Professional Documents
Culture Documents
IPC-PT/MV11 Series,
IPC-PT/LS11 Series,
HPC-HMV11 Series,
HPC-HLS11 Series
Hardware Manual
CONTEC CO.,LTD.
Copyright
Copyright 2006 CONTEC CO., LTD. ALL RIGHTS RESERVED.
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this
document.
The information in this document is subject to change without notice.
All relevant issues have been considered in the preparation of this document. Should you notice an
omission or any questionable item in this document, please feel free to notify
CONTEC CO., LTD.
Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may
appear in this document or for results obtained by the user as a result of using this product.
Trademarks
MS, Microsoft and Windows are trademarks of Microsoft Corporation. Other brand and product
names are trademarks of their respective holder.
Trademarks .............................................................................................................................................. i
Table of Contents.................................................................................................................................... ii
1. INTRODUCTION 1
Features .............................................................................................................................................1
Liability....................................................................................................................................................2
2. OVERVIEW 7
Specifications...........................................................................................................................................7
Physical Dimensions..............................................................................................................................10
4. HARDWARE SETUP 25
Installation Requirements .............................................................................................................. 25
Card removal prevention fitting .................................................................................................... 26
Back light exchange ....................................................................................................................... 26
Attaching the Fitting Used to Attach to This Product .................................................................. 27
Removing the PCI expansion unit connector cover...................................................................... 29
Attaching the simple stand............................................................................................................. 30
EMC measure ................................................................................................................................. 30
5. LIST OF OPTIONS 31
1. Introduction
This product is a panel mount computer based on the SH-4 CPU, integrating a TFT color LCD display
with a touch screen. As the unit has assorted interfaces including the USB, PC Card, 100BASE-TX,
and RS-232C connectors, it can be used widely as a general-purpose terminal for embedded applications.
Under Windows CE .NET 4.2 loaded from Flash ROM along with user programs, the unit is
implemented as diskless hardware without the need for a shutdown procedure.
This product employs an aluminum front panel, resulting in shorter outside dimensions and lighter
weight than the conventional model. It also employs a simplified structure that makes installation
easier than the conventional model.
Features
- Slim, compact design with a lightweight aluminum front panel (Embedded portion 46/49 mm)
- Rear fitting to easily fix the unit in the installation hole
- LCD arm (VESA compliant 75 mm type) available for installation
- 128MB (SDRAM) system memory standard
- 128 MB of internal, erasable programmable Flash ROM available as a user area, allowing user
programs to be added and deleted.
- Standard with two channels of serial port (one of which can be set for the RS-422A/485)
- Standard with a USB port, PC Card slot, 100BASE-TX LAN connector, and general-purpose
isolated digital I/O ports (three for each)
- Standard with stereo sound subsystem (external speaker output) and I/F driver
- XIP & memory loading boot function, enabling high-speed startup/operation as fast as approx. 10
seconds
- “CONTEC Manager” for system development support (scheduling, FTP server, auto-run, etc.)
- Front part is water-proof and dust-proof structure of IP65 performance
- [IPC-PAC(PCI)-C1], an optional expansion unit available to add one short-size PCI board
Customer Support
CONTEC provides the following support services for you to use CONTEC products more efficiently
and comfortably.
Web Site
Japanese http://www.contec.co.jp/
English http://www.contec.com/
Chinese http://www.contec.com.cn/
Free download
You can download updated driver software and differential files as well as sample programs available in
several languages.
Repair will be free of charge only when this device is returned freight prepaid with a copy of the
original invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office,
from which it was purchased.
This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and
original products. The warranty is not applicable if the device has been tampered with or damaged
through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in
which case repairs will be considered beyond the warranty policy.
Liability
The obligation of the warrantor is solely to repair or replace the product. In no event will the
warrantor be liable for any incidental or consequential damages due to such defect or consequences that
arise from inexperienced usage, misuse, or malfunction of this device.
Safety Precautions
Understand the following definitions and precautions to use the product safely.
Safety Information
This document provides safety information using the following symbols to prevent accidents resulting
in injury or death and the destruction of equipment and resources. Understand the meanings of these
labels to operate the equipment safely.
Handling Precautions
WARNING
- Do not use this product in the presence of flammable or corrosive gases. This may lead to
explosion, fire, or damage to equipment.
- In the event of smoke, or abnormal smells or sounds, immediately turn OFF the power to this
device, disconnect the plug from the power outlet, and contact the manufacturer. Continued use
could lead to fire or electrical shock.
- Because of the danger of electrical shock or fire, do not contact this product (Other than the front
touch panel) while electrical current is present.
- Never touch this product or connectors with wet hands. This can cause electrical shock.
- Do not allow this product to come into contact with foreign substances (metal particles, flammable
substances, liquids, etc.) This can cause fire or electrical shock.
- Do not place this product in an unstable location or use incomplete mountings. This may cause
this product to fall.
- This product must be operated at the specified voltage. Use of any other voltage level may cause
fire or electrical shock.
- This product must be properly grounded.
- When attaching or removing extension units, always be sure to unplug the power cable from the
electrical outlet.
- Users should never disassemble or modify this product, or exchange components. This can cause
fire or electrical shock. In addition, the manufacturer is unable to repair products that have been
modified by the user.
- Procedures that could result in serious injury or loss of human life should never be performed from
a touch panel. Use system design methods that can guard against input errors.
CAUTION
- Do not use or store the product in a location such as extremely high or low temperature, rapid
temperature changes, and the place which receives a strong ultraviolet ray.
Example: - Exposure to direct sun
- In the vicinity of a heat source
- Do not use this product in extremely humid or dusty locations.
It is extremely dangerous to use the product with its interior penetrated by water or any other fluid
or conductive dust. If the product must be used in such an environment, install it on a dust-proof
control panel, for example.
- Avoid using or storing this product in locations subject to shock or vibration.
- Do not use this product in the vicinity of products that generate strong magnetic force or noise.
Such products will cause this product to malfunction.
- Do not use or store this product in the presence of chemicals.
- To clean this product, wipe it gently with a soft cloth dampened with either water or mild detergent.
Do not use chemicals or a volatile solvent, such as benzene or thinner, to prevent pealing or
discoloration of the paint.
- Do not use any sharp-pointed object such as a mechanical pencil to touch the touch panel. Doing
so may scratch the touch panel, resulting in malfunctions.
- Do not subject the touch panel to shock as doing so may break it.
- When the surface or frame of the touch panel has become dirty, wipe it with neutral detergent. Do
not wipe the touch panel with thinner, alcohol, ammonia, or a strong chlorinated solvent. Use a
protective sheet (available as an option) if the touch panel is used where it can easily collect dust
and dirt.
- It is a characteristic of analog touch panels that their resistance may vary with changes to the
ambient environment (temperature and humidity) and with their own aging, resulting in the
deviation of the detection point. If this is the case, calibrate the touch panel again to re-set
calibration data.
- Burn-in on TFT Display
"Burn-in" may occur if the same display is retained for a long time. Avoid this by periodically
switching the display so that the same display is not maintained for a long time.
* Burn-In : Phenomenon characterized by a TFT display as a result of long-time display of the
same screen where a shadow-like trace persists because electric charge remains in the
LCD element even after the patterns are changed.
- Life expectancy of components
(1)Battery : A lithium-ion primary battery is used to back up the internal clock/calendar and
CMOS RAM. The non-energized backup time at 25°C is 10 years or more.
NOTE
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference at his own expense.
WARNING TO USER
Change or modifications not expressly approved the manufacturer can void the user's authority to
operate this equipment.
2. Overview
Specifications
Functional Specifications
LCD type LCD type 10.4-inch TFT color LCD (640 x 480) 12.1-inch TFT color LCD (800 x 600)
Number of colors 65536
Touch panel Resolution 4096 x 4096 (emulated in 640×480 mode) 4096 x 4096 (emulated in 800 x 600 mode)
Detection method Analog resistive
CPU Type SH4 HD6417751RBP 240MHz
Internal cache Data: 16KB, Instruction: 32KB
Clock frequency 240MHz
Memory Flash memory 128MB
(NFDISK)
System memory 128MB SDRAM
OS loading 32MB
Flash memory
COM port RS-232C(2ch) COM1 (16550, 9-pin D-SUB)
COM2 (16550, 9-pin D-SUB, Settable for RS-422/485)
Baud rate : 50 - 115200bps
LAN 10BASE-T/100 BASE-TX 1ch, NS DP83816A
PS/2 None
PC card slots PCMCIA Type II x 2, or TypeIII x 1
General-purpose I/O Optocoupler isolated inputs and outputs : 3 channels each
USB 2ch (USB 1.1)
Output terminals for external φ3.5 Stereo mini jack Full-scale output level 1.0Vrms (Typ.)
speakers
Front switch & Power LED Front switch input : 3 points; Front Power LED : 3-color display
Video input terminator BNC connector input impedance 75Ω
Input power supply <IPC-PT/MV11AC> <IPC-PT/LS11AC>
100VAC 100VAC
Input range : 100V - 240VAC 50VA Input range : 100V - 240VAC 50VA
<IPC-PT/MV11DC1> <IPC-PT/LS11DC1>
+12VDC +12VDC
Input range : 12V±5% 2.5A(Max.) Input range : 12V±5% 2.5A(Max.)
<IPC-PT/MV11DC2> <IPC-PT/LS11DC2>
+24VDC (isolation) +24VDC (isolation)
Input range : 20V - 28VDC 2A(Max.) Input range : 20V - 28VDC 2A(Max.)
Power supply 100VAC input type: 50VA (Max.)
12VDC input type: 12VDC±5% 2.5A(Max.)
24VDC input type: 24VDC ±20% 2A(Max.)
Outside dimensions (mm) 305(W) x 240(H) x 51(D) 316(W) x 256(H) x 54(D)
Panel cut dimensions (mm) 292(W) x 227(H) 303(W) x 243(H)
Weight About 3.3kg *1 About 3.5kg *1
*1 Does not include cables, optional accessories, and screws, etc.
Ambient specifications
Operating temperature 0 - 50ºC
Storage temperature -10 - 60ºC
Humidity 20 - 85%RH (No condensation)
Floating dust particles Not to be excessive
Corrosive gases None
Line-noise Line noise AC line : ±2kV (IPC-PT/xx11AC series)
resistance Signal line : ±1kV (EN61000-4-4 Level3, IEC1000-4-4 Level 3)
Static Contact discharge / ±4kV (EN61000-4-2 Level 2, IEC1000-4-2 Level 2)
electricity Atmospheric discharge / ±8kV (EN61000-4-2 Level 3, IEC1000-4-2 Level 3)
resistance
Vibration Anti-shaking 10 - 57Hz/semi-amplitude 0.15mm
resistance One cycle (10-150-10 Hz) of 1 oct/min test at 19.6 m/s2 (2G) between 57 and
150 Hz 5 times in three (X/Y/Z) directions (40 minutes each)
(JIS C0040-compliant, IEC68-2-6-compliant)
(Option IPC-PAC(PCI)-C1 unconnected)
Impact resistance Tested with 11-ms half-sine wave at 98 m/s2 (10G) three times in each of
tree (X/Y/Z) directions
(JIS C0041-compliant, IEC68-2-27-compliant)
Ground Class D grounding (previous class 3 grounding)
Water-proof and dust-proof IP65, front
Table 2.3. Power Supply Installation Environmental Conditions for AC Powered Models
(IPC-PT/xx11AC series)
Item Specification
Power supply specifications
Allowable instantaneous Less than 17ms (Mean value with ACIN 100 V, Io = 100%)
Power outage 2.0kVAC (between input and FG), 10 mA for 1 minute
Dielectric strength 50MΩ (500VDC)
1 - 10mS
11.4V 19.2V
18.0V
Time Time
Z Measurement direction
( θ = 0o )
Left
( φ = -90o ) θ
Top
( φ = 180o )
X φ Module
Bottom
( φ = 0o )
Right
( φ = 90o )
Y
Physical Dimensions
IPC-PT/MV11 series
51 305
75 216.2
5 46
87.7
240
226
226
U SB
ACT
U TP
LNK
75
75.7
98.3
CO M1
62
C OM2
F1 F2 F3 POWER
46 5
4-M4 TAP 82.5
(Maximum tapping 51
291
length:10mm)
48 50
30
16
(17.6)
[mm]
16
316
54
75 251
5 49
96.75
242
242
256
USB
ACT
UTP
75
LNK
92.75
99.2
COM1
COM2
70
F1 F2 F3 POWER
4-M4 TAP 49 5
82.5
(Maximum tapping 302 54
length:10mm) 48 55.5
30
16
19
[mm]
Component Locations
Functional switch
F1,F2,F3
POWER LED
F1 F2 F3 POW ER
PCMCIA
PCMCIA
I/O
I/O
SOUND
SPK
RESET
RST
USB
USB
ACT
LAN
UTP
LNK
COM1
COM1
COM2
COM2
Connector cover
Power input terminal for the PCI extension unit
* Refer to the software manual for the function switches and POWER LED.
1 5
No.4-40UNC
Inch screw
6 9
6 9
CAUTION
For TxD, RxD, and RTS, RS-422A/485 pin assignment has even-numbered pins for positive and
odd-numbered ones for negative. For CTS, however, even-numbered and odd-numbered pins are
assigned for negative and positive, respectively, in contrast with other signals. This is not a
description error.
1 12
B
C
A
- RS-422A/485 setting
1 12
B
C
A
Setting ON ON
procedure
(SW4) 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
* For SW4’s bits 1 - 4 and 6 - 8 when RS-422A/485 is set, see “COM2 RS-422A/RS-485 data transmission mode
setting” below.
Setting procedure
Table 3.5. Data transmission mode setting
Full duplex [Full]
Half duplex [Half] RTS/CTS self-loop RTS/CTS connection to
remote device
Setting ON ON ON
procedure
(SW4)
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
Description Only TxD is enabled as a If the connected product has Used with the unit connected
data line. The no RTS and CTS signals, the to the RTS and CTS signals
transmission or reception CTS signal becomes active by of the connected product.
mode can be selected by making the RTS signal of
the RTS signal from this this product active.
product.
CAUTION
Do not set bits 7 and 8 of each switch to both ON.
Doing so may cause this product to malfunction.
Connection Procedure
TX_enable
COM2
TXD TXD+ 4
TXD- 5
RXD+ 8
RXD
RXD- 9
RX_enable
TXD- 5
RXD+ 8
RXD
RXD- 9
RX_enable
Individual bits correspond to different signal lines; bits 1 to 4 serve for CTS, RTS, RxD, and TxD,
respectively.
Setting method
To set the terminal to a resistor other than 100Ω, set the terminator setting switch to OFF and insert an
external terminator.
Table 3.6. Terminator Settings
Insert terminator Do not insert terminator
[Term ON] [Term OFF]
ON ON
Setting method
(SW4) 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
(A) or (D) below (B) or (C) below
(either end of signal line) (other than end of signal line)
Terminator Terminator
Illustrated below are the peripheral circuits for the data transmission mode setting and terminator setting
switches.
1
ST16C550 SW4 Terminator
equivalent 1/2W 100Ω
TxD+
SOUT
TxD-
Vcc
47kΩ
6.2kΩ
RxD+
SIN
RxD-
6.2kΩ
47kΩ
Vcc
CTS 47kΩ
6.2kΩ
CTS+
CTS-
6.2kΩ
47kΩ
RTS+
RTS
RTS-
DCD
DTR
DSR
RI
Ethernet (UTP)
Table 3.7. Ethernet connector (RJ-45)
Connector RJ-45
1 8
LINK ACT
LED Indicators
- LINK (Green)
Indicates the LINK status.
- ACT (Orange)
Goes on to indicate that data is being transmitted/received.
PCMCIA (PCMCIA)
PCMCIA compliant card slots are provided ××1 size.
Slot 1
Slot 2
PCMCIA Card
+5V 250mA/Slot
+3.3V 250mA/Slot
+12V Not supplied.
USB port
There are two channels of interfaces of USB.
1 4
↓ Front(LCD) side
Pin No. Signal Remarks
1 PI_PCOM General-purpose input
(plus common)
2 PI(0) General-purpose Input 0
3 PI(1) General-purpose Input 1
4 PI(2) General-purpose Input 2
5 P_PO(0) General-purpose Output 0+
6 N_PO(0) General-purpose Output 0-
7 P_PO(1) General-purpose Output 1+
8 N_PO(1) General-purpose Output 1-
9 P_PO(2) General-purpose Output 2+
10 N_PO(2) General-purpose Output 2-
Connector : MC1,5/10-GF-3,5(PHOENIX CONTACT)
Cable connector : MC1,5/10-STF-3,5(PHOENIX CONTACT)
Specifications
[Input section]
- Input specification : Optocoupler isolated current drive input
- Input resistance : 3kΩ
- Number of input signals :3
- Input protection circuit : Reverse-connection protection diode provided
- Input response time : Within 100μsec
- External circuit power supply : 12V - 24VDC(±10%)
[Output section]
- Output specification : Optocoupler isolated open-collector output
- Output rating : 30VDC, 100mA max.
- No. of output signals :3
- Output response time : Within 300μsec
External Connection
PI_PCOM
3kΩ
10kΩ 1/2W
External power supply
(12V - 24VDC)
Input
PI(0) - PI(2) contact
I/O connector
(External circuit)
Load
P_PO(0) - P_PO(2) External power supply
330Ω PC357 (Max. 30VDC)
2SD780A
4.7kΩ
N_PO(0) - N_PO(2)
I/O connector
N L
GND +12V
GND +24V
Figure 3.14. Power input terminal <+24 VDC isolated input type >
CAUTION
All the terminals are identically shaped. Be careful not to connect power at wrong In voltage, or
the unit may cause a fault.
1pin
GND
2pin
R Analog signal
3pin
L Analog signal
Touch Panel
This product is equipped with an analog touch panel that enables keyboard-less, mouse-less operations.
Refer to the software manual for details on how to use the touch panel.
1 2 3 4 5 6 7 8
CAUTION
Use this setting for normal operation.
1 2 3 4
WARNING
Operating a connector or jumper on the internal CPU board, which is not covered by this manual,
can cause the unit to malfunction or develop operational problems. Never touch any of those
on-board connectors and jumpers.
4. Hardware Setup
Installation Requirements
In this product, the ambient temperature is decided from the multiple measurement points as shown
below.
When making use of the product, the air current should be adjusted to prevent that all the temperatures
measured at the measurement points exceed the specified temperature.
PCMCIA Card
Figure 4.3. Attaching the Fitting Used to Attach to This Product <1/2>
(2) Hold the attachment from the inside of the panel.
Panel
Fitting
This product
Figure 4.3. Attaching the Fitting Used to Attach to This Product <2/2>
R1 or less
+1
227 -0
R1 or less
+1
243 -0
CAUTION
Use a panel with a thickness in the range 1.6 - 7mm.
Figure 4.6. Removing the connector cover for the PCI extension unit
CAUTION
Using the simple stand involves the risk of letting the unit fall down.
You should therefore use the stand as a simple gadget with meticulous care not to let the unit fall.
EMC measure
To take a measure for EMC, fit the following ferrite core to the speaker cable, serial connection cable
(when using COM1 - COM2).
At the time of speaker cable wearing, it is 2 turn necessity.
5. List of Options
Screen protective sheets
- IPC-CV : Screen protective sheets for 10.4inch (10 sheets)
- IPC-CV12 : Screen protective sheets for 12.1inch (10 sheets)
Stand
- IPC-SND-03 : Desk stand
Cable
- IPC-ACCODE3 : AC power cable (2 m, 125 VAC supported)
Manual (The latest user’s manual is available from the CONTEC homepage.)
- IPC-PT/11SH4-HMJ : Hardware manual (Japanese) for IPC-PT/MV11, IPC-PT/LS11 series
- IPC-SH4CE4-SMJ : Software manual (Japanese) for IPC-PT/MV series, IPC-PT/LS series
- IPC-SH4CE4-SME : Software manual (English) for IPC-PT/MV series, IPC-PT/LS series