Professional Documents
Culture Documents
A. Marking packets based onCoS value, IP precedence value, or DSCP value allows Layer 3
frames to be identified and distinguished from other packets.
B. Marking frames based only onCoS value or IP precedence value allows Layer 2 frames to be
identified and distinguished from other frames.
C. Marking packets or frames sets information in the Layer 2 and Layer 3 headers of a packet so
that the packet or frame can be identified and distinguished from other packets or frames.
D. Marking frames only sets information in the Layer 2 headers of a frame so that the frame can
be identified and distinguished from other packets or frames.
Answer: A
m
QUESTION NO: 2
.co
Voice packets are arriving at a destination with a variance of between 20 and 50 ms. If the jitter
buffer has a capacity of 30 ms, what is the impact on the audio at the receiving IP phone?
sts
A. The jitter buffer will replay the previous voice packets to replace those packets that exceed
30msto avoid speech gaps.
B. The audio stream at the receiving IP phone will be delayed and garbled.
lTe
C. The DSP will automatically increase the jitter buffer size after sampling the range of incoming
voice packets to accommodate the wider range in variation of voice packet arrival times to avoid
voice gaps.
tua
D. The IP phone will negotiate, in mid-call, a lower bandwidth codec to reduce the delay in the
arrival of voice packets to avoid voice gaps.
Ac
Answer: B
QUESTION NO: 3
Refer to the exhibit. Which type of ephone-dn is configured for the two ephones that are shown?
A. single-line-octo
Answer: E
QUESTION NO: 4
m
.co
Refer to the exhibit. Cisco Unified Communications Manager Express has been partially
configured to support 6 IP phones and 12 directory numbers. The Cisco Unified Communications
sts
Manager Express will use the IP address 10.1.130.1/24. Which two elements of the configuration
are missing from the command output and need to be added so that phones do not auto-register,
but can manually register with Cisco Unified Communications Manager Express? (Choose two.)
lTe
A. ip address 10.1.130.1
B. noreg-ephone
tua
C. create profile
D. ip source-address 10.1.130.1
E. createcnf-files
Ac
F. no auto-reg-ephone
Answer: D,F
QUESTION NO: 5
A. LLO adds a strict priority class to CBWFO. This class allows delay-sensitive data such as voice
to bedequeued and sent first.
B. LLO uses CBWFO to prioritize voice traffic anddequeue the voice packets so that they can be
handled first.
C. The strict priority queue has a higher weight than the queues in CBWFO. This weight allows the
delay-sensitive data such as voice to bedequeued and sent first.
"Pass Any Exam. Any Time." - www.actualtests.com 3
Cisco 642-437: Practice Exam
D. The LLO strict priority queue allows delay-sensitive data such as voice to bedequeued and sent
first (before packets in other queues are dequeued), giving delay-sensitive data preferential
treatment over other traffic.
Answer: D
QUESTION NO: 6
Your PSTN carrier sends digits to your TI PRI circuit in a digit-by-digit format. How must the T1
PRI circuit be configured to support this capability?
m
D. The serial interface that is associated with the T1/E1 controller needs to include the isdn
overlap-receiving command. .co
Answer: D
sts
QUESTION NO: 7
lTe
You have a Cisco Unified Border Element configured to provide H.323 to SIP interworking. Which
command will verify that you have a single H.323 and a single SIP call leg when the call is placed?
tua
Answer: A
QUESTION NO: 8
Which QoS technology provides a strict priority queuing scheme that allows delay-sensitive data
such as voice to be dequeued and sent before packets in other queues are dequeued, and also
works with WFQ and CBWFQ.
A. header compression
B. IP RTP Priority and Frame Relay IP RTP Priority
C. RSVP
Answer: D
QUESTION NO: 9
A. 16
B. 17
C. 18
D. 21
Answer: C
m
QUESTION NO: 10 DRAG DROP
.co
sts
lTe
tua
Ac
Answer:
Explanation:
m
.co
sts
lTe
tua
Answer:
m
QUESTION NO: 12
.co
A new Cisco 7965 IP phone is installed on a Cisco Unified Communications Manager Express
system. When the phone requests the .loads file from the TFTP server, it sees that the versions
are different. What does the IP phone do to resolve this issue?
sts
C. The IP phone boot requests the XMLDefault.cnf.xml file and boots up.
D. The IP phone does not boot up and will require manual intervention to factory reset the phone
before a new firmware image can be downloaded.
tua
Answer: B
Ac
QUESTION NO: 13
You are configuring a network to support voice to the PSTN. One important aspect to the
configuration is to be able to determine the individual slot, subunit, and port number from the
gateway endpoint identifier. Which signaling protocol is appropriate for this situation?
A. H.323
B. SIP
C. SCCP
D. MGCP
Answer: D
Answer:
m
.co
sts
lTe
tua
QUESTION NO: 15
How many IP phone calls can be sent across a 64-kb/s Frame Relay link that uses the G.729
Ac
codec? The sampling rate is 50 times a second, with 20 bytes per sample. There are 8 bytes of
Frame Relay header overhead with no checksum, and header compression is used.
A. 3
B. 4
C. 5
D. 7
Answer: C
QUESTION NO: 16
When Cisco Unified Border Element is configured to support RSVP-based CAC, at which point
during call setup are the RSVP path and reservation messages sent and received?
Answer: D
QUESTION NO: 17
Which command should be included in order to trust the DSCP-marked traffic from the distribution
m
layer?
Answer: C
lTe
QUESTION NO: 18
tua
Answer: E
Answer:
m
.co
sts
lTe
tua
Ac
QUESTION NO: 20
m
Refer to the exhibit. Your companyas QoS policy states that all traffic that is arriving at access
.co
layer switches from IP phones should be marked with a DSCP value of 46 and that all untagged
traffic that is arriving from a PC that is attached to an IP phone should be marked with a CoS value
of 1. Which two options will satisfy the requirements for the CoS-to-DSCP map and are the correct
sts
QoS commands? (Choose two.)
A. mis qos 1
lTe
Answer: B,C
Ac
QUESTION NO: 21
What is the reason that an outgoing call succeeds when there is no COR list that is applied to the
incoming dial peer and a COR list is applied to the outgoing dial peer?
A. The COR list for incoming calls on the incoming dial peer is a superset of COR lists for outgoing
calls on the outgoing dial peer.
B. COR lists for incoming calls on the incoming dial peer are not a superset of COR lists for
outgoing calls on the outgoing dial peer.
C. The outgoing dial peer, by default, has the lowest priority.
D. The incoming dial peer, by default, has the highest COR priority when no COR is applied.
QUESTION NO: 22
m
.co
sts
lTe
Refer to the exhibit. When an inbound PSTN call from 4087071222 arrives at the ISDN port that is
shown in the exhibit, which dial peer will be matched for the inbound leg?
tua
Answer: B
QUESTION NO: 23
Calls are failing to egress the local PSTN gateway that uses an E1 PRI circuit. Which debug
command would be most useful in determining which dialed digits are being sent to the PSTN?
Answer: C
QUESTION NO: 24
m
.co
sts
lTe
Refer to the exhibit. An administrator is migrating a PBX telephony system to an IP Phone solution
using a fixed numbering plan. The extension numbers and PSTN DIDs cannot be changed. Which
of the following methods can be used in order to reach the individual extensions at Site B when
tua
A. The administrator can add a 1 to the DID for Site B to become 300-555-31xxx.
Ac
B. The administrator needs to map the last four digits in the DID to the extension numbers and
prefix a site code.
C. The administrator needs to map the last four digits in the DID to the extension numbers and
prefix anintersite code.
D. The administrator needs to map the last four digits in the DID to the extension numbers using
translation rules.
E. No changes are necessary because PSTN calls are preceded with access code 9
Answer: D
Answer:
m
.co
sts
QUESTION NO: 26
lTe
The router with the IP address of 10.1.120.1 needs to be configured to use the device 10.1.140.1
as the clock source. Which configuration command wi accomplish this task?
tua
Answer: B
QUESTION NO: 27
Which two functions are associated with a voice gateway? (Choose two.)
A. switches voice channels between connected analog and digital voice circuits
B. provides voice-messaging services to connected analog and digital voice circuits
C. interconnects two logically separate VoIP networks
D. negotiates endpoint capabilities
Answer: A,E
QUESTION NO: 28
m
.co
sts
lTe
Refer to the exhibit. When an inbound PSTN call to 4087071222 is received by the router that is
shown in the exhibit, what is the resulting called number?
tua
A. 14087071222
B. 11222
C. 14081222
Ac
D. 1222
E. 4Q87071222
Answer: D
QUESTION NO: 29
A. Control is implemented by a series of plain-text commands that are sent over UDP port 2427
between Cisco Unified Communications Manager and the gateway.
B. A PRI backhaul channel forwards PRI Layer 2 (0.921) signaling information via a TCP
connection from the gateway to the call agent.
Answer: A,C,F
m
.co
sts
lTe
Answer:
tua
Ac
QUESTION NO: 31
Refer to the exhibit. Callers dial 0 to reach an outside line. When they try to place calls to directory
services (322) or services (422), they hear the reorder tone. What needs to be edited in the dial
peer to allow these calls to complete successfully?
m
F. The destination pattern needs to be edited so that the first digit that is matched is a 1 and the
forward-digits all command needs to be added to the dial peer.
.co
G. The destination pattern needs to be edited so that the first digit that is matched is a 0 and the
forward-digits 3 command needs to be added to the dial peer.
sts
Answer: G
lTe
QUESTION NO: 32
In which way does SIP Early Media differ from SIP Delayed Offer?
tua
A. In SIP Early Media mode, the SDP media capabilities are exchanged in the INVITE and the 200
OK messages.
Ac
Answer: B
QUESTION NO: 33
m
.co
sts
lTe
tua
Ac
Refer to the exhibit. Which class is always present even though it is not in the configuration snip?
A. class best-effort
B. class class-default
C. default class
D. best-effort class
E. class class-scavenger
Answer: B
QUESTION NO: 34
A. voice-port 0/0/0/
description fxs-did
signal did loop-start
i
voice-port 0/1/0
description fxo
signal loop-start
i
dial-peer voice 1 pots
incoming called-number.
direct-inward-dial
port 0/0/0
m
i
dial-peer voice 90 pots
destination-pattern 9T
port 0/1/0
.co
B. voice-port 0/0/0
sts
signal loop-start
i
voice-port 0/1/0
lTe
signal loop-start
i
dial-peer voice 1 pots
tua
incoming called-numberT
direct-inward-dial
!
Ac
Answer: B
QUESTION NO: 35
In which situation would an administrator configure telephony services, but not configure any
m
individual ephones?
.co
A. Phones that are controlled by Cisco Unified Communications Manager Express
B. Cisco Unified Communications ManagerSRSTfallback
C. Cisco Unified Communications Manager Express with HSRP
sts
D. Remotely located phones that are controlled by a third-party PBX
E. This is not a valid scenario.Ephones are always required.
lTe
Answer: B
tua
Answer:
QUESTION NO: 37
m
When configuring Cisco AutoQoS VoIP on a Cisco catalyst switch, how is the configuration
performed? .co
A. The autoqos voip command is applied to each interface.
sts
B. The autoqos voip command is applied globally in the switch.
C. Each interface will need either the autoqos voip cisco-phone or auto qos voip trust on each
interface, depending on the upstream device
lTe
D. Each interface will need either the autoqos voip trust cisco-phone or auto qos voip trust trust on
each interface, depending on the upstream device.
Answer: C
tua
Ac
QUESTION NO: 38
Which types of voice ports allow a small office to provide outbound DNIS and inbound DID?
Answer: E
Answer:
m
.co
sts
lTe
tua
Ac
QUESTION NO: 40
When a Cisco 7965 IP phone downloads an SCCP firmware file package, which file is downloaded
first by the IP phone from the TFTP server to describe the files it should request from the TFTP
server?
A. term45.default.loads
B. cnu45.8-4-0-79.sbn
C. term65.default.loads
D. dsp45.8-4-0-79.sbn
E. apps45.9-0-2ES2.sbn
F. SCCP45.9-0-2SR1S.loads
G. dsp45.8-4-0-79.sbn
H. jar45sccp.8-4-0-79.sbn
Answer: A
QUESTION NO: 41
m
E. SCCP uses hex messages for communication.
Answer: A,C
.co
sts
Answer:
m
QUESTION NO: 43
.co
sts
lTe
tua
Ac
Refer to the exhibit. What will the class map do if a packet arrives that is marked with a CoS of 6
and a DSCP value of EF?
A. The class map will match the packet and forward it to the policy map to be marked.
B. The class map will not map the packet and noOoS will be applied.
C. The class map will wait for the next packet in the stream to see if it has aCoS marking of 5 and
then forward both packets to the policy map
D. For the packet to be forwarded to the policy map, it must have aCoS of 5 and a DSCP value of
EF.
QUESTION NO: 44
How many VoIP G.729 calls can be made simultaneously over a 128-kb/s Frame Relay circuit
(Layer 3) if 50 percent of the circuit is dedicated to voice and 50 percent is dedicated to data?
A. 1
B. 2
C. 3
D. 4
E. 5
Answer: B
m
QUESTION NO: 45 .co
In a voice gateway, the configured codec complexity of the DSPs on a voice card can be changed.
What is the impact on the DSPs if high codec complexity is configured?
sts
A. The codec complexity affects call density, which is the number of calls that are reconciled on
the DSPs. This results in lower call density when high complexity is configured.
lTe
D. The DSP will process codecs that support high complexity transparently and shift to flex mode
for those codecs that are not high complexity
Ac
Answer: A
QUESTION NO: 46
Refer to the exhibit. A new Cisco Unified Communications Manager Express system has been
deployed and the technician is trying to add the first new IP phone to the system. The phone
powers up, but it does not register with the system. The technician has verified that the phone is
getting the proper VLAN information from Cisco Discovery Protocol. The phone is also getting the
correct IP address and TFTP server address from DHCP. The phone has been assigned to an
Answer: D,F
QUESTION NO: 47
m
A. Cisco Packet Loss Concealment technology decreases the voice sampling rate to 10 ms of the
voice payload to smooth gaps in the voice stream.
.co
B. Packet Loss Concealment intelligently analyzes missing packets and generates a reasonable
replacement packet to improve the voice quality
sts
C. Packet Loss Concealment will buffer 20 to 50 ms of a voice stream to minimize lost or out-of-
order voice packets.
lTe
D. Packet Loss Concealment will compensate for packet loss rates between 1 and 5 percent by
generating a reasonable replacement packet to improve the voice quality.
Answer: B
tua
QUESTION NO: 48
Ac
Which three methodologies are specific types of QoS used on a 512-kb/s point-to-point IP WAN
link? (Choose three.)
A. header compression
B. FRF.12
C. LLQ
D. MultilinkPPP
E. RSVP
Answer: A
m
Answer:
.co
sts
lTe
tua
Ac
QUESTION NO: 50
Which three of the following methods are used by a Cisco Unified Border Element to provide
network hiding? (Choose three.)
m
Answer:
.co
sts
lTe
tua
Ac
Explanation:
DSP delay, Packetization delay, Serialization delay & Dejitter Buffer delay are Fixed delay types.
Queuing and Buffering delay & Network delay are Variable Delay types.
QUESTION NO: 52
m
.co
Refer to the exhibit. Consider an outgoing call that is being placed in all three scenarios that are
shown in the exhibit. What is the result of the call, going down the table from top to bottom?
sts
A. success,success,success
B. success, success, fail
lTe
Answer: A
Ac
QUESTION NO: 53
Which three Cisco IOS commands are required to configure a voice gateway as a DHCP server to
support a data subnet with the IP address of 10.1.30.0/24 and a default gateway of 10.1.30.1/24?
(Choose three.)
A. ip dhcp pool
B. subnet 10.1.30.1 255.255.255.0
C. ip dhcp pool data
D. network 10.1.30.1/24
E. network 10.1.30.0 255.255.255.0
F. default-gw 10.1.30.1J24
Answer: C,E,G
QUESTION NO: 54
m
.co
sts
Refer to the exhibit. When an international call to 90114989531212001 is placed from extension
lTe
C. The call will fail because the incoming COR list is not a superset of the outgoing COR list.
D. The call will succeed because the incoming COR list has the highest priority, by default, when
no incoming COR list is applied.
Ac
Answer: D
QUESTION NO: 55
In which situation would the trust boundary be located at the access layer?
A. if the endpoints, both IP phones and PCs, are incapable of marking traffic properly
B. if PCs are switched through an IP phone and the IP phone traffic can be trusted to mark both
traffic streams properly
C. if the access layer switch cannot trust or re-mark incoming traffic from endpoints properly
D. if there are endpoints that cannot be trusted and connect directly to the distribution layer
QUESTION NO: 56
An access layer switch is configured to extend priority to an IP phone. Cisco Discovery Protocol is
enabled on all ports. What are the three possible ways that an IP phone can be instructed to treat
the Layer 2 CoS priority value of the attached PC? (Choose three.)
m
Answer: A,C,D
.co
QUESTION NO: 57
sts
lTe
Refer to the exhibit. When 5551234 is being matched with the outgoing dial peer that is shown in
tua
the exhibit, which of the following called numbers will be sent to the PSTN?
A. 5551234
Ac
B. 1234
C. 555
D. Null
E. 5
F. 51234
Answer: F
Answer:
m
.co
sts
lTe
tua
Ac
m
.co
sts
lTe
tua
Ac