Professional Documents
Culture Documents
, MT
Soal I.
A well is being planned in an area that requires protection of shallow freshwater sands.
Local regulations required the surface casing shoe to be at least 200 ft below the deepest
freshwater sand above 1,500 ft and the top of cement to be at least 100 ft above the shallowest
freshwater sand. Use the following assumptions in your calculations. A 20-inch hole will be
drilled to the minimum depth required by regulation and 16-inch casing (65 lbm/ft) will be
run to TD. The openhole caliper logs from offset wells indicate 20% excess will be required
in the cement volume to accommodate washouts. The float collar will be run 80 ft above the
float shoe. Class C cement weighing 14.8 lbm/gal Refer to the log strip shown below and
having a yield of 1.32 cu ft/sack will be used and circulated back to surface. Which is a
composite from offset wells, to evaluate the required casing depth.
Soal II.
Soal III.
The following information is provided regarding expected pressure for various hole
intervals:
A trip margin of 0.2 lbm/gal must be maintained during all intervals. Calculate the
minimum drilling fluid density required when intermediate casing is run.
Soal IV.
A well is drilling ahead at 10,000 ft MD (9,000 ft TVD) with a BHA comprised of 400 ft
of 8-in x 3-in drill collars (147 lb/ft) and 4 1/2-in, 16.60 lb/ft drill pipe (18.40 lb/ft
adjusted weight). A bit trip is required. Assume there is no fluid lost to the formation
and the drill string is pulled dry (i.e., there is no loss of fluid at the surface). Calculate the
total volume (barrels) of drilling fluid required to keep the hole full while tripping
completely out of the hole is most nearly
.
.
Soal V.
Batch drilling#1 hole section 12.25” MW 11.1ppg, RPM 1200 ROP 120ft/min, FL 150gpm
kedalaman 10000’ terjadi Differential Sticking sepanjang 2stand diatas Jar, diketahui
Pf=4000psi, ID DP 4”, berapakah nilai Differential Force? .c), setelah pipa terjepit dapat
teratasi dengan metode Jarring, operasi pemboran dilanjutkan dan menembus formasi dengan
tekanan tinggi, Apakah tanda–tandanya? .d), sehingga terindikasi terjadi Kick, Apa yang
dimaksud dengan Kick? .e), Selanjutnya, Langkah dan Prosedur apa yang harus saudara
lakukan apabila telah mengetahui adanya Kick? .f), Setelah anda melakukan prosedur tutup
sumur, anda diharuskan menentukan metode mana yang cocok untuk mematikan sumur, Sebut
dan jelaskan beberapa metode mematikan sumur! .g), pada saat observasi posisi pahat
tidak berada di dasar lubang atau yang disebut Top Kill, Apa yang dimaksud dengan istilah
Top Kill dan jelaskan metode Top Kill! .h). Dengan teknik Bleed Off, saudara diinstruksikan
untuk menghitung perubahan tekanan 100 psi equivalent dengan data dia.bit 12.25”, OD DP
5”, TVD 10800’, hitung perubahan tekanan 100 psi equivalent? .i). Karena Kick terjadi
tidak didasar lubang maka salah satu jalan untuk mematikannya adalah berusaha untuk
memasukkan kembali rangkaian pemboran sampai kedasar lubang kembali. Dalam pemboran
saat mencabut rangkaian terjadi Kick, saat Kick telah tercabut 20 stand DrillPipe dan
diputuskan oleh Saudara sebagai Field Drilling Engineer untuk melakukan stripping in,
Data
SIDPP 1200 psi
SICP 1800 psi
Pit Gain 20 bbl
Casing 13-3/8"@5000'
DP 5", 19,5 lbs/ft
DC 6,75', 333,05'
Lakukanlah perhitungan persiapan; j.) Gradient lumpur, k.) Tekanan Hidrostatik per
bbl lumpur @ open hole, @annulus Drill Collar dan @annulus DrillPipe, l). Setelah
operasi stripping dilaksanakan, batch drilling hole section 12.25” terjadi masalah yang sama
yaitu Kick, diberikan data pada tabel MAASP (Maximum Allowable Annular Shut-In
Pressure), isilah kolom – kolom yang kosong, m). Dan selanjutnya hitung dan plot grafik
2600
2500
2400
2300
2200
2100
2000
1900
1800
1700
1600
DP Pressure
1500
1400
1300
1200
1100
1000
900
800
700
600
500
400
300
200
100
0
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400
Strokes