CAM TIMING KIT JAGUAR / LAND ROVER 3.2, 3.5, 4.0, 4.2 & 4.4 V8 gas engines Models:Jaguar: XJ, S-Type, XK, XF / Land Rover: New Range Rover(LM), Range Rover Sport(LS), Discovery III (LA) AS4980...................................................................CAM TIMING KIT CRANKSHAFT PULLEY REMOVER/INSTALLER TOOL SET. These tools must be used together when removing the crankshaft pulley. This Holding Tool is also used to counter-hold the crankshaft pulley during installation. AS4985..............................................CRANKSHAFT HOLDING TOOL CRANK PULLEY PULLER Use to remove crankshaft pulley and to simulate the timing damper oil pressure.
JAG1436A…………………………………CRANK PULLEY PULLER
CYLINDER HEAD SOCKET Specially shaped 11/16” socket allows easy access to difficult cylinder head bolts. Models: Series III, XJS, XJ40, X300, V12 H4101…………….………….TIMING CHAIN TENSION RETAINER CAMSHAFT SPROCKET RETAINER Models Series III, XJS, XJ40, X300
JAG040…….…………………..CAMSHAFT SPROCKET RETAINER
CHAIN LINK PRESS
Installs pressed master links on timing chain. Models: XJS, XJ40
000-5843……………………………………CHAIN LINK PRESS
DISTRIBUTOR POSITIONING GAUGE Use to set proper alignment of distributor during installation.
JAG189……………………..DISTRIBUTOR POSITIONING GAUGE
ENGINE SUPPORT BRACKET
Supports engine from above when transmission or mounts are worked on. Models Series III, XJS, XJ40, X300
10-222A……………………………….ENGINE SUPPORT BRACKET
JACK SHAFT SPROCKET HOLDER Models: XJS, XJ40, V12
JAG039…………………………..JACK SHAFT SPROCKETHOLDER
SPARK PLUG SOCKET
Special low profile spark plug socket to remove difficult to reach plugs on. Models: Series III, XJS, V12
JAG1364……………………………………..SPARK PLUG SOCKET
SPARK PLUG WIRE PLIERS Allows easy removal of tough to reach spark plug wires on all late model automobiles. Wide grip section and special angle make it easy to remove plug wires without separating or damaging connectors, wires or shields. 103-0037…………………………………SPARK PLUG WIRE PLIERS RADIATOR RESERVOIR ADAPTER Use to adapt standard radiator pressure tester, such as Stant or Blue Point to threaded reservoir. Models: All threaded Reservoirs. FZ34…………………………….RADIATOR RESERVOIR ADAPTER TORQUE ANGLE GAUGE Angle gauge with magnetic base allows accurate torquing of ‘stretch’ type bolts when a torque value and torsion angle are specified. Models: XJS 3.6 ST7380……………………………………TORQUE ANGLE GAUGE STEERING RACK MOUNT BUSHING DRIVER Use to remove and install the metal clad steering rack mount bushings Models: XJS, Series III
JAG003…………..STEERING RACK MOUNT BUSHING DRIVER
BRAKE RESERVOIR DAPTER Allows quick bleeding of brake lines with a standard power bleeder. Models: TEVES Brakes
JAG004……………………………BRAKE RESERVOIR ADAPTER
TIE ROD BALL JOINT PRESS Use to remove ball joints without damaging rubber boots. Models: All
KK129-1………………………….TIE ROD BALL JOINT PRESS
REAR CAMBER SETTING LINKS
Use to position rear end during camber adjustment.
JAG025B…………………..REAR CAMBER SETTING LINKS
TERMINATOR SUPER LOGIC PROBE The Terminator is a superior Logic probe combining the features of a DMM and oscilloscope but simplifying the display. Particularly useful for tracing CAN signals. BT7205J..................................TERMINATOR SUPER LOGIC PROBE 1570/2 - Universal set KABELEX® Content: No 1501, 1502, 1505: ejection tools for contact sizes Diameter in mm 1.5; 3.5; 2.3 mm No 1511, 1512, 1515: dismantling sleeves for contact sizes Diameter in mm 1.5; 3.5; 2.3 mm No 1553: cable extractor tool for plugs with one release channel flat contacts 2.8 and 5.8 mm No 1556: cable extractor tool for Micro-Timer II, III contacts flat contacts 1.6 mm No 1559: cable extractor tool for Maxi-Power Timer contacts flat contacts 9.5 mm No 1562: cable extractor tool for Pit-Pod contacts No 1574: cable extractor tool for Micro-Timer I contacts and ABS plug-in housing flat contacts 1.6 mm No 1591: cable extractor tool for plugs with two release channels flat contacts 2.8 and 5.8 mm