Professional Documents
Culture Documents
DISH Pro (DP) Products DISH Pro Plus (DP Plus) Products
DP Single LNBF DP Plus Twin LNBF
DP Dual LNBF DP Plus 44 Switch
DP Twin LNBF DP Plus Separator
DP Quad LNBF
DP21 Switch
DP34 Switch
DP Adapter for Legacy
receivers
TWO ORBITAL LOCATIONS
Two Orbital Locations, 2 Tuners Two Orbital Locations, 4 Tuners
(1) DP Twin on a DISH 500 (1) DP Quad on a DISH 500
DISH 500
DISH 500
DP SINGLE TUNER
DP SINGLE TUNER
DP SINGLE TUNER
Or Legacy Receiver
DISH 500
LEGACY TUNER
DP SINGLE TUNER
Grounding according to the National Electric Code (NEC) and all local electrical codes is required.
2
THREE ORBITAL LOCATIONS
Three Orbital Locations, up to 4 Tuners Three Orbital Locations, up to 12 Tuners
DISH 500 DISH 500
DISH 500
(1) DP Twin on a DISH 500
(or two DP Dual LNBFs)
DISH 500 (1) DP Dual on a DISH 500
with I-Bracket
Up to (3) DP34 Switches
DP SINGLE TUNER
Or Legacy Receiver
To Receiver Tuner Inputs DP SINGLE TUNER with an adapter
Three Orbital Locations with a Legacy Receiver Three Orbital Locations, with DP Plus Twin
(1) DP Twin on a DISH 500 DISH 500 (1) DP Plus Twin on a DISH 500
(1) DP Dual on a DISH 500 with I-Bracket (1) DP Dual on a DISH 500
DISH (1) DP34 Switch with I-Bracket
500 (1) DP Adapter for each Legacy Receiver DISH 500 (1) DP Plus Separator
LEGACY TUNER
DP PLUS DUAL TUNER
Grounding according to the National Electric Code (NEC) and all local electrical codes is required.
3
FOUR ORBITAL LOCATIONS
DP Plus 44 Switch Connectivity
110° or 119°
61.5° or 148°
Each DP Plus 44 Switch requires a Power Inserter on port 1 To Receiver Tuner Inputs
To Receiver
Tuner Inputs
Each DP Plus 44 Switch requires a Power Inserter on port 1 To Receiver Tuner Inputs
Grounding according to the National Electric Code (NEC) and all local electrical codes is required.
4
DISH Pro & DISH Pro Plus Installation Considerations
LNBFs AND SWITCHES
DISH Pro LNBFs work with DISH Pro Plus switches. The DISH Pro Plus Twin functions the same as
a DISH Pro Twin LNBF when connected to any DISH Pro/DISH Pro Plus switch.
“Legacy” LNBFs and switches can never be used with DISH Pro or DISH Pro Plus LNBFs and
switches.
The maximum recommended cable length is 200 feet from the LNBFs to the furthest DISH Pro or
DISH Pro Plus receiver (150 feet for Legacy receivers).
When mounting switches, position according to instructions on the label.
Use drip loops to direct water away from F-connectors.
INSTALLATION MATERIALS
Materials used in a DISH Pro or DISH Pro Plus installation must be rated to 2150 MHz and pass DiSEqC
22 KHz tone.
These materials include:
RG-6 cable Line amps
Ground blocks Barrel connectors
Diplexers Wall plates
Splitters Surge protectors
DISH Network Retailers, please refer to the latest “DISH Pro Approved Accessories List” located on
http://retailer.echostar.com
6
LNBF & Switch Connectivity Chart
DISH Pro LNBFs DISH Pro Switches DISH Pro Plus LNBF DISH Pro Plus Switches
DP Single, DP Dual, DP21
DP Plus Twin DP Plus 44
DP Twin, DP Quad DP34
Legacy LNBFs or
No No No No
Switches
Yes – DP Single or DP Dual
DISH Pro LNBFs --- Yes Yes
using DP Plus Twin’s input port
DP21-No
Yes – LNBF’s input port and DP
DISH Pro Switches Yes --- DP34-Yes, but DP34(s) will not have DP
Plus capabilities disabled th
Plus capabilities or 4 orbital location
Yes – DP Single or DP Yes – LNBF’s input port will be disabled.
Yes – LNBF’s input port and DP Plus
DISH Pro Plus Twin Dual using DP Plus Twin’s --- DP Plus capabilities will occur within the
capabilities disabled
input port DP Plus switch
Yes – LNBF’s input port will be
DISH Pro Plus 44 disabled. DP Plus capabilities
Yes --- Yes
Switch will occur with`in the DP Plus
switch