Professional Documents
Culture Documents
General PH400G
Specifications 4-Wire Type pH Meter
GS 12B7C1-E
GENERAL
The EXA PH intelligent pH conveter is a highly reliable
advanced function pH measurement system designed for
wide application in all industries such as for medium-scale
waste water treatment system, and general-purpose pH
measurement and control systems.
The EXA PH intelligent pH converter features highly
effective built-in functions for sensor diagnosis similar to
FLXA21 2-wire liquid analyzer. These functions monitor
sensor errors even while pH measurements are in
progress, enabling more highly reliable pH measurement.
The converter also offers an interactive system for setting
the various parameters, facilitating effective use of its
wealth of functions.
The EXA PH intelligent pH converter is available not only
in versions for general-purpose applications but also for
high-purity water service.
d KCL refillable type d Xerolyt d Guide Pipe d Suspension Type Holder d 4-wires pH Converter
PH8ERP HA405/HA485 PH8HG HH350G PH400G
<No Cleaning> <With Jet Cleaning>
pH
MEASURE
AUT CAL
MAN CAL
TCMP
DISP
HOLD
CONTACTS
YES NO MODE
S1
S2
S3
>
>
ENT
FAIL
d for Chemical
DPA405/DPA485
d Angled Floating Ball Holder
d Submersion Type Holder PB350G
d Hydrofluoric
Acid-resistive
HF405
MEASURE
AUT CAL
MAN CAL
TCMP
DISP
HOLD
>
NO MODE
CONTACTS
S1
S2
S3
>
ENT
KCL Solution
FAIL
F1-a.b.c.EPS
CAUTION
Installation Location of Holders (Guide Pipe, Submersion Type, etc)
The holder should be used in a place that is as vibration free as possible.
Using the holder in a place where it is affected by vibration, may result in damage to the holder.
All Rights Reserved. Copyright © 1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 3
SPECIFICATIONS Notes:
(*1): The solution temperature should preferably be
below 808C when the pH value is in the range 11 to
EXA PH Series General Specifications 14. Even if the solution is below 808C, sensor
Measured object: Hydrogen ion concentration (pH) in service life may be shortened in store solutions. In
aqueous solutions such cases the KCl filling type is recommended.
(*2): Maximum temperature 508C when Hard PVC guide-
Measuring principle: Glass electrode method
pipe is used.
Measuring range: 0 to 14 pH (*3): For flow-through types, refer also to the solution
Measuring conditions: temperature and pressure graph (in notes following
Solution temperature: See Table 1, for high-purity Model and Suffix code table for flow-through type
water, 0 to 508C holders).
Solution pressure: See Table 2, for high-purity water, (*4): Solutions with normal pH ranges of 3 to 14 are
atmospheric pressure (measured liquid recommended for stainless steel (SUS316).
outlet side open to atmosphere)
Solution flow rate: Max. 2 m/s for submersion guide-
pipe type 3 to 11 l/min for flow-through Table 2. Process Pressure Range
type, for high-purity water, see Figure 2. pH
Solution conductivity: Min. 50 mS/cm, for high-purity Sensor PH8ERP PH8EFP
water, see Figure 1. Holder
Temperature compensation range: -10 to 1308C (for Submersion
Atmospheric pressure (Submersion depth: Max. 3 m)
pH converter)
Guide-pipe Atmospheric pressure
Suspension
Table 1. Process Temperature Range Float (Submersion depth: Max.3 m)
(a) pH and Liquid Temperature Ranges for pH sensors Atmospheric pressure to 10 kPa
when general purpose reserve
Atmospheric tank used.
Solution Solution Flow-through pressure
pH Sensor Holder Type Temperature to 50 kPa Atmospheric pressure to 500 kPa
pH Ranges Ranges (8C) when medium-pressure reserve
tank used.
Guide-pipe *3 *2
KCl refilable Solution 2 to 12 -5 to 80 (Note 1) For flow-through types, refer also to the solution temperature
type Flow-through and pressure diagram of Holder GS 12J5C2-E.
T03.EPS
*2
Guide-pipe 2 to 12 -5 to 80
KCl filling Submersion *3 *1 *1
0 to 14 -5 to 105 700
type
ml/min
Flow-through
600
T01.EPS
500
Solution flow rate
400
(b) Solution Temperature Ranges for Holders
300
Usable range
Liquid 200
Holder Type Holder Cleaner Temperature
Material 100
(8C)
0
PV None -5 to 50 0 0.1 0.2 0.3 0.4 0.5 0.6 50
Guide-pipe
PP None -5 to 80 Solution conductivity (mS/cm)
F02.EPS
None -5 to 100
PP
Provided -5 to 80 Figure 2 Solution flow rate and solution conductivity of sensor
Submersion and holder for high purity water
*4 None -5 to 100
S3
Provided -5 to 80
None -5 to 80
PP
Flow-through Provided -5 to 80
*3 *4 None -5 to 105
S3
Provided -5 to 80
T02.EPS
PV: Hard PVC
PP: Polypropylene
S3: Stainless steel (SUS 316)
All Rights Reserved. Copyright ©1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 4
1. pH Sensors: PH8ERP, PH8EFP, PH8EHP Table 4. Utilities (For Jet Cleaning or Brush Cleaning)
A compound sensor assembly consisting of glass Pressure (kPa) Flow Rate
electrode, reference electrode, temperature sensor, and
ground tip. Water jet 200 to 400 + Liquid pressure 5 to 20 l/min
Type: KCl filling and KCl refillable types Water brush 100 to 250 + Liquid pressure 20 to 30 l/min
Measuring range: 0 to 14 pH for KCl refillable type; normal Air jet 200 to 400 + Liquid pressure 100 to 300 Nl/min
pH =2 to 12 pH)
Air brush 150 to 250 + Liquid pressure 300 to 600 Nl/min
Refer to "Selection Criteria for pH Sensors and Holders"
T06.EPS
shown on the last page to select KCl filling or refillable
type sensors.
Temperature compensation sensor: Platinum RTD 2.2 Holder For High-purity Water: PH8HH
(Pt1000) Materials: Acrylic resin, SUS316, chloroprene rubber
Wetted part materials: Process connections: Rc1/4 (inlet) and R1/2 (outlet),
or 1/4 NPT (inlet) and 1/2 NPT (outlet)
pH Sensor Wetted parts materials Mounting: Mount on 50 A vertical or horizontal pipe, or
wall-mount (specify mounting hardware)
Ryton (PPS resin), glass, ceramics, titanium Weight:
or Hastelloy C, fluorocarbon rubber and Body: 1.7 kg
KCl refillable type
chlorinated polyethylen rubber (carbon sheath
Mounting hardware: 0.7 kg
only when suspended in guide-pipe)
All Rights Reserved. Copyright © 1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 5
Contact Output Contact ON / OFF
?Contact output function that can be set
S1, S2, S3 FAIL
Contact Function Power Power
Setting (free selectable) Operation (free selectable) ON OFF ON OFF
S1 OFF, low limit, high limit, ON/OFF, Proportional duty pulses
*1
ON Closed ON Closed
HOLD Proportional frequency pulses *2 Action Open Action Closed
OFF Open OFF Open
OFF, low limit, high limit, Ditto T08.EPS
S2
HOLD
OFF, low limit, high limit, Ditto When closed, each indicator lamp is lit corresponding to
S3 HOLD, Cleaning timer, each contact status.
Hi - Hi limit, Lo - Lo limit ?Contact Type: Relay contact output (dry contact)
?Contact Rating
FAIL Failure ON/OFF
250 V AC, 2 A, Max. 100 VA
T07.EPS
(*1) and (*2) are effective when the low high limit contact 220 V DC, 2 A, Max. 50 W
Contact Input: Dry contact for manual start for automatic
output is to be used.
cleaning
(*1) Proportional duty pulse Ambient Temperature: -10 to 558C
Example of high limit alarm (conrol) output (hood may be fitting as option)
Storage Temperature: -30 to 708C
% duty cycle control 10% Ambient Humidity: 10 to 90% RH
90% Construction: Watertight complying with JIS C0920
100 equivalent to NEMA 4 waterproof
construction
Material:
Case; Aluminum alloy casting
Cover and window; Polycarbonate
50% 50% Finish: Baked polyurethane resin coating
50 Colors:
t on t off Cover; Deep sea moss green (Munsell 0.6GY3.1/2.0)
Case; Frosty white (Munsell 2.5Y8.4/1.2)
Mounting: Pipe mounting, wall mounting or rack
mounting
10% 90% Panel mounting
0 Power Supply Voltage: 88 to 132 V AC, 50 / 60 Hz
Proportional pH Duty cycle 176 to 264 V AC, 50/60 Hz
Setpoint range Time
% of output range Power Consumption: Approx. 8.5 VA
F02.EPS
Electrical Connection:
pH sensor: Watertight plastic gland equivalent to JIS
(*2) Proportional frequency pulse
A8 attached to pH sensor side, f13.5 hole
Example of high limit alarm (conrol) output
Others: Watertight plastic gland equivalent to JIS A15
% controller output (for cable OD. 9 to 12 mm) attached, f21
hole
100 Weight:
Maximum pulse frequency Body: Approx. 2.5 kg
Mounting bracket: Approx. 0.4 kg
Dimensions: 144 (W) x 144 (H) x 135 (D) mm
0.3 s
Function Specifications
Input Impedance: 1012 V or more
50 Note: Use a sensor with solution earth sensor because of
50% pulse frequency differential amplifier (that uses two high-impedance
amplifiers).
Asymmetry Potential Adjustable Range: pH 7 6 2 pH
Slope Adjusting Range: Adjustable in the range from 70 %
to 110 % of the theoretical value.
Automatic Temperature Compensation Range:
0 -10 to 1308C (manual compensation is also available)
Proportional pH No pulses Time
Reference Temperature Conversion Coefficient
range
Setpoint % of output range (Reference Temperature 258C):
F03.EPS
On shipment: 0
Settable parameters Adjustable range: -1.00 to 1.00 pH / 108C
? pH value setpoint Conversion to the reference temperature is used only
? Control range for high-purity water or when the measured
? Pulse periode solution temperature coefficient is known.
All Rights Reserved. Copyright ©1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 6
Standard Performance Setting of reference electrode impedance high limit
(performance when combined with a pH sensor) value
Repeatability: 0.05 pH (sensor submerged 3 times in Setting of response time high limit value
the same buffer solution) One-point temperature calibration
Response Time: 10 sec (90 % response, using pH Sensor type selection (glass electrode or
sensor and buffer solution both at antimony electrode)
temperature equilibrium at 208C, with Error reset
adequate agitation) pH display value selection (0.1 pH / 0.01 pH)
Accuracy: 60.1 pH (using KCl filling type pH sensor Half value recovery time check ON / OFF
or high-purity water pH sensor ) Half value recovery time setting (0.1 to 10 min)
60.15 pH (using KCl refillable pH Burn-up or burn-down ON/OFF
sensor) Response stabilization judging parameter setting
Temperature Repeatability: 18C Auto-return (approx. 60 min) ON/OFF
pH standard solution temperature characteristics
setting
Operating Functions
Temperature sensor cable length correction
Display: 3 1/2 digit digital display (data display)
Signal output selection
Six digit alphanumerics (message or data display)
Display function: 4 to 20mA DC OFF, pH Temperature
pH value
Temperature value 0 to 1V DC OFF, pH Temperature
mA output T09.EPS
All Rights Reserved. Copyright © 1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 7
4. Ultrasonic Oscillator (Model PUS400G) Cleaning water outlet flow rate: Max. 30 l/min,
Combination device: (which can be regulated by the bypass valve.)
Holder with ultrasonic cleaner (PH8HS, PH8HF) Connectable unit: Holder or sensor with the jet cleaning
Connection cable are provided with holders. system
Cleaning method: Continuous ultrasonic emission Tank: With a ball tap (ball float valve for level control)
(Frequency sweep method) Effective capacity of approx. 40 liters.
Oscillation frequency: Approx. 61 to 81 kHz Pump: Suction pump with capacitor-starting-type
Output voltage: Approx. 40 to 70V induction motor. Equipped with an electro-
Power supply: 100/110/115/200/220/240 V AC610% magnetic actuator with overcorrect protec-
50/60 Hz tion.
Power consumption: Approx. 15 VA Cleaning water inlet connection:
Ambient Temperature: -10 to 50 8C G 1/2
(hood may be fitting as option) Cleaning water outlet connections:
Storage Temperature: -25 to 70 8C G 1/2 (Optional Rc 1/2 or ANSI 1/2NPT adapters are
Construction: JIS C0920 Watertight (NEMA 4 equivalent available.)
waterproof construction) Electric connection:
Material: Case: Aluminum alloy casting Plastic watertight gland equivalent to JIS A15.
Window: Polycarbonate Applicable cable outside diameter: 9 to 12 mm
Mounting bracket: Stainless steel Conduit adapter: Optional
Finish: Baked polyurethane resin (Standard) Ambient temperature: 5 to 508C
Baked epoxy resin (Option) Power supply: 100 or 200 V AC 610%, 50/60 Hz, single
Color: Case; Frosty white (Munsell 2.5Y8.4/1.2 or phase
equivalent) (Must be equal to the converter’s power supply.)
Cover; Deep sea-moss green (Munsell 0.6GY3.1/ Power consumption: 0.4 kW
2.0 equivalent) Construction: For installation outdoors (in a place safe
Mounting: (2-inch) pipe mounting, wall or rack mounting from rain, wind, and direct sunlight)
or panel mounting Color: Light gray (Munsell 2.8GY6.4/0.9 equivalent)
Cable inlet: f22.7 x 2 Pg16 watertight plastic gland Dimensions: Approx. 442 (W) x 804 (D) x 800 (H) mm
Cable / Terminal: For 7 to 12 mm, M4 Finish: Baked polyurethane
Conduit adapter: Power Supply side only (Option) Weight: Approx. 55 kg
Connection: G 1/2 or 1/2 NPT
7. Terminal Box PH8TBG
Weight: Body; Approx. 2.5 kg
Mounting bracket; Approx. 0.7 kg Used when pH converter is installed remotely from the
(Note) Output of ultrasonic oscillator changes with power pH sensor.
supply voltage or connected cable length. Ambient temperature: -10 to 50 8C
Construction: JIS waterproof
5. Solenoid Valve for Jet/Brush Cleaning PH8MV Case material: Fiberglass reinforced polycarbonate resin
Pilot kick operated, 2-port valve. Open when energized. Case color: Grayish green (Munsell 2.5GY5.0/1.0)
Electrical connections:
Fluid: Normal tap water, industrial water, or air
pH Converter side:
Operating pressure: 0 to 1 MPa
f21 mm hole (With G1/2 plastic gland)
Forward (reverse) pressure resistance: 2 MPa
pH sensor side:
Fluid temperature: Water; 5 to 608C , Air; -10 to 608C
f13 mm hole (With G1/2 plastic gland)
Cv: 4.5
With Cable (Maximum length 20 m)
Process connection: Rc 1/2
Conduit adapter (optional)
Power supply: 100/110/200/220 V AC, 50/60 Hz
Construction: IP53 8. Accessories (Purchased Separately)
Material:
Body: Bronze See Model and Suffix Codes.
Sealing: Nitrile rubber
Ambient temperature: Maximum 508C
Electric connection: G 1/2
Weight: Approx. 0.9 kg
All Rights Reserved. Copyright ©1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 8
MODEL AND SUFFIX CODES 1. pH Sensors
When ordering, specify model and codes, product name For selection of KCl filling or refillable type pH sensors,
and / or part numbers. refer to "Selection Criteria For pH Sensors and Holders"
on page 24, and "Table of Corrosion-Resistant Materials"
on page 25 of this manual.
Item to be specified.
PH8ERP, d KCl Refillable Type pH Sensor
1. pH Sensor
PH8EFP
Model Suffix Code Option Specifications
PH8HG, PH8HS, Code
2. Holder KCl Refillable Type
PH8HF or PH8HH PH8ERP pH Sensor
3. pH Converter PH400G
Cable Length -03 3m
4. Ultrasonic oscillator for ultrasonic cleaning PUS400G -05 5m
-07 7m
5. Solenoid valve For jet or brush PH8MV -10 10m
6. Cleaning pump/tank cleaning only PH8PU1 -15 15m
-20 20m
Only for installation of pH converter Titanium
7. Terminal box PH8TBG Solution -TN
at distance from pH sensor. Ground Tip -HC Hastelloy C
8. Accessories PH8AX
-N Always -N
T10.EPS
-T For PH200/PH400 (*1)
pH Measuring System
d KCl Filling Type pH Sensor -E For PH202 (*2)
Option -B For PH100 (*3)
Model Suffix Code Specifications
Code -G For PH450G,PH202/TB (*5)
KCl Filling Type
PH8EFP pH Sensor Style *A Style A
All Rights Reserved. Copyright © 1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 9
2. Holders
d Guide-pipe Type
Model Suffix Code Option Code Description
PH8HG Guide-pipe (*1)
Option, Mounting Bracket (*2) /MS5 Stainless steel mounting bracket (1 set)
*1 : Pipe length: 2 m
*2 : A set of 2-inch galvanized pipe mounting bracket is provided as standard.
T14.EPS
d Submersion Type
Model Suffix Code Option Code Description
PH8HS Submersion type holder
-PP Polypropylene
Material
-S3 Stainless steel
-10 1.0m
pH Measuring -T Always -T
System
-NN None
-S3 For ultrasonic cleaning (Transducer: SUS316) (*1)
Cleaning -TN For ultrasonic cleaning (Transducer: Titanium) (*2)
System
-HC For ultrasonic cleaning (Transducer: Hastelloy C) (*3)
-JT For jet cleaning. The solenoid valve must be specified separately.
-BR For brush cleaning. The solenoid valve must be specified separately.
-NN None
-C3 3m
-C5 5m
*1: General purpose (Normal pH3 to 14) *2: For salt water *3: For acid (Normal pH0 to 4)
*4: Choose Daielperfrow when this holder is used in organic solvent, high alkali or high temperature alkali.
*5: The required number of mounting bracket sets depends on the installation location and flow rate. In general,
one set is sufficient for pipe lengths of 1 meter, and otherwise two sets are required.
T15.EPS
All Rights Reserved. Copyright ©1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 10
d Flow-Through Type
Model Suffix Code Option Code Description
PH8HF Flow-through type holder
-PP Polypropylene Refer to note below
Material
-S3 Stainless steel for selection
-JPT Rc1
-NPT 1 NPT female thread
-NN None
-JT For jet cleaning. The solenoid valve must be specified separately
-BR For brush cleaning. The solenoid valve must be specified separately
-NN None
-C1 1m
-C3 3m
-C5 5m
Cable Length for
-C6 7m
Ultrasonic Cleaning
-C7 10m
-C8 15m
-C9 20m
-JP Rc1/2
Connector for Jet or
Brush Cleaning -NP 1/2 NPT
*1: General purpose (Normal pH 3 to 14) *2: For salt water *3: For acid (Normal pH 0 to 4)
*4: Choose Daielperfrow when this holder is used in organic solvent, high alkali or high temperature alkali.
Notes:(1) Mounting bracket is generally not required when the stainless steel holder is installed in-line in a pipe
It is required where the holder is installed in a sampling rack (in which case the U-bolt included in /MF1 in not used).
(2) Criteria for material selection (-PP or -S3)
In general, polypropylene is recommended from the viewpoint of chemical resistance. 105
100
However stainless steel is recommend in any of the following cases: *
(a) The liquid contains organic reagent, oxidizing agents, etc., which can attack Stainless Steel
80
polypropylene.
* (b) The temperature/pressure correlation of the process condition falls within the hatched 60
area of the diagram shown right.
(c) The use of polypropylene is not reasonable from a viewpoint of strength or past (8C)
40
experience.
Temperature
All Rights Reserved. Copyright © 1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 11
d pH Holder for High Purity Water 5. Solenoid Valve
Model Suffix Code Option Specifications
Code Model Suffix Code Option Code Description
pH holder for high purity water, PH8MV Solenoid valve
PH8HH wall-mount type
Fluid -A Air
Connection -JPT Inlet; Rc1/4, Outlet; Rc1/2
ports -W Water
-NPT Inlet; 1/4NPT, Outlet; 1/2NPT
Power Supply -100 100V AC
-H Always -H -110 110V AC
voltage
Style *A Style A -200 200V AC
-220 220V AC
Option Mounting Bracket /P Pipe mounting bracket
Power Supply -50 50Hz
T17.EPS
Frequency -60 60Hz
3. Interigent pH Converter Style Code *D Style D
T20.EPS
d 4-Wire Type pH Converter
Option
Model Suffix Code Code Description
PH400G 4-wire pH Converter
Power -1 100/110 V AC, 50/60 Hz
Supply -2 200/220 V AC, 50/60 Hz
Language for -J Japanese
warning, etc -E English
A Always A
*B Style B
Mounting /U Pipe, wall mounting bracket (stainless steel)
hardware /PM Panel mounting bracket (stainless steel)
Hood /H3 Awning hood (carbon steel)
Options /H4 Awning hood (stainless steel)
/X1 Baked epoxy resin
Tag plate /SCT Stainless steel tag plate
Conduit Adapter /AFTG G1/2
/ANSI 1/2 NPT
/SPS Teflon coated SUS steel screws
T18.EPS
All Rights Reserved. Copyright ©1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.22-00
<<Contents>> <<Index>> 12
6. Cleaning Pump / Tank
Model Suffix Code Option Code Description
PH8PU1 Cleaning tank / pump assembly
Power Supply -3 200V AC, 50/60 Hz
-5 100V AC, 50/60 Hz
Style code *B Style B
Options /PT With Rc 1/2 adapter
Cleaning Water Inlet/Outlet /NP With 1/2 NPT adapter
Anchor volts /AN 4 L-shape M12 x 160 (SS41) bolts
Conduit adapter /APUG G 1/2
/ANSI 1/2NPT
T21.EPS
7. Terminal Box
Option Option
Model Suffix Code Specifications Model Suffix Code Specifications
Code Code
PH8TBG Terminal Box PH8TBS Terminal Box
pA Style A -A Always -A
/P Pipe mounting hardware /P Pipe mounting hardware
Mounting hardware Mounting hardware
/W Wall mounting hardware /W Wall mounting hardware
Option Length of special cable u; Standard 03 (3 m), 07 (7 m), Option Length of special cable u; Standard 03 (3 m), 07 (7 m),
(max. 20 m) / C uu (max. 20 m) / C uu 10 (10 m)
10 (10 m)
Adapter for conduit / ATBG Rc 1/2 screw thread Adapter for conduit / ATBG Rc 1/2 screw thread
construction construction
T22.eps T22-1.eps
8. Accessories
9. Consumables
Model Suffix Code Option Specifications
Code Part Name Part Remarks
Number
PH8AX Accessories for pH meter (*1)
General K9142TN One for PH8ERP, PH8EFP, PH8EHP
Calibration -L Two bottles, each containing
250ml solution (pH7 and pH4) purpose K9319NA One for PH8ERP/PF, PH8EFP/PF
Reagents -P 24 bags, each bag containing
Glass High K9142TU One for PH8EFP/HA
powder for 500ml solution
(pH7 X 12 bags and pH4 X 12 electrode alkali K9319NC One for PH8EFP/HA, /PF
bags) and two 500ml
polyethylene bottles. General K9142TH One for PH8ERP, PH8EFP
purpose K9319QA One for PH8ERP, PH8EFP/PF
Style *A Style A
High purity K9142TK One for PH8EHP
water
Option (*2) /STD Sensor stand (with mounting
Junction K9142HW One for PH8ERP/TF, PH8EFP/TF
bracket for 50A 2-inch pipe) Teflon
/KCLL KCl solution (one 250ml K9319QB One for PH8ERP/TF, /PF,PH8EFP/TF, /PF
polyethylene bottle) KCl solution
(3.3mol/l)
K9084LP Six 250 ml polyethylene bottles
/KCLP KCl powder (three bags,
250ml solution each) Buffer solution for
calibration (pH 4) K9084LL Six 250 ml polyethylene bottles
/TMP Thermometer (0 to 100 8C)
Buffer solution for
* 1: Including the following: calibration (pH 7) K9084LM Six 250 ml polyethylene bottles
Two 200ml polyethylene cups Buffer solution for
One cleaning bottle K9084LN Six 250 ml polyethylene bottles
calibration (pH 9)
* 2: Either /KCLL or /KCLP is required for PH8EFP-u-u-TT2. Powder for buffer
K9020XA 12 bags,each for preparation
solution (pH 4) of 500 ml
T23.EPS
Powder for buffer
K9020XB 12 bags, each for preparation
solution (pH 7) of 500 ml
Powder for buffer 12 bags, each for preparation
K9020XC of 500 ml
solution (pH 9)
KCl powder 8 bags, each for preparation
(for PH8EFP, K9020XU of 250ml
PH8EHP)
KCl powder 2 bags, 1 bottle of 3.3 mol/l KCl,
(for PH8ERP) K9142UT 1 syringe
All Rights Reserved. Copyright © 1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 13
WIRING DIAGRAMS
(1) Wiring for pH conveter
PH400G
*3 pH converter
*5
Output signal + mA L1
(4 to 20mA DC) - Power supply
L2
Output signal +
mV
(0 to 1V DC) - *5
Contact
S1
Contact input output S1 High and low
R1 alarms
PH8TBG *1 (cleaning start R2 S2
Contact
Terminal box command) output S2
*5
*2 Contact output S3 (cleaning
PH8ERP S RE S3
T1 or high and low alarms)
PH8EFP GE
PH8EHP T1 T2 FAIL Contact output FAIL (failure)
pH sensor T2 SE
RE GE
SE S
PH400G Converter
51
S3 Power supply Solenoid valve
52
U2
Ultrasonic L1
Vibrator
L2
F05.EPS
All Rights Reserved. Copyright ©1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 14
WIRING USING CONDUIT INSTALLATION
Notes for Conduit Installation
pH converter PH400G
Ultrasonic oscillator Terminal box
PUS400G PH8TBG
(*1)
(a) Recommended conduit installation (adapter not needed)
(*3)
(*6)
F06.EPS
(b) Conduit installation using a conduit adapter
All Rights Reserved. Copyright © 1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 15
DIMENSIONS Unit : mm
KCl refillable KCl filling pH sensor for
pH/ sensor pH sensor pure water
PH8ERP-u PH8EFP-u PH8EHP-u
Medium pressure KCl reserve tank
for KCl filling pH sensor
(with mounting bracket)
(PH8EFP-u)-TT2
Rc 1 / 4
Coupling
with valve
60
Cable length (Standard
10m,15m,20m)
10m,15m,20m)
Cable length
;3m,5m,7m,
;3m,5m,7m,
(Standard;3m,5m,7m,
Tube length
Tube length
10m,15m,20m)
;3m,5m,7m,
(Standard
10m,15m,20m)
f60.5
263
308
88
JIS 2-inch
64
64
64
stanchion
103
103
115
f27.5 f27.5
f38 f38 f27.5
f38
Guide-pipe for submersion type (with mounting hardware)
PH8HG
General purpose KCl reserve tank
Min :110 for KCl filling pH sensor and
Max:515 pH sensor for high purity water
(with mounting bracket)
(PH8EFP-u)-TT1
(PH8EHP-u)-TT1
F07.EPS
85 95
f63
600
JIS 2-inch
stanchion (vertical)
Approx.75 Approx.45
2000 Approx.105
f105
Max:1900
Min :50
Approx.151
7060.2
60
Hole requirements
25
All Rights Reserved. Copyright ©1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 16
Submersion holder — Polypropylene — (See separate drawing for mounting hardware)
Unit:: mm
PH8HS-PP
<Without Cleaner> <With Ultrasonic Cleaner> <With Jet Cleaner> <With Brush Cleaner>
(L: Holder length; 1, 1.5, 2, 2.5, 3 m)
Cable for ultrasonic cleaning
83 (Cable length: 3, 5, 7, 10, 15, 20 m) u 1/2NPT u 1/2NPT
62 42 35 (Code : -NP) 35 (Code : -NP)
44 64
L+31
f51 55 55 55
138.5
75 75 75 F10.EPS
Submersion holder — Stainless steel — (See separate drawing for mounting hardware)
PH8HS-S3
<Without Cleaner> <With Ultrasonic Cleaner> <With Jet Cleaner> <With Brush Cleaner>
(L: Holder length; 1, 1.5, 2, 2.5, 3 m)
Cable for ultrasonic cleaning
u 1/2NPT u 1/2NPT
83 (Cable length: 3, 5, 7, 10, 15, 20 m) 35 35
62 42 (Code : -NP) (Code : -NP)
44 64
u Rc1/2 u Rc1/2
176 176 176
(Code : -JP) (Code : -JP)
42 42 42
f 34 f 22 f 22 f 22
49 49 49
141.0
75 75 75 F11.EPS
All Rights Reserved. Copyright © 1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 17
Mounting hardware for submersion type holder
UNIT: mm
PH8HS.../MS1 1 set
PH8HS.../MS2 2 sets
JIS 2-inch (OD 60.5)
<For Holder without cleaner> 68 64 Stanchion
94 90
54
Max : 515
Sensor Holder
Min : 110
600
Max : 515
Min : 110
f48.6
<For Holder with Cleaner> 95
62
600
130 90
54
100
F12.EPS
Stainless steel hardware for mounting submersion type holder
PH8HS.../MS3 1 set
PH8HS.../MS4 2 sets Max : 500
51 44 48.5
28
55
22 44 44 44 44 44 44 44 22
55 65
600
All Rights Reserved. Copyright ©1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 18
Mounting hardware for submersion type holder Mounting hardware for submersion type holder
— Flange mounting hardware for holder without cleaner — Flange mounting hardware for holder with cleaner
— Material: Polypropylene or Stainless steel — Material: Polypropylene or Stainless steel
74 f290
18
f175 78
L+31
22
Min : 150
Max : L-115
Min : 405
Max : L-130
F14.EPS
Flow-through type holder with mounting hardware PH8HF
fa
(pH Sensor) 4-fD holes
b
c
e
Outlet
O-ring
fB fA
fd
165
h
11061
E
Inlet C
g
f
15061
O-ring
All Rights Reserved. Copyright © 1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 19
Unit : mm
Holder for high purity water PH8HH
Hole dimensions for Holder mounting
60
102 64
20
70
SAMPLE IN
180
171
14 70
Ground connection
SAMPLE OUT terminal M5
70
50
50
35
Rc 1/4 73
27 56 100 100
Sample inlet
15
70 Rc 1/2 148
100 Sample outlet
1/4NPT adapter
120
1/2 NPT adapter F16.EPS
184 220
80
72
144 20
80
144 23 112
36
D: For contact output (S1 and S2)
E: For contact output (S3 and FAIL) Adaptor
49
C D E 38
36 36
All Rights Reserved. Copyright ©1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 20
Pipe Mounting Bracket / Wall Mounting Bracket (option code : /U)
d
Example of bracket used for pipe mounting
188
M6, 4 screws Unit : mm
174
200
50
d
Example of bracket used for wall mounting
224
200
35
15
70
10 mm dia., 3 holes 100 F18.eps
23 M6, 4 screws
12 max.(panel thickness)
137 +20
178
Panel cutout dimensions
F19.eps
All Rights Reserved. Copyright © 1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 21
Ultrasonic oscillator (PUS400G)
Pipe mounting Panel/, Wall mounting
Unit : mm
202 155
162 115 48 162 1 to 10
Panel mounting bracket
50
Hood
110
(optional)
130
180
180
30
30
60
288
151
38 80 3.9 185
206
68
96
Pipe mounting bracket
(optional)
Power supply cable inlet
42 Cable gland DIN PG16 equivalent
68
Ground terminal
96
(M4 screw)
Ultrasonic transducer cable inlet
Cable gland DIN PG16 equivalent
Power supply cable inlet 2-f5.5 holes 100
42 Cable gland DIN PG16 equivalent +1.1 (for hood mounting) 7060.2
Ground terminal 156 0
(M4 screw) 5660.2
Ultrasonic transducer cable inlet 121
8
Cable gland DIN PG16 or equivalent
100
27
2-f6.6 holes 13
+1.1
173 0
185
138
138
5660.2
8
27
27
JIS 2-inch (OD f60.5mm) 2-f6.6 holes
15
stanchion (vertical) (for oscillator
121 mounting) 7060.2
203
48
F20.EPS
71 2-Rc1/2 G1/2
F21.EPS
All Rights Reserved. Copyright ©1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 22
Terminal Box PH8TBG
126 65 48 Unit: mm
30
178
75
254
60.2
Waterproof gland
8
8
7560.2 75
60.2
13
203 185
27
15
48 7060.2 3 - [ 10 hole
F22.eps
Sensor stand
(PH8AX-u)/STD
Sensor (Example)
108
F24.EPS
All Rights Reserved. Copyright © 1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 23
Cleaning Pump/Tank Assembly PH8PU1 Unit: mm
(450)
4-f15 holes
T : Tank 50
V1 : Float valve 1/2 B
V2 : Check valve 1/2 B
V3 : Ball valve
G : Pressure gauge
P : Pump
(442)
(408)
Cleaning
water inlet
Cleaning
G 1/2B water outlet
male(std.) G 1/2B
female(std.)
1/2 PVC
Pipe Teflon braided
horse
Flow diagram
Motor
Cleaning water
Electromagnetic outlet
actuator Cleaning water
inlet
Pump
(800)
Overflow outlet
(16 ATS type)
(804) (138)
F25e.eps
All Rights Reserved. Copyright ©1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 24
SELECTION CRITERIA FOR pH SENSORS AND HOLDERS
<Individual Criteria>
s: Can be used, n:Shortens useful life, x:Cannot be used
Concentration pH * Holder
Chemical
W/V (%) (25 8C) Flow-through,
Guide-pipe
Submersion
Sulfuric acid 0.5 1.0
0.05 2.0
Hydrochloric acid 0.4 1.0
Inorganic acid
0.04 2.0
Nitric acid 0.6 1.0
0.06 2.0
Phosphoric acid 1.0 1.5
Boric acid 0.6 5.0
Carbonic acid 0.6 3.6
Chromic acid 1.2 0.8
Sulfurous acid 0.8 1.4
Acetic acid 0.6 2.8
Organic acid
Aluminous water 5
Zinc chloride 5
Ferric chloride 5
Ferric nitrate 5 1.3
Basic salts
Sodium sulfite 5
Sodium carbonate 5 11.8
Sodium phosphate 5
Potassium chloride 5
Neutral salts
Sodium sulfate 5
Calcium chlorine 5
Sodium nitrate 5 8.2
Aluminum chloride 5
Hydrogen peroxide 1
Oxdizing
1 12.5
agents
Alcohol
Organic
Note: pH values in table are calculated from dissociation constant (including measured value).
T25.EPS
CAUTION
Select the material of wetted parts with careful consideration of process characteristics. Inappropriate
selection may cause leakage of process fluids, which greatly affects facilities. Considerable care must be
taken particularly in the case of strongly corrosive process fluid such as hydrochloric acid, sulfuric acid,
hydrogen sulfide, and sodium hypochlorite. If you have any questions about the wetted part construction
of the product, be sure to contact Yokogawa.
All Rights Reserved. Copyright © 1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 25
Table of Corrosion-Resistant Materials (The data should be used for reference only)
Note: This table shows corrosion resistance for each single substance alone. If a sample contains two or more substances, then the
corrosion resistance may differ from that given in this table.
: Excellent
: Good
: Not so good
X : Unusable Sensor
Holder material Ultrasonic transducer material Seal O-ring
Sensor solution ground tip body
material material
Polypropylene SUS 316 Hastelloy C Titanium Viton Ryton Remarks
Concent’n Temp Judge Concent’n Temp Judge Concent’n Temp Judge Concent’n Temp Judge Concent’n Temp Judge
Chromic acid
20 40 X
10 20 14 30 X 15 43 20 40 5 20
Hypochlorous Acid
10 40 40 X
Hydrobromic acid 40 30 Strong acid
10 20 10 30 10 30 10 100 Weak acid 5 20
Nitric acid 60 X
10 80 10
57 20 57 25 X 57 30
Hydroiodic acid
57 70
3 20 6 30 5 30 5 30 90 20
Sulfuric acid
3 100 5 100 X 5 70 5 100 X 30 90
30 60 15 30 5 30 5 30 85 90
Phosphoric acid
30 100 5 b 5 b 5 60
15 80 10 b 10 b 10 b 15 30
Ammonia water
15 100 28 65 20 65 20 65
10 b 10 b 10 b 10 20
Potassium hydroxide
25 b 25 b 25 b 10 90
Sodium 20 80 20 30 20 30 20 30 10 20
Alkali
sat. 80 25 b 25 b 25 b 25 90
Calcium chloride
sat. 100
20 40 30 b X 30 b X 30 b 20 60
Ferric chloride
20 60
Sodium chloride, 20% 100 90 X 90 X 90 20
+ Saturated Cl2
(Electrolysis solution)
Seawater, Magnesium 24 24 24 24
chloride sat. 80 42 b 42 b 40 b 80
5 60 20 b 20 b 20 b 10 90 Polypropylene may
Nitrates Sulfates
All Rights Reserved. Copyright ©1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 26
Dichloroethare 100 70 X
100 20
Ethyl nitrate 100 105 100 90
100
Carbon tetrachloride 100 20 X 90 b 90 b 100 24 X
Trichloroethylene 100 20 X 100 b 100 b 100 b 100 90 X
Toluene 100 20 X 145 100 90
Benzophenone
100 20
Benzaldehyde 100 70 100 20
100 100 X 100 90 X
Benzyl alcohol
100 20 100 30 100 30 100 25 100 90
benzene
10 70 37 b 37 b 37 b
Fomaldehyde
10 100
Methylnaphthelen
100 20
Methyl ethyl ketone 100 90
70
Methyl alcohol 100 20 100 25 100 25
100 20 100 90 X
Nitrobenzene 100 70
100 100 X
100 20 10 b 10 b
Acetic acid 100 70
100 100 X
100 20 95 30 95 30 95 30 100 90
Phenol
100 100
Benzonic acid 100
100 20 100 20
Motor oil 100 70
100 100
Petroleum ether 100 20 100 20
100 20 101 100 20
Kerosene
100 70 X
10 40 50 100 50 100 50 100
Tartaric acid 10 60
10 80
100 70 100 25 100 180 100 180
Oil and fats
Carbon sulfide 100 20 X 100 25 100 25
Note: "b" refers to the boiling point. T27.EPS
All Rights Reserved. Copyright © 1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
<<Contents>> <<Index>> 27
Enquiry Specifications Sheet for PH400G pH Converter System
For enquires on the Yokogawa pH converter system, please tick (v) the appropriate box u and write down the relevant
information in the blanks.
1 General Information
Company name;
Contact Person; Department;
Plant name;
Measurement location;
Purpose of use; u Indication, u Recording, u Alarm, u Control
Power supply; V AC Hz
2 Measurement Conditions
(1) Process temperature; to Normally [8C]
(2) Process pressure; to Normally [kPa]
(3) Flow rate; to Normally [l/min]
(4) Flow speed; to Normally [m/s]
(5) Slurry or contaminants; u No, u Yes
(6) Name of process fluid;
(7) Components of process fluid;
(8) Others;
3 Installation Site
(1) Ambient temperature;
(2) Location; u Outdoors, u I ndoors
(3) Others;
4 Requirements
(1) Measuring range; u pH 0 to 14 u
(2) Transmission output; u 4 to 20 mA DC u
(3) System configuration selection; u Sensor, u Holder, u pH Converter, u Cleaning system, u Terminal box,
u Accessories
(4) Sensor cable length; u 3m, u 5m, u 7m, u 10m, u 15m, u 20m, u m
(5) Sensor operating pressure; u10 kPa or less, u Greater than 10kPa
(6) Type of holder; u Guide pipe, u Submersion, u Flow-through, u Suspension, u Angled floating ball,
u Vertical floating ball
(7) Cleaning method; u No cleaning, u Ultrasonic cleaning, u Jet cleaning, u Brush cleaning
(8) Sample temperature; u -5 to 1058C, u -5 to 1008C, u -5 to 808C
(9) Others;
All Rights Reserved. Copyright ©1991, Yokogawa Electric Corporation GS 12B7C1-E 6th Edition 2012.11.10-00
Subject to change without notice