Professional Documents
Culture Documents
OPERATION MANUAL
Please carefully read this manual before you start, then operate by following the correct
procedures in a proper manner.
Please keep this manual with the product after you have read it.
When lending or transferring this product, ensure that the instruction manual accompanies
the product.
Some machine parts are subject to design changes to increase machine performance and
safety. If there is any design change, please note that the contents and some of the
illustrations in this manual might not correspond to the product.
We would welcome any comments regarding any information in the instruction manual
which is considered incomplete or ambiguous.
The symbol " " indicates that the instruction following it is very important for the safety of the
operations. Please strictly observe such instructions.
WARNING Indicates a possibility of death and of serious accident, if you do not pay
close attention during handling.
There is also a possibility of death and of serious accident, even when the instructions only come
with the " CAUTION" warning. Please strictly observe correct handling procedures.
GDM HEAD
CONTENTS
COMPONENT NAMES 1
PREACAUTIONS ON HANDLING
AUGER HEAD
Operation (General) 5
Auger Head 6
ATTACHMENTS &
CONSUMABLE ITEMS 14
PARTS ORDER 15
E_GDM-0(IMGD000-3)
COMPONENT NAMES
Auger Head (PA10, PA16)
(Mass:About 87 kg)
Part
Name Code Quantity
Number
1 Pilot Bit 02085545 1
2 Outer Bit 02073882 8
3 Pilot Bit Pin 02073967 1
4 O-ring 02065565 1
5 Cap 02084073 1
6 Zooming blade 02105224 2
7 Socket of Zooming blade 02065378 2
8 Bolt of Zooming blade 02064457 2
Part
Name Code Quantity
Number
1 Pilot Bit 02085545 1
2 Outer Bit 02073882 6
3 Pilot Bit Pin 02073967 1
4 O-ring 02065565 1
5 Cap 02084073 1
1
COMPONENT NAMES
Auger Head (PA10, PA16)
(Mass:About 53 kg)
Part
Name Code Quantity
Number
1 Pilot Bit 02085545 1
2 Outer Bit 02073882 12
3 Pilot Bit Pin 02073967 1
4 O-ring 02065565 1
5 Cap 02084073 1
Part
Name Code Quantity
Number
1 Pilot Bit 02085545 1
2 Outer Bit 02073882 13
3 Pilot Bit Pin 02073967 1
4 O-ring 02065565 1
5 Cap 02084073 1
2
COMPONENT NAMES
Auger Head (PA10, PA16 Option)
(Mass:About 66 kg)
Part
Name Code Quantity
Number
1 Pilot Bit 02085545 1
2 Outer Bit 02073882 16
3 Pilot Bit Pin 02073967 1
4 O-ring 02065565 1
5 Cap 02084073 1
Part
Name Code Quantity
Number
1 Pilot Bit 02085545 1
2 Outer Bit 02073882 17
3 Pilot Bit Pin 02073967 1
4 O-ring 02065565 1
5 Cap 02084073 1
3
COMPONENT NAMES
Auger Head (PA11)
(Mass:About 150 kg)
Part
Name Code Quantity
Number
1 Pilot Bit 02085545 1
2 Outer Bit 02073882 12
3 Pilot Bit Pin 02073967 1
4 O-ring 02068088 1
5 Cap 02084073 1
6 Zooming blade 02105228 2
7 Socket of Zooming blade 02067943 2
8 Bolt of Zooming blade 02068077 2
Part
Name Code Quantity
Number
1 Pilot Bit 02085545 1
2 Outer Bit 02073882 14
3 Pilot Bit Pin 02073967 1
4 O-ring 02068088 1
5 Cap 02084073 1
6 Zooming blade 02080150 2
7 Socket of Zooming blade 02067943 2
8 Bolt of Zooming blade 02068077 2
4
PREACAUTIONS ON HANDLING AUGER HEAD
WARNING
Preparation
1. Never operate the machine without the proper
training.
PLEU0007
PLEU0007
5
PREACAUTIONS ON HANDLING AUGER HEAD
WARNING
Operation
1. When inspecting the auger head installed to the
auger screw, make sure to shut down the Silent
Piler and turn OFF the power of the radio control
transmitter or the cable controller.
2. When replacing the bit on the auger head which is
installed to the auger screw, make sure to turn
OFF the power of the radio control transmitter or
the cable controller and stop the engine of the
power unit.
3. When replacing the bit of the auger head, make
sure your surroundings are safe. When hammering
out the bit, be careful so that the sprung-out bid
does not hit directly a person or an object, or does
not scatter the surrounding objects by hitting them.
4. When repairing the auger head, make sure to
remove the auger head from the auger screw. Set the
5. When removing/installing the auger head in the casing
lock
condition where the Pile Auger is set in the Silent securely.
Piler, support the Pile Auger with a crane. At the
same time, make sure to lock the Pile Auger using
the casing lock (or casing lock pin) to prevent the
Pile Auger from coming down.
6. Do not use the deformed joint pin for installing the
auger head. After driving in the joint pin securely,
remove soil, sand, etc. and tighten the joint lock
bolt to the specified torque.
6
INSPECTION & MAINTENANCE
Inspection of Auger Head
WARNING
When inspecting the auger head installed to the auger screw, make sure to turn OFF the
power of the radio control transmitter or the cable controller.
WARNING
Do not put your hand or foot in the space between the ground and the auger head or to the
auger screw.
5 mm or more
5 mm or more
Less than φ46 mm
0 mm or less
7
INSPECTION & MAINTENANCE
Inspection of Auger Head
If the carbide overlay on the blade
or holder of the auger head has Integrated blade type Holder type
been worn out and the base
material has been exposed, make Holder
repairs in good time.
WARNING
When inspecting the auger
head, make sure to remove the
auger head from the auger
screw.
CAUTION
If you continue to use the auger
head in the condition where the
carbide overlay at the most outer
portion of the auger head main
body is worn out, abrasion at the Entry of the bit Carbide overlay
entry of the bit increases. As a
result, it will be needed to cut the
blade main body or holder and
Need
make repairs.
Repair
Abrasion of carbide
overlay
<For Integrated Blade Type> Exposure of base
material
If the entry of the bit at the most
outer portion of the auger head
main body is damaged significantly,
cut the most outer portion of the
blade and make repairs.
Cannot
Use
Significant
damage
Crack
2 mm or less
Same as the case of
holder abrasion
Detail of Cross-section A
8
INSPECTION & MAINTENANCE
Inspection of Auger Head
If the carbide overlay on the blade
or holder of the auger head has Cannot
been worn out and the base Use
material has been exposed, make
repairs in good time.
WARNING
When inspecting the auger
head, make sure to remove the
auger head from the auger
screw.
Significant
damage
CAUTION
<For Holder Type>
If the holder of the auger head Cannot
main body is damaged Use
significantly, cut the holder and Significant
make repairs. damage
Damage of the
<For Integrated Blade Type> entry of the bit at
the portion except
If the entry of the bit at the portion the most outer
except the most outer portion of portion
the auger head main body is Crack
damaged significantly, cut the
whole of the blade and make
repairs.
9
INSPECTION & MAINTENANCE
Inspection of Auger Head
WARNING
When inspecting the
auger head, make
sure to remove the Bracket
auger head from the
Bolt
auger screw.
Zooming blade
If there is any
deformation or abrasion
on the zooming blade or
bracket installed to
auger head as shown in Socket
the figure, replace with
a new one.
Zooming blade
Not circle
Significant
damage
Warpage
Model : PA10,16
36→ 38 or more
Model : PA11
41→ 43 or more
10
INSPECTION & MAINTENANCE
Inspection of Auger Head
WARNING
When inspecting the Model : PA10,16
auger head, make
sure to remove the Socket
auger head from the Significant
auger screw. damage Deformation of tap
If there is any
deformation or abrasion
on the bolt or socket
installed to auger head
as shown in the figure,
replace with a new one.
φ46 45 or less
8→5 or less
Bolt
Significant
damage Deformation of tap
8→5 or less
Model : PA11,12
Socket
Significant
damage Deformation of tap
φ56→55 or less
10→7 or less
Bolt
Significant
damage Deformation of tap
8→5 or less
11
INSPECTION & MAINTENANCE
Replacing the Bit
WARNING
When replacing the bit on the
auger head which is installed to Hammer
the auger screw, make sure to
turn OFF the power of the radio Bit installation/
control transmitter or the cable Hammer
Pilot bit pin removal jig
controller and stop the engine
of the power unit.
CAUTION
Remove soil and sand before
installing the replacement bit.
When removing
Bit installation/
Hammer removal jig
12
INSPECTION & MAINTENANCE
Replacing the Zooming blade
WARNING
When replacing the zooming Apply grease
blade on the auger head which
is installed to the auger screw,
make sure to turn OFF the
power of the radio control
transmitter or the cable
controller and stop the engine
of the power unit.
Install the zooming blade and the
socket, then apply the grease to
the threaded part of the bolt, and
tighten the bolt to the specified
torque.
CAUTION
Tighten the bolt to the specified
torque.
Model : PA10,16
About 265N
(About 27kgf)
Bolt : M24
Specified torque : 265N・m
(27kgf・m)
Model : PA11,12
About 600N
(About 61kgf)
Bolt : M30
Specified torque : 600N・m
(61kgf・m)
13
ATTACHMENTS & CONSUMABLE ITEMS
Attachments
Bit Installation/Removal Jig
Model Code
PA10,16 02082860
PA11 02071175
PA12 02071175
Outer Bit
(Code : 02073882)
14
PARTS ORDER
When you place an order of parts or make contact with us about failures, please inform
the nearest Giken distributor, Giken designated factory or Giken office of the model number and
the equipment number stamped on the name plate in addition to the running hours of the
equipment recorded in the hour meter of the power unit.
Name Plate
15