Professional Documents
Culture Documents
v1.60CTF4.D2R firmware.
We will start by establishing a point-to-point routing for LAN-to-LAN and then will
apply a default gateway for Internet Access.
IP Address: 192.168.0.X
Net: 255.255.255.0
IP Address: 192.168.1.X GW: 192.168.0.254
Net: 255.255.255.0
GW: 192.168.1.1
Here is a complete step by step setup procedure for the Remote Office LAN,
SDTU01 Router. (HyperTerminal connection to serial port).
System start...
>> quick #enter the quick setup wizard
R1483(r)/ IPoA(i)/ PPPoA(p) / PPPoE(pe) : I #choose IP over ATM
1
>> Setup Configuration
FUNCTION: IPOA
Ethernet IP: 192.168.1.1
Subnet Mask: 255.255.255.0
# VPI VCI WAN IP Gateway IP
1: 8 32 10.1.1.2 10.1.1.1
>> rtable
> rtable> deliproute all #clear out the routing table
> rtable> addiproute 0.0.0.0 0.0.0.0 10.1.1.1 #add the route
> rtable> home
>> save
Saving configuration...Configuration saved.
Updating flash filing system ...
System start...
>>
>>
Here is a complete step by step setup procedure to enable DCHP server for the
Remote Office LAN, SDTU01 Router. (HyperTerminal connection to serial port). In
the example we open up 100 IP addresses for Dynamic Host Configuration and
add two Domain Name Server addresses.
>> lan
> lan> dhcpserver 192.168.1.10 192.168.1.109
DHCP Mode: Server
> lan> dhcpserver dns 168.95.1.1 168.95.192.1
DNS setup:
First: 168.95.1.1
Second:168.95.192.1
> lan> setdhcp server
DHCP Mode: Server
range1:192.168.1.10 to 192.168.1.109
range2:0.0.0.0 to 0.0.0.0
default lease time:43200
max lease time:86400
DNS1:168.95.1.1
DNS2:168.95.192.1
> lan> home
>> save
2
Here is a complete step by step setup procedure for the Main Office LAN, SDTU01
Router. (HyperTerminal connection to serial port).
>> mode
Please select bridge or router:<b/r,r> r
Current mode is router
>> default
The data set to default successfully.
>> save
Saving configuration...Co nfiguration saved.
Updating flash filing system ...
System start...
>> quick
R1483(r)/ IPoA(i)/ PPPoA(p) / PPPoE(pe) : i
>> rtable
> rtable> deliproute all
> rtable> addiproute 192.168.1.0 255.255.255.0 10.1.1.2
> rtable> addiproute 0.0.0.0 0.0.0.0 192.168.0.254
> rtable> home
>> sdsl
> sdsl> terminal coe #set this unit to CO equipment
> sdsl> home
>> save
3
Saving configuration...Configuration saved.
Updating flash filing system ...
System start...
>>
>> rtable
> rtab le> show #confirm routing table has the WAN route
Routing Table: and Ethernet route
No. Destination IP SubMask Gateway IP
1 192.168.1.0 255.255.255.0 10.1.1.2
2 0.0.0.0 0.0.0.0 192.168.0.254
Lastly, you will need to add a routing entry in the Internet gateway's routing table to point
to your remote network. For example, all packets for 192.168.1.0 need to go to
192.168.0.253 (the SDTU).