Professional Documents
Culture Documents
Revision: Language:
AH S - K R S - 0 0 - O E A- D A- 0 0 - 0 0 1
A EN
Contents
Chapter No Page
The fast main processor has been incorporated in the back-plate of the device, unlike comparable systems.
Its capacity can be increased individually with plug-in co-processor modules and/or intelligent I/O modules.
These have a direct, very fast bus connection to the main processor. The Saia® PCD3 series is therefore
excellently prepared for the rapidly increasing demands on performance that are to be expected.
RUN
M
STOP T F E E DB
vol vol E M
Interrupt
CPU R
nvol
P
R
O
R
Y TX
Backup
C F O M
inputs nvol nvol M A P User
P
memory
User media User
Date-Time memory
nvol
R register
T timer
Watch-Dog C Counter
F flag
vol volatile
nvol non volatile
P program
RS 485 COM/PGU USB connection for TX text
S-Net/ Ethernet Modem RS 232 programming unit DB data block
MPI TCP/IP “full handshaking”
User memory
1 MByte
Total available user memory can practi-
cally be divided at will into sectors for
program, text and data blocks. This ena-
bles the requirements of any particular
Data blocks (DB)
Program
128 KByte
1 MByte RAM
on board Flash
Backup
Backup
Backup
Backup
(P)
128 KByte
128 KByte
RAM
PDC3 Basic
M3020 M3230
On board Ethernet 10/100 MBit/s M3120 M3330
Number of inputs/outputs ≤ 64 ≤ 1023 1)
Number of I/O module sockets 4 ≤ 64 1)
Extension module holder connector no yes
Interrupt inputs 2 2
On board memory
User memory (RAM) 128 KByte 512 KByte 2)
for program, text/DB
Backup memory (Flash) 128 KByte 512 KByte
File-System memory (Flash) Optionen: ≥ 3 MByte mit PCD3/PCD7.R55xM04,
≤ 2 GByte mit PCD3.R600 & PCD7.R-SD512
8 hours with SuperCap
Data protection
Optional: battery kit PCD3.R010
On Board integral ports
On terminal block
RS 485 for free protocols or ≤ 115.2 kBit/s
Multi Master, Profi-S-Net ≤ 187.5 kBit/
On D-Sub connector
RS 232 –
RS 422/ 485 –
Profibus DP slave, Profi-S-Net –
Contr. Area Network CAN 2.0B –
Profibus DP Master –
Optional
RS 232, RS 485, RS 422, TTY/20 mA, Belimo MP-Bus
1 port PCD3.F1xx only used on I/O slot 0
≤ 8 ports PCD3.F2xx I/O slots 0…3
BACnet modul PCD3.R56x I/O slots 0…3 of PCD3.M3120/.M3330
BACnet card PCD7.R56x Slot M1/M2 of PCD3.M5340/. M5540/ .M6340 & .M6540
Integral with all PCD3.Mxxxx Web- & FTP-server, Watchdog, Real time clock
Programmable via USB 1.1 or Ethernet PG5 starting from version 1.4.100 PG5 staring from version 1.3.100
Processing time ■ bit operation 0.3…1.5 μs
■ word operation 0.9 μs
1024 KByte 2)
System resources
Flags 8 192 × 1 bit, volatile or non-volatile, Timing range 31 bit, unsigned (0…2 147 483 647)
division programmable timing signals, selectable (10 ms to 10 s)
Registers 16 384 × 32 bits, non volatile Texts and DBs 8 192
Indexregisters 17 × 13 bit (1 each per COB and XOB) Date-time (RTC) Time values: s / min / h, week / day of week,
month / day of month, year
Timers/Counters 1600 volatile timers or non-volatile counters, Accuracy better than 1 min/month
division programmable
Counting range 31 bit, unsigned (0…2 147 483 647) Power reserve PCD3.M3xx0: 8 hours
PCD3.M5xx0 and PCD3.M6xx0: 1 to 3 years
Computational Integers: –2 147 483 648…+2 147 483 647
ranges (–231…+231–1)
Floating-point numbers:
±9.223 37 × 1018…±5.421 01 × 10–20
Formats: decimal, binary, BCD,
hexadecimal or floating point
With its fast COLDFIRE processor, expansion to 1023 central I/Os and large memory capacity,
the PCD3.Mxxx0 offer a powerful controller platform for multiprocessor operation and data recording,
date management and data transfer.
PCD3.Mxxx0 have four times the number of registers and up to 5 interfaces built into the base unit.
With add-on modules 8 additional serial ports can be achieved. The operating system supports different
protocols, naturally Saia® S-Bus and field busses, such as Profibus and Ethernet TCP/IP.
The Profibus layer 2 (FDL) based Saia® private control network Profi-S-Net includes special features,
as multiprotocol operation (e.g. DP, MPI and HTTP), multimaster communication, the transmission of
plugins (active slaves) and web access.
PCD3.M5540 with opened cover, Flash Card (optional) and battery module (PCD .M5440 without Ethernet)
PCD3.F2xx in:
Slot 0, Port 100 and 101
Slot 1, Port 110 and 111
PCD3.R600
Slot 2, Port 120 and 121
for SD flash or Slot 3, Port 130 and 131
PCD7.R-SD256
or
PCD7.R-SD512
I /O bus extension
(up to 1023 digital I/Os)
with connectoror cable
Port 2
Port 3 or 10
Port 0
Port 9
RS 485
Ethernet-TCP/IP integrated
USB
RS 485/S-Net
RS 232/PGU
PCD3.M3330 (PCD3.M3020 und PCD3.M3230 without Ethernet, not expandable)
Slot 0, Port 1
PCD3.R600
for SD flash or
PCD7.R-SD256
or
PCD7.R-SD512 I /O bus extension
(up to 1023 digital I/Os)
with connectoror cable
Port 2
Port 9
9 8 7 6 10 9 8 7 6 11 9 8 7 6 6 7 8 9 9 8 7 6
F
0
2
M1 M2 Port 1 RS 232
2
Both modules can
1
or RS 422 be equipped with a
or RS 485 PCD7.F1xx module for
or CL 20 mA an additional serial
F
or MP-Bus interface.
1
2
1
F
1
2
1
Profibus DP /
Profi S-Net /
RS 485 / 422
PGU / RS 232
CAN-Bus
Ethernet
RS 485
USB
Protocols supported
Optional interfaces can be used to run the following When determining the maximum communications
protocols: power per PCD3 system, the following should be
Modem communication with the PCD FBox library taken into account:
HMI editor applications with PCD7.Dxxx text terminals The communications volume is determined by periph-
(only with RS 232 interface) eral devices connected. For example, this is the case
Seriell S Net Belimo MP-Bus if the PCD3 is being used as an S-Bus slave station.
JCI N2 - Bus KNX® S-Mode / EIB If a PCD3 controller is bombarded with heavy tele-
DALI EnOcean gram traffic at high baud rates, there will not be much
Other protocols (drivers from third-party suppli- CPU capacity left for processing the actual applica-
ers) are in the responsibility of the manufacturer tion. The following rules apply here: The use of 8 in-
(e.g. restriction mode only up to 9600 bps). terfaces with 9.6 kbps will take up approx. 50 percent
of CPU capacity. Two interfaces with 57.6 kbps will
Transmission rates supported: also take up approx. 50 percent of CPU capacity. Two
1200, 2400, 4800, 9600, 19200, 38400, 57600,115200 bps. interfaces with 115 kbps will need around 60 percent
of CPU capacity.
PCD3.M5xx0 PCD3.M3xx0
PCD3.M6xx0 PCD3.R55xM04 PCD3.R55xM04 Battery kit
PCD3.R500 PCD3.R56x PCD3.R600 PCD3.R500 PCD3.R56x PCD3.R600 PCD3.R010
M1 M2
5
SE
SE
R
R
$
$
IA
IA
G
G
7
7
RI
RI
TE
TE
"
"
USY
USY
!
!
CT
CT
IV
IV
ITY
ITY
or PCD7.R55xM04
or PCD7.R55xM04
or PCD7.R56x
or PCD7.R56x
PCD7.R500
PCD7.R500
Only ������������������������������������
one module can be used per PCD3 CPU
Note: PCD7.R500 cards can also be fitted into PCD3.F1xx communication interface modules
Flash memory with file system, program- and data-backup, BACnet option
PCD7.R55xM04
PCD7.R551M04 4 MByte flash cards with 3 MByte file system and 1 MByte program backup
PCD7.R560 2 MByte flash cards with BACnet option
PCD7.R561 2 MByte flash cards with BACnet option, 1 MByte file system
and 1 MByte program backup
Pluggable flash modules PCD3.R5xx on any I/O module slots of all PCD3.Mxxx0
PCD3.R550M04 4 MByte flash module with file system (Up to 4 modules can be used per PCD3 PLC.)
PCD3.R551M04 4 MByte flash module with 3 MByte file system and 1 MByte program backup
PCD3.R55xM04
PCD3.R560 2 MByte flash module with BACnet option
PCD3.R56x
PCD3.R561 2 MByte flash module with BACnet option, 1 MByte file system
and 1 MByte program backup
Note: PCD7.R55x cards can also be fitted into PCD3.F1xx communication interface modules
5
SE
R
$
IA
G
7
RIT
E
PCD3 basic module for SD flash memory cards with file system
"
US
Y
!
CTI
VIT
Y
PCD3.R600 Up to 4 modules can be fitted into the CPU I/O slots 0…3
PCD3.R600
PCD7.R-SD256 Saia® SD flash memory card 256 MByte with file system
PCD7.R-SD512 Saia® SD flash memory card 512 MByte with file system
Backup
Program backup into flash memory
PG5 can be used to load an application program
into flash memory. All hardware settings will also FLASH Externe
RAM onboard FLASH
be saved to flash. A flash card has priority over the
on board flash.
Restore
Saia® PCD3.Mxxx0 - high performance, compact, modula www.saia-pcd.com
|
r
Counting, measuring and motion control
PCD3.M5540
Local positioning action controlled via
serial port RS 232, RS 422 or RS 485
M M M
Path detection via direct count input (max. 1 kHz)
Whether the drive is analogue or digital, whether there is a frequency inverter, stepper and servomotors
(DC/BL/AC), whether positioning action takes place centrally in the PCD or locally in an intelligent drive: the
PCD offers an efficient solution for every technology and topology. By close coupling of the PCD and the driving
controller, even complex motion sequences and their associated peripheral control functions can be realized
with the comfort and diagnostic capabilities of PCD programming.
Module / Description Frequency Number of Output Count range / Number Internal cur- I/O
Velocity profile Encoder I/Os/A position of rent draw connector
distance axes )
1
5V )2
type 3)
PCD3.H100 Pulse counter ≤ 20 kHz 3 I 16 bit max. 16 90 mA A or B
up to 20 kHz + 1 O digital (65 535)
PCD3.H210 Motion control module ≤ 19.5 kHz 4 I + 4 O square 24 bit max. 16 85 mA A or B
for stepper motors pulse (16 777 215)
PCD3.H310 Motion control module ≤ 100 kHz 4 I + 1 O analogue 30 bit max. 16 140 mA A or B
for servo drives 24 VDC ±10 V, + 1 sign
(path acquisition, 12 bit bit
up to 100 kHz counting (±1 073 741 824)
frequency)
PCD3.H311
as H310 but with RS 422 5 VDC 6 I + 1 O 160 mA
encoder inputs RS 422
¹) No ..H..-module can be used at I/O base address 240 (conflict with WD at 255).
2
) Max. loading capacity: PCD3.Mxxx0: max. 600 mA, PCD3.T76x: max. 650 mA and PCD3.C200: max. 1500 mA (from HW version C)
3
) Plug-in I/O terminal blocks and cables) are not included with I/O modules. They must be ordered separately (see page 20)
4
) The SSI input is electrical isolated
PCD3.Cxxx can be used for centralized I/O extension on the I/O bus of PCD2-/PCD3 controllers
and/or with PCD3.T76x RIOs for decentralized automation tasks via Profibus or Profi-S-Net.
E E E E B B B A
1 1 1 5 1 1 1 2
1 1 1 0 0 0 0 0
0 0 0 0 0 0 0 0
Profi-S-Net
Profibus
5540 100
Profibus DP slave, 1.5 Mbit/s I/O bus connector PCD3.K010
Extension via Profi-S-Net Up to 1023 centralized digital I/Os
I/O bus
connecting cable
PCD3.K106/K116
Extension to a PCD2.Mxxx
CPU via I/O bus PCD3.C200 PCD3.C100
I/O bus
Slot #16 Slot #17 Slot #18 Slot #19
connecting cable
PCD2.K106
200 100
PCD3.C200 PCD3.C110
Extension via Profibus (PCD2.Mxxx)
or Profi-S-Net (PCD2.M480 only) E110 B100 H110 H210 A200 A220
I/O404
EnM
CCO
I435
PUL
O451
0
O467
O468
0
I389 I/O405 TCO DIR O469
Slot #24 Slot #25 Slot #26 Slot #27 Slot #28 Slot #29
#
PCD3.T 76x PCD3.C110
E E W E E A
1 6 3 1 1 4
6 1 1 1 6 6
5 0 5 0 0 0
? #
Up to 15 module holders PCD3.Cxxx can be attached to the PCD3.Mxxx0 (except M3x20). Thus allows the user
to connect up to 64 I/O-modules or 1023 digital I/O points. Every base unit has room for 4 I/O-modules.
PCD3.C200 module holder with connecting terminals for 24 VDC power supply
4 I/O module slots
Extension module holder for PCD3.Mxxxx/.Txxx/.Cxxx and PCD2.Mxxx
Additional PCD3.Cxxx devices connectable via connection plug or extension cable
Max. loading capacity: from internal 5 V bus 1500 mA,
from internal +24 V bus 200…630 mA (from HW version C)
Indication of internal 5 V supply voltage via LED
Connecting terminals for 24 VDC power supply for all connected PCD3 I/O modules,
plus any downstream PCD3.Cxxx module holders
Durchmesser = 11 mm
2 1
I/O terminal blocks and system cables are NOT included with I/O modules.
Steckeransicht
Etikette
PCD2.K231
Gummitülle Gummitülle
The PCD3.W745 temperature module is delivered with connector.
34 33 34 33
14 |
r
Overview of analogue input/output modules PCD3
Internal I/O
Total Signal ranges Electrical current draw connector
Type Resolution
I/Os isolation type� 3)
5 V ) 24 V 2)�)
1
Important: For an easy way to calculate required electric current, please use the Excel calculation table provided
under http://www.sbc-support.ch or under http://www.saia-burgess-controls.de
Consists of:
■ Battery module for slot #3 only
■ Lithium battery ��������������������������������
CR 2032�������������������������
(buffer time 1…3 years)
E
6
1 E
0 6
1
0
Without Clip With Clip
The Saia® Label Creator is supplied with PG5 Controls-Suite, but may also be downloaded from the
Internet support site: www.sbc-support.ch
16 |
www.saia-pcd.com Saia® PCD3.Mxxx0 - high performance, compact, modular
Web-HMI | Control & monitoring beyond system boundaries,
thanks to browser technology
(Details see TI 26/430, SI 26/432 and SI 26/428)
F8 F3
ESC F4
F9
F10 F5
F11 F6
Shif
t
F12
Ente
r
work.
F1
Shi
1
ft F5 F2
2
F6 F3
ab
gh
5,7“
c
i
7
3
F7
F4
pq
de
jkl
rs
f
,
8
.
6
F8
mn
tuv
o
0
9
wx
yz
+
-
En
ter
C
Te
xt
The Saia® S-Web concept
device with practically any control and display Saia® Web-Panel MB
stands for this to work reli- 3,5“
device. ably and efficiently, even in complex
➤ That is Web-HMI applications, without Java knowledge.
Windows in automation
even without plug-in cards and drivers
(Details see SI 26/456)
ably.
d
us
ir
-B
e
us
S
ct
t/
fib
B
ne
S
ro
U
er
P
th
E
C
e n
-L fi-
k
b e
S ro
in
- c
ll
ie
er
t
S
S
-C
Ja
ogy to the Windows platform. Plugin cards with
o
va
n
I
G
n
C
e
L
ct
TM
H
t
le
.N
L
et
TM
ct
H
ne
Ja
on
va
-C
S
.N
et
W atf
in or
pl
do m
w
s
Fi
le
ve
l
pl
at
R
em
fo
S ro f i b E I
B
ot
-B fi u B
rm
P ro N /
e
S
u S s- /..
I/
P O
t
s -B D .
O
e
s
rn
e
s /C
th
E
A
Dimensions drawing
PCD3.M3xx0
Dimensions drawing
PCD3.M5xx0 / PCD3.M6xx0
Type Description
Base units for 4 modules
PCD3.M3020 PLC with 128 KBytes of user memory, backup with 128 KBytes on board Flash memory,
up to 64 digital I/O (not expandable), 2 interrupts, web-server,
USB port for PG5, RS 485 for Profi-S-Net or S-Bus, 8 hours data protection with SuperCap
PCD3.M3120 like PCD3.M3020 but with Ethernet TCP/IP
PCD3.M3230 PLC with 512 KBytes of user memory, backup with 512 KBytes on board Flash memory,
up to 1023 digital I/O (with PCD3.Cxxx), 2 interrupts, web-server,
USB port for PG5, RS 485 for Profi-S-Net or S-Bus, 8 hours data protection with SuperCap
PCD3.M3330 like PCD3.M3230 but with Ethernet TCP/IP
PCD3.M5340 PLC with 1 MByte of user memory, backup with 1 MByte on board Flash memory,
up to 1023 digital I/O (with PCD3.Cxxx), 2 interrupts, web-server,
USB port for PG5, RS 232, RS 422/485 for Profi-S-Net and RS 485 for S-Bus, Ethernet TCP/IP
Run/Stop switch, 2 slots for PCD7.Rxxx, 1…3 years data protection with lithium battery
PCD3.M5440 PLC with 1 MByte of user memory, backup with 1 MByte on board Flash memory,
up to 1023 digital I/O (with PCD3.Cxxx), 2 interrupts, web-server,
USB port for PG5, RS 232, 2 × RS 485 for Profi-S-Net/MPI/S-Bus,
Run/Stop switch, 2 slots for PCD7.Rxxx, 1…3 years data protection with lithium battery
PCD3.M5540 like PCD3.M5440 but with Ethernet TCP/IP
PCD3.M6240 PLC with 1 MByte of user memory, backup with 1 MByte on board Flash memory,
up to 1023 digital I/O (with PCD3.Cxxx), 2 interrupts, web-server,
USB port for PG5, RS 232, RS 485 for Profi-S-Net/MPI/S-Bus, CAN interface
Run/Stop switch, 2 slots for PCD7.Rxxx, 1…3 years data protection with lithium battery
PCD3.M6340 like PCD3.M6240 but with Ethernet TCP/IP
PCD3.M6440 PLC with 1 MByte of user memory, backup with 1 MByte on board Flash memory,
up to 1023 digital I/O (with PCD3.Cxxx), 2 interrupts, web-server,
USB port for PG5, RS 232, RS 485 for Profi-S-Net/MPI/S-Bus, Profibus DP Master
Run/Stop switch, 2 slots for PCD7.Rxxx, 1…3 years data protection with lithium battery
PCD3.M6540 like PCD3.M6440 but with Ethernet TCP/IP
Flash memory modules and cards
PCD3.R500 1 MByte flash module on any I/O slot of all PCD3.M3xx0
PCD7.R500 1 MByte flash card for program and data backup on slot M1 or M2 of PCD3.M5xx0 and PCD3.M6xx0
PCD3.R550M04 4 MByte flash module with file system on any I/O slot of all PCD3.Mxxx0
PCD7.R550M04 4 MByte flash card with file system on slot M1 or M2 of PCD3.M5xx0 and PCD3.M6xx0
PCD3.R551M04 4 MByte flash module with 3 MByte file system and 1 MByte program backup on any I/O slot of all PCD3.Mxxx0
PCD7.R551M04 4 MByte flash card with 3 MB file system and 1 MB program backup on slot M1 or M2 of PCD3.M5xx0 and PCD3.M6xx0
PCD3.R560 *) 2 MByte BACnet flash module on any I/O slot of all PCD3.Mxxx0
PCD7.R560 *) 2 MByte BACnet flash card on Slot M1 or M2 of PCD3.M5xx0/M6xx0
PCD3.R561 *) 2 MByte BACnet flash module with 1 MB file system and 1 MB program backup on any I/O slot of all PCD3.Mxxx0
PCD7.R561 *) 2 MByte BACnet flash card with 1 MB file system and 1 MB program backup on Slot M1 or M2 of PCD3.M5xx0/M6xx0
PCD3.R600 PCD3 base module for SD flash memory cards with file system on any I/O slot of all PCD3.Mxxx0
PCD7.R-SD256 256 MByte Saia® SD flash memory card with file system
PCD7.R-SD512 512 MByte Saia® SD flash memory cards with file system
Data protection
PCD3.R010 Battery kit for PCD3.M3xx0 on I/O slot 3
4 507 4817 0 Lithium battery for PCD CPUs and PCD7.D73 to .D78 terminals (RENATA button type CR 2032)
4 639 4898 0 Battery holder for PCD3.M5xxx and PCD3.M6xxx
I/O Module holder, connection plug and connection cables
PCD3.C100 Module holder for 4 I/O modules
PCD3.C110 Module holder for 2 I/O modules
PCD3.C200 Module holder for 4 I/O modules with screw terminal block for external 24 VDC power supply
4 104 4952 0 Screw terminal block 2-pole for external 24 VDC power supply of PCD3.C200
4 104 5005 0 Bolting device to screw terminal block 2-pole for external 24 VDC power supply of PCD3.C200
PCD3.K010 Connection plug PCD3 ↔ PCD3
PCD3.K106 Connection cable 0.7 m PCD3 ↔ PCD3
PCD3.K116 Connection cable 1.2 m PCD3 ↔ PCD3
*) The BACnet option is only available for PCD3 controller with Ethernet
Communications modules on I/O slot 0 – terminal blocks (type A or B) must be ordered separately
PCD3.F110 with RS 422 / RS 485 interface (electrically connected), terminal block type A or B
PCD3.F121 with RS 232 interface (suitable for modem), terminal block type A or B
PCD3.F130 with 20 mA current loop interface, terminal block type A or B
PCD3.F150 with RS 485 interface (electrically isolated), terminal block type A or B
PCD3.F180 Belimo MP-Bus for up to 8 actuators, terminal block type A or B
Communications modules on I/O slots 0…3
PCD3.F210 with RS 422 / RS 485 interface with socket for PCD7.F1xx module, terminal block type K included
PCD3.F221 with RS 232 interface with socket for PCD7.F1xx module, terminal block type K included
PCD3.F281 with 1 x Belimo MP-Bus and 1 socket for PCD7.F1xx module
Accessories
Type A Type B Type C Type E Type F Type G Type H Type J Type K
Plug-in system cables for manual control and light & shade modules
PCD3.K800 1.0 mm², 2.5 m long, PCD side: 8-pole, plug-in spring terminal block type J; process side: strand ends free, numbered
PCD3.K810 1.0 mm², 2.5 m long, PCD side: 12-pole, plug-in spring terminal block type F; process side: strand ends free, numbered
PCD3.K860 1.5 mm², 2.5 m long, PCD side: 4-pole, plug-in spring terminal block type G; process side: strand ends free, numbered
PCD3.K861 0.75 mm², 2.5 m long, PCD side: 6-pole, plug-in spring terminal block type H; process side: strand ends free, numbered
Spring terminal block 8-pole for all PCD3.Mxxxx
4'405'4995'0 Spring terminal block 8-pole for power supply, RS 485, Interrupt inputs and Watch dog of all PCD3.Mxxx0
Terminal blocks, Inscription
4'405'4954'0 Plug-in I/O spring terminal block (type A), 10-pole for wiring up to 2.5 mm2, numbered from 0…9
4'405'4955'0 Plug-in I/O screw terminal block (type B), 10-pole for wiring up to 2.5 mm2, numbered from 0…9
4'405'4956'0 Plug-in I/O spring terminal block (type C), 24-pole for wiring up to 1.0 mm2, numbered from 0…23
4'405'4998'0 Plug-in I/O spring terminal block (type E), 14-pole for wiring up to 1.5 mm2, numbered from 0…13
4'405'4936'0 Plug-in I/O spring terminal block (type F), 12-pole for PCD3.A810 for wiring up to 1.5 mm2, numbered from 0…12
4'405'5027'0 Plug-in I/O spring terminal block (type G), 4-pole for PCD3.A860 for wiring up to 2.5 mm2, numbered from 0…4
4'405'5028'0 Plug-in I/O spring terminal block (type H), 6-pole for PCD3.A860 for wiring up to 1.0 mm2, numbered from 1…6
4'405'4934'0 Plug-in I/O spring terminal block (type J), 8-pole for PCD3.W800 for wiring up to 1.5 mm2, numbered from 1…8
4'405'5048'0 Plug-in I/O spring terminal block (type K), 10-pole for wiring up to 1.0 mm2, numbered from 0…9
Addressing and marking I/O modules and module holders
4'329'4819'0 Set of 10 pcs.: Inscription labels for PCD3 I/O
4'310'8686'0 Set of 10 pcs.: Preprinted adhesive strips for PCD3 I/O
4'310'8723'0 Set of 10 pcs.: cover including neutral inscription labels (2 × DIN A4)
Dummy module and covers
PCD3.E009 Dummy module, as contact protection for unequipped PCD3 sockets
4'104'7493'0 Cover for flash card and battery slots of PCD3.M5xxx and ..M6xxx
4'104'7502'0 Slot cover for PCD3 I/O‘s (neutral),
4'104'7515'0 Slot cover for PCD3 I/O‘s (with logo – Saia® PCD3)
Contact
Switzerland and international This brochure was received from:
Saia-Burgess Controls Ltd.
Bahnhofstrasse 18
CH-3280 Murten / ������������
Switzerland
T +41 26 / 672 71 11
F +41 26 / 672 74 99
pcd@saia-burgess.com
www.saia-pcd.com
Product support,
Technical reference website: www.sbc-support.ch
P+P26/397 E10 09. 2008
Subject to change without notice.
Revision: Language:
AH S - K R S - 0 0 - O E A- D A- 0 0 - 0 0 1
A EN
DIN rail power supply unit 24 V DC/5 A, primary switched-mode, 1-
phase.
Product notes
WEEE/RoHS-compliant since:
Commercial data 03/21/2006
EAN
4 017918 890520
Pack 1 Pcs.
Customs tariff 85044082
Product key CMPP13 http://
www.download.phoenixcontact.com
Catalog page information Page 480 (IF-2007) Please note that the data given
here has been taken from the
online catalog. For comprehensive
information and data, please refer
to the user documentation. The
General Terms and Conditions of
Use apply to Internet downloads.
Product description
QUINT POWER is the powerful 60 - 960 W DC power supply unit for universal use. With its wide-range input, single and
three-phase versions, and international approval package, this solution is unrivalled. QUINT POWER provides reliable
power supply: generously dimensioned capacitors ensure mains buffering of over 20 ms at full load. Full output power
is provided by all three-phase devices, even in the event of a permanent phase failure. The Power Boost power reserve
easily starts loads with high inrush currents and ensures that fuses are reliably tripped. Preventive function monitoring
diagnoses impermissible operating states and minimizes downtimes in your system. Remote monitoring is provided by
an active transistor switching output and a floating relay contact. All devices are idling-proof and short-circuit-proof, and
are available with a regulated and adjustable output voltage of 12, 24, and 48 V DC with output currents of 2.5, 5, 10, 20,
30, and 40 A. Power supply units for use in Ex zone 2, uninterruptible solutions, AS-i power supply units, and a QUINT
diode complete this comprehensive product range.
Technical data
Input data
Nominal input voltage 100 V AC ... 240 V AC
AC input voltage range 85 V AC ... 264 V AC
DC input voltage range 90 V DC ... 350 V DC
AC frequency range 45 Hz ... 65 Hz
DC frequency range 0 Hz
Current consumption Approx. 1.6 A (120 V AC)
Approx. 0.84 A (230 V AC)
Nominal power consumption 120 W
Inrush surge current < 20 A (typical)
Power failure bypass > 30 ms (120 V AC)
> 130 ms (230 V AC)
Input fuse 5 A (slow-blow, internal)
Permissible backup fuse B6
B10
B16
Type of protection Transient surge protection
Protective circuit/component Varistor
Output data
Nominal output voltage 24 V DC ±1%
Setting range of the output voltage 22.5 V DC ... 28.5 V DC
Output current 5 A (up to 60°C)
7.5 A (with POWER BOOST)
Derating 60 °C (2.5%/K)
Connection in parallel Yes, for redundancy and increased capacity
Connection in series Yes
Max. capacitive load Unlimited
Current limitation Approx. IBOOST = 7.5 A (for short-circuit)
Control deviation < 1 % (change in load, static 10% ... 90%)
< 2 % (change in load, dynamic 10% ... 90%)
< 0.1 % (change in input voltage ±10%)
Residual ripple < 10 mVPP (with nominal values)
General data
Width 55 mm
Height 130 mm
Depth 125 mm
Width with alternative assembly 122 mm
Height with alternative assembly 130 mm
58 mm
Net weight 0.83 kg
Operating voltage display Green LED
Efficiency > 89 %
Insulation voltage input/output 4 kV AC (type test)
2 kV AC (routine test)
Degree of protection IP20
Protection class I, with PE connection
MTBF (IEC 61709, SN 29500) > 500000 h
Ambient temperature (operation) -25 °C ... 70 °C (> 60 °C derating)
Ambient temperature (storage/transport) -40 °C ... 85 °C
Max. permissible relative humidity (operation) 95 % (at 25 °C, no condensation)
Mounting position horizontal DIN rail NS 35, EN 60715
Assembly instructions Can be aligned: Horizontally 0 mm, vertically 50 mm
Electromagnetic compatibility Conformance with EMC directive 89/336/EC
Noise emission EN 50081-2
Noise immunity EN 61000-6-2:2005
Standard – Electrical equipment of machines EN 60204
Standard - Safety of transformers EN 61558-2-17
Standard - Electrical safety EN 60950-1/VDE 0805 (SELV)
EN 61558-2-17
Shipbuilding approval Germanischer Lloyd (EMC 2), ABS
Standard – Electronic equipment for use in EN 50178/VDE 0160 (PELV)
electrical power installations and their assembly
into electrical power installations
Standard – Safety extra-low voltage EN 60950-1 (SELV)
EN 60204 (PELV)
Signaling
Output name DC OK active
Output description UOUT > 0.9 x UN: High signal
Certificates / Approvals
Certification CB, CUL, CUL Listed, DNV, GL, GOST, UL, UL Listed
Drawings
Block diagram
Diagram
Figure 1 Features
Technical Data
General Data
Supply voltage UB 19.2...30 V DC
Current consumption at 24 V DC < 40 mA
(incl. 20 mA load current)
Power consumption < 600 mW
Transmission error < 0.2% of end value
Temperature coefficient
max. < 0.01%/K
typ. < 0.002%/K
Cut-off frequency (3 dB) 100 Hz
Step response (10...90 %) 3.5 ms
Test voltage (input / output / supply) 1.5 kV, 50 Hz, 1 min.
Ambient temperature range
Operation -20°C…+60°C (-4°F...140°F)
Storage -40°C…+85°C (-40°F...185°F)
Dimensions (W x H x D) 6.2 mm x 93.1 mm x 102.5 mm
(0.244 in. x 3.665 in. x 4.035 in.)
Conductor cross section 0.2...2.5 mm2 (AWG 24...12)
Stripping length
Screw connection 12 mm
Spring-cage connection 8 mm
Housing design Polybutylenterephthalate PBT, green
Tests / Approvals
cu
U PROCESS CONTROL EQUIPMENT FOR
HAZARDOUS LOCATIONS
LISTED 31ZN
Class I Div 2 Groups A, B, C, D T5
A) This equipment is suitable for use in Class I,
Division 2, Groups A, B, C and D or non-hazardous
locations only.
B) Warning - explosion hazard - substitution of
components may impair suitability for Class 1,
Division 2.
C) Warning - explosion hazard - do not disconnect
equipment unless power has been switched off or the
area is known to be non-hazardous.
MINI MCR-SL-RPS-I-I(-SP)
Conformance With EMC Guideline 89/336/EEC And Low Voltage Directive 73/23/EEC
Immunity to Interference According to EN 61000-6-21
Discharge of static electricity (ESD) EN 61000-4-2 Criterion B2
Electromagnetic HF field EN 61000-4-3 Criterion A3
Fast transients (Burst) EN 61000-4-4 Criterion B2
Surge voltage capacities (Surge) EN 61000-4-5 Criterion B2
Conducted disturbance EN 61000-4-6 Criterion A3
Noise Emission According to EN 50081-2
Noise emission of housing EN 550114 Class A5
1
EN 61000 corresponds to IEC 1000
2
Criterion B: Temporary impairment to operational behavior that is corrected by the device itself.
3 Criterion A: Normal operating behavior within the defined limits.
4
EN 55011 corresponds to CISPR11
5
Class A: Area of application industry.
MINI MCR-SL-RPS-I-I(-SP)
Ordering Data
Description Order Designation Order No.
Repeater power supply MINI MCR-SL-RPS-I-I 28 64 42 2
Screw terminal block
Repeater power supply MINI MCR-SL-RPS-I-I-SP 28 64 75 2
Spring-cage terminal block
Accessories
Description Order Designation Order No.
DIN rail bus connectors ME 6,2 TBUS-2 1,5/5-ST-3,81 GN 28 69 72 8
Power terminal block with screw connection MINI MCR-SL-PTB 28 64 13 4
Power terminal block with spring-cage connection MINI MCR-SL-PTB-SP 28 64 14 7
System power supply MINI-SYS-PS-100-240AC/24DC/1,5 28 66 98 3
MINI MCR-SL-RPS-I-I(-SP)
Installation
The device may only be installed and put
into operation by qualified personnel.
The corresponding national regulations
(e.g. VDE, DIN) must be observed.
Block Diagram
PLC relay, consisting of base terminal block PLC-BSC.../21 with screw
connection and pluggable miniature relay with power contact, for
assembly on DIN rail NS 35/7.5, 1 PDT, input voltage 24 V AC/DC
Product notes
WEEE/RoHS-compliant since:
Commercial data 23/01/2006
EAN
4 017918 130725
Pack 10
Customs tariff 85364190
Country of Origin DE Please note that the data given
here has been taken from the
Catalog page information Page 82 (IF-2011) online catalog. For comprehensive
information and data, please refer
to the user documentation at http://
www.download.phoenixcontact.com.
The General Terms and Conditions
of Use apply to Internet downloads.
Technical data
Coil side
Nominal input voltage UN 24 V AC/DC
Nominal input current at UIN 11 mA (at UN = 24 V AC)
8.5 mA (at UN = 24 V DC)
Typical response time 6 ms
Contact side
Contact type Single contact, 1-PDT
Contact material AgSnO
Maximum switching voltage 250 V AC/DC (The separating plate PLC-ATP should be installed
for voltages larger than 250 V (L1, L2, L3) between identical
terminal blocks in adjacent modules. Potential bridging is then
carried out with FBST 8-PLC... or ...FBST 500...)
Minimum switching voltage 5 V (at 100 mA)
Maximum inrush current (on request)
Min. switching current 10 mA (at 12 V)
Limiting continuous current 6A
Interrupting rating (ohmic load) max. 140 W (at 24 V DC)
20 W (for 48 V DC)
18 W (for 60 V DC)
23 W (for 110 V DC)
40 W (for 220 V DC)
1500 VA (for 250 V AC)
General data
Width 6.2 mm
Height 80 mm
Depth 94 mm
Test voltage relay winding/relay contact 4 kV AC (50 Hz, 1 min.)
Ambient temperature (operation) -40 °C ... 60 °C
Ambient temperature (storage/transport) -40 °C ... 85 °C
Operating mode 100% operating factor
Mechanical service life 7
2 x 10 cycles
Inflammability class according to UL 94 V0
Name Standards/regulations
Standards/regulations IEC 60664
EN 50178
IEC 62103
Pollution degree 3
Connection data
Connection method Screw connection
Conductor cross section solid min. 0.14 mm²
Conductor cross section solid max. 2.5 mm²
Conductor cross section stranded min. 0.14 mm²
Conductor cross section stranded max. 2.5 mm²
Conductor cross section AWG/kcmil min. 26
Conductor cross section AWG/kcmil max 14
Stripping length 8 mm
Screw thread M3
Certificates
Drawings
Diagram
Interrupting rating
Circuit diagram
WH: 35 x 35 AC230VA
58
AC 24, 48, 115, 230 24, 48, 115, 230 24, 48, 115, 230 24, 48, 115, 230
Standard
50/60Hz C3-A30 X / AC ..... V C3-T31 X / AC ..... V C3-T32 X / AC ..... V C3-R20 / AC ..... V
DC 12, 24, 48, 110, 125, 220 12, 24, 48, 110, 125, 220 12, 24, 48, 110, 125, 220 12, 24, 48, 110, 125
Standard
≤ 10% C3-A30 / DC ..... V C3-T31 / DC ..... V C3-T32 / DC ..... V C3-R20 / DC ..... V
DC 12, 24, 48, 110, 125, 220 12, 24, 48, 110, 125, 220 12, 24, 48, 110, 125, 220
D, DX
≤ 10% C3-A30D X / DC ..... V C3-T31D X / DC ..... V C3-T32D X / DC ..... V
9 8 7 5 3 4
10A 250V A
34 32 24 22 14 12
30
SWISS
9 3
04
10 2
Clip S3-C
Ordering example C 11 A 11 1
10A
400V A
38 4 20 38 4 22
COMAT AG CH-3076 WORB CR 4.01/4.00-1 E This edition replaces all previous issues. Availability, errors and specification subject to change without notice.
3
Revision: Language:
AH S - K R S - 0 0 - O E A- D A- 0 0 - 0 0 1
A EN
1 2 3 4 5 6 7 8 9 10
1 Surge arrester
10 Switch disconnector
Accessory
Auxiliary switch and signal contacts 1/16
Dummy, housing, Neutral disconnector, shunt trip 1/17
F4C-ARI motor operating devices 1/18
Busbar system
Starter pack 1/19
Sockets, Additional socket 1/20
Additional socket, terminals 1/21–22
Incoming terminal block and components 1/23
Socket accessories 1/24
Combi module 32 A 1/25
32 A and 63 A universal adapters 1/26–27
Miscellaneous accessories 1/27
Busbars/selection table for sockets 1/28