You are on page 1of 2

ES-008PCQT

For Health Hazard and Continuous Pressure Applications


Job Name Contractor Approval

Job Location Engineer Approval

Contractors P.O. No. Representative

Series 008PCQT
Health Hazard, Anti-Siphon, Spill-Resistant Backflow Preventer
Sizes: 38", 12", 34" and 1" (10, 15, 20, 25mm)
Series 008PCQT is designed for indoor point-of-use applications to prevent backsiphonage of contaminated water back into the potable water supply. Separation of the water supply from the air inlet is accomplished by means of a diaphragm seal. This feature protects against any spillage during start-up or operation.

FOR INDOOR USE!

008PCQT-L (Left Handed)

008PCQT

Features
Standardly supplied with internal polymer coating Standardly supplied with Tee handles Available less Tee handle with stem wrench flats. For use where space is limited Available in left-handed or right-handed outlet Spill-resistant design for indoor use Affordable design Modular cartridge for ease of service Vent uses an O-ring for reliable operation Bronze body for durability Compact space saving design Satin chrome finish available Available with strainer
008PCQT (Right Handed)
HoodScrews (2Required) Vent Spring AirBleedScrew BleedO-ring (notshown)

Hood Bonnet O-ring Vent O-ring Body Retainer Check Assembly

TestCock

Shutoff ValveAssembly (2Required)

Installation
The 008PCQT is designed to be installed at the point of use. When factory installed deck/machine mounted on machines or equipment, the critical level of the 008PCQT shall be not less than 1" (25mm) above the flood rim. If field applied for general plumbing applications, the critical level of the 008PCQT shall be a minimum of 6" (150mm) above the flood rim.

Size: 38", 12" (10, 15mm)


HoodScrew Hood Bonnet O-ring Vent O-ring Body Retainer Check Assembly TestCock Shutoff ValveAssembly (2Required) Vent Spring

AirBleedScrew BleedO-ring (notshown)

Specifications
A spill-resistant vacuum breaker (SVB) shall be installed, in accordance with the manufacturer's instructions, as noted on the plans. The valve shall consist of a one-piece modular check and float assembly made of engineered thermoplastic and housed in a bronze body. Springs shall be stainless steel. The valve shall be constructed with a molded diaphragm separating the air inlet from the potable water supply to prevent spillage. The valve shall be a Watts Series 008PCQT.

Size: 34", 1" (20, 25mm)

Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements, please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold.

Materials
Springs: Bonnet: Vent Disc: Disc Holder: Check Disc: Body: Stainless steel PPO EPDM PPO Silicone rubber Bronze

Standards
Meets requirements of IAPMO.

Approvals

1056

B64.1.2

Listed by IAPMO, Approved by the Foundation for CrossConnection Control & Hydraulic Research at USC.
008PCQT-S WattsP60-M1 PressureReducingValve SolenoidValves

Pressure Temperature
Temperature Range: 33F 180F (0.5C 83C) Maximum Working Pressure: 150psi (10.3 bar)

End Connections
Female NPT - Ball Valve shutoffs

1"min. (25mm)

Testcock

Shutoff

Capacity
As compiled from documented Foundation for Cross-Connection Control and Hydraulic Research at the University of Southern California lab tests. *Typical maximum system flow rate (7.5 feet/sec.)
kPa psi 69 10 55 8 6 4 2 0 0 0 0.5 1.9 1 3.8 1.5 5.7 2 7.6 2.5 9.5 3 11.4 3.5 13.3 4 15.2 4.5 17.1 5 19 5.5 gpm 21 lpm
38

DispensingInducers "(20mm)Hose Adapterwith strainerwasher SupplyHose


34

Typical Installation

"(10mm)
kPa psi 69 10 55 8 6 4 2 0 0 0 5 19 10 38

34

"(20mm)

41 28 14 0

41 28 14 0

2",212",3"288A
15 57 7.5 2.3 20 76 25 95

FLOW
kPa psi 97 14 83 12 69 10 55 41 28 14 0 8 6 4 2 0 0 0 1 3.8 2 7.6 3 11.4 4 15.2 5 19 7.5 2.3 6 22.8 7 27 8 30 9 34 10 gpm 38 lpm fps mps
12

FLOW

30 gpm 114 lpm fps mps

"(15mm)

1"(25mm)
kPapsi 69 10 55 8 6 4 2 0 0 0 5 19 10 38 15 57 20 76 7.5 2.3 25 95 30 114 35 135 40 152 45 171 50 gpm 190 lpm fps mps

41 28 14 0

FLOW

FLOW

Dimensions Weights
2"

Note: A strainer is recommended to be installed ahead of the backflow preventer to prevent the fouling of the check assembly and resulting spillage from the valve during repressurization. Do not install in concealed locations or areas where water leakage due to normal wear of the internal parts can cause damage.

008PCQT
SIzE(DN) B in.
38

DIMENSIONS D mm in. mm in. E mm lbs. in.

WEIgHT kgs.

B D Bs

mm

10 12 15 34 20 1 25 008PCQT-S 38 10 12 15 34 20 1 25

512 534 7 712


Bs

140 146 178 191 200 216 260 284

31516 4316 458 518 31516 4316 458 518

100 106 117 130 100 106 117 130

318 338 412 478 318 338 412 478

79 86 114 124 79 86 114 124

1.6 1.7 3.8 4.8 3.4 3.5 5.6 7.6

.73 .77 1.72 2.18 1.54 1.59 2.54 3.45

7 812 1014 11316

78

A Watts Water Technologies Company

USA: No. Andover, MA Tel: (978) 688-1811 Fax: (978) 794-1848 www.watts.com Canada: Burlington, ON Tel: (905) 332-4090 Fax: (905) 332-7068 www.wattscanada.ca

ES-008PCQT

1118

2011 Watts

You might also like