the total
pressure drop for a damaged well may be written as,
µ ¶
qµ re
pe − pw = ln + ∆pskin
2πkh rw
If we write,
qµ
∆pskin = (s)
2πkh
Than, for a damaged well we have a modified radial flow equation,
µ ¶
qµ re
pe − pw = ln +s
2πkh rw
or
2πkh (pe − pw )
q=
µ ln rrwe + s
where s is the skin-factor for the well.
In the above equations the rate, q, is the reservoir or sandface rate. In appli-
cation of the radial flow equation to wells we usually specify the rate at surface
207
conditions. When this is done we write the radial flow equation as,
2πkh (pe − pw )
q=
µB ln rrwe + s
where B is the formation volume factor which relates surface rates to reservoir
rates. It is understood that when an equation contains B the rate, q, is in surface
volumes. In the absence of B, the rate is understood to be in reservoir volumes.
208
Figure 8.11: Skin pressure drop
209
Example 8.5 - Steady-state radial flow with skin [RADSSF.mcd]
(i) Calculate the maximum possible pumping rate for an oil well in a reservoir
where the pressure is being maintained at 2000 psia at the drainage radius.
A well test has shown the well to be highly damaged with a skin factor of
+7.
The following data apply:
k = 230 md
h = 10 feet
µ = 3.5 cp
rw = 0.5, feet
re = 2000, feet
(ii) What would the well rate be if the wellbore is cleaned with an acid. A suc-
cessful acid job may be expected to reduce the skin factor to approximately
zero.
(iii) What would the rate be for a stimulated well after a frac job which is
expected to achieve a skin factor of -3.
[Answer: (i) 604 RB/day, (ii) 1114 RB/day, (iii) 1745 RB/day]
The skin factor for a stimulated well ,where the skin factor is negative, has an
upper limit on the magnitude of the actual value which the skin factor can take.
This may be demonstrated by considering the steady-state radial flow equation,
2πkh (pe − pw )
q= ³ ´
µB ln re + s
rw
If −s is equal to, or greater than, ln(re /rw ), the equation produces answers which
are physically impossible. This problem is removed by the introduction of the
thick skin model.
210
Figure 8.12: Realatinship between skin-factor and the size of the altered zone
If the altered zone extends from rw to ra and the altered permeability is ka , and if
the bulk formation permeability (from ra to re ) is k, we can use the steady-state
radial flow equation to calculate the pressure drops across the altered zone and
the formation, µ ¶
qBµ ra
pa − pw = ln
2πkh rw
where ra is the radius of the altered zone and pa is the pressure at ra .
Also, µ ¶
qBµ re
pe − pa = ln
2πkh ra
where re is the drainage radius and pe is the pressure at re .
Adding the two equations gives the pressure across the formation (pe − pw )
½ µ ¶ µ ¶¾
qBµ 1 re 1 ra
pe − pw = ln + ln
2πh k ra ka rw
The thin skin model expresses the above pressure drop as,
½ µ ¶ ¾
qBµ re
pe − pw = ln +s
2πkh rw
211
where k is the permeability of the bulk formation and s is the skin factor. This
may be re-written as,
½ µ ¶ ¾
qBµ 1 re 1
pe − pw = ln + s
2πh k rw k
Equating the two expressions for (pe − pw ) gives,
½ µ ¶ µ ¶¾ ½ µ ¶ ¾
1 re 1 ra 1 re 1
ln + ln = ln + s
k ra ka rw k rw k
This may be simplified to give,
" # µ ¶
k ra
s= − 1 ln
ka rw
212
This may be simplified to,
rw0 = rw e−s
The effective wellbore radius concept is often used to characterize fractured and
horizontal wells. For example, the effective wellbore radius for a vertical well with
an infinite conductivity fracture is,
rw0 = xf
The effective wellbore radius for a long horizontal well in a thin reservoir ap-
proaches that of a fractured well with a fracture half-length equal to one-quarter
the length of the horizontal well,
L
rw0 =
4
where L is the length of the horizontal well.
Once a numerical value for the skin factor has been determined it can be used to
determine the well flow efficiency F E. This is defined as the ratio of the pressure
drop at the damaged wellbore to that for an undamaged well,
pi − pwf − ∆ps qactual
FE = =
pi − pwf qundamaged
213
Problem 8.2 - Skin-factor [SKIN.mcd]
If the fracture is estimated to affect a zone extending 15 ft. into the formation
estimate the permeability of the affected zone. [Answer: 255 md.]
214
Figure 8.13: Transient radial flow
The basic equation which describes single phase unsteady-state flow in a radial
system is the radial diffusivity equation.
à !
1 ∂ kρ ∂p ∂p
r = φcρ
r ∂r µ ∂r ∂t
where c is the total system compressibility, t is time and ρ is the fluid density.
The independent variables are time (t) and spatial position (r). The dependent
variable is pressure (p). Pressure is a function of both space and time i.e., p =
p(r, t). The partial differential equation is non-linear because the coefficients
(particularly the density, ρ) are functions of pressure.
215
Figure 8.14: Pressure distribution in transient radial flow
The radial system is similar to that described for steady-state flow. We make the
following assumptions:
216
Figure 8.15: Differential material balance for the radial diffusivity equation
∂(qρ) ∂ρ
= 2πrhφ
∂r ∂t
this is called the continuity equation.
217
The term ∂ρ/∂t may be expressed in terms of pressure by introducing an equation-
of-state for the fluid. Defining the isothermal compressibility of the fluid as
1 ∂V
c=−
V ∂p
1 ∂ρ
c=
ρ ∂p
This may be written as,
cρ∂p = ∂pρ
dividing both sides of the equation by ∂t, gives
∂p ∂ρ
cρ =
∂t ∂t
This is the general form of the radial diffusivity equation for the flow of a single
phase in a porous medium. The equation is non-linear because density, ρ, which
is one of the coefficients is a function of pressure p.
218
8.3.2 Liquids Having Small and Constant Compressibility
Reservoir oil and water are relatively incompressible and the assumption of con-
stant and small compressibility is a good model for these fluids. Since we have
assumed that k, φ, µ and c are constant, the diffusivity equation becomes
à !
1 ∂ ∂p φcρµ ∂p
ρr =
r ∂r ∂r k ∂t
Using the chain rule for differentiation, we expand the LHS of the equation,
à !
1 ∂(ρr) ∂p ∂ 2p φcρµ ∂p
+ ρr 2 =
r ∂r ∂r ∂r k ∂t
à !
1 ∂(ρ) ∂p ∂(r) ∂p ∂2p φcρµ ∂p
r +ρ + ρr 2 =
r ∂r ∂r ∂r ∂r ∂r k ∂t
à !
1 ∂ρ ∂p ∂p ∂2p φcρµ ∂p
r + ρ + ρr 2 =
r ∂r ∂r ∂r ∂r k ∂t
This is simplified to
à !2
∂p 1 ∂p ∂ 2 p φµc ∂p
c + + 2 =
∂r r ∂r ∂r k ∂t
219
∂p/∂r is small and since c << 1, the leading term on the LHS of the above
equation may be neglected and the diffusivity equation becomes
1 ∂p ∂ 2 p φcµ ∂p
+ 2 =
r ∂r ∂r k ∂t
This is the final form of the diffusivity equation for a slightly compressible fluid.
The equation is linear and therefore amenable to analytical solution. It forms the
basis for many important reservoir analysis techniques which include transient
pressure well test analysis and aquifer modeling.
In actual applications of the above equation to single phase oil flow where the
formation contains connate water and the formation is itself compressible, the
compressibility, c, is the total compressibility of the system. This is determined
using the following equation
c = co So + cw Sw + cf
where co , cw and cf are the oil, water and pore volume or formation compressibil-
ities, respectively. So and Sw are the oil and water saturations. Typical values
may be
co = 10 × 10−6 psi−1
cw = 3 × 10−6 psi−1
cf = 6 × 10−6 psi−1
Sw = 0.20
p = 3000 psi
This results in
c = 14.6 × 10−6 psi−1
220
8.3.3 Pseudo-Steady-State Radial Flow
The simplest solution to the radial diffusivity equation (other than the steady-
state solution) is for pseudo-steady-state flow. Pseudo-steady-state flow is a spe-
cial form of stabilized unsteady-state flow in which the shape of the pressure
profile from the wellbore to the drainage radius is independent of time, but the
average drainage area pressure declines with production.
The value for the constant is obtained from the material balance equation written
above. Differentiating this equation we obtain,
or
dp̄ dp q
= =−
dt dt cVp
For the radial model, Vp = πre2 hφ, thus
∂p q
=−
∂t cπre2 hφ
221
The radial diffusivity equation is
à !
1 ∂ ∂p φµc ∂p
r =
r ∂r ∂r k ∂t
à !
1 ∂ ∂p φµc q
r =−
r ∂r ∂r k cπre2 hφ
which simplifies to à !
1 ∂ ∂p qµ
r =−
r ∂r ∂r πre2 kh
This equation may be written as
à !
∂p qµ
∂ r =− r∂r
∂r πre2 kh
Integrating the above equation gives,
∂p qµr2
r =− + C1
∂r 2πre2 kh
The constant of integration, C1 , is easily evaluated from the first BC
i.e., r∂p/∂r = 0 at r = re
qµ
C1 =
2πkh
Substituting for C1 , and simplifying gives
à !
∂p qµ 1 r
= − 2
∂r 2πkh r re
Separating variables, Ã !
qµ 1 r
∂p = − 2 ∂r
2πkh r re
Integrating, Ã !
Z pr qµ Z r 1 r
∂p = − 2 ∂r
pw 2πkh rw r re
" #r
qµ r2
[p]pprw = ln r − 2
2πkh 2re rw
or à !
qµ r r2 r2
pr − pw = ln − 2 + w2
2πkh rw 2re 2re
222
The term rw2 /re2 is clearly negligible and the equation is written as,
à !
qµ r r2
pr − pw = ln −
2πkh rw 2re2
2πkh (pe − pw )
q=
µB ln(re /rw ) − 12 + s
The term ln(re /rw ) has a value typically between 6 and 7. The rates predicted by
the steady-state and the pseudo steady-state equations are usually very similar
(within 10%).
A problem with using the above radial flow equations is that although pw and q
can be measured directly, the pressure at the outer drainage radius, pe , cannot.
Well tests provide a measure of the average drainage area pressure and it is there-
fore more convenient to express the pressure drawdown in terms of the average
reservoir, p̄.
223
Now, dVp = 2πrhφdr, so R re
p2πrhφdr
p̄ = Rrwre
rw 2πrhφdr
R re
prdr
p̄ = Rrwre
rw rdr
or Z re
2
p̄ = 2 prdr
re − rw2 rw
Since re2 − rw2 ≈ re2
2 Z re
p̄ = 2 prdr
re rw
For pseudo-steady-state flow,
à !
qµ r r2
pr − pw = ln − 2
2πkh rw 2re
or à !
qµ r r2
p = pw + ln − 2
2πkh rw 2re
Therefore,
à !
2 Z re 2 Z re qµ r r2
p̄ = 2 pw rdr + 2 ln − rdr
re rw re rw 2πkh rw 2re2
à ! à !
2 re2 rw2 2 qµ Z re r r2
p̄ = 2 pw − + 2 r ln − dr
re 2 2 re 2πkh rw rw 2re2
224
Again, neglecting small terms,
Z µ ¶
re r r2 re r2
r ln dr = e ln − e
rw rw 2 rw 4
Integration of the second term gives;
Z " #re
re r3 r4 re2
dr = =
rw 2re2 8re2 rw
8
Simplifying, µ ¶
qµ re 1 1
p̄ = pw + ln − −
2πkh rw 2 4
µ ¶
qµ re 3
p̄ − pw = ln −
2πkh rw 4
The pseudo steady-state equation for a well centered in a circular drainage area,
2πkh (p̄ − pw )
q=
µB ln(re /rw ) − 34 + s
2πkh (p̄ − pw )
q= q
µB ln( 2.2458A/(CA r2 ) + s
w
225
where CA is the Dietz shape factor which depends on the geometry of the drainage
area. Values for the shape factor are given in various handbooks and texts.
Calculate the production rate of an oil well in a 160 acre drainage area when the
average pressure is 1850 psia.
What would the rate be using the steady-state solution? [Answer: 721 STB/day]
226
Shape of drainage area CA CA
31.6
1 10.8
2
4.86
30.9
2.07
31.6
1 2.72
4
0.232
27.6
0.115
27.1
60o
3.39
21.9
1/3
1 3.13
1
2
1 22.6
0.607
2
1 5.38
4 1
0.111
2
1 2.36
5
0.098
12.9
In water drive reservoirs
19.1
4.57
In reservoirs of unknown production character
25
227
Figure 8.17: Approximating complex geometries
In cases where the flow geometry is more complex than those considered by
the Dietz shape factors, it is usually possible to approximate the system using
simple idealizations. An example of this is shown in the attached figure for a
well completed close to the intersection of two linear sealing faults. If the angle
between the faults is θ and the flow is assumed to be steady-state, the well rate
is given by,
2πkh (pe − pw )
q=f ³ ´
µB ln re
rw
where,
θ
f=
360o
The above equation is based on the fact that every streamline in a radial flow
system can represent a no-flow boundary.
228
8.4 WELL PRODUCTIVITY
The productivity index for a well is not constant and may vary considerably over
the life of the well. To see why this is so, consider the pseudo-steady-state radial
flow equation,
2πkh(P̄ − Pw )
q=
µB(ln( rrwe ) − 34 + s)
So,
q 2πkkro h
J= =
(∆p) µBo (ln( rrwe ) − 34 + s)
The above equation may be grouped into those parameters which remain constant
with time and those which change with time,
à !à !
2πkh kro
J=
(ln( rw ) − 34 + s)
re
µBo
The terms kro /µBo vary with time because reservoir pressure ( which affect µ
and Bo ) and saturation ( which affects kro ) change with time. Moreover, if the
well is stimulated or if it gradually cleans-up with production, s will also change
with time.
Increasing Well PI
The above equation shows the options available to increase well productivity are:
229
Figure 8.18: Partial penetration
The well models discussed above considered a well completed over the entire
section of the reservoir. Many oil and gas wells are completed over only part of
the producing sand interval. These wells are referred to as partially penetrating
wells.
When comparing a partially penetrating well to a fully penetrating well, the flow
in the vicinity of a partially penetrating well must deviate from pure radial flow
as streamlines converge towards the well. This results in an additional pressure
drop close to the wellbore which can be treated as a pseudo-skin due to partial
penetration.
230
A number of correlations have been published which account for the effect of
partial penetration on well performance. All are based on potential flow solutions
or numerical simulations for the two-dimensional cylindrical diffusivity equation
in two-dimensions. The correlation by Papatzacos (1988) is typical. For this
correlation the pseudo-skin factor, sp , is given by (see attached figure for definition
of variables),
à ! à ! " µ ¶0.5 #
1 πhD 1 hpD A−1
sp = − 1 ln + ln
hpD 2 hpD 2 + hpD B−1
where,
hp
hpD =
h
s
h kh
hD =
rw kv
h
A=
h1 + 0.25hp
h
B=
h1 + 0.75hp
2πkh h 1
J=
µB ln re /rw − 0.75
than the ratio J/Jpp is readily calculated. As a rule of thumb, this ratio is
approximately hp /h.
231
Problem 8.4 - Partially penetrating well [PARPEN.mcd]
[Answer: (i) 7.8 STB/day-psi, 1.0 (ii) 6.2 STB/day-psi, 0.8, (iii) 4.4 STB/day-psi,
0.57, (iv) 2.5 STB/day-psi, 0.32, (v) 0.69 STB/day-psi, 0.09, (vi)4.4 STB/day-psi,
0.57]
232
8.5 GAS FLOW
This is the basic material balance for a radial volume element of the reservoir
and it applies to all flows.
For the case of a slightly compressible fluid with constant viscosity, we have
previously written the radial diffusivity equation as,
à !
1 ∂ ∂p φµc ∂p
r =
r ∂r ∂r k ∂t
Gases are highly compressible and we cannot expect that the above diffusivity
equation will apply for gases.
233
Since
m
n=
M
where m is the mass of the gas and M is the gas molecular weight, the real gas
law may be written as,
m M p
ρ= =
v RT z
We may use this expression together with the definition of compressibility to
write an expression for the compressibility of a real gas,
1 ∂ρ
c=
ρ ∂p
which gives
z ∂(p/z)
c=
p ∂p
In performing the integration we note that z = z(p).
( )
z ∂
c= (pz −1 )
p ∂p
( )
z 1 p ∂z
c= − 2
p z z ∂p
Finally,
1 1 ∂z
c= −
p z ∂p
i.e., the compressibility of a gas is a highly non-linear function of pressure.
As previously, we begin our analysis for a gas by writing the continuity equation,
à !
1 ∂ ρ ∂p φ ∂ρ
r =
r ∂r µ ∂r k ∂t
Since
M p
ρ=
RT z
234
we have à ! à !
1 ∂ M p 1 ∂p φ ∂p ∂ρ
r =
r ∂r RT z µ ∂r k ∂t ∂p
Now, from our definition of compressibility,
∂ρ
= cρ
∂p
∂ρ M p
=c
∂p RT z
which gives à !
1 ∂ M p 1 ∂p φ ∂p M p
r = c
r ∂r RT z µ ∂r k ∂t RT z
dividing both sides by the constants we finally obtain,
à !
1 ∂ p ∂p φcp ∂p
r =
r ∂r µz ∂r kz ∂t
Pseudo-pressure
235
therefore, Ã !
1 ∂ p ∂ψ µz φcp ∂ψ µz
r =
r ∂r µz ∂r 2p kz ∂t 2p
Simplifying this expression gives
à !
1 ∂ ∂ψ φµc ∂ψ
r =
r ∂r ∂r k ∂t
This has eliminated the non-linearity on the LHS and made the equation look
like the diffusivity equation for a slightly compressible liquid except that the
coefficient on the RHS is still non-linear (c is a function of pressure).
µz ≈ constant = µ̄z̄
If we are doing the analysis by hand and wish to eliminate the need to evaluate
pseudo-pressures we may simply write the equation in terms of p2 .
∂ψ 1
=
∂(p2 ) µ̄z̄
236
and à !
1 ∂ ∂(p2 ) ∂ψ φµ̄c̄ ∂(p2 ) ∂ψ
r =
r ∂r ∂r ∂(p2 ) k ∂t ∂(p2 )
which gives à !
1 ∂ ∂(p2 ) φµ̄c̄ ∂(p2 )
r =
r ∂r ∂r k ∂t
The result is identical to that which would be obtained by defining
ψ = p2
237
8.5.3 ∆p is not small
When ∆p is not small, c and µ vary considerably and we cannot use average
values for these parameters over the flow conditions.
A problem with the pseudo-time it does not have units of time and this is unde-
sirable in actual practice where the engineer likes to relate time to distance via
the depth of investigation concept.
Again, this equation has exact ally the same form as the diffusivity equation for
a slightly compressible fluid.
238
8.5.4 Steady and Pseudo-Steady State Radial Gas Flow
To evaluate the value of the constant of integration, C1 , we write Darcy’s law for
radial flow,
2πkh ∂p
q= r
µ ∂r
where q is the rate at reservoir conditions. The rate at surface conditions is given
by
2πkh ∂p
qsc = r
µBg ∂r
where Bg is the gas formation volume factor which is given by
µ ¶
psc zT
Bg =
Tsc p
Substituting for Bg gives
à !
2πTsc kh p ∂p
qsc = r
psc µ zT ∂r
The equation is written in terms of pseudo-pressure as
à !
2πTsc kh p ∂ψ dp
qsc = r
psc µ zT ∂r dψ
From the definition of pseudo-pressure
dp µz
=
dψ 2p
239
Substituting for dp/dψ gives
à !
πTsc kh ∂ψ
qsc = r
psc T ∂r
or, µ ¶
∂ψ psc qsc T
r =
∂r πTsc kh
Separating variables, Ã !
∂r πTsc kh
= ∂ψ
r psc qsc T
Integrating, Ã !
Z rw ∂r πTsc kh Z ψw
= ∂ψ
re r psc qsc T ψe
gives à !
µ ¶
re πTsc kh
ln = (ψe − ψw )
rw psc qsc T
or,
à !
πTsc kh (ψe − ψw )
qsc = ³ ´
psc T ln re
rw
The above equation is valid for all conditions and may be used to estimate the
stabilized rate for gas wells under Darcy flow conditions. It requires evaluation
of pseudo-pressures. Pseudo-pressures are easily calculated by numerically inte-
grating P , µ and z data for the gas. An example of such a calculation is given in
Exercise-8.11.
In high rate gas wells flow velocities close to the wellbore may sufficiently high
for turbulent or non-Darcy flow to occur. This introduces an additional pressure
240
drop which depends on the gas rate. The non-Darcy flow pressure drop may be
included by defining an effective skin factor, s0 , as
s0 = s + D|qsc |
where D is the non-Darcy flow constant and s is the Darcy flow skin factor. The
absolute value of rate indicates that there is a positive non-Darcy flow loss for
both production and injection operations. D and s are determined from multi-
rate well pressure test data.
For pressures below about 3000 psia the product µz is approximately constant
and pseudo-pressure, defined as
Z p
p
ψ=2 dp
0 µz
may be written as
2 Zp p2
ψ= pdp =
µ̄z̄ 0 µ̄z̄
where µ̄ and z̄ are evaluated at average flowing conditions.
For pressures above about 3000 psia the product p/µz is approximately constant
and pseudo-pressure, defined as
Z p
p
ψ=2 dp
0 µz
241
may be written as
2p̄ Z p 2p̄
ψ= dp = p
µ̄z̄ 0 µ̄z̄
where µ̄, z̄ and p̄ are evaluated at average flowing conditions.
2πkh (pe − pw )
qsc = h ³ ´ i
µ̄B̄g ln re − 0.75 + s + D|qsc |
rw
With the non-Darcy flow term set to zero (D = 0), this equation is identical to
the equation previously derived for the flow of a slightly compressible fluid.
242
Problem 8.5 - Calculation of gas well rate [GASFLOW.mcd]
Estimate the production rate of a gas well when the average reservoir pressure
is 2723 psia and the flowing wellbore pressure is maintained at 2655 psia. The
following reservoir and fluid properties are known:
k= 5 md
h= 35 ft.
rw = 0.5 ft.
re = 2640 ft.
µ= 0.018 cp
z= 0.87
T = 200o F
s= -0.3
D= 0.015 (MMSCF/day)−1
243
Problem 8.6 - Gas well rate using pseudo-pressures [PSUDOP.mcd]
Estimate the production rate of a gas well when the average reservoir pressure is
2723 psia and the flowing wellbore pressure is maintained at 2655 psia. Reservoir
temperature is 200o F and the gas gravity is 0.7. Use pseudo-pressure and the
pressure-squared method to calculate the gas rate. The following reservoir and
fluid properties are known:
k= 5 md
h= 35 ft.
rw = 0.5 ft.
re = 2640 ft.
T = 200o F
s= -0.3
D= 0.015 (MMSCF/day)−1
GAS PROPERTIES
p µ z
(psia) (cp)
244
Figure 8.19: Pseudo-pressure as a function of pressure
This is an empirical equation which relates flow rate and pressure for gas wells.
The equation is written as,
The constants C and n are determined from flow after flow or conventional back-
pressure tests. The well is flowed at a constant rate (qsc ) until the flowing wellbore
pressure (pw ) has stabilized. The rate is then changed (increased) and the process
repeated. After a number of rate changes (usually four), the well is shutin until
the shutin wellbore has stabilized. This is the average reservoir pressure (p̄R ).
245
Figure 8.20: Gas well deliverability plot
246
Figure 8.22: Interpretation of four point flow-after-flow well deliverability test
A plot of log(p̄2R − p2w ) against log qsc gives a straight line of slope equal to 1/n
and intercept −(1/n) log C. The test and interpretation procedure is illustrated
in the attached figures.
The following flow rate and wellbore pressure data was obtained from a four point
flow-after-flow test on a gas well:
247
Determine the exponent n and the performance coefficient C. Calculate the
Absolute Open Flow (AOF) for the well (the AOF is a commonly used figure-of-
merit for a gas well and corresponds to the well rate at a flowing well pressure of
one atmosphere).
A four point flow-after-flow test produced the following back pressure equation
constants,
n = 0.69
C = 0.01508 MSCF/day-psia2n
(i) Determine the absolute open flow rate (AOF) for the well.
(ii) What would the well flow rate be if the flowing wellbore pressure was main-
tained at 300 psia.
248
Figure 8.23: Horizontal well in a compartmentalized reservoir
Horizontal wells are now routinely used in primary, secondary and tertiary re-
covery operations. The major advantages over conventional vertical wells are in
overcoming:
Reservoir heterogeneity
249
Figure 8.24: Comparison between effective reservoir contact areas for horizontal
and vertical wells
Completion options
250
Figure 8.25: Horizontal wells with multiple transverse fractures play a vital role
in the production of tight gas reservoirs
Liners with partial isolation allow the horizontal section to be divided into
several isolated sections. This allows production control along the well
length and selective stimulation or multiple fracking.
Cemented and perforated liners provide the best completions provided that
care is taken to ensure a good cement job.
Wells are drilled on a pattern to provide adequate drainage of the reservoir. The
area drained by a single well in the pattern is the drainage area for the well. A
vertical well drains a cylindrical volume and a horizontal well drains an ellipsoid
(three-dimensional ellipse). A horizontal well will usually drain a larger area than
a vertical well.
251
Figure 8.26: Completion techeniques for horizontal wells
252
Figure 8.27: Comparison of horizontal and vertical well costs for Prudhoe Bay in
Alaska
the drainage area of a horizontal well may be estimated from that for a vertical
well as shown in the attached figure.
The drainage area for a vertical well may also be approximated as a square of
dimensions 2xe by 2ye where xe = ye
Av = 4xe
or s
Av
xe = ye =
4
A horizontal well can be viewed as a number of vertical wells drilled on a line
and completed in a limited pay thickness. Under similar operating conditions,
the drainage area of a horizontal well may be estimated from that for a vertical
well as shown in the attached figure.
Ah = 2ye L + Av
where L is the length of the horizontal section. The effective drainage radius of
a horizontal well is q
reh = Ah /π
As a rule of thumb, a 1000 ft horizontal well will drain twice the area of a vertical
well and a 2000 ft horizontal well will drain three times the area of a vertical well.
253
Figure 8.28: Drainage areas for horizontal and vertical wells
254
Figure 8.29: Drainage areas for horizontal wells
255
Areally anisotropic reservoir - kx < ky
∂2p ∂2p
kx + ky =0
∂x2 ∂y 2
For an isotropic reservoir, kx = ky = kh , where k−h is the horizontal permeability,
we can write " #
∂2p ∂2p
kh + =0
∂x2 ∂y 2
For an anisotropic
q reservoir we multiply and divide the conservation equation
throughout by kx ky
v s
q u
u kx ∂ 2 p ky ∂ 2
p
kx ky t 2
+ 2
=0
ky ∂x kx ∂y
or " #
q ∂ 2 p ky ∂ 2 p
kx ky + =0
∂x2 kx ∂y 2
This equation may be written as
" #
q ∂2p ∂ 2p
kx ky + =0
∂x2 ∂Y 2
where s
ky
y=Y
kx
Comparing this equation with that for the isotropic system,
" #
∂2p ∂2p
kh + =0
∂x2 ∂y 2
256
Figure 8.30: Drainage areas for horizontal wells in fractured or anisotropic reser-
voirs
257
Figure 8.31: Drainage areas for vertical and horizontal wells in anisotropic reser-
voirs
If ky > kx , s
ky
ye = xe
kx
and the drainage area for a vertical well is
Ah = 4ye xe
The above analysis shows that it is difficult to drain a reservoir in the low per-
meability direction using vertical wells.
258
Example 8.7 - Drainage area for horizontal wells in an isotropic reser-
voir [HORWELL.mcd]
259
Figure 8.32: Complexity of flow regimes for horizontal wells. a-early time radial
flow, b-early time linear flow, c-late time radial flow, d-late time linear flow
260
Figure 8.33: Approximating three-dimensional steady-state flow in horizontal
wells with two two-dimensional solutions
Numerous equations have been developed for steady-state flow of horizontal wells.
The differences between the various equations result from the differences in solu-
tion techniques employed and the details of the assumptions made in developing
the solution. The differences are generally small.
For a horizontal well completed in the middle of sand of thickness, h, with con-
stant pressure boundary conditions at the drainage area boundary,
qh 2πkh h/(µB)
Jh = = ∙ √ ¸ ³ ´ ³ ´
∆p a+ a2 −(L/2)2 h h
ln L/2
+ L
ln 2rw
261
Figure 8.34: Productivity ratio Jh /Jv for horizontal wells in isotropic reservoirs
where a is half the major axis of the drainage area ellipse defined as,
s 0.5
µ ¶4
L 2reh
a = 0.5 + 0.25 +
2 L
s
Ah
reh =
π
for L > h and (L/2) < 0.9reh .
The above equation shows that as reservoir thickness, h, increases, the effective-
ness of the horizontal well, Jh , decreases. Horizontal wells are most effective in
thin reservoirs.
2πkh h/(µB)
Jh =
ln (4reh /L) + (h/L) ln (h/2πrw )
This equation gives results very similar to those using the Joshi equation. In the
limit L >> h, the second term in the denominator of the equation is negligible
and the result can be rewritten as
2πkh h/(µB)
Jh =
ln (reh /[L/4])
262
Comparing this equation with the corresponding equation for a vertical well shows
that in the limit L >> h, a horizontal well is equivalent to a vertical well with
0
an effective wellbore radius rw = L/4 (a highly stimulated vertical well). We will
later show that the above equation is identical to that for a vertical well with an
infinite-conductivity vertical fracture of length L.
Isotropic reservoirs - kv 6= kh
2πkh h/(µB)
Jh = ∙ √ ¸ ³ ´ ³ ´
a+ a2 −(L/2)2 βh βh
ln L/2
+ L
ln 2rw
where s
kh
β=
kv
263
Figure 8.35: Productivity ratio Jh /Jv for horizontal wells in anisotropic reservoirs
The above equations are for the case where the horizontal well is centered with
respect to the sand in which the well is completed. A schematic of an off-centered
horizontal well is shown in the attached figure. We define well eccentricity, δ, as
h/2 − zw
δ=
h/2
2πkh h/(µB)
Jh = ∙ √ ¸ ³ ´ ³ ´
a+ a2 −(L/2)2 βh βh
ln L/2
+ L
ln 2rw
[1 + δ2 ]
which is valid for L > βh, δ < h/2 and L < 1.8reh .
For long horizontal wells, (L >> h), eccentricity has little effect and the well
can be located anywhere in the vertical plane without significant loss in produc-
tivity. This is strictly true only for bound reservoirs where the top and bottom
boundaries are closed ie., there is no bottom water or top gas.
264
Figure 8.36: Horizontal well accentricity
265
Problem 8.9 - Horizontal well productivities I [HORWELL.mcd]
A 1000 ft. horizontal well is drilled through the centre of a 50 ft sand on a 160
acre spacing. Other data reservoir and fluid parameters are;
kh =50 md
µ =0.4 cp
rw =0.33 ft
B =1.35 RB/STB
(i) Compare the horizontal well productivities for kv /kh of 0.01, 0.1, 0.5 and 1.
(ii) For kv /kh =0.1 compare the horizontal well productivities if the well is lo-
cated at distances of 1 ft, 10 ft and 20 ft from the base of the sand.
[Answer: Joshi equation (i) 7.2, 13.3, 16.1, 16.9 STB/day-psi (ii) 12.7, 13.0, 13.2
STB/day-psi ]
A 1000 ft. horizontal well is drilled in a reservoir on a 160 acre spacing. The
horizontal permeability averages 200 md and the vertical permeability averages
20 md. Other reservoir and fluid parameters are;
µ =0.2 cp
rw =0.33 ft
B =1.35 RB/STB
What is the improvement in productivity which may be expected over that for a
vertical well if the sand thickness is,?
(ii) 20 ft.
266
Effect of Formation Damage on Horizontal Well Productivity
As in the case of vertical wells, formation damage can have a severe effect on
horizontal well productivity. Consider the case of a horizontal well completed at
the center of a homogeneous anisotropic sand. Renard and Dupuy (SPE19414,
1990) developed the following equation for the productivity index,
2πkh h/(µB)
Jh = ³ ´ ³ ´ ³ ´
−1 2a βh βh
cosh L
+ L
ln (1+β)πrw
where a is half the major axis of the drainage area ellipse as previously defined.
The above equation and the previously discussed equation developed by Joshi
produce similar estimates for horizontal well productivity.
2πkh h/(µB)
Jh,d = ³ ´ ³ ´ ³ ´
cosh−1 2a
L
+ βh
L
ln βh
(1+β)πrw
+ sh
where sh is the horizontal well skin factor which must be determined from well
tests.
The ratio of productivities for a damaged and undamaged horizontal well is there-
fore, ³ ´ ³ ´ ³ ´
Jhd cosh−1 2a L
+ βh
L
ln βh
(1+β)πrw
= ³ ´ ³ ´ ³ ´
Jh −1 2a βh βh
cosh L
+ L
ln (1+β)πrw
+ sh
or
Jhd B
=
Jh B + sh
where
µ ¶ Ã ! Ã !
−1 2a βh βh
B = cosh + ln
L L (1 + β)πrw
267
Figure 8.38: Comparison between formation damage for horizonral and vertical
wells
268