Professional Documents
Culture Documents
Keywords: Ericsson engine, Joule cycle reciprocating engine, external heat supply engine, hot air engine.
Abstract
The “hot air engines” family includes two subgroups: the Stirling engines, which have no valves, and the Ericsson
engines with valves in order to close the cylinders during the compression or the expansion processes. So, an Ericsson
engine is an external heat supply engine working according to a Joule thermodynamic cycle. It is based on reciprocating
piston-cylinder machines. Such engines are especially interesting for low power solar energy conversion and micro-
CHP from conventional fossil fuels or from biomass.
A prototype has been designed to work with air in open cycle as the working fluid. The nominal pressure ratio is 3 and
the maximum operating temperature is 650 °C. The prototype expansion cylinder capacity is 0.65 dm3. The expansion
cylinder bore is 80 mm, the piston stroke is 129 mm and the maximum rotation speed is 750 rpm. While designing the
prototype, it has been chosen to have a single cylinder with a double-acting piston. The upper face of the piston closes
the expansion space, while the lower face of the piston delimits the compression space. The double-acting piston is
connected to a double contra-rotating crankshaft.
Different innovative solutions have been introduced in the mechanical design of the prototype. The main difficulty in
the design of a high temperature difference Ericsson engine consists in the hot part of the engine with the inlet and
exhaust valves of the expansion cylinder. The technology used to guide the valves rods with a high degree of accuracy,
the method used to cool different parts of the engine and to cope with differential dilatation are reported. Some
preliminary experimental results are presented.
1. Introduction
A special family of thermal engines can be identified from the following features: reciprocating engines, external
heat supply, separate compression and expansion cylinders, regenerator or recuperator, monophasic gaseous working
fluid [1]. These engines are sometimes called ‘hot air engines’ [2], even if the air used in the XIXth century engines has
been replaced by high pressure hydrogen or helium in a lot of modern engines. Hot air engines have known commercial
success during the XIXth century [3], but, since the beginning of the XXth century, they have been discarded and
replaced by internal combustion engines or electric motors. The family of hot air engines is divided in two subgroups:
the Stirling engines, invented in 1816, have no valves (Fig. 1,a) whereas Ericsson engines, invented in 1833 (Fig. 1,b)
have valves in order to isolate the cylinders.
The valves give some advantages to the Ericsson engine [1]. Amongst them, the most important one is that the heat
exchangers are not to be considered as unswept dead volumes whereas the Stirling engine designer is faced to the
difficult compromise between heat exchanger transfer area maximization and heat exchanger volume minimization. The
theoretical Ericsson cycle with two isobaric processes and two isothermal processes is not suited to describe the
Ericsson engine. Indeed, the lack of heat transfer area in the cylinders leads to equip the engine with heat exchangers
outside the cylinders in order to exchange heat with the hot and the cold sources. So the Joule cycle with two isentropic
and two isobaric processes is better suited to describe the Ericsson engine. This cycle is also often used for gas turbines.
*
Corresponding author. Tel.: +33 5 59 40 71 24; fax: +33 5 59 40 71 25
E-mail address: pascal.stouffs@univ-pau.fr
Since the pioneer work of the Philips company, around the second world war, the attention has been drawn on
Stirling engines and lots of research and developments have been carried out. However, up to now, not many studies are
dedicated to Ericsson engines. There are some references to internal combustion Ericsson engines [4−5] instead of
external heat supply. The studies dealing specifically with external heat supply Joule cycle reciprocating engines are
limited [6−8]. The studies reporting experimental results are rare [9−10].
Regarding the Ericsson engine modeling, a comparison of the respective advantages and disadvantages of the Joule
cycle Ericsson engine and the Rankine cycle steam engine has been drawn [11] and it has been shown that the operation
of Ericsson engine according to the so-called “humid cycles” is not interesting as soon as heat recovery Joule cycles are
considered [12]. An energy, exergy and cost analysis has demonstrated that the Ericsson engine is suited for micro-
cogeneration applications [13]. A dynamic simulation model shows how the Ericsson engine responds to perturbations
and transients [14] allowing to design an appropriate control system. Finally studies have been devoted to the global
effect of the in-cylinder heat transfer on the energy performance of the Ericsson engine and the interest or no to promote
these transfers [15] or to the modeling of the instantaneous fluid to wall in-cylinder heat transfer [16].
A cycle with an internal heat recovery exchanger R has been chosen because it is well known that if the recuperator
R effectiveness is large enough such cycles can lead to much higher thermal efficiency than non recuperated cycles,
with very low pressure ratio. It is anticipated that a low pressure ratio together with the atmospheric pressure as
minimum pressure will lead to a technologically simpler engine but at same shaft power, the low pressure engine will
be much larger and heavier than the corresponding non recuperated high pressure and/or pressurized engine. As
stationary applications are considered, this has been considered as a minor inconvenience.
So the expansion cylinder of the prototype has been designed to withstand a maximum pressure of 300 kPa. The
maximum temperature at the heater outlet Th is set to 650 °C as well as for material reason as for affordable heater
temperature in the solar or biomass application considered.
As the pressure ratio is low the net mechanical power produced by the engine, that is the difference between the
mechanical power produced by the expansion cylinder and the mechanical power consumed by the compression
cylinder, is also low compared to the expansion cylinder power. It is thus very important to achieve a very high
mechanical efficiency. That is why a configuration with a single double-acting cylinder has been chosen. The lower
face of the piston makes the compression while the upper face makes the expansion. So the shortest and the most
efficient link is obtained between the device producing and the device consuming the mechanical power and only the
net mechanical power is transferred to the shaft.
*
Corresponding author. Tel.: +33 5 59 40 71 24; fax: +33 5 59 40 71 25
E-mail address: pascal.stouffs@univ-pau.fr
Piston rod
3. Mechanical design
The mechanical design of the Ericsson engine has led to several innovations that have been experimentally
validated. All these innovations are deliberately presented in order to be in the public domain. So the prototype
presented here is a free technology Ericsson engine.
The expansion cylinder valves are one of the most difficult points. Figure 5 shows how they have been realized.
The commercial poppet valves are clipped on a hollow tube extension in which cooling water is allowed to flow.
Thanks to the anti-radiation shields and the cooling water flow, the upper part of the valve casing and valve extension
rod is at ambient temperature while the valve itself is at the maximum temperature of 650 °C. The guidance of the valve
has to be very accurate. A linear ball guidance is used. Figure 6 is a picture of the envelope casing of the valve, the ball
casing and the valve extension tube. The guidance sets of the admission and the exhaust valve are only linked by the
cylinder head so that they are allowed to move according to the dilatation of the spacing of their seats on the cylinder
head. The valves that are guided in the cold part of the casing are thus always centred on their seats in the hot part of the
cylinder.
*
Corresponding author. Tel.: +33 5 59 40 71 24; fax: +33 5 59 40 71 25
E-mail address: pascal.stouffs@univ-pau.fr
Hollow rod
Ball
20°C housing
Water flow inlet
Cylinder head
650°C
Fig. 5 Hot valves of the expansion space Fig. 6 Hot valve ball guidance
The actuation of the valves is achieved by means of cams made up of two superimposed half-cams whose angular
position can be adjusted on the camshaft. By this way the opening angle and duration of the valve can be manually
varied (Fig. 7). This adjustment is not necessary for an engine operating with always the same expansion space inlet
temperature.
The rocking arm is equipped with a roller which is in contact with the cam. On the other side of the rocking arm the
motion is transmitted to the valve rod by means of a blade inserted into grooves made in the arm and in the clip fixed on
the valve rod (Fig. 8). This blade slightly oscillates to compensate the difference between the motion in circular arc of
the rocking arm and the purely linear motion of the valve. The radiuses at the ends of the blade are smaller than the
radius of the grooves so that the blade is allowed to roll without slipping in the grooves (Fig. 9). The radial force
component on the ball guide is negligible and the mechanical losses are negligible too.
*
Corresponding author. Tel.: +33 5 59 40 71 24; fax: +33 5 59 40 71 25
E-mail address: pascal.stouffs@univ-pau.fr
The low power to cylinder capacity ratio of the Ericsson engine prototype leads to other choices than the usual
internal combustion engine piston rings. Indeed with usual rings the friction losses could be prohibitive and could
prevent the engine from operating. It is of the utmost importance to maximize the mechanical efficiency of the engine.
A mechanical efficiency of 87% has been measured on the prototype [9]. The piston rings are made up of two parts. The
metal core has the function of providing a plating on the cylinder liner by elastic deformation and a polymeric coating
material ensures the sealing friction. Different solutions are possible for the connection between the elastic ring and the
friction ring: gluing, molding, mechanical interlocking by grooving, etc... The junction between both ends of the friction
ring has to maintain air tightness in this flexible zone. It has been realized with a flexible and sticky material. A silicone
sealant polymerized after application has been used (Fig. 11).
The compression space is located under the piston in the annular space between the cylinder liner and the piston
rod. Both oscillating valves are driven by a set of cam, rocking arm and connecting rod. Large flow areas lead to
negligible pressure losses. A cam is fitted on each crankshaft (Fig. 12).
*
Corresponding author. Tel.: +33 5 59 40 71 24; fax: +33 5 59 40 71 25
E-mail address: pascal.stouffs@univ-pau.fr
Compression
space inlet flange
Rod
Annular water flow
Rocking arm
Cam
Double contra-
rotating
crankshaft
Oscillating valve
The compression space is located under the piston in the annular space between the cylinder liner and the piston
rod. Both oscillating valves are driven by a set of cam, rocking arm and connecting rod. Large flow areas lead to
negligible pressure losses. A cam is fitted on each crankshaft (Fig. 12).
4. Experimental setup
Figure 13 presents a sketch of the Ericsson engine. In normal engine operation, the air which acts as the working
fluid of the engine is taken from the environment through the filter F. It passes through the flowmeter DEB then enters
the compression space (in cyan). After compression, the air receives heat from the heat recovery “recuperator”
exchanger RST1 and from the electrical heater REH. A buffer tank RST2 is inserted in the circuit before the expansion
space. Afterwards the expanded air gives heat to the compressed air in the recuperator HS before being discharged to
the atmosphere.
(a) (b)
Fig. 14 Instantaneous temperature sensor: (a) probe; (b) enlargement on the thermocouples
2.6
3
2.4
P Cylinder P Cylinder
2.2 P Exhaust pipe P Inlet pipe
P Inlet pipe 2.5 P Exhaust pipe
Pressure [bar]
Pressure [bar]
1.8 2
1.6
1.5
1.4
1.2
1
1
0.8 0.5
0 0.5 1 1.5 2 2.5 3 3.5 0 1 2 3 4 5 6 7 8
Volume [m3] x 10
-4 Volume [m3] x 10
-4
Fig. 15 Compression space indicated diagram Fig. 16 Expansion space indicated diagram
Copyright © 2014 by ISEC International Stirling Engine Committee. All right reserved.
Figure 16 presents an example of the instantaneous temperature measurement by one of the sensor in the
compression cylinder head. The green curve correspond to the thinner thermocouple of 12.5 µm while the cyan line
whose amplitude is lower due to the thermal inertia of the thicker wire is the temperature registered by the 25 µm
thermocouple.
40
30
20
10
0
0 45 90 135 180 225 270 315 360
Crankshaft angle [°]
Fig. 16 Example of measurement registered by one of the instantaneous temperature sensor in the
compression space
6. Conclusions
A prototype of Ericsson engine has been designed and built. It is now in a phase of test. The engine is designed to
operate with air in open cycle as the working fluid. The maximum temperature is 650 °C. As heat recovery is
considered the pressure ratio is low and the maximum pressure at the expansion cylinder inlet is 300 kPa.
The technological choices that led to the prototype design are presented and justified and some free technology
innovations are illustrated. The experimental setup is presented together with some examples of measurements. The
Ericsson engine prototype is now in a phase of adjustment before an extensive test campaign.
Acknowledgement
The design and the building of the prototype have been made possible thanks to a partnership with France Télécom,
and grants from the Energy Program of the French ‘Centre National de la Recherche Scientifique (CNRS)’ and from the
SEED Program of the French ‘Agence Nationale de la Recherche (ANR)’.
References
[1] Stouffs P. Hot Air Engines. Journal of Applied Fluid Mechanics 2011, 4, 1−8.
[2] Finkelstein Th, Organ AJ. Air engines. Professional Engineering Publishing Ltd, London, 2001.
[3] Kolin I. Stirling motor. Zagreb Univ. Publications Ltd, Zagreb, 1991.
[4] Bell MA, Partridge T. Thermodynamic design of a reciprocating Joule cycle engine. Proc. Instn Mech. Engrs, Part
A, J. Power & Energy 2003, 217, 239−246.
[5] Moss RW, Roskilly AP, Nanda SK. Reciprocating Joule-cycle engine for domestic CHP systems. Applied Energy
2005, 80, 169–185.
Copyright © 2014 by ISEC International Stirling Engine Committee. All right reserved.
[6] Wojewoda J, Kazimierski Z. Numerical model and investigations of the externally heated valve Joule engine.
Energy 2010, 35, 2099–2108.
[7] Creyx M, Delacourt E, Morin C, Desmet B, Peultier P. Energetic optimization of the performances of a hot air
engine for micro-CHP systems working with a Joule or an Ericsson cycle. Energy 2013, 49, 229−239.
[8] Kussul E, Makeyev O, Baidyk T, Olvera O. Design of Ericsson Heat Engine with Micro Channel Recuperator.
ISRN Renewable Energy 2012, Article ID 613642, 8 p.
[9] Touré A, Stouffs P. First Test Results of a Small Joule Cycle Ericsson Engine Prototype for Solar Energy
Conversion or for Micro-CHP Application. Proceedings of ECOS 2010, EPFL, Lausanne, June 14−17, 2010.
[10] Touré A. Etude théorique et expérimentale d’un moteur Ericsson destiné à la microcogénération. Thèse de
l’Université de Pau et des Pays de l'Adour, 18 novembre 2010.
[11] Ibsaine R, Sène Ph, Stouffs P. Moteurs Volumétriques Alternatifs à Apport de Chaleur Externe : Comparaison
entre les Machines à Cycle de Joule et les Machines à Cycle de Rankine. Actes du Colloque COFRET, Sozopol,
Bulgarie, 11−13 mai 2012.
[12] Ibsaine R, Stouffs P. Modeling of a humid air reciprocating regenerative Joule cycle Ericsson engine. 15th
International Stirling Engine Conference (ISEC), Dubrovnik, Croatie, September 27−29, 2012.
[13] Bonnet S, Alaphilippe M, Stouffs P. Energy, exergy and cost analysis of a micro-cogeneration system based on an
Ericsson engine. Int. J. Therm. Sci. 2005, 44:12, 1161−1168.
[14] Lontsi F, Hamandjoda O, Fozao K, Stouffs P, Nganhou J. Dynamic simulation of a small modified Joule cycle
reciprocating Ericsson engine for microcogeneration systems. Energy 2013, 63, 309−316.
[15] Fula Rojas A, Sierra Vargas F, Stouffs P. Étude paramétrique globale de l'influence des transferts thermiques au
travers des parois des cylindres d'un moteur Ericsson, CIFEM 2012, ART-10-52, Ouagadougou, Burkina Faso, 2−4
mai 2012.
[16] Fula A, Stouffs P, Sierra F. In-Cylinder Heat Transfer in an Ericsson Engine Prototype, Renewable Energy and
Power Quality Journal 2013, 11, paper 594.
[17] Alaphilippe M, Stouffs P. Instantaneous and yearly electric production of a low power thermodynamic solar
energy conversion system: modeling results. Proceedings of the 21st ECOS. A. Ziebik, Z. Kolenda, W. Stanek, eds,
Cracow-Gliwice, Poland, 2008,3, 1161−1168.
Copyright © 2014 by ISEC International Stirling Engine Committee. All right reserved.