You are on page 1of 78

DOC. NO: REV.

0 Page No: 1 of 2

PROJECT: Date : 16-Jan-14

JOB NO : Designed By :

SUBJECT: Embedded Plate-BEP-03 Checked By : SB


EMBEDMENT SIZING AS PER PCI DESIGN HANDBOOK
Factored Shear Load Vu = 360 kN 80.93 Kip
Factored Tensile Load Nu1 = 0 kN 0.00 Kip case 1: Not near a free edge
Pc1 = 4 λ f 'c^0.5 [xy +2le(x+y)+4le²]
Nu2 = 0 kN 0.00 Kip
Pc2 = 4 λ f 'c^0.5 [2h(x+y +4le-4h)+4h²]
Eccentricity if any e1 = 0 mm 0.00 in
e2 = 0 mm 0.00 in
case 2: Near a free edge on one side
Pc1 = 4 λ f 'c^0.5 [xy +le(2x+y)+2le²
e3 = 60 mm 2.36 in
Pc2 = 4 λ f 'c^0.5 [h(2x+y +6le-6h)+2h²]
Stud Dia d = 19 mm 0.75 in
case 3: Near a free edge on 2 opposite
Embed plate thk tp = 16 mm 0.63 in sides
Corner stud to conc.edge dist de = 100 mm 3.94 in Pc1 = 4 λ f 'c^0.5 (xy +2lex)
Hor.Stud Spacing p = 100 mm 3.94 in Pc2 = 4 λ f 'c^0.5 2h(x+2le-2h)
Embedment length of stud le = 150 mm 5.91 in case 4: Near a free edge on 2
Hor.Distance bet edge to edge x = 300 mm 11.81 in adjacent sides
Pc1 = 4 λ f 'c^0.5 (xy +le(x+y)+le²)
Vert.spacing bet tension bolts y = 100 mm 3.94 in
Pc2 = 4 λ f 'c^0.5 [h(x+y+4le-4h)+h²]
Vert.Dist.as per sketch y1 = 850 mm 33.46 in
case 5: Near a free edge on 3 sides
Supporting Member thickness h = 250 mm 9.84 in
Pc1 = 4 λ f 'c^0.5 (xy +lex)
Depth of Fin Plate b = 820 mm 32.28 in
Pc2 = 4 λ f 'c^0.5 h(x+2le-2h)
Bott. edge dist fin pl to emb.pl b1 = 20.0 mm 0.79 in
λ = 1
No of studs in shear n1 = 14
No of studs in tension n2 = 2
Concrete Strength f'c = 30 N/mm² 4351 Psi
Strength of stud fy = 350 N/mm² 50763 Psi
Type of Concrete = Normal Weight
Case = case 2: Near a free edge on one side

Concrete Strength
Pull out strength of Concrete φPc = Min of Pc1 = 4 λ f 'c^0.5 [xy +le(2x+y)+2le²]
Pc2 = 4 λ f 'c^0.5 [h(2x+y +6le-6h)+2h²]
φPc = 61.3 Kip
C=T =0.85f'c ba a = 0.514 in
jud = 32.81399 in
Total Tension Pu = Vu e3 /jud +Nu1e1 / jud +Nu2e2 / jud + Nu1+Nu2
Pu = 5.8 Kip
φVc = Min of φ800Ab λ f'c'^0.5 or φ2πde² λ f'c'^0.5
φ800Ab λ f'c'^0.5 = 275.97 Kip
φ2πde² λ f'c'^0.5 = 76.45 Kip
φVc = 76.45 Kip

Combined capacity = 1/φ [ (Pu/Pc)² +(Vu/Vc)²] φ=0.85


= 0.960 < 1.00
DOC. NO: REV. 0 Page No: 2 of 2

PROJECT: Date : 16-Jan-14

JOB NO : Designed By :

SUBJECT: Embedded Plate-BEP-03 Checked By : SB

Steel Strength
Tensile Capacity of studs φPs = 0.9Abfy Ab=Area of stud
= 40.156 Kip
C=T =0.85f'c ba a = 0.34 in
jud = 32.90 in
Total Tension Pu = Vu e3 /jud +Nu1e1 / jud +Nu2e2 / jud + Nu1+Nu2
Pu = 5.8 Kip
Shear capacity of studs φVs = 0.75Abfy
= 234.2 Kip

Combined capacity = 1/φ [ (Pu/Ps)² +(Vu/Vs)²] φ=1.0


= 0.14 < 1.00

x = 300 mm
h = 250 mm

tp 16
de = 100 p = 100 mm mm Vu 360 kn
mm

d 19 Nu1 0
mm

e1 0 mm
y=
100 Nu2 0 Kn
mm y1 =
850 e2 0
mm

b 820
b1 20.0 mm

e3 60 mm
150 steel 0.14
mm concrete 0.96
2

Jan-14

4le²]
h)+4h²]
ne side
2le²
h)+2h²]
opposite

²)
+h²]
sides
2

Jan-14

kn

mm

mm
Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
Contract No 9-03 1 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR9 0 Approved By

Calculated Axial Load 62 kN STAAD for support no 6, T5..std


Calculated Shear Load 136 kN STAAD for support no 6, T5..std

Bolt Dia d 30 mm Material Grade Fy = 345 N/mm²


Bolt Pitch p 90 mm Fu = 448 N/mm²
Bolt Grade SA 325 N Weld Fuw = 480 N/mm²
No.of Bolts n 3 End projection t1 = 30 mm
Bolt Capacity fv 102.3 kN Fin Plate Thickness tf = 12 mm 0.42
Min.Hor.edge dist lh 60 mm Web plate thicknees tw = 12 mm 0.42
Min.Vert.Edge Dist lv 60 mm Weld size w = 10 mm 6
MAX.Eccentricity a 80 mm

lh
Design Axial Load with 0 % F.S Fa = 62 kN
Design Shear Load with 0 % F.S Fv = 136 kN
lv
Moment due to ecentricity M = 10880 kN-mm
Bolt Capacity
p
Bolt Shear Capacity = 102.3 kN
Bolt bearing capacity = min(d x tf ,d x tw )1.2 Fu
= 193.54 kN p
Bolt Capacity = 102 kN
tf
Fs
Elastic Section Modulus of Bolt Group Zbg= n(n+1)p/6 a
180 mm
Vertical force on bolt due to direct shear Fsv = Fv / n
45.33333 kN
Horizontal force on bolt due to axial tension Fsh = Fa/n FV
20.7 kN
Hori. force on outer most bolt due to moment Fsmh = M/Zbg
60.44444 kN
Resultant force on Remaining bolt due to shear+axial Fs = (Fsv²+Fsh²)^0.5
= 49.82 kN
Resultant force on outer most bolt due to shear+axial+moment
Fs = (Fsv²+(Fsh+Fsmh)²)^0.5
92.92 kN < 102 kN Ratio 0.908
Fin Plate Capacity

Net shear area Av = [((n-1)p + lv ) -( n - 0.5 )D]tf


1920.00 mm²
Net tension area At = (lh-0.5D)tf
= 528 mm²
Block shear capacity of the plate = 0.3AvFu +0.5At Fu
= 376.3 kN > 136 kN Ratio 0.361

Depth of Fin Plate provided df = 300 mm


Bending capacity of Fin Plate Mp = tf x df² x 0.6 xFy / 6
= 37260 kN-mm > 10880 kN-mm
Ratio 0.292

Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
EBS
Contract No 9-03 2 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR9 0 Approved By

Gross area in tension Agt = tf x df


= 3600 mm²
Net area in tension Ant = tf x df -nDtf
= 2448 mm²

Tension capacity of Fin Plate = Min( Agtx0.6Fy ,0.5FuxAnt)

= 548.352 kN > 62 kN Ratio 0.113

Weld Capcity
Length of the weld lw = 300 mm

Max.Shear per mm of weld due to direct shear f1 = Fv / 2lw


= 0.227 kN/mm
Max.Shear per mm of weld due to axial load f2 = Fa / 2lw
= 0.103 kN/mm
Section modulus of the weld S = 2l² /6
= 30000 mm³/mm
Max.Shear per mm of weld due to moment f3 = M/S
= 0.362667 kN/mm
Resultant load on weld fr = [f1²+(f2+f3)²]^0.5
= 0.518202 kN/mm
Provided Weld capacity Fw = 0.707xwx1x0.3Fuw
= 1.01808 kN/mm > 0.518202 kN/mm
Ratio 0.509

Note : As per assumption, line of action at the point where the fin plate is welded to the support,the provided weld is need to be
checked for both shear and axial load only.However , the weld is checked for moment inaddition to shear and axial load on co
16-Aug-05

J.Mahe

Davie

tf

16-Aug-05
J.Mahe

Davie

to be
co
Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
Contract No 9-03 1 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-8 -TR 6V 0 Approved By

Calculated Axial Load 31 kN STAAD for support no 7, T8..std


Calculated Shear Load 51 kN STAAD for support no 7, T8..std

Bolt Dia d 30 mm Material Grade Fy = 345 N/mm²


Bolt Pitch p 90 mm Fu = 448 N/mm²
Bolt Grade SA 325 N Weld Fuw = 480 N/mm²
No.of Bolts n 3 End projection t1 = 30 mm
Bolt Capacity fv 102.3 kN Fin Plate Thickness tf = 12 mm 0.42
Min.Hor.edge dist lh 60 mm Web plate thicknees tw = 12 mm 0.42
Min.Vert.Edge Dist lv 60 mm Weld size w = 10 mm 6
MAX.Eccentricity a 80 mm

lh
Design Axial Load with 10 % F.S Fa = 34.1 kN
Design Shear Load with 10 % F.S Fv = 56 kN
lv
Moment due to ecentricity M = 4488 kN-mm
Bolt Capacity
p
Bolt Shear Capacity = 102.3 kN
Bolt bearing capacity = min(d x tf ,d x tw )1.2 Fu
= 193.54 kN p
Bolt Capacity = 102 kN
tf
Fs
Elastic Section Modulus of Bolt Group Zbg= n(n+1)p/6 a
180 mm
Vertical force on bolt due to direct shear Fsv = Fv / n
18.7 kN
Horizontal force on bolt due to axial tension Fsh = Fa/n FV
11.4 kN
Hori. force on outer most bolt due to moment Fsmh = M/Zbg
24.93333 kN
Resultant force on Remaining bolt due to shear+axial Fs = (Fsv²+Fsh²)^0.5
= 21.88 kN
Resultant force on outer most bolt due to shear+axial+moment
Fs = (Fsv²+(Fsh+Fsmh)²)^0.5
40.83 kN < 102 kN Ratio 0.399
Fin Plate Capacity

Net shear area Av = [((n-1)p + lv ) -( n - 0.5 )D]tf


1920.00 mm²
Net tension area At = (lh-0.5D)tf
= 528 mm²
Block shear capacity of the plate = 0.3AvFu +0.5At Fu
= 376.3 kN > 56 kN Ratio 0.149

Depth of Fin Plate provided df = 300 mm


Bending capacity of Fin Plate Mp = tf x df² x 0.6 xFy / 6
= 37260 kN-mm > 4488 kN-mm
Ratio 0.12

Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
EBS
Contract No 9-03 2 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-8 -TR 6V 0 Approved By

Gross area in tension Agt = tf x df


= 3600 mm²
Net area in tension Ant = tf x df -nDtf
= 2448 mm²

Tension capacity of Fin Plate = Min( Agtx0.6Fy ,0.5FuxAnt)

= 548.352 kN > 34 kN Ratio 0.062

Weld Capcity
Length of the weld lw = 300 mm

Max.Shear per mm of weld due to direct shear f1 = Fv / 2lw


= 0.094 kN/mm
Max.Shear per mm of weld due to axial load f2 = Fa / 2lw
= 0.057 kN/mm
Section modulus of the weld S = 2l² /6
= 30000 mm³/mm
Max.Shear per mm of weld due to moment f3 = M/S
= 0.1496 kN/mm
Resultant load on weld fr = [f1²+(f2+f3)²]^0.5
= 0.226621 kN/mm
Provided Weld capacity Fw = 0.707xwx1x0.3Fuw
= 1.01808 kN/mm > 0.226621 kN/mm
Ratio 0.223

Note : As per assumption, line of action at the point where the fin plate is welded to the support,the provided weld is need to be
checked for both shear and axial load only.However , the weld is checked for moment inaddition to shear and axial load on
conservative side.
16-Aug-05

J.Mahe

Davie

tf

16-Aug-05
J.Mahe

Davie

to be
Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
Contract No 9-03 1 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-5 -TR 8 0 Approved By

Calculated Axial Load 171 kN STAAD for support no 26, T5.std


Calculated Shear Load 127 kN STAAD for support no 26, T5.std

Bolt Dia d 30 mm Material Grade Fy = 345 N/mm²


Bolt Pitch p 100 mm Fu = 448 N/mm²
Bolt Grade SA 325 N Weld Fuw = 480 N/mm²
No.of Bolts n 3 x 2 End projection t1 = 30 mm
Bolt Capacity fv 102.3 kN Fin Plate Thickness tf = 12 mm 0.42
Min.Hor.edge dist lh 60 mm Web plate thicknees tw = 12 mm 0.42
Min.Vert.Edge Dist lv 60 mm Weld size w = 10 mm 6
Max.Eccentricity a 80 mm
x 45 mm

lh
Design Axial Load with 0 % F.S Fa = 171 kN
Design Shear Load with 0 % F.S Fv = 127 kN
lv
Moment due to ecentricity M = 15875 kN-mm
Bolt Capacity
p
Bolt Shear Capacity = 102.3 kN
Bolt bearing capacity = min(d x tf ,d x tw )1.2 Fu
= 193.54 kN p
Bolt Capacity = 102 kN

tf
Inertia of bolt group Ibg = 52150 mm^4 x
Fs
Vertical force on bolt due to direct shear Fsv
= Fv / n
21.16667 kN a+x
Horizontal force on bolt due to axial tension Fsh = Fa/n
28.5 kN
Vert. force on outer most bolt due to moment Fsmv = M X / Ibg X = 45 mm
13.69847 kN
Hori. force on outer most bolt due to moment Fsmh = M Y / Ibg Y = 100 mm
30.44104 kN
Resultant force on outer most bolt due to shear+axial+moment
Fs = [(Fsv+Fsmv)²+(Fsh+Fsmh)²]^0.5
68.48 kN < 102 kN Ratio 0.669
Fin Plate Capacity

Net shear area Av = [((n-1)p + lv ) -( n - 0.5 )D]tf x2


4320.00 mm²
Net tension area At = (2x+lh-1.5D)tf
= 1224 mm²
Block shear capacity of the plate = 0.3AvFu +0.5At Fu
= 854.8 kN > 127 kN Ratio 0.149

Depth of Fin Plate provided df = 320 mm


Bending capacity of Fin Plate Mp = tf x df² x 0.6 xFy / 6
= 42394 kN-mm > 15875 kN-mm
Ratio 0.374

Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
EBS
Contract No 9-03 2 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-5 -TR 8 0 Approved By

Gross area in tension Agt = tf x df


= 3840 mm²
Net area in tension Ant = tf x df -nDtf
= 2688 mm²

Tension capacity of Fin Plate = Min( Agtx0.6Fy ,0.5FuxAnt)

= 602.112 kN > 171 kN Ratio 0.284

Weld Capacity

Length of the weld lw = 320 mm

Max.Shear per mm of weld due to direct shear f1 = Fv / 2lw


= 0.198 kN/mm
Max.Shear per mm of weld due to axial load f2 = Fa / 2lw
= 0.267 kN/mm
Section modulus of the weld S = 2l² /6
= 34133 mm³/mm
Max.Shear per mm of weld due to moment f3 = M/S
= 0.465088 kN/mm
Resultant load on weld fr = [f1²+(f2+f3)²]^0.5
= 0.758686 kN/mm
Provided Weld capacity Fw = 0.707xwx1x0.3Fuw
= 1.01808 kN/mm > 0.758686 kN/mm
Ratio 0.745

Note : As per assumption, line of action at the point where the fin plate is welded to the support,the provided weld is need to be
checked for both shear and axial load only.However , the weld is checked for moment inaddition to shear and axial load on co
16-Aug-05

J.Mahe

Davie

lv

tf

16-Aug-05
J.Mahe

Davie

to be
co
Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
Contract No 9-03 1 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 9 0 Approved By

Calculated Axial Load 62 kN STAAD for support no 36, T2.std


Calculated Shear Load 136 kN STAAD for support no 36, T2.std

Bolt Dia d 30 mm Material Grade Fy = 345 N/mm²


Bolt Pitch p 100 mm Fu = 448 N/mm²
Bolt Grade SA 325 N Weld Fuw = 480 N/mm²
No.of Bolts n 3 x 2 End projection t1 = 30 mm
Bolt Capacity fv 102.3 kN Fin Plate Thickness tf = 12 mm 0.42
Min.Hor.edge dist lh 60 mm Web plate thicknees tw = 12 mm 0.42
Min.Vert.Edge Dist lv 60 mm Weld size w = 10 mm 6
Max.Eccentricity a 80 mm
x 45 mm

lh
Design Axial Load with 0 % F.S Fa = 62 kN
Design Shear Load with 0 % F.S Fv = 136 kN
lv
Moment due to ecentricity M = 17000 kN-mm
Bolt Capacity
p
Bolt Shear Capacity = 102.3 kN
Bolt bearing capacity = min(d x tf ,d x tw )1.2 Fu
= 193.54 kN p
Bolt Capacity = 102 kN

tf
Inertia of bolt group Ibg = 52150 mm^4 x
Fs
Vertical force on bolt due to direct shear Fsv
= Fv / n
22.66667 kN a+x
Horizontal force on bolt due to axial tension Fsh = Fa/n
10.3 kN
Vert. force on outer most bolt due to moment Fsmv = M X / Ibg X = 45 mm
14.66922 kN
Hori. force on outer most bolt due to moment Fsmh = M Y / Ibg Y = 100 mm
32.59827 kN
Resultant force on outer most bolt due to shear+axial+moment
Fs = [(Fsv+Fsmv)²+(Fsh+Fsmh)²]^0.5
56.90 kN < 102 kN Ratio 0.556
Fin Plate Capacity

Net shear area Av = [((n-1)p + lv ) -( n - 0.5 )D]tf x2


4320.00 mm²
Net tension area At = (2x+lh-1.5D)tf
= 1224 mm²
Block shear capacity of the plate = 0.3AvFu +0.5At Fu
= 854.8 kN > 136 kN Ratio 0.159

Depth of Fin Plate provided df = 320 mm


Bending capacity of Fin Plate Mp = tf x df² x 0.6 xFy / 6
= 42394 kN-mm > 17000 kN-mm
Ratio 0.401

Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
EBS
Contract No 9-03 2 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 9 0 Approved By

Gross area in tension Agt = tf x df


= 3840 mm²
Net area in tension Ant = tf x df -nDtf
= 2688 mm²

Tension capacity of Fin Plate = Min( Agtx0.6Fy ,0.5FuxAnt)

= 602.112 kN > 62 kN Ratio 0.103

Weld Capacity

Length of the weld lw = 320 mm

Max.Shear per mm of weld due to direct shear f1 = Fv / 2lw


= 0.213 kN/mm
Max.Shear per mm of weld due to axial load f2 = Fa / 2lw
= 0.097 kN/mm
Section modulus of the weld S = 2l² /6
= 34133 mm³/mm
Max.Shear per mm of weld due to moment f3 = M/S
= 0.498047 kN/mm
Resultant load on weld fr = [f1²+(f2+f3)²]^0.5
= 0.631734 kN/mm
Provided Weld capacity Fw = 0.707xwx1x0.3Fuw
= 1.01808 kN/mm > 0.631734 kN/mm
Ratio 0.621

Note : As per assumption, line of action at the point where the fin plate is welded to the support,the provided weld is need to be
checked for both shear and axial load only.However , the weld is checked for moment inaddition to shear and axial load on co
16-Aug-05

J.Mahe

Davie

lv

tf

16-Aug-05
J.Mahe

Davie

to be
co
Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
Contract No 9-03 1 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-3 -TR 10L 0 Approved By

Calculated Axial Load 229 kN STAAD for support no 42, T3.std


Calculated Shear Load 114 kN STAAD for support no 42, T3.std

Bolt Dia d 30 mm Material Grade Fy = 345 N/mm²


Bolt Pitch p 100 mm Fu = 448 N/mm²
Bolt Grade SA 325 N Weld Fuw = 480 N/mm²
No.of Bolts n 3 x 2 End projection t1 = 30 mm
Bolt Capacity fv 102.3 kN Fin Plate Thickness tf = 12 mm 0.42
Min.Hor.edge dist lh 60 mm Web plate thicknees tw = 12 mm 0.42
Min.Vert.Edge Dist lv 60 mm Weld size w = 10 mm 6
Max.Eccentricity a 80 mm
x 45 mm

lh
Design Axial Load with 0 % F.S Fa = 229 kN
Design Shear Load with 0 % F.S Fv = 114 kN
lv
Moment due to ecentricity M = 14250 kN-mm
Bolt Capacity
p
Bolt Shear Capacity = 102.3 kN
Bolt bearing capacity = min(d x tf ,d x tw )1.2 Fu
= 193.54 kN p
Bolt Capacity = 102 kN

tf
Inertia of bolt group Ibg = 52150 mm^4 x
Fs
Vertical force on bolt due to direct shear Fsv = Fv / n
19 kN a+x
Horizontal force on bolt due to axial tension Fsh = Fa/n
38.2 kN
Vert. force on outer most bolt due to moment Fsmv = M X / Ibg X = 45 mm
12.29626 kN
Hori. force on outer most bolt due to moment Fsmh = M Y / Ibg Y = 100 mm
27.32502 kN
Resultant force on outer most bolt due to shear+axial+moment
Fs = [(Fsv+Fsmv)²+(Fsh+Fsmh)²]^0.5
72.59 kN < 102 kN Ratio 0.709
Fin Plate Capacity

Net shear area Av = [((n-1)p + lv ) -( n - 0.5 )D]tf x2


4320.00 mm²
Net tension area At = (2x+lh-1.5D)tf
= 1224 mm²
Block shear capacity of the plate = 0.3AvFu +0.5At Fu
= 854.8 kN > 114 kN Ratio 0.133

Depth of Fin Plate provided df = 320 mm


Bending capacity of Fin Plate Mp = tf x df² x 0.6 xFy / 6
= 42394 kN-mm > 14250 kN-mm
Ratio 0.336

Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
EBS
Contract No 9-03 2 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-3 -TR 10L 0 Approved By

Gross area in tension Agt = tf x df


= 3840 mm²
Net area in tension Ant = tf x df -nDtf
= 2688 mm²

Tension capacity of Fin Plate = Min( Agtx0.6Fy ,0.5FuxAnt)

= 602.112 kN > 229 kN Ratio 0.38

Weld Capacity

Length of the weld lw = 320 mm

Max.Shear per mm of weld due to direct shear f1 = Fv / 2lw


= 0.178 kN/mm
Max.Shear per mm of weld due to axial load f2 = Fa / 2lw
= 0.358 kN/mm
Section modulus of the weld S = 2l² /6
= 34133 mm³/mm
Max.Shear per mm of weld due to moment f3 = M/S
= 0.41748 kN/mm
Resultant load on weld fr = [f1²+(f2+f3)²]^0.5
= 0.795492 kN/mm
Provided Weld capacity Fw = 0.707xwx1x0.3Fuw
= 1.01808 kN/mm > 0.795492 kN/mm
Ratio 0.781

Note : As per assumption, line of action at the point where the fin plate is welded to the support,the provided weld is need to be
checked for both shear and axial load only.However , the weld is checked for moment inaddition to shear and axial load on co
16-Aug-05

J.Mahe

Davie

lv

tf

16-Aug-05
J.Mahe

Davie

to be
co
Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
Contract No 9-03 1 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 11 0 Approved By

Calculated Axial Load 220 kN STAAD for support no 65, T2.std


Calculated Shear Load 195 kN STAAD for support no 65, T2.std

Bolt Dia d 30 mm Material Grade Fy = 345 N/mm²


Bolt Pitch p 100 mm Fu = 448 N/mm²
Bolt Grade SA 325 N Weld Fuw = 480 N/mm²
No.of Bolts n 3 x 2 End projection t1 = 30 mm
Bolt Capacity fv 102.3 kN Fin Plate Thickness tf = 12 mm 0.42
Min.Hor.edge dist lh 60 mm Web plate thicknees tw = 12 mm 0.42
Min.Vert.Edge Dist lv 60 mm Weld size w = 10 mm 6
Max.Eccentricity a 80 mm
x 45 mm

lh
Design Axial Load with 0 % F.S Fa = 220 kN
Design Shear Load with 0 % F.S Fv = 195 kN
lv
Moment due to ecentricity M = 24375 kN-mm
Bolt Capacity
p
Bolt Shear Capacity = 102.3 kN
Bolt bearing capacity = min(d x tf ,d x tw )1.2 Fu
= 193.54 kN p
Bolt Capacity = 102 kN

tf
Inertia of bolt group Ibg = 52150 mm^4 x
Fs
Vertical force on bolt due to direct shear Fsv
= Fv / n
32.5 kN a+x
Horizontal force on bolt due to axial tension Fsh = Fa/n
36.7 kN
Vert. force on outer most bolt due to moment Fsmv = M X / Ibg X = 45 mm
21.03308 kN
Hori. force on outer most bolt due to moment Fsmh = M Y / Ibg Y = 100 mm
46.74017 kN
Resultant force on outer most bolt due to shear+axial+moment
Fs = [(Fsv+Fsmv)²+(Fsh+Fsmh)²]^0.5
99.11 kN < 102 kN Ratio 0.968
Fin Plate Capacity

Net shear area Av = [((n-1)p + lv ) -( n - 0.5 )D]tf x2


4320.00 mm²
Net tension area At = (2x+lh-1.5D)tf
= 1224 mm²
Block shear capacity of the plate = 0.3AvFu +0.5At Fu
= 854.8 kN > 195 kN Ratio 0.228

Depth of Fin Plate provided df = 320 mm


Bending capacity of Fin Plate Mp = tf x df² x 0.6 xFy / 6
= 42394 kN-mm > 24375 kN-mm
Ratio 0.575

Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
EBS
Contract No 9-03 2 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 11 0 Approved By

Gross area in tension Agt = tf x df


= 3840 mm²
Net area in tension Ant = tf x df -nDtf
= 2688 mm²

Tension capacity of Fin Plate = Min( Agtx0.6Fy ,0.5FuxAnt)

= 602.112 kN > 220 kN Ratio 0.365

Weld Capacity

Length of the weld lw = 320 mm

Max.Shear per mm of weld due to direct shear f1 = Fv / 2lw


= 0.305 kN/mm
Max.Shear per mm of weld due to axial load f2 = Fa / 2lw
= 0.344 kN/mm
Section modulus of the weld S = 2l² /6
= 34133 mm³/mm
Max.Shear per mm of weld due to moment f3 = M/S
= 0 kN/mm
Resultant load on weld fr = [f1²+(f2+f3)²]^0.5
= 0.459346 kN/mm
Provided Weld capacity Fw = 0.707xwx1x0.3Fuw
= 1.01808 kN/mm > 0.459346 kN/mm
Ratio 0.451
16-Aug-05

J.Mahe

Davie

lv

tf

16-Aug-05
J.Mahe

Davie
Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
Contract No 9-03 1 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-5 -TR8 0 Approved By

Calculated Axial Load 171 kN STAAD for support no 26, T5..std


Calculated Shear Load 127 kN STAAD for support no 26, T5..std

Bolt Dia d 30 mm Material Grade Fy = 345 N/mm²


Bolt Pitch p 90 mm Fu = 448 N/mm²
Bolt Grade SA 325 N Weld Fuw = 480 N/mm²
No.of Bolts n 4 End projection t1 = 30 mm
Bolt Capacity fv 102.3 kN Fin Plate Thickness tf = 12 mm 0.42
Min.Hor.edge dist lh 60 mm Web plate thicknees tw = 12 mm 0.42
Min.Vert.Edge Dist lv 60 mm Weld size w = 10 mm 6
MAX.Eccentricity a 80 mm

lh
Design Axial Load with 10 % F.S Fa = 188.1 kN
Design Shear Load with 10 % F.S Fv = 140 kN
lv
Moment due to ecentricity M = 11176 kN-mm
Bolt Capacity
p
Bolt Shear Capacity = 102.3 kN
Bolt bearing capacity = min(d x tf ,d x tw )1.2 Fu
= 193.54 kN p
Bolt Capacity = 102 kN
tf
Fs
Elastic Section Modulus of Bolt Group Zbg= n(n+1)p/6 a
300 mm
Vertical force on bolt due to direct shear Fsv = Fv / n
34.925 kN
Horizontal force on bolt due to axial tension Fsh = Fa/n
47.0 kN
Hori. force on outer most bolt due to moment Fsmh = M/Zbg
37.25333 kN
Resultant force on Remaining bolt due to shear+axial Fs = (Fsv²+Fsh²)^0.5
= 58.58 kN
Resultant force on outer most bolt due to shear+axial+moment
Fs = (Fsv²+(Fsh+Fsmh)²)^0.5
91.23 kN < 102 kN Ratio 0.891
Fin Plate Capacity

Net shear area Av = [((n-1)p + lv ) -( n - 0.5 )D]tf


2616.00 mm²
Net tension area At = (lh-0.5D)tf
= 528 mm²
Block shear capacity of the plate = 0.3AvFu +0.5At Fu
= 469.9 kN > 91 kN Ratio 0.194

Depth of Fin Plate provided df = 390 mm


Bending capacity of Fin Plate Mp = tf x df² x 0.6 xFy / 6
= 62969 kN-mm > 11176 kN-mm
Ratio 0.177

Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
EBS
Contract No 9-03 2 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-5 -TR8 0 Approved By

Weld Capcity
Length of the weld lw = 390 mm

Max.Shear per mm of weld due to direct shear f1 = Fv / 2lw


= 0.179 kN/mm
Max.Shear per mm of weld due to axial load f2 = Fa / 2lw
= 0.241 kN/mm
Section modulus of the weld S = 2l² /6
= 50700 mm³/mm
Max.Shear per mm of weld due to moment f3 = M/S
= 0.220434 kN/mm
Resultant load on weld fr = [f1²+(f2+f3)²]^0.5
= 0.495117 kN/mm
Provided Weld capacity Fw = 0.707xwx1x0.3Fuw
= 1.01808 kN/mm > 0.495117 kN/mm
Ratio 0.486
16-Aug-05

J.Mahe

Davie

tf

16-Aug-05
J.Mahe

Davie
Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
Contract No 9-03 1 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 09 0 Approved By

Calculated Axial Load 62 kN STAAD for support no 65, T2.std


Calculated Shear Load 136 kN STAAD for support no 65, T2.std

Bolt Dia d 30 mm Material Grade Fy = 345 N/mm²


Bolt Pitch p 90 mm Fu = 448 N/mm²
Bolt Grade SA 325 N Weld Fuw = 480 N/mm²
No.of Bolts n 4 End projection t1 = 30 mm
Bolt Capacity fv 102.3 kN Fin Plate Thickness tf = 12 mm 0.42
Min.Hor.edge dist lh 60 mm Web plate thicknees tw = 12 mm 0.42
Min.Vert.Edge Dist lv 60 mm Weld size w = 10 mm 6
MAX.Eccentricity a 80 mm

lh
Design Axial Load with 10 % F.S Fa = 68.2 kN
Design Shear Load with 10 % F.S Fv = 150 kN
lv
Moment due to ecentricity M = 11968 kN-mm
Bolt Capacity
p
Bolt Shear Capacity = 102.3 kN
Bolt bearing capacity = min(d x tf ,d x tw )1.2 Fu
= 193.54 kN p
Bolt Capacity = 102 kN
tf
Fs
Elastic Section Modulus of Bolt Group Zbg= n(n+1)p/6 a
300 mm
Vertical force on bolt due to direct shear Fsv = Fv / n
37.4 kN
Horizontal force on bolt due to axial tension Fsh = Fa/n
17.1 kN
Hori. force on outer most bolt due to moment Fsmh = M/Zbg
39.89333 kN
Resultant force on Remaining bolt due to shear+axial Fs = (Fsv²+Fsh²)^0.5
= 41.10 kN
Resultant force on outer most bolt due to shear+axial+moment
Fs = (Fsv²+(Fsh+Fsmh)²)^0.5
68.13 kN < 102 kN Ratio 0.666
Fin Plate Capacity

Net shear area Av = [((n-1)p + lv ) -( n - 0.5 )D]tf


2616.00 mm²
Net tension area At = (lh-0.5D)tf
= 528 mm²
Block shear capacity of the plate = 0.3AvFu +0.5At Fu
= 469.9 kN > 68 kN Ratio 0.145

Depth of Fin Plate provided df = 390 mm


Bending capacity of Fin Plate Mp = tf x df² x 0.6 xFy / 6
= 62969 kN-mm > 11968 kN-mm
Ratio 0.19

Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
EBS
Contract No 9-03 2 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 09 0 Approved By

Weld Capcity
Length of the weld lw = 390 mm

Max.Shear per mm of weld due to direct shear f1 = Fv / 2lw


= 0.192 kN/mm
Max.Shear per mm of weld due to axial load f2 = Fa / 2lw
= 0.087 kN/mm
Section modulus of the weld S = 2l² /6
= 50700 mm³/mm
Max.Shear per mm of weld due to moment f3 = M/S
= 0.236055 kN/mm
Resultant load on weld fr = [f1²+(f2+f3)²]^0.5
= 0.376074 kN/mm
Provided Weld capacity Fw = 0.707xwx1x0.3Fuw
= 1.01808 kN/mm > 0.376074 kN/mm
Ratio 0.369
16-Aug-05

J.Mahe

Davie

tf

16-Aug-05
J.Mahe

Davie
Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
Contract No 9-03 1 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 10 0 Approved By

Calculated Axial Load 17 kN STAAD for support no 17, T2.std


Calculated Shear Load 97 kN STAAD for support no 17, T2.std

Bolt Dia d 30 mm Material Grade Fy = 345 N/mm²


Bolt Pitch p 90 mm Fu = 448 N/mm²
Bolt Grade SA 325 N Weld Fuw = 480 N/mm²
No.of Bolts n 3 End projection t1 = 30 mm
Bolt Capacity fv 102.3 kN Fin Plate Thickness tf = 12 mm 0.42
Min.Hor.edge dist lh 60 mm Web plate thicknees tw = 12 mm 0.42
Min.Vert.Edge Dist lv 60 mm Weld size w = 10 mm 6
MAX.Eccentricity a 80 mm

lh
Design Axial Load with 10 % F.S Fa = 18.7 kN
Design Shear Load with 10 % F.S Fv = 107 kN
lv
Moment due to ecentricity M = 8536 kN-mm
Bolt Capacity
p
Bolt Shear Capacity = 102.3 kN
Bolt bearing capacity = min(d x tf ,d x tw )1.2 Fu
= 193.54 kN p
Bolt Capacity = 102 kN
tf
Fs
Elastic Section Modulus of Bolt Group Zbg= n(n+1)p/6 a
180 mm
Vertical force on bolt due to direct shear Fsv = Fv / n
35.56667 kN
Horizontal force on bolt due to axial tension Fsh = Fa/n
6.2 kN
Hori. force on outer most bolt due to moment Fsmh = M/Zbg
47.42222 kN
Resultant force on Remaining bolt due to shear+axial Fs = (Fsv²+Fsh²)^0.5
= 36.11 kN
Resultant force on outer most bolt due to shear+axial+moment
Fs = (Fsv²+(Fsh+Fsmh)²)^0.5
64.37 kN < 102 kN Ratio 0.629
Fin Plate Capacity

Net shear area Av = [((n-1)p + lv ) -( n - 0.5 )D]tf


1920.00 mm²
Net tension area At = (lh-0.5D)tf
= 528 mm²
Block shear capacity of the plate = 0.3AvFu +0.5At Fu
= 376.3 kN > 64 kN Ratio 0.171

Depth of Fin Plate provided df = 300 mm


Bending capacity of Fin Plate Mp = tf x df² x 0.6 xFy / 6
= 37260 kN-mm > 8536 kN-mm
Ratio 0.229

Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
EBS
Contract No 9-03 2 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 10 0 Approved By

Weld Capcity
Length of the weld lw = 300 mm

Max.Shear per mm of weld due to direct shear f1 = Fv / 2lw


= 0.178 kN/mm
Max.Shear per mm of weld due to axial load f2 = Fa / 2lw
= 0.031 kN/mm
Section modulus of the weld S = 2l² /6
= 30000 mm³/mm
Max.Shear per mm of weld due to moment f3 = M/S
= 0.284533 kN/mm
Resultant load on weld fr = [f1²+(f2+f3)²]^0.5
= 0.362341 kN/mm
Provided Weld capacity Fw = 0.707xwx1x0.3Fuw
= 1.01808 kN/mm > 0.362341 kN/mm
Ratio 0.356
16-Aug-05

J.Mahe

Davie

tf

16-Aug-05
J.Mahe

Davie
Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
Contract No 9-03 1 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 10 0 Approved By

Calculated Axial Load 48 kN STAAD for support no 70, T2.std


Calculated Shear Load 43 kN STAAD for support no 70, T2.std

Bolt Dia d 30 mm Material Grade Fy = 345 N/mm²


Bolt Pitch p 90 mm Fu = 448 N/mm²
Bolt Grade SA 325 N Weld Fuw = 480 N/mm²
No.of Bolts n 3 End projection t1 = 30 mm
Bolt Capacity fv 102.3 kN Fin Plate Thickness tf = 12 mm 0.42
Min.Hor.edge dist lh 60 mm Web plate thicknees tw = 12 mm 0.42
Min.Vert.Edge Dist lv 60 mm Weld size w = 10 mm 6
MAX.Eccentricity a 80 mm

lh
Design Axial Load with 10 % F.S Fa = 52.8 kN
Design Shear Load with 10 % F.S Fv = 47 kN
lv
Moment due to ecentricity M = 3784 kN-mm
Bolt Capacity
p
Bolt Shear Capacity = 102.3 kN
Bolt bearing capacity = min(d x tf ,d x tw )1.2 Fu
= 193.54 kN p
Bolt Capacity = 102 kN
tf
Fs
Elastic Section Modulus of Bolt Group Zbg= n(n+1)p/6 a
180 mm
Vertical force on bolt due to direct shear Fsv = Fv / n
15.76667 kN
Horizontal force on bolt due to axial tension Fsh = Fa/n
17.6 kN
Hori. force on outer most bolt due to moment Fsmh = M/Zbg
21.02222 kN
Resultant force on Remaining bolt due to shear+axial Fs = (Fsv²+Fsh²)^0.5
= 23.63 kN
Resultant force on outer most bolt due to shear+axial+moment
Fs = (Fsv²+(Fsh+Fsmh)²)^0.5
41.72 kN < 102 kN Ratio 0.408
Fin Plate Capacity

Net shear area Av = [((n-1)p + lv ) -( n - 0.5 )D]tf


1920.00 mm²
Net tension area At = (lh-0.5D)tf
= 528 mm²
Block shear capacity of the plate = 0.3AvFu +0.5At Fu
= 376.3 kN > 42 kN Ratio 0.111

Depth of Fin Plate provided df = 300 mm


Bending capacity of Fin Plate Mp = tf x df² x 0.6 xFy / 6
= 37260 kN-mm > 3784 kN-mm
Ratio 0.102

Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
EBS
Contract No 9-03 2 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 10 0 Approved By

Weld Capcity
Length of the weld lw = 300 mm

Max.Shear per mm of weld due to direct shear f1 = Fv / 2lw


= 0.079 kN/mm
Max.Shear per mm of weld due to axial load f2 = Fa / 2lw
= 0.088 kN/mm
Section modulus of the weld S = 2l² /6
= 30000 mm³/mm
Max.Shear per mm of weld due to moment f3 = M/S
= 0.126133 kN/mm
Resultant load on weld fr = [f1²+(f2+f3)²]^0.5
= 0.228184 kN/mm
Provided Weld capacity Fw = 0.707xwx1x0.3Fuw
= 1.01808 kN/mm > 0.228184 kN/mm
Ratio 0.224
16-Aug-05

J.Mahe

Davie

tf

16-Aug-05
J.Mahe

Davie
Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
Contract No 9-03 1 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-3 -TR 10L 0 Approved By

Calculated Axial Load 229 kN STAAD for support no 42, T3.std


Calculated Shear Load 114 kN STAAD for support no 42, T3.std

Bolt Dia d 30 mm Material Grade Fy = 345 N/mm²


Bolt Pitch p 90 mm Fu = 448 N/mm²
Bolt Grade SA 325 N Weld Fuw = 480 N/mm²
No.of Bolts n 4 End projection t1 = 30 mm
Bolt Capacity fv 102.3 kN Fin Plate Thickness tf = 12 mm 0.42
Min.Hor.edge dist lh 60 mm Web plate thicknees tw = 12 mm 0.42
Min.Vert.Edge Dist lv 60 mm Weld size w = 10 mm 6
MAX.Eccentricity a 80 mm

lh
Design Axial Load with 10 % F.S Fa = 251.9 kN
Design Shear Load with 10 % F.S Fv = 125 kN
lv
Moment due to ecentricity M = 10032 kN-mm
Bolt Capacity
p
Bolt Shear Capacity = 102.3 kN
Bolt bearing capacity = min(d x tf ,d x tw )1.2 Fu
= 193.54 kN p
Bolt Capacity = 102 kN
tf
Fs
Elastic Section Modulus of Bolt Group Zbg= n(n+1)p/6 a
300 mm
Vertical force on bolt due to direct shear Fsv = Fv / n
31.35 kN
Horizontal force on bolt due to axial tension Fsh = Fa/n
63.0 kN
Hori. force on outer most bolt due to moment Fsmh = M/Zbg
33.44 kN
Resultant force on Remaining bolt due to shear+axial Fs = (Fsv²+Fsh²)^0.5
= 70.35 kN
Resultant force on outer most bolt due to shear+axial+moment
Fs = (Fsv²+(Fsh+Fsmh)²)^0.5
101.38 kN < 102 kN Ratio 0.991
Fin Plate Capacity

Net shear area Av = [((n-1)p + lv ) -( n - 0.5 )D]tf


2616.00 mm²
Net tension area At = (lh-0.5D)tf
= 528 mm²
Block shear capacity of the plate = 0.3AvFu +0.5At Fu
= 469.9 kN > 101 kN Ratio 0.216

Depth of Fin Plate provided df = 390 mm


Bending capacity of Fin Plate Mp = tf x df² x 0.6 xFy / 6
= 62969 kN-mm > 10032 kN-mm
Ratio 0.159

Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
EBS
Contract No 9-03 2 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-3 -TR 10L 0 Approved By

Weld Capcity
Length of the weld lw = 390 mm

Max.Shear per mm of weld due to direct shear f1 = Fv / 2lw


= 0.161 kN/mm
Max.Shear per mm of weld due to axial load f2 = Fa / 2lw
= 0.323 kN/mm
Section modulus of the weld S = 2l² /6
= 50700 mm³/mm
Max.Shear per mm of weld due to moment f3 = M/S
= 0.19787 kN/mm
Resultant load on weld fr = [f1²+(f2+f3)²]^0.5
= 0.545068 kN/mm
Provided Weld capacity Fw = 0.707xwx1x0.3Fuw
= 1.01808 kN/mm > 0.545068 kN/mm
Ratio 0.535
16-Aug-05

J.Mahe

Davie

tf

16-Aug-05
J.Mahe

Davie
Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
Contract No 9-03 1 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 11 0 Approved By

Calculated Axial Load 220 kN STAAD for support no 65, T2.std


Calculated Shear Load 195 kN STAAD for support no 65, T2.std

Bolt Dia d 30 mm Material Grade Fy = 345 N/mm²


Bolt Pitch p 90 mm Fu = 448 N/mm²
Bolt Grade SA 325 N Weld Fuw = 480 N/mm²
No.of Bolts n 5 End projection t1 = 30 mm
Bolt Capacity fv 102.3 kN Fin Plate Thickness tf = 12 mm 0.42
Min.Hor.edge dist lh 60 mm Web plate thicknees tw = 12 mm 0.42
Min.Vert.Edge Dist lv 60 mm Weld size w = 10 mm 6
MAX.Eccentricity a 80 mm

lh
Design Axial Load with 10 % F.S Fa = 242 kN
Design Shear Load with 10 % F.S Fv = 215 kN
lv
Moment due to ecentricity M = 17160 kN-mm
Bolt Capacity
p
Bolt Shear Capacity = 102.3 kN
Bolt bearing capacity = min(d x tf ,d x tw )1.2 Fu
= 193.54 kN p
Bolt Capacity = 102 kN
tf
Fs
Elastic Section Modulus of Bolt Group Zbg= n(n+1)p/6 a
450 mm
Vertical force on bolt due to direct shear Fsv = Fv / n
42.9 kN
Horizontal force on bolt due to axial tension Fsh = Fa/n
48.4 kN
Hori. force on outer most bolt due to moment Fsmh = M/Zbg
38.13333 kN
Resultant force on Remaining bolt due to shear+axial Fs = (Fsv²+Fsh²)^0.5
= 64.68 kN
Resultant force on outer most bolt due to shear+axial+moment
Fs = (Fsv²+(Fsh+Fsmh)²)^0.5
96.58 kN < 102 kN Ratio 0.944
Fin Plate Capacity

Net shear area Av = [((n-1)p + lv ) -( n - 0.5 )D]tf


3312.00 mm²
Net tension area At = (lh-0.5D)tf
= 528 mm²
Block shear capacity of the plate = 0.3AvFu +0.5At Fu
= 563.4 kN > 97 kN Ratio 0.171

Depth of Fin Plate provided df = 480 mm


Bending capacity of Fin Plate Mp = tf x df² x 0.6 xFy / 6
= 95386 kN-mm > 17160 kN-mm
Ratio 0.18

Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
EBS
Contract No 9-03 2 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 11 0 Approved By

Weld Capcity
Length of the weld lw = 480 mm

Max.Shear per mm of weld due to direct shear f1 = Fv / 2lw


= 0.223 kN/mm
Max.Shear per mm of weld due to axial load f2 = Fa / 2lw
= 0.252 kN/mm
Section modulus of the weld S = 2l² /6
= 76800 mm³/mm
Max.Shear per mm of weld due to moment f3 = M/S
= 0.223438 kN/mm
Resultant load on weld fr = [f1²+(f2+f3)²]^0.5
= 0.525399 kN/mm
Provided Weld capacity Fw = 0.707xwx1x0.3Fuw
= 1.01808 kN/mm > 0.525399 kN/mm
Ratio 0.516
16-Aug-05

J.Mahe

Davie

tf

16-Aug-05
J.Mahe

Davie
Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
Contract No 9-03 1 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 11 0 Approved By

Calculated Axial Load 130 kN STAAD for support no 12, T2.std


Calculated Shear Load 91 kN STAAD for support no 12, T2.std

Bolt Dia d 30 mm Material Grade Fy = 345 N/mm²


Bolt Pitch p 90 mm Fu = 448 N/mm²
Bolt Grade SA 325 N Weld Fuw = 480 N/mm²
No.of Bolts n 4 End projection t1 = 30 mm
Bolt Capacity fv 102.3 kN Fin Plate Thickness tf = 12 mm 0.42
Min.Hor.edge dist lh 60 mm Web plate thicknees tw = 12 mm 0.42
Min.Vert.Edge Dist lv 60 mm Weld size w = 10 mm 6
MAX.Eccentricity a 80 mm

lh
Design Axial Load with 10 % F.S Fa = 143 kN
Design Shear Load with 10 % F.S Fv = 100 kN
lv
Moment due to ecentricity M = 8008 kN-mm
Bolt Capacity
p
Bolt Shear Capacity = 102.3 kN
Bolt bearing capacity = min(d x tf ,d x tw )1.2 Fu
= 193.54 kN p
Bolt Capacity = 102 kN
tf
Fs
Elastic Section Modulus of Bolt Group Zbg= n(n+1)p/6 a
300 mm
Vertical force on bolt due to direct shear Fsv = Fv / n
25.025 kN
Horizontal force on bolt due to axial tension Fsh = Fa/n
35.8 kN
Hori. force on outer most bolt due to moment Fsmh = M/Zbg
26.69333 kN
Resultant force on Remaining bolt due to shear+axial Fs = (Fsv²+Fsh²)^0.5
= 43.64 kN
Resultant force on outer most bolt due to shear+axial+moment
Fs = (Fsv²+(Fsh+Fsmh)²)^0.5
67.27 kN < 102 kN Ratio 0.657
Fin Plate Capacity

Net shear area Av = [((n-1)p + lv ) -( n - 0.5 )D]tf


2616.00 mm²
Net tension area At = (lh-0.5D)tf
= 528 mm²
Block shear capacity of the plate = 0.3AvFu +0.5At Fu
= 469.9 kN > 67 kN Ratio 0.143

Depth of Fin Plate provided df = 390 mm


Bending capacity of Fin Plate Mp = tf x df² x 0.6 xFy / 6
= 62969 kN-mm > 8008 kN-mm
Ratio 0.127

Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
EBS
Contract No 9-03 2 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 11 0 Approved By

Weld Capcity
Length of the weld lw = 390 mm

Max.Shear per mm of weld due to direct shear f1 = Fv / 2lw


= 0.128 kN/mm
Max.Shear per mm of weld due to axial load f2 = Fa / 2lw
= 0.183 kN/mm
Section modulus of the weld S = 2l² /6
= 50700 mm³/mm
Max.Shear per mm of weld due to moment f3 = M/S
= 0.157949 kN/mm
Resultant load on weld fr = [f1²+(f2+f3)²]^0.5
= 0.364613 kN/mm
Provided Weld capacity Fw = 0.707xwx1x0.3Fuw
= 1.01808 kN/mm > 0.364613 kN/mm
Ratio 0.358
16-Aug-05

J.Mahe

Davie

tf

16-Aug-05
J.Mahe

Davie
Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
Contract No 9-03 1 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 17V 0 Approved By

Calculated Axial Load 239 kN STAAD for support no 30, T2.std


Calculated Shear Load 5 kN STAAD for support no 30, T2.std

Bolt Dia d 30 mm Material Grade Fy = 345 N/mm²


Bolt Pitch p 90 mm Fu = 448 N/mm²
Bolt Grade SA 325 N Weld Fuw = 480 N/mm²
No.of Bolts n 4 End projection t1 = 30 mm
Bolt Capacity fv 102.3 kN Fin Plate Thickness tf = 12 mm 0.42
Min.Hor.edge dist lh 60 mm Web plate thicknees tw = 12 mm 0.42
Min.Vert.Edge Dist lv 60 mm Weld size w = 10 mm 6
MAX.Eccentricity a 80 mm

lh
Design Axial Load with 10 % F.S Fa = 262.9 kN
Design Shear Load with 10 % F.S Fv = 6 kN
lv
Moment due to ecentricity M = 440 kN-mm
Bolt Capacity
p
Bolt Shear Capacity = 102.3 kN
Bolt bearing capacity = min(d x tf ,d x tw )1.2 Fu
= 193.54 kN p
Bolt Capacity = 102 kN
tf
Fs
Elastic Section Modulus of Bolt Group Zbg= n(n+1)p/6 a
300 mm
Vertical force on bolt due to direct shear Fsv = Fv / n
1.375 kN
Horizontal force on bolt due to axial tension Fsh = Fa/n
65.7 kN
Hori. force on outer most bolt due to moment Fsmh = M/Zbg
1.466667 kN
Resultant force on Remaining bolt due to shear+axial Fs = (Fsv²+Fsh²)^0.5
= 65.74 kN
Resultant force on outer most bolt due to shear+axial+moment
Fs = (Fsv²+(Fsh+Fsmh)²)^0.5
67.21 kN < 102 kN Ratio 0.657
Fin Plate Capacity

Net shear area Av = [((n-1)p + lv ) -( n - 0.5 )D]tf


2616.00 mm²
Net tension area At = (lh-0.5D)tf
= 528 mm²
Block shear capacity of the plate = 0.3AvFu +0.5At Fu
= 469.9 kN > 67 kN Ratio 0.143

Depth of Fin Plate provided df = 390 mm


Bending capacity of Fin Plate Mp = tf x df² x 0.6 xFy / 6
= 62969 kN-mm > 440 kN-mm
Ratio 0.007

Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
EBS
Contract No 9-03 2 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 17V 0 Approved By

Weld Capcity
Length of the weld lw = 390 mm

Max.Shear per mm of weld due to direct shear f1 = Fv / 2lw


= 0.007 kN/mm
Max.Shear per mm of weld due to axial load f2 = Fa / 2lw
= 0.337 kN/mm
Section modulus of the weld S = 2l² /6
= 50700 mm³/mm
Max.Shear per mm of weld due to moment f3 = M/S
= 0.008679 kN/mm
Resultant load on weld fr = [f1²+(f2+f3)²]^0.5
= 0.345802 kN/mm
Provided Weld capacity Fw = 0.707xwx1x0.3Fuw
= 1.01808 kN/mm > 0.345802 kN/mm
Ratio 0.34
16-Aug-05

J.Mahe

Davie

tf

16-Aug-05
J.Mahe

Davie
Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
Contract No 9-03 1 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 17V 0 Approved By

Calculated Axial Load 200 kN STAAD for support no 66, T2.std


Calculated Shear Load 61 kN STAAD for support no 66, T2.std

Bolt Dia d 30 mm Material Grade Fy = 345 N/mm²


Bolt Pitch p 90 mm Fu = 448 N/mm²
Bolt Grade SA 325 N Weld Fuw = 480 N/mm²
No.of Bolts n 4 End projection t1 = 30 mm
Bolt Capacity fv 102.3 kN Fin Plate Thickness tf = 12 mm 0.42
Min.Hor.edge dist lh 60 mm Web plate thicknees tw = 12 mm 0.42
Min.Vert.Edge Dist lv 60 mm Weld size w = 10 mm 6
MAX.Eccentricity a 80 mm

lh
Design Axial Load with 10 % F.S Fa = 220 kN
Design Shear Load with 10 % F.S Fv = 67 kN
lv
Moment due to ecentricity M = 5368 kN-mm
Bolt Capacity
p
Bolt Shear Capacity = 102.3 kN
Bolt bearing capacity = min(d x tf ,d x tw )1.2 Fu
= 193.54 kN p
Bolt Capacity = 102 kN
tf
Fs
Elastic Section Modulus of Bolt Group Zbg= n(n+1)p/6 a
300 mm
Vertical force on bolt due to direct shear Fsv = Fv / n
16.775 kN
Horizontal force on bolt due to axial tension Fsh = Fa/n
55.0 kN
Hori. force on outer most bolt due to moment Fsmh = M/Zbg
17.89333 kN
Resultant force on Remaining bolt due to shear+axial Fs = (Fsv²+Fsh²)^0.5
= 57.50 kN
Resultant force on outer most bolt due to shear+axial+moment
Fs = (Fsv²+(Fsh+Fsmh)²)^0.5
74.80 kN < 102 kN Ratio 0.731
Fin Plate Capacity

Net shear area Av = [((n-1)p + lv ) -( n - 0.5 )D]tf


2616.00 mm²
Net tension area At = (lh-0.5D)tf
= 528 mm²
Block shear capacity of the plate = 0.3AvFu +0.5At Fu
= 469.9 kN > 75 kN Ratio 0.159

Depth of Fin Plate provided df = 390 mm


Bending capacity of Fin Plate Mp = tf x df² x 0.6 xFy / 6
= 62969 kN-mm > 5368 kN-mm
Ratio 0.085

Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
EBS
Contract No 9-03 2 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 17V 0 Approved By

Weld Capcity
Length of the weld lw = 390 mm

Max.Shear per mm of weld due to direct shear f1 = Fv / 2lw


= 0.086 kN/mm
Max.Shear per mm of weld due to axial load f2 = Fa / 2lw
= 0.282 kN/mm
Section modulus of the weld S = 2l² /6
= 50700 mm³/mm
Max.Shear per mm of weld due to moment f3 = M/S
= 0.105878 kN/mm
Resultant load on weld fr = [f1²+(f2+f3)²]^0.5
= 0.397353 kN/mm
Provided Weld capacity Fw = 0.707xwx1x0.3Fuw
= 1.01808 kN/mm > 0.397353 kN/mm
Ratio 0.39
16-Aug-05

J.Mahe

Davie

tf

16-Aug-05
J.Mahe

Davie
Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
Contract No 9-03 1 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 11 0 Approved By

Calculated Axial Load 220 kN STAAD for support no 65, T2.std


Calculated Shear Load 195 kN STAAD for support no 65, T2.std

Bolt Dia d 24 mm Material Grade Fy = 345 N/mm²


Bolt Pitch p 72 mm Fu = 450 N/mm²
Bolt Grade A325 N Weld Fuw = 480 N/mm²
Min.Hor.edge dist lh 48 mm Fin Plate Thickness tf = 10 mm
Min.Vert.Edge Dist lv 48 mm Web plate thicknees tw = 10 mm 0.42
Max.Eccentricity a 66 mm Weld size w = 10 mm 0.42
x 36 mm 5
Bolt Capacity fv 65.5 kN
No.of Bolts n 3 x 2

lh
Design Axial Load with 0 % F.S Fa = 220 kN
Design Shear Load with 0 % F.S Fv = 195 kN lv
Moment due to ecentricity M = 19890 kN-mm
Bolt Capacity p
Bolt Shear Capacity = 65.5 kN
Bolt bearing capacity = min(d x tf ,d x tw )1.2 Fu
= 129.60 kN p
Bolt Capacity = 66 kN

Inertia of bolt group Ibg = 28512 mm^4 x tf


Fs
Vertical force on bolt due to direct shear Fsv
= Fv / n
32.5 kN a+x
Horizontal force on bolt due to axial tension Fsh = Fa/n
36.7 kN
Vert. force on outer most bolt due to moment Fsmv = M X / Ibg X = 36 mm
25.11364 kN
Hori. force on outer most bolt due to moment Fsmh = M Y / Ibg Y = 72 mm
50.22727 kN
Resultant force on outer most bolt due to shear+axial+moment
Fs = [(Fsv+Fsmv)²+(Fsh+Fsmh)²]^0.5
104.26 kN > 66 kN Ratio 1.592
Fin Plate Capacity

Net shear area Av = [((n-1)p + lv ) -( n - 0.5 )D]tf x2


2540.00 mm²
Net tension area At = (2x+lh-1.5D)tf
= 810 mm²
Block shear capacity of the plate = 0.3AvFu +0.5At Fu
= 525.2 kN > 195 kN Ratio 0.371

Depth of Fin Plate provided df = 240 mm


Bending capacity of Fin Plate Mp = tf x df² x 0.6 xFy / 6
= 19872 kN-mm < 19890 kN-mm
Ratio 1

Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
EBS
Contract No 9-03 2 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 11 0 Approved By

Gross area in tension Agt = tf x df


= 2400 mm²
Net area in tension Ant = tf x df -nDtf
= 1620 mm²

Tension capacity of Fin Plate = Min( Agtx0.6Fy ,0.5FuxAnt)

= 364.5 kN > 220 kN Ratio 0.604

Weld Capacity

Length of the weld lw = 240 mm

Max.Shear per mm of weld due to direct shear f1 = Fv / 2lw


= 0.406 kN/mm
Max.Shear per mm of weld due to axial load f2 = Fa / 2lw
= 0.458 kN/mm
Section modulus of the weld S = 2l² /6
= 19200 mm³/mm
Max.Shear per mm of weld due to moment f3 = M/S
= 0 kN/mm
Resultant load on weld fr = [f1²+(f2+f3)²]^0.5
= 0.612461 kN/mm
Provided Weld capacity Fw = 0.707xwx1x0.3Fuw
= 1.01808 kN/mm > 0.612461 kN/mm
Ratio 0.602
16-Aug-05

J.Mahe

Davie

lv

tf

16-Aug-05
J.Mahe

Davie
Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
Contract No 9-03 1 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 11 0 Approved By

Calculated Axial Load 220 kN STAAD for support no 65, T2.std


Calculated Shear Load 195 kN STAAD for support no 65, T2.std

Bolt Dia d 24 mm Material Grade Fy = 345 N/mm²


Bolt Pitch p 72 mm Fu = 450 N/mm²
Bolt Grade A325 N Weld Fuw = 480 N/mm²
Min.Hor.edge dist lh 48 mm Fin Plate Thickness tf = 10 mm
Min.Vert.Edge Dist lv 48 mm Web plate thicknees tw = 10 mm 0.42
Max.Eccentricity a 66 mm Weld size w = 10 mm 0.42
x 36 mm 5
Bolt Capacity fv 65.5 kN
No.of Bolts n 4 x 2
lh

Design Axial Load with 0 % F.S Fa = 220 kN lv


Design Shear Load with 0 % F.S Fv = 195 kN
p
Moment due to ecentricity M = 19890 kN-mm
Bolt Capacity
Bolt Shear Capacity = 65.5 kN
Bolt bearing capacity = min(d x tf ,d x tw )1.2 Fu
= 129.60 kN p
Bolt Capacity = 66 kN

Inertia of bolt group Ibg = 62208 mm^4 tf


x
Fs
Vertical force on bolt due to direct shear Fsv
= Fv / n
24.375 kN a+x
Horizontal force on bolt due to axial tension Fsh = Fa/n
27.5 kN
Vert. force on outer most bolt due to moment Fsmv = M X / Ibg X = 36 mm
11.51042 kN
Hori. force on outer most bolt due to moment Fsmh = M Y / Ibg Y = 108 mm
34.53125 kN
Resultant force on outer most bolt due to shear+axial+moment
Fs = [(Fsv+Fsmv)²+(Fsh+Fsmh)²]^0.5
71.66 kN > 66 kN Ratio 1.094
Fin Plate Capacity

Net shear area Av = [((n-1)p + lv ) -( n - 0.5 )D]tf x2


3460.00 mm²
Net tension area At = (2x+lh-1.5D)tf
= 810 mm²
Block shear capacity of the plate = 0.3AvFu +0.5At Fu
= 649.4 kN > 195 kN Ratio 0.3

Depth of Fin Plate provided df = 312 mm


Bending capacity of Fin Plate Mp = tf x df² x 0.6 xFy / 6
= 33584 kN-mm > 19890 kN-mm
Ratio 0.592

Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
EBS
Contract No 9-03 2 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 11 0 Approved By

Gross area in tension Agt = tf x df


= 3120 mm²
Net area in tension Ant = tf x df -nDtf
= 2080 mm²

Tension capacity of Fin Plate = Min( Agtx0.6Fy ,0.5FuxAnt)

= 468 kN > 220 kN Ratio 0.47

Weld Capacity

Length of the weld lw = 312 mm

Max.Shear per mm of weld due to direct shear f1 = Fv / 2lw


= 0.313 kN/mm
Max.Shear per mm of weld due to axial load f2 = Fa / 2lw
= 0.353 kN/mm
Section modulus of the weld S = 2l² /6
= 32448 mm³/mm
Max.Shear per mm of weld due to moment f3 = M/S
= 0 kN/mm
Resultant load on weld fr = [f1²+(f2+f3)²]^0.5
= 0.471124 kN/mm
Provided Weld capacity Fw = 0.707xwx1x0.3Fuw
= 1.01808 kN/mm > 0.471124 kN/mm
Ratio 0.463
16-Aug-05

J.Mahe

Davie

lv

tf

16-Aug-05
J.Mahe

Davie
Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
Contract No 9-03 1 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 17V 0 Approved By

Calculated Axial Load 200 kN STAAD for support no 66, T2.std


Calculated Shear Load 61 kN STAAD for support no 66, T2.std

Bolt Dia d 30 mm Material Grade Fy = 345 N/mm²


Bolt Pitch p 100 mm Fu = 448 N/mm²
Bolt Grade SA 325 N Weld Fuw = 480 N/mm²
No.of Bolts n 3 x 2 End projection t1 = 30 mm
Bolt Capacity fv 102.3 kN Fin Plate Thickness tf = 12 mm 0.42
Min.Hor.edge dist lh 60 mm Web plate thicknees tw = 12 mm 0.42
Min.Vert.Edge Dist lv 60 mm Weld size w = 10 mm 6
Max.Eccentricity a 80 mm
x 45 mm

lh
Design Axial Load with 0 % F.S Fa = 200 kN
Design Shear Load with 0 % F.S Fv = 61 kN
lv
Moment due to ecentricity M = 7625 kN-mm
Bolt Capacity
p
Bolt Shear Capacity = 102.3 kN
Bolt bearing capacity = min(d x tf ,d x tw )1.2 Fu
= 193.54 kN p
Bolt Capacity = 102 kN

tf
Inertia of bolt group Ibg = 52150 mm^4 x
Fs
Vertical force on bolt due to direct shear Fsv
= Fv / n
10.16667 kN a+x
Horizontal force on bolt due to axial tension Fsh = Fa/n
33.3 kN
Vert. force on outer most bolt due to moment Fsmv = M X / Ibg X = 45 mm
6.579578 kN
Hori. force on outer most bolt due to moment Fsmh = M Y / Ibg Y = 100 mm
14.62128 kN
Resultant force on outer most bolt due to shear+axial+moment
Fs = [(Fsv+Fsmv)²+(Fsh+Fsmh)²]^0.5
50.79 kN < 102 kN Ratio 0.496
Fin Plate Capacity

Net shear area Av = [((n-1)p + lv ) -( n - 0.5 )D]tf x2


4320.00 mm²
Net tension area At = (2x+lh-1.5D)tf
= 1224 mm²
Block shear capacity of the plate = 0.3AvFu +0.5At Fu
= 854.8 kN > 61 kN Ratio 0.071

Depth of Fin Plate provided df = 320 mm


Bending capacity of Fin Plate Mp = tf x df² x 0.6 xFy / 6
= 42394 kN-mm > 7625 kN-mm
Ratio 0.18

Project KUWAIT TRADE CENTER Page Date 16-Aug-05

EBS
EBS
Contract No 9-03 2 of 2 Prepared By J.Mahe

CALCULATION SHEET FOR Rev Checked By Davie


EMIRATES BUILDING SYSTEMS
Fin Plate connection for Level T-2 -TR 17V 0 Approved By

Gross area in tension Agt = tf x df


= 3840 mm²
Net area in tension Ant = tf x df -nDtf
= 2688 mm²

Tension capacity of Fin Plate = Min( Agtx0.6Fy ,0.5FuxAnt)

= 602.112 kN > 200 kN Ratio 0.332

Weld Capacity

Length of the weld lw = 320 mm

Max.Shear per mm of weld due to direct shear f1 = Fv / 2lw


= 0.095 kN/mm
Max.Shear per mm of weld due to axial load f2 = Fa / 2lw
= 0.313 kN/mm
Section modulus of the weld S = 2l² /6
= 34133 mm³/mm
Max.Shear per mm of weld due to moment f3 = M/S
= 0.223389 kN/mm
Resultant load on weld fr = [f1²+(f2+f3)²]^0.5
= 0.544299 kN/mm
Provided Weld capacity Fw = 0.707xwx1x0.3Fuw
= 1.01808 kN/mm > 0.544299 kN/mm
Ratio 0.535

Note : As per assumption, line of action at the point where the fin plate is welded to the support,the provided weld is need to be
checked for both shear and axial load only.However , the weld is checked for moment inaddition to shear and axial load on co
16-Aug-05

J.Mahe

Davie

lv

tf

16-Aug-05
J.Mahe

Davie

to be
co

You might also like