Professional Documents
Culture Documents
Plant ID Plant
Equipment Number: 5
Equipment Name:
Equipment Type:
Date: 07/05/19
Piping Classification
Piping Spec & Grade: C4 API 5L X42
Pipe Schedule: 4" CED 40
Nominal Thickness: 0.237 in
Design Conditions: 480.038 psig, -20⁰ F to 150⁰ F
Design Code: ASME B.31.8
P&ID Dwg:
Pressure design wall thickness (t)
Reference: ASME B31.8-2012, 841.1.1 (a)
PD
P = 2St FET t = 2SFET
D
where
D = nominal outside diameter of pipe, inches
E = longitudinal joint factor
F = design factor
P = design pressure, psig
S = specified minimum yield strength, psi
T = temperature derating factor
t = pressure design wall thickness, inches
S= 42000 psi
D= 4.5 in
F= 0.4
E= 1
T= 1
P= 480.037725 psi
t= 0.064 in 1.6 mm
t = t+A
where n
tn = pressure design wall thickness + A, inches
A = corrosion allowance
t= 0.064 in
A= 0.05 in
tn = 0.114 in 2.9 mm PROPUESTO = 6.02 mm
ASME B31.8 Minimum Allowable Wall Thickness Calculation (Operating Conditions) Page 1 of 1
Plant ID Plant
Equipment Number: 5
Equipment Name: 0
Equipment Type: 0
Date: 07/05/19
Piping Classification
Piping Spec & Grade: C4 API 5L X42
Pipe Schedule: 4" CED 40
Nominal Thickness: 0.237 in
Operating Conditions: 384.03
Design Code: ASME B.31.8
P&ID Dwg: 0
Pressure design wall thickness (t) for MAOP
Reference: ASME B31.8-2012, 841.1.1 (a)
PoD
Po = 2St FET t = 2SFET
D
where
D = nominal outside diameter of pipe, inches
E = longitudinal joint factor
F = design factor
Po = maximum allowable operating pressure (MAOP), psig
S = specified minimum yield strength, psi
T = temperature derating factor
t = pressure design wall thickness, inches
S= 42000 psi
D= 4.5 in
F= 0.4
E= 1
T= 1
Po = 384.02991 psi
t= 0.051 in 1.3 mm
tn = t + A
where
tn = pressure design wall thickness + A, inches
A = corrosion allowance
Percentage wall thickness remaining
t= 0.051 in T-nominal 0.237 in
A= 0.05 in T-actual: 0.101 in
tn = 0.101 in 2.6 mm % T-Remaining: 43 %
ASME B31.8 Design Pressure Calculation Page 1 of 2
(MAOP based on actual minimum corroded thickness)
Plant ID: Plant
Equipment Number: 5
Equipment Name:
Equipment Type:
Date: 5/7/2019
Piping Classification:
Piping Spec & Grade: C4 API 5L X42
Pipe Schedule: 4" CED 40
Nominal Thickness: 0.237 in
Design Conditions: 480 psig, -20⁰ F to 150⁰ F
Design Code: ASME B.31.8
P&ID Dwg:
Calculation MAOP
Reference: ASME B31.8-2012, 841.1.1 (a)
Steel Pipe Design Formula:
P = 2St
D FET
where
D = nominal outside diameter of pipe, inches
E = longitudinal joint factor obtained from Table 841.1.7-1
F = design factor obtained from Table 841.1.6-1
P = design pressure, psig
S = specified minimum yield strength, psi
T = temperature derating factor obtained from Table 841.1.8-1
t = nominal wall thickness, inches
ASME B31.8-2012, Table 841.1.8-1 Temperature Derating Factor, T, for Steel Pipe
Temperature
Temperature, °F (°C) Derating Factor, T
Design Factors and Test Pressures in the US Regulations: 49 CFR 192 requires the factor to be 0.50 for risers
Page 1 of 1
Temperature Derating
Temperature, °F (°C) Factor, T
250 (121) or lower 1
300 (149) 0.967
350 (177) 0.933
400 (204) 0.9
450 (232) 0.867
GENERAL NOTE: For intermediate temperatures, interpolate for derating factor
factor
ASME B31.8-2012, MANDATORY APPENDIX D
SPECIFIED MINIMUM YIELD STRENGTH FOR STEEL PIPE COMMONLY USED IN PIPING SYSTEMS
Table D-1 Specified Minimum Yield Strength for Steel Pipe Commonly Used in Piping Systems
Spec. No. Grade Type [Note (1)] SMYS, psi SMYS, (MPa)
GENERAL NOTE: This table is not complete. For the minimum specified yield strength of other
grades and grades in other approved specifications, refer to the particular specification.
NOTES:
(1) Abbreviations: BW = furnace buttwelded; DSA = double submerged-arc welded; EFW = electric
fusion welded; ERW = electric resistance welded; FW = flash welded; S = seamless; LW = laser
welded.
(2) Intermediate grades are available in API 5L.
(3) See applicable plate specification for SMYS.