Professional Documents
Culture Documents
Procedure
1. Turn on power of CRO
2. Connect function generator with CRO on port Channel 1
3. Adjust x-y axis
4. Apply different wave input through function generator
5. Now rotate time/div switch to adjust frequency and amplitude of a signal
6. You can intense the beam with switch named INTENS
7. You can focus the beam with switch called FOCUS
DR. A P J ABDUL KALAM UNIVERSITY, INDORE
PROCEDURE
1. Power ON the function Generator
2. Connect probe to CRO
3. Select frequency Range from 1kz to 10 mhz
4. Now select type of wave form we need (sin, cos, triangular, saw tooth etc.)
5. Output of function generator can be seen in CRO.
DR. A P J ABDUL KALAM UNIVERSITY, INDORE
Procedure
1. Connect power supply to the instrument
2. Connect ampere meter in series.
3. Connect voltmeter in parallel
4. Now slowly increase the voltage supply from 0V to 12V
5. Now we can see change in both volt and ampere meter
6. Note down the reading and plot the graph.
DR. A P J ABDUL KALAM UNIVERSITY, INDORE
Procedure
1. Supply power to apparatus
2. Connect ampere meter in series.
3. Connect voltmeter in parallel
4. Now slowly increase the voltage supply from 0V to 12V
5. Now we can see change in both volt and ampere meter
6. Note down the reading and plot the graph.
DR. A P J ABDUL KALAM UNIVERSITY, INDORE
Procedure
i. MUX
1. Connect 5V power supply to the apparatus
2. Now give the input to D0 D1 D2 D3
3. Now select the line S1 and S2 (give input 0 or 1)
4. Output can be taken from Z
5. Verify the truth table for mux
ii. DMUX
iii. Connect 5V power supply to the apparatus
iv. Now give the input to D
v. Now select the line S1 and S2 (give input 0 or 1)
vi. Output can be taken from D0 D1 D3 D4
vii. Verify the truth table for Dmux
DR. A P J ABDUL KALAM UNIVERSITY, INDORE
Procedure
1. Externally Connect power supply of 5v to the apparatus
2. Now connect ampere-meter between 2 and 3
3. Connect wire between 4 and 5
4. Connect voltmeter between 1 and ground
5. Connect another voltmeter between 6 and ground
6. Now plot V-I characteristic
DR. A P J ABDUL KALAM UNIVERSITY, INDORE
Procedure
1. Externally Connect power supply of 5v to the apparatus
2. Now connect ampere-meter (Ie) between 2 and 3
3. Connect another Ampere-meter (Ib) between 4 and 5
4. Connect voltmeter (Ve) between 1 and ground
5. Connect another voltmeter (Vbb) between 6 and ground
6. Now plot V-I characteristic
DR. A P J ABDUL KALAM UNIVERSITY, INDORE
Procedure
1. Externally supply 12 v and 5 v to the apparatus
2. Connect voltmeter between 1 and ground
3. Connect ampere meter between 3 and 4
4. Connect second voltmeter between 2 and ground
5. Plot the V-I characteristic by using a variable potentiometer.
DR. A P J ABDUL KALAM UNIVERSITY, INDORE
Procedure
1. Connect power supply of 5v and 12 v respectively
2. Connect voltmeter between 1 and ground
3. Connect ampere meter between 2 and 3
4. Now connect second ampere meter between 4 and 5
5. Connect second Voltmeter between 6 and ground
6. Plot V-I characteristic by using variable potentiometer
DR. A P J ABDUL KALAM UNIVERSITY, INDORE
Procedure
1. Connect 5V and Ground to their indicated position on DB02 from External
DC power supply or from DC power block of Digital IC Trainer Scientech
2611
2. Connect input 00, 01, 10, 11 to pin x and y of OR gates. Switch on the
Power on the Power Supply.
3. Observe output Z of gates on multimeter or on logic probe or on LED
display of digital IC trainer Scientech 2611 and prove truth table.
DR. A P J ABDUL KALAM UNIVERSITY, INDORE
Procedure
1. Connect 5V and Ground to their indicated position on DB02 from External
DC power supply or from DC power block of Digital IC Trainer Scientech
2611
2. Connect input D0-D7 to 8*3 encoder circuit
3. Observe the output X Y Z on Digital IC Trainer Scientech 2611
4. Connect Inputs X Y Z to 3*8 decoder circuit
5. Observe output D0-D7 on Digital IC Trainer Scientech 2611
6. Verify truth table
DR. A P J ABDUL KALAM UNIVERSITY, INDORE
Procedure
1. Connect 5V and Gnd to the device
2. Connect logic 1 to CP and MS input
3. Clear output Q0-Q3 by connecting logic 0 (gnd) to MCD input
4. Check output it will be 0 0 0 0.
5. Connect logic 1 to CP, MS and input MCD. Observe output
6. Connect logic 0 to CP input. Observe output
7. Make CP Terminal to Transit from 1 to 0 and observe next state of counter
8. Repeat step until last state 1111 appear.
DR. A P J ABDUL KALAM UNIVERSITY, INDORE
Procedure
1. Connect +35V and +15V and Ground to the apparatus
2. Make sure potentiometer P1 and P2 are zero
3. Connect ammeter to point 1 and 2 to indicate current Ia
4. Connect voltmeter Va to point 3 and gnd
5. Connect ammeter to point 4 and 5 to indicate current Ig
6. Connect voltmeter Vg to point 6 and gnd
7. Now rotate potentiometer to get reading on voltmeter and ammeter. Plot
graph between Va and Ia
DR. A P J ABDUL KALAM UNIVERSITY, INDORE
Procedure
1. Connect 5V and Ground to the apparatus
2. Connect B0, B1, B2, B3 as per truth table to binary to gray code
3. Observe output G0, G1, G2, G3 on Digital Lab Scientech 2611
4. Repeat above step for remaining inputs and prove truth table
5. Repeat above steps for gray to binary code convertor and prove truth table
DR. A P J ABDUL KALAM UNIVERSITY, INDORE
Procedure
1. Connect +35V and -35V DC power supply to apparatus
2. Set potentiometer P1 and P2 to zero
3. Connect voltmeter Va to point 3 and ground
4. Connect ammeter Ia between point 1 and 2
5. Put switch on +35V and vary potentiometer
6. Plot curve between +Va and Ia
7. Switch off power supply. Put switch towards -35V
8. Plot curve between –Va and –Ia
DR. A P J ABDUL KALAM UNIVERSITY, INDORE
Procedure
DR. A P J ABDUL KALAM UNIVERSITY, INDORE
AIM: Common Emitter Amplifier Characteristic
DIAGRAM
DR. A P J ABDUL KALAM UNIVERSITY, INDORE
Procedure
DR. A P J ABDUL KALAM UNIVERSITY, INDORE