Professional Documents
Culture Documents
REMOVAL
PROCEDURE
S E R V I C E M A N U A L
1.5/2.0/2.5/3.5 kW Class
Indoor Unit
Non-Inverter
Wall Mounted Type
Service Manual
Removal Procedure
Indoor Unit
zCooling Only
FT15LV14
FT20LV14
FT25LV14
FTE15LV1
FTE20LV1
FTE25LV1
FTE20MV1V
FTE25MV1V
FTNE15MV1
FTNE20MV1
FTNE25MV1
FTNE35MV1
FTNE15MV14
FTNE20MV14
FTNE25MV14
FTNE35MV14
FTNE25MV18
FTNE35MV18
Si041265EC
Table of Contents
1. Air Filters / Front Panel ...........................................................................2
2. Front Grille ..............................................................................................3
3. Horizontal Blades / Vertical Blade ASSYs ..............................................4
4. Electrical Box / PCBs / Swing Motor .......................................................5
5. Indoor Heat Exchanger ...........................................................................8
6. Fan Motor / Fan Rotor...........................................................................10
Note: The illustrations may be slightly different depending on the model.
Removal Procedure 1
Air Filters / Front Panel Si041265EC
(R18646)
Air filter
(R18647)
(R23426)
(R2513)
2 Removal Procedure
Si041265EC Front Grille
2. Front Grille
Warning Be sure to wait for 10 minutes or more after turning off all power supplies before
disassembling work.
Step Procedure Points
1 Remove the 2 screws.
(R18500)
Hook
Front
grille
(R2519)
(R2521)
Removal Procedure 3
Horizontal Blades / Vertical Blade ASSYs Si041265EC
(R2522)
Horizontal blade
(small) (R18761)
Right shaft
(R23377)
(R23378)
4 Removal Procedure
Si041265EC Electrical Box / PCBs / Swing Motor
(R18503)
3 Disconnect the Indoor heat [S1] / [CN_FAN] [S1] / [CN_FAN]: fan motor
connectors. exchanger thermistor [S7] / [CN_FANFB]: fan motor
[S6] / [CN_STP]: swing motor
4 Pull out the indoor heat
exchanger thermistor.
[S7] / [CN_FANFB]
[S6] / [CN_STP]
(R21155)
Terminal
board
(R18505)
(R21156)
Removal Procedure 5
Electrical Box / PCBs / Swing Motor Si041265EC
Push
here
Hook
(R21157)
(R18509)
Signal receiver
PCB
Hook (R18502)
6 Removal Procedure
Si041265EC Electrical Box / PCBs / Swing Motor
(R23376)
(R21158)
Swing motor
(R2543)
Removal Procedure 7
Indoor Heat Exchanger Si041265EC
Caution Be sure to conduct pump down operation before disassembling the refrigerant pipe.
If the refrigerant leaks, repair the spot of leaking, then collect all refrigerant from the
unit. After conducting vacuum drying, recharge proper amount of refrigerant.
From the viewpoint of global environmental protection, make sure to use a vacuum
pump for air purging.
Step Procedure Points
1 Remove the 2 screws Place a plastic sheet around
which fix the indoor the drain pan to prevent
heat exchanger to the wetting the floor with
installation plate. remaining drain.
(R18764)
(R2545)
Piping fixture
(R18760)
8 Removal Procedure
Si041265EC Indoor Heat Exchanger
(R2548)
(R21159)
(R2550)
Hook
(R18651)
Removal Procedure 9
Fan Motor / Fan Rotor Si041265EC
Right side
plate
(R18512)
(R9582)
(R2561)
10 Removal Procedure
Si041265EC Fan Motor / Fan Rotor
(R21160)
Hook
(R21161)
Left side
plate
(R2564)
Bearing
(R2565)
Removal Procedure 11
Revision History
Month / Year Version Revised contents
Dealer
Head Office:
Umeda Center Bldg., 2-4-12, Nakazaki-Nishi,
Kita-ku, Osaka, 530-8323 Japan
Tokyo Office:
JR Shinagawa East Bldg., 2-18-1, Konan,
Minato-ku, Tokyo, 108-0075 Japan
http://www.daikin.com/products/ac/
c All rights reserved
zSpecifications, designs and other content appearing in this brochure are current as of May 2016 but subject to change without notice.
Si041265EC
05/2016 AK.B