Professional Documents
Culture Documents
RING FINISSH
FLOOR
Type
A two component polyyamide catalyysed coating.
Especiallyy designed to provide a deccorative floor coating wherre durability iss required.
Flooring
Finiish Characteeristic
Page | 1 o Outsttanding adhession to steel, cconcrete and galvanize
o High ffilm build cap pability on singgle coat appliccation
o Provid de durable, high adherent protective coating
o Outsttanding abrasion resistancee.
o Wateer and salt watter resistant
o Chem mical resistant
Applicatiion
o Floor Coating
o Decorative Protecttive Coating
Technicaal Specification
Package : 2 co omponent
Color : full range colors
RALL Colour rangee
Finish : Glosssy
Specific G Gravity : basee : 1.45 _+0.0 05, hardener : 0,95_+0,05
Viscosity : 110 0 KU
Pot life (2 28*C) : 5 ho ours
Mixing Ratio by weight : 80 p parts base : 200 parts harden ner
Solid con ntent : base : 74 _+2% % ‐ by weight
Hardener : 30 0 _+ 1 %
DFT 100 microns Tackk free : 16 hours at 300 C
Recommended Dry : 100 microns per ccoat
Film Thicckness
Theorecaal coverage : 200 gr/m2 at 100 0 microns
When estimating workking coveragees, allow for ap pplication lossses, surface irrregularities, eetc
Flash Point : Basee : 17 0 C
Hard dener : 11 0 C
C
0
Shelf life at 20 C : 1 yeear
Surface P Preparation
Remove completely alll dirt, grease, oil, water or other contam minants from ssurface to be ccoated.
TM
Applicatiion Instructio on
Recommended : Dry : 35 ‐ 50 micrrons
Film Thicckness per coaat Wett : 70 ‐ 100 miicrons
Flooring ReCoat In nterval : Minnimum : 15 ho ours at 300 C;
Maxximum : 7 dayys at 300 C
Finiish
Page | 2 Application Method : Airleess spray, or bbrush
Thinner : Thin
nner 02
Dilution R Ratio : 3 – 10 % ‐‐ by airless spray,
Mixing raatio by weightt : Basee 80 parts to HHardener 20 p parts
Aging timme 20*C : Let sstand approx.. 30 minutes
Pot life : 4 hoours at 30*C
DFT 100 microns : 7 daays at 30*C
Instructio on Preparatio on
1. Mix base and Hardener in acccordance with h the specified mixing ratio
o, then stir th
horoughly un
ntil it is of
uniform constituen ncy prior to application. If the proportio on is varied, neither cure no or expected pproperties
may rresult.
2. Use u up the mixed m material withiin pot life
3. Application in exceess of the speccified coating intervals mayy cause the lacck of adhesivee properties. SShould be
over ccoated within n the specifiedd intervals. W
When exceeds, rough the paainted surfacee with sand paaper, then
clean with rags.
4. Clean n all equipmen nt immediatelly after use wiith thinner or solvent
5 Remo ove completelly all dirt,grease,oil,water o or other contaaminant from surface to be coated
6 For first coat applyy very thin coaating (dilute th
he paint bt 1:1 1 with agatha epoxy coating)
to maake sure the p paint penetratte the surface.
Precautio ons
This prod duct is flammable, keep aw way from heat or open heaat or open flaames. As geneeral rules, inhalation of
solvent o of paints mist and contact o of liquid paint with skin or e eyes should bee avoided. Forced ventilation should
be provided when appliying in confinend spaces. s Respiiratory, skin and eyes p protection arre always
recommeended.