Professional Documents
Culture Documents
Link
SPECIFICATIONS DISASSEMBLY SCHEMATIC DIAGRAMS
2008E0500-1
DSC-W80/W85_L2 © 2008.5
9-852-194-31 Sony EMCS Co. Published by Kohda TEC
SPECIFICATIONS
DSC-W80/W85_L2
—2—
Model information table
Model DSC-W80/Silver DSC-W80/Black DSC-W80/White DSC-W80/Pink DSC-W85/Silver
US, CND, AEP, UK, US, CND, AEP, US, CND, AEP, US, CND, AEP,
Destination CND, AEP, UK, E,
E, AUS, HK, CH, UK, E, AUS, HK, UK, E, AUS, HK, UK, E, AUS, HK,
AUS, KR
KR, AR, BR, J, JE CH, KR, JE CH, KR, J, JE CH, KR, J, JE
• Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
EE : East European model
HK : Hong Kong model
J : Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
SAFETY CHECK-OUT
1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder
connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead-
and bridges. free mark (LF) indicating the solder contains no lead.
2. Check the interboard wiring to ensure that no wires are (Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point : LEAD FREE MARK
them out to the customer and recommend their replacement. Unleaded solder has the following characteristics.
4. Look for parts which, through functioning, show obvious signs • Unleaded solder melts at a temperature about 40°C higher than
of deterioration. Point them out to the customer and ordinary solder.
recommend their replacement. Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
5. Check the B+ voltage to see it is at the values specified.
Soldering irons using a temperature regulator should be set to
6. FLEXIBLE Circuit Board Repairing about 350°C.
• Keep the temperature of the soldering iron around 270°C Caution: The printed pattern (copper foil) may peel away if the
during repairing. heated tip is applied for too long, so be careful!
• Do not touch the soldering iron on the same conductor of the • Strong viscosity
circuit board (within 3 times). Unleaded solder is more viscous (sticky, less prone to flow) than
• Be careful not to apply force on the conductor when soldering ordinary solder so use caution not to let solder bridges occur such
or unsoldering. as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
DSC-W80/W85_L2
—3—
TABLE OF CONTENTS
Section Title Page
1. SERVICE NOTE
1-1. Precaution on Replacing the SY-173 Board ···················· 1-1
1-2. Self-diagnosis Function ··················································· 1-1
1-3. Process After Fixing Flash Error ····································· 1-2
1-4. Method for Copying or Erasing the Data in Internal
Memory ··········································································· 1-3
1-5. How to Write Data to Internal Memory ·························· 1-4
2. DISASSEMBLY
2-1. Identifying Parts ······························································ 2-2
2-2. Disassembly ····································································· 2-3
2-3. Exchange method of barrier block ·································· 2-6
2-4. Exchange method of zoom gear block ···························· 2-8
3. BLOCK DIAGRAMS
3-1. Overall Block Diagram (1/2) ··········································· 3-1
3-2. Overall Block Diagram (2/2) ··········································· 3-2
3-3. Power Block Diagram (1/2) ············································· 3-3
3-4. Power Block Diagram (2/2) ············································· 3-4
DSC-W80/W85_L2
—4—
1. SERVICE NOTE ENGLISH JAPANESE
LCD screen
Blinks at 3.2 Hz
C 32 00
DSC-W80/W85_L2
1-1
ENGLISH JAPANESE
Initializes the setting to the default setting. Even if you execute this function, the images
stored in the internal memory are retained.
1 Select [Initialize] with v/V/b/B, then press z.
The message “Initialize all settings” appears.
2 Select [OK] with v, then press z.
The settings are reset to the default setting.
DSC-W80/W85_L2
1-2
ENGLISH JAPANESE
Note 1: When replacing the SY-173 board, erase the data in internal memory of the board before replacement.
Note 2: When replacing the SY-173 board, execute formatting and initialize the internal memory after replacement.
• Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little
remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.
• You cannot copy individual images.
• The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the “Memory Stick Duo” after copying, then execute the [Format] command in
[Internal Memory Tool].
• When you copy the data in the internal memory to the “Memory Stick Duo”, all the data will be copied.
You cannot choose a specific folder on the “Memory Stick Duo” as the destination for the data to be
copied.
.
• Even if you copy data, a (Print order) mark is not copied
Format
DSC-W80/W85_L2
1-3
ENGLISH JAPANESE
4) Upon completion of the setting change, the following message will be displayed.
5) Return the driver to the original one, and connect the PC to the camera (USB mode: Mass Storage).
6) Write the data read out into the PC to the internal memory of the camera.
7) Disconnect the PC from the camera, and turn off the camera.
Note: By turning off the camera, the write enable setting is reset.
DSC-W80/W85_L2
1-4
1. SERVICE NOTE ENGLISH JAPANESE
1-1. SY-173基板交換時の注意
仕向けデータ
補修用基板と交換する時,補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。
ADJ編を参照して,「DESTINATION DATA WRITE」を行ってください。
USBシリアルNo.
セットは,1台毎に異なる固有のID(USB Serial No.)を書き込んだ後,出荷されています。
新品の補修用基板には,このIDが書き込まれていないので,基板交換後にIDを入力する必要があります。
ADJ編を参照して,「USB SERIAL No. INPUT」を行ってください。
1-2. 自己診断機能
1-2-1. 自己診断機能について 1-2-2. 自己診断表示
本機の動作に不具合が生じたとき,自己診断機能が働き, 本機の動作に不具合が生じたとき,LCD画面にアルファベッ
L C D 画面に,どう処置したらよいか判断できる表示を行い トと4桁の数字が表示され,3.2Hzで点滅します。この5文字
ます。自己診断機能については取扱説明書にも掲載されて の表示によって対応者分類および不具合の生じたブロックの
います。 分類,不具合の詳細コードを示します。
LCD画面
C : 3 2 : 00
3.2Hz点滅
C 32 00
DSC-W80/W85_L2
1-5
Ver. 1.1 2008.05
ENGLISH JAPANESE
1-2-3. 自己診断コード表
自己診断コード
内蔵メモリにフォーマットエラーが 内蔵メモリをフォーマットする。
あった。
フォーマットしていない“メモリー “メモリースティック デュオ”をフォーマットする。
スティック デュオ”を入れた。
C 1 3 0 1 “メモリースティック デュオ”が 新しい“メモリースティック デュオ”に交換する。
壊れている。
“メモリースティック デュオ”の 規格内の“メモリースティック デュオ”を挿入する。
タイプエラーを検出した。
“メモリースティック デュオ”が 電源の入れ直し,または“メモリースティック デュオ”
読み/書きできない。 の挿し/外しを数回試す。
C 3 2 0 1 ハードウェアトラブルを検出した。 電源を入れ直す。
E 6 1 0 0 フォーカスが合いにくい。 操作スイッチの電源を入れ直す。
(フォーカスの初期化ができない) 復帰しない場合はレンズブロックのフォーカスリセットセ
ンサ(SY-173基板CN402 wsピン)を点検する。異常なけ
ればフォーカスモータ駆動IC(SY-173基板IC401)を点検
する。
E 6 1 1 0 ズーム動作の異常。 操作スイッチの電源を入れ直す。
(ズームレンズの初期化ができな ズームボタンを操作したときにズーム動作をすればレンズ
い) ブロックのズームリセットセンサ(SY-173基板CN402 ra
ピン)を点検する。異常なければズームモータ駆動IC
(SY-173基板IC401)を点検する。
E 6 2 0 2 手振れ補正用ICの異常。 手振れ補正用IC(SY-173基板IC503)を点検または交換す
る。
E 6 2 1 0 手振れ補正用ICの異常。 手振れ補正用IC(SY-173基板IC503)を点検または交換す
(レンズ初期化異常) る。
E 6 2 1 1 レンズオーバーヒート(PITCH) 光学手振れ補正ブロックのホール素子(PITCH)(SY-173
基板CN402 5,6ピン)を点検する。異常なければ
PITCH角速度センサ(SY-173基板SE502)周辺の回路を点
検する。
E 6 2 1 2 レンズオーバーヒート(YAW) 光学手振れ補正ブロックのホール素子(YAW)(SY-173
基板CN402 ql,w;ピン)を点検する。異常なければYAW
角速度センサ(SY-173基板SE501)周辺の回路を点検す
る。
E 6 2 2 0 サーミスタの異常。 光学手振れ補正ブロックのサーミスタ(SY-173基板CN402
4ピン)を点検する。
E 9 1 0 1 フラッシュの充電異常。 フラッシュユニットを点検または交換する。(Note)
E 9 2 0 0 規定外の充電池が使用された。 規定の充電池を使用する。
Note:交換後は,必ず「1-3. フラッシュエラー発生時の対処法」を行って下さい。
DSC-W80/W85_L2
1-6
ENGLISH JAPANESE
1-3. フラッシュエラー発生時の対処法
本機はフラッシュエラー(自己診断コードE:91:01)が発生した場合,高電圧による異常を防止するために自動的にフラッシュ
充電および発光禁止の設定になります。
フラッシュエラー発生後はエラーの解除を行う必要があります。エラーの解除はホーム画面から初期化操作を実行することによ
り行います。
設定リセット
お買い上げ時の設定に戻します。
[設定リセット]を実行しても、内蔵メモリーに記録されている画像は削除されません。
1 コントロールボタンの / / / で[設定リセット]を選び、中央の を押す。
「全ての設定内容をリセットします」というメッセージが表示される。
2 で[実行]を選び、中央の を押す。
設定リセットが実行される。
設定リセットを中止するには
手順 2 で、
[キャンセル]を選び、中央の を押す。
設定リセット中は電源が切れないようにご注意ください。
1-4. 内蔵メモリのデータコピーおよび消去方法
内蔵メモリのデータコピーまたは消去はホーム画面の操作から実行可能です。(消去する場合は内蔵メモリの初期化を行いま
す。)
Note1: SY-173基板交換の際は,基板交換前に内蔵メモリのデータを消去して下さい。
Note2: SY-173基板交換の際は,基板交換後に内蔵メモリのフォーマットおよび初期化を実行して下さい。
内蔵メモリのコピー方法
コピー
内蔵メモリーに記録した画像を、“メモリースティック デュオ” に一括コピーします。
内蔵メモリのフォーマット方法
“メモリースティック デュオ” が本機に入っている場合は表示されません。
フォーマット
内蔵メモリーの管理領域をフォーマット
(初期化)
します。
フォーマットすると、プロテクトしてある画像も含めて、すべてのデータが消去され、元に戻せ
ません。
フォーマットを中止するには
手順 2 で、
[キャンセル]
を選び、中央の を押す。
DSC-W80/W85_L2
1-7
ENGLISH JAPANESE
1-5. 内蔵メモリへデータを書き戻す方法
通常は,PCからカメラの内蔵メモリへデータを書き込むことはできない設定になっています。
基板交換後などに,内蔵メモリへデータを書き戻す場合には,この設定を一時的に変更する必要があります。
設定の変更には,書き込み許可ツール(WriteEnableTool.exe)を使用します。
書き戻し方法
1) カメラとPCをマスストレージ接続し,ドライバを“Sony Seus USB Driver”に切り替える。
2) 書き込み許可ツールとSeusEXを起動する。
3) 書き込み許可ツールの[Activate Write Enable Mode]ボタンをクリックする。
4) 設定の変更が終了すると,次のメッセージが表示されます。
5) ドライバを元に戻して、カメラとPCをマスストレージ接続する。
6) PCに読み出しておいたデータをカメラの内蔵メモリに書き込む。
7) カメラとPCの接続を解除し,カメラの電源をOFFにする。
注意: カメラの電源をOFFにすることにより,書き込み許可の設定が解除されます。
DSC-W80/W85_L2
1-8E
2. DISASSEMBLY
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Cut and remove the part of gilt
Do not insert the cable insufficiently nor crookedly. which comes off at the point.
(Be careful or some
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped. pieces of gilt may be left inside)
DSC-W80/W85_L2
2-1
2-1. IDENTIFYING PARTS
SW-494 Board
Release Block Cabinet (Rear)
⋅ RL-071/078 Board
BT Holder
MC-176 Board
SY-173 Board
LCD Module
Main Frame
Cabinet (Front)
Lens Block
Flash Unit ⋅ Barrier Block
⋅ ST-160 Board ⋅ Zoom Gear Block
- DISASSEMBLY FLOW -
2-2-3. LCD/BT HOLDER SECTION 2-3. EXCHANGE METHOD OF 2-4. EXCHANGE METHOD OF
⋅ BT Holder BARRIER BLOCK ZOOM GEAR BLOCK
⋅ Flash Unit
⋅ LCD Module
⋅ Main Frame
⋅ SW-494 Board
DSC-W80/W85_L2
2-2
HELP
2-2. DISASSEMBLY
EXPLODED VIEW HARDWARE LIST
2-2-1. CABINET SECTION
Follow the disassembly in the numerical order given.
1 Cabinet (Front) (1-1 to 1-8)
2 Cabinet (Rear) (2-1 to 2-2)
1-6 (#65)
1-7 (Open)
1-4 (#65)
HELP
2 Cabinet
(Rear)
2-2 (#65)
1-8
(Claw) 1-1 (#65)
DSC-W80/W85_L2
2-3
2-2-2. MAIN BOARD SECTION
Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST
1 Release Block (1-1 to 1-3)
2 Lens Block (2-1 to 2-5)
3 SY-173 Board (3-1 to 3-11)
R:1 kΩ/1 W
(Part code: 1-215-869-11)
ST-160 Board
C901
Flash Unit
1-1
LCD/BT Holder
1 Release Block Section
(See Page 2-5)
2-3
(Release the claw
that is the fixation
1-2 of the flash unit
(Claw) once)
1-3 3-7 (Claw)
HELP 3-1
3-2
3-11
3-6
2-1
(Claw)
3-3 3-9
2-2
SY 3-8
-17
3 (#5)
3-4
(Solder)
3-5 HELP 2-4
(#3) 2-5
3-10
2 Lens Block
(See Page 2-6, 2-8)
3 SY-173 Board
DSC-W80/W85_L2
2-4
2-2-3. LCD/BT HOLDER SECTION
Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST
1 Flash Unit (1-1)
2 LCD Panel/SW-494 Board (2-1 to 2-4)
3 BT Holder (3-1 to 3-3)
2 LCD Panel/
2-1 SW-494 Board
(#5)
SW
-49
4
HELP
2-4
(Claw)
2-3 HELP
(Claw)
3-2
2-2 1-1
(Claw) (Claw)
HELP 3 BT Holder
1 Flash Unit
DSC-W80/W85_L2
2-5
2-3. EXCHANGE METHOD OF BARRIER BLOCK
Tweezers
Barrier tape
3 Solvent 4 Ornamental ring (A) Barrier block
2 Barrier block
2 Inner ring
1 Two screws
DSC-W80/W85_L2
2-6
2-3-3. HOW TO INSTALL THE BARRIER BLOCK
CAV No.
1 Inner ring
2 Two screws
1 Barrier tape
Boss
1 Barrier tape
Note: Turn on and off the power to check the opening and closing of the barrier block with the camera
in horizontal, up and down directions respectively.
Further, check the zoom motion.
Rotate the ornamental ring (A) lightly to check that it is not removed.
DSC-W80/W85_L2
2-7
2-4. EXCHANGE METHOD OF ZOOM GEAR BLOCK
Note: Do not hold the part of terminal and the part of spring.
OVF
Screw
Connector
2 Shutter flexible board Hook
Connector
3 Vibration-proof flexible board
DSC-W80/W85_L2
2-8
5 Peel the adhesive sheet (upper) that secures the main flexible board.
6 Disengage the main flexible board from the hook of the ring assembly, and then slide the main flexible board
to remove.
7 Peel the adhesive sheet (lower) that secures the main flexible board.
* The FOCUS motor must remain soldered.
Hook
Ring assembly
qa Nuruto gear
8 Four screws
Rear
assembly
Hook
q; Z leaf
Boss spring Ring assembly
DSC-W80/W85_L2
2-9
• HOW TO REMOVE THE ZOOM GEAR BLOCK
1 Unsolder the zoom motor.
2 Remove the FG leaf spring.
3 Remove the main flexible board from the zoom gear block.
4 Remove the zoom gear block.
Rear assembly
1 Solder Hook
2 FG leaf spring
Rear assembly
1 Solder Hook
3 FG leaf spring
DSC-W80/W85_L2
2-10
4 Apply the lubricant (SRX-4339) to the nuruto gear, and insert it into the ring assembly.
* Rotate the gear in the ring assembly in the arrow direction until the end of the gear is not engaged
with a concave portion of the ring assembly (because a convex portion of the rear assembly enters
the convex portion).
Ring assembly
4 Nuruto gear
8 Check that the projection of the nuruto shaft that protrudes from the rear assembly is within the
specified value given below.
* Specified value: 0.005 – 0.395mm
Hook
Ring assembly
Boss 6 Vibration-proof
flexible board
Boss
7 Four screws
Nuruto shaft B
Nuruto shaft
0.005 – 0.395mm
DSC-W80/W85_L2
2-11
9 Secure and connect the main flexible board.
Z leaf
spring
Ring assembly
Hook
q; Secure and connect the vibration-proof flexible board and the shutter flexible board respectively.
Connector
Hook
Shutter flexible board
Connector
Bousin flexible board
DSC-W80/W85_L2
2-12
qa Install the OVF.
*When installing the OVF, fit a projection of OVF in the groove of the ring assembly.
OVF
Projection
Ring assembly
Groove
Screw
Confirm the operation after installing the lens block in the set.
1 Power ON/OFF
2 Expansion and contraction confirming of lens and opening and shutting confirmation of barrier.
Confirm there are neither dirt nor wounds in the surface of the ornamental ring (A) and lens
if there is no problem in operation.
Wipe off when dirty.
3 Confirm the operation with Wide/Tele.
Note: Do not be of caught etc.
Do not allophone.
DSC-W80/W85_L2
2-13E
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
SY electrostatic sheet
BT holder
Main frame
DSC-W80/W85_L2
HELP
INSTALLATION METHOD OF BATTERY TERMINAL BOARD
1 Insert the battery terminal board into a slit in the BT holder to install.
* The battery terminal board is attached with the notch for installation.
BT holder
Notch
Battery terminal
board
Harness (Red)
DSC-W80/W85_L2
HELP
3. BLOCK DIAGRAMS
Link
DSC-W80/W85_L2
3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
LENS BLOCK CD-701 FLEXIBLE BOARD SY-173 BOARD (1/2) LCD901 (1/2)
LCD MODULE
AB19-AB21, AC18-AC21,
AE18-AE21, AF19-AF21
G1-G3, H1-H3, J1
(METER) CN713
3 - 10
IC004 CCD_OUT
17 10 14 6 H10 CA_AD00 - CA_AD13 LCD_D0 - LCD_D7 D0 - D7
BUFFER
IC003
7M CCD
IMAGER
11 - 13
H1A,H2A,H1B,H2B CA_HD LCD_CK, LCD_HD, LCD_VD DCLK, HSYNC, VSYNC
CCD SIGNAL A2 CA_FD
AE23 2.5INCH
PROCESS, A3 AF22 COLOR
SHUTTER ZOOM FOCUS IRIS TIMING GEN_TG_CLK XCS_ PANEL SPENA LCD
A4 AF18 U19 36
MOTOR MOTOR MOTOR MOTOR RG GENERATOR XDD_SYS_RST RESET Z
19 34 K4 IC211 37
(1/10)
M M M M X201 (1/2)
35, 34
33.75MHz IC202 1 IC_211_2_SO, XIC_211_2_SCK SPDA, SPCK
CPU
1, 3, 6-12,
GENERATOR GEN_SYS_CLK
14-16
V5A, V5B, V6 - V10 5 Y12
(6/10)
FOCUS
RESET
E18, B23
RL-071/078
F3, E3
Q301 E7 BOARD (1/2)
XCS_AUDIO CN707 CN101
VSUB_CONT_PRE, V8 E4
(1/2) (1/2)
R7, AF25
VSUB_CONT_POST
Q302 IC_211_AUIN MIC_SIG 1 MIC_SIG
AF8 E6 B6 1 MIC901
IC401 IC603
XLENS_DRIVER_PS
A5, A2
LENS DRIVE D4 H11 IC_211_AUOUT SP± SP901
AE8 E5 AUDIO AMP
(2/10) (7/10) SPEAKER
CN402
MC-176 BOARD
50, 49
D2, B1
Y18, Y17
D3, F1
ND(±) ND_± IRIS MOTOR IRIS_M_IN, IRIS_M_BRK_2B
DRIVER
(1/2)
CN710 CN101
(1/2) (1/2)
AU_LINE_OUT 7 A_OUT_L
B4, B5
Z_DC_MOTOR(±) ZOOM_A, ZOOM_A- ZM_DIR_A, ZM_EN_A, ZM_BRK_B (7/10)
MOTOR
DRIVER
Q242 - Q244 Q241
IC_211_CVOUT IC_211_YOUT HD Y 3 HD Y CN102
SHUTTER
G1, E4
48 - 45
F4, F3
R8, AE25
SHUTTER(±) SHUTTER_± MSHUT_DIR, MSHUT_EN AB13 28 24 (1/2)
MOTOR VOUT_1 IC_211_PBOUT HD Pb 14 HD Pb
DRIVER AF12 BUFFER CLAMP 17 4 MULTI
VOUT_2 IC_211_PROUT HD Pr 16 HD Pr CONNECTOR
AC12 15 2
F_PI_SENS_OUT FC_SENS
ZOOM 22 Y10
ZOOM XFC_RST_LED XFC_RST_LED XHD_EN
FG RESET 23 M8 V7
SENSOR
Z_PI_SENS_OUT ZM_SENS_1ST 10, 9
41 AD26
21, 22
10, 12
Y1, AA1
Y11, W11
24, 28
XZM_FG_LED XZM_FG_LED
26 L8
USB_VBUS 12 USB_VBUS
19 6
LENS_ID 44
LENS_ID
D9 2
OVERALL (2/2) CN704
LENS TEMP THERM LENS_TEMP (PAGE 3-2) XMS_IN
40 AE3 6
SENSOR
MEMORY
2 - 5, 7, 8
A13 - A15,
STICK
B13 - B15
OPTICAL IMAGE MSX_D0 - MSX_D3, MSX_CLK, MSX_BS DUO
OIS TEMP THERM TZ_HALL_TEMP
STABILIZER SENSOR
4 AF3
SE501
G6, J8, J9, J7 B10, D10
15 - 12
HALL YAW_HALL_±
D6, D5
25, 24
STABILIZATION CA_FD
HALL PITCH_HALL± C9
ELEMENT DRIVE XDD_SYS_RST XDD_SYS_RST
(3/10)
A7
1
A4, B4, B5
A : VIDEO SIGNAL
IC_211_0_SO, IC_211_0_SI, XIC_211_0_SCK OVERALL (2/2)
(PAGE 3-2) A : AUDIO SIGNAL
CLK_IC_503 A : VIDEO/AUDIO SIGNAL
A3 W13
XCS_IC_503
A5 U8
XIC_211_IC_503_RST
A6 H10
05
DSC-W80/W85_L2
3-1
3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
S102
23, 25
11 -13
3 XPWR_ON XPWR_ON XPWR_ON ACV_UNREG 18 - 20 ACV_UNREG
POWER 3 B8 UNREG
XDIRECT_PB
B7 ST_UNREG
Q004, XACV_DET 24 XACV_DET
Q013 7 19
D101 4 X_PWR_LED XPWR_LED
4 CAM_12V D002
(POWER)
17, 21
8 - 10
CAM_-7.5V CHARGE_V 21 - 23 CHARGE_V
TI_5.0V
MAX_5.0V IC001
SW-494 BOARD D_3.0V CN102
DC/DC
A_3.0V CONVERTER (2/2)
S003 CN001 CN708 J5 (9/10) MULTI
8 XDIRECT_PB XDIRECT_PB X101 DDR_1.8V CONNECTOR
N 5 D_1.8V
32.768kHz
J4 D_1.2V
S001, S002, BL_H
S004 - S010
FUNCTION 6, 7 KEY_AD1, 2 KEY_AD_1, 2
KEY 7, 6
D003
Q101 IC101 XACV_IN
S011 K8
FRONT
MODE 12, 11 MODE_DIAL1, 2 MODE_DIAL1, 2 XMS_IN XACC_IN XACC_IN 1 XACC_IN
2
1, 2
C6 CONTROL G9 30 26
DIAL (8/10) UART Rx,
D26, G19
IC_211_1_UI, IC_211_1_UO UART Rx, UART TX 25, 26
15, 9
UART Tx
6, 5
OVERALL (1/2) USB_VBUS
D001 (PAGE 3-1) D8
AE/AF LOCK/ 4 XAE_LOCK_LED XAE_LOCK_LED
SELF-TIMER 9
D002
FLASH CHARGING/ 5 XSTRB_LED XSTRB_LED XPWR_OFF
RECORD 8 B9 G8
XIC_211_RST_REQ
A1 W12
LCD901 (2/2) 1 VL_3V VL_3V IC102 XDD_SYS_RST
BT001 12 3 5 D7 B4 AB18
LCD MODULE BACK UP VCC
LITHIUM 2 4 A9
BATTERY (8/10) XCS_FR
BACKLIGHT D101 E2 A23
D1, D2, E1
XDD_SYS_RST
1 IC211
(2/2)
OVERALL (1/2) IC_211_0_SO, IC_211_0_SI, XIC_211_0_SCK CPU
(PAGE 3-1) (4/10, 5/10)
XAE_LOCK_SW
N19
XSHUT_SW
R19
MODE_DIAL1, 2
XPWR_LED
Y9
XAE_LOCK_LED
W9
ST-160 BOARD XSTRB_LED
W8
CN001 CN701
D002 XAF_LED 12 AFLED_CONT
AF LED
SELF-TIMER/ 12 CONTROL G15
AF ILLUMINATOR
T001 Q704
D001 D706
XE_A(H) H8
3 2 ST_UNREG (MS ACCESS)
+
4 1
TRIGGER
FLASH
UNIT TRIG_GND
C901
CHARGING STRB_CHG 8 STRB_CHG
CAPACITOR 15 IC001 10 8 V2
XSTRB_FULL 9 XSTRB_FULL
XE_K(L) 9 9 H9
1, 2
05
DSC-W80/W85_L2
3-2
3-3. POWER BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
23, 25
ACV_UNREG 18-20 MS_VCC
11-13
ACV_UNREG MEMORY
IC001 B+ SWITCH 9 STICK
DUO
DC/DC CONVERTER
Q004, 013 (9/10)
MS_PWR_ON
F
XACV_DET 24 XACV_DET 28 GD
19 7 POWER (2/2)
CN102 ST_UNREG
D002 45 BATT (PAGE 3-4)
MULTI D003
CONNECTOR L009 D_1.2V
13 PVSD LXSD 16
DDC1P2_EN
17, 21
8-10
ONSD 15
D007 CAM_12V
29 PVBST LXBST 31
L004
XPOWER_ON 27 XPOWER_ON SWBST 30
7 4
ONBST 22
D010 CAM_-7.5V
LXINV 21
PVINV 20
XPWR_ON
CAMDD_EN
ONINV 1
XACV_IN
BT901
BATTERY
TERMINAL IC201
L001 A_3.0V
BATTERY
BATT_UNREG PVM 4
+ AUTHENTICATION
(6/10)
E LXM 5
L005 D_3.0V
DDC2P9_EN
IC_211_1_SI POWER (2/2) ONM 3
BATT_SIG P144_SOA0 D5 (PAGE 3-4)
S E4 TXRX IC_211_1_SO
P143_SIA0 C5 D006 BL_H
XIC_211_1_SCK 35 PVLED LXLED 33
P142_XSCKA0 B5 L003 Q006
XCS_IC_201 SWLED 34
– P120_INTP0 B1 BACKLIGHT BL_L
FBLLED 37
BL_EN1 CONTROL
ONLED 36
D_3.0V BL_EN2
B2 XRESET
D011
L007 Q003
MAX_5.0V
47 LXSU SU 43 B+ SWITCH
IC106 PVSU 44 DDC5PSW_EN
VSU_EN
RESET (8/10) ONSU 46
A XDD_SYS_RST
D102
1 OUT Vdd 4
POWER (2/2)
L006
G
(PAGE 3-4) 9 PVAFE LXAFE 8
DDC1P8_EN POWER (2/2)
IC101 ONAFE 10
(PAGE 3-4)
FRONT CONTROL
(8/10) Q014
B+ SWITCH
BATT_SENS H8
D_3.0V DDCPV_EN
DDC2P9_AD H7
A9 CS D_1.8V
DDC1P8_AD J7
B4 XSYS_RST
BACK_UP_VCC
IC002 5V REG
(9/10)
DDC1P2_EN L002
DDC1P2_EN D9 9 SW TI_5.0V
CAMDD_EN VOUT 2
CAMDD_EN B2 6 VBAT
DDC2P9_EN
DDC2P9_EN E9 7 LBI
EVER_PSB D_3.0V
1 EN PS 8 D_1.8V D_1.8V
BL_EN1
BL_EN1 F8
BL_EN2
BL_EN2 F9
DDC5PSW_EN SW_1P8_EN Q007
DDC5PSW_EN F7 1.8V/3.0V
VSU_EN
VSU_EN J8 DISCHARGE
B XIC_211_RST_REQ
XPWR_OFF
A1 XRESET_REQ
DDC1P8_EN E8
DDC1P8_EN IC003 1.8V REG Q010, 012
DDCPV_EN (9/10) B+ SWITCH
B9 XPOWER_OFF
POWER (2/2) DDCPV_EN C9
EVER_PSB DDR_1.8V
(PAGE 3-4) EVER_PSB J9 B2 Vin Vout B1
SW_1P8_EN Vcont
SW1P8_EN J1
LDO_1P8_EN A2
LDO1P8_EN H2 BACK_UP_VCC
C XPWR_ON
XDIRECT_PB
B8 XPOWER_ON0 DISW1P8_EN C2
DISW1P8_EN LDO_1P8_EN
B7 XPOWER_ON2 DISW2P9_EN DISW1P8_EN
POWER (2/2) DISW2P9_EN C1
(PAGE 3-4) DISW2P9_EN
VL_3V
Vin 4
1 Vout
Vsen 3
05
DSC-W80/W85_L2
3-3
3-4. POWER BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
LCD901
SY-173 BOARD (2/2) LCD MODULE
CN713
D_1.8V FB702 VDDD
31
VDD
L701 32
D_3.0V PVDD 2.5INCH
18
IC501 COLOR
XDD_SYS_RST RESET Z LCD
2.8V REG 37
(3/10) IC506
A_3.0V PITCH/YAW SW-494 BOARD
B2 Vin Vout B1 SENSOR AMP
CN708 CN001 BACKLIGHT
Vcont (3/10)
IC502 BL_H BL_H 10 BL_H
A2 3
1.5V REG BL_L BL_L 9 BL_L
(3/10) SE502 4
VL_3V VL_3V 1
PITCH 12 BT001
D_1.8V SENSOR LITHIUM
B2 Vin Vout B1
IC503 BATTERY
OPTICAL SE501
D_3.0V IMAGE YAW D001
MAX_5.0V STABILIZATION SENSOR D_3.0V 3 AE/AF LOCK/
10 SELF-TIMER
DRIVE
(3/10)
S003 D002
A XDD_SYS_RST
A7 RESET_N
XDIRECT_PB
5
8 FLASH CHARGING/
ST_UNREG XIC_211_IC_503_RST RECORD
POWER (1/2) A6 XDL
(PAGE 3-3)
D_1.2V C
XDD_SYS_RST
POWER (1/2) RL-071/078 BOARD
CAM_12V
(PAGE 3-3) CN707 CN101
CAM_-7.5V S102
XPWR_ON 3
3 POWER
1, 2
AU_AVCC AUDIO AMP
(PAGE 3-3) B2 Vin Vout B1 UNIT
(7/10) TI_5.0V TI_5.0V 3
3
IC601 H10 GPE_09 R601 Q710
TI_5.0V 2.9V REG IC602
AB18 XRESET MAX_5.0V AF LED AF_5.0V 11
(7/10) VIDEO AMP 11
DRIVE D002 IC001
D601 (7/10)
SELF-TIMER/ FLASH CONTROL,
A_3.0V AF ILLUMINATOR CHARGE CONTROL
R723 D706
D_1.8V AF LED XAF_LED 12
R253 (MS ACCESS) Q704 12
DDR_1.8V CONTROL
L241
AFLED_CONT
VL_3V D_3.0V TPU2_OUT G15
CD-701 FLEXIBLE
IC305 12V REG
(1/10) BOARD
D_1.2V R254 L201 CN301
D_3.0V IC202 CAM_12V FB313 L301 CAM_12V
DDR_1.8V 5 Vin Vout 4 1
D_1.8V CLOCK IC003
D_1.8V GENERATOR
IC211
(6/10) L302 7M
FB282 CPU CAM_-7.5V CAM_-7.5V CCD IMAGER
L211 36
(4/10)
FB283 (5/10) CAM_3.2V FB307
(6/10)
3.2V REG Q303
IC306 (1/10) -7.5V IC004
DISCHARGE
TI_5.0V CAM_3.2V BUFFER
B2 Vin Vout B1
Vcont
A2
D DDC2P9_EN FB310
POWER (1/2) D_3.0V FB311
B XIC_211_RST_REQ
XPWR_OFF
W12 XRESET_REQ (PAGE 3-3)
G8 GPE_00 IC304 LENS BLOCK
POWER (1/2)
(PAGE 3-3) CCD SIGNAL
IC308 PROCESS, Q401 CN402
TIMING GENERATOR R402 Z_PI_SENS_Vcc ZOOM
XACV_IN 2.8V REG B+ SWITCH 42 RESET
K8 GPE_05 (1/10)
(1/10) SENSOR
E IC_211_1_SI
XZM_RST_LED
G18 SIO1_RXD
IC_211_1_SO 6 Vin Vout 4 R412 Z_BOX1_PI_SENS_Vcc
POWER (1/2) B24 SIO1_TXD 27
XIC_211_1_SCK ZOOM
(PAGE 3-3) H18 SIO1_SCK Z_BOX2_PI_SENS_Vcc FG
XCS_IC_201 Q305 25
W20 GPS_04 2.8V/3.2V R411
DISCHARGE
R401 F_PI_SENS_Vcc FOCUS
21 RESET
F MS_PWR_ON
T7 GPE_15 GPE_03 J8
XZM_RST_LED XDD_SYS_RST SENSOR
C1 RESET
POWER (1/2)
(PAGE 3-3) D_3.0V
MAX_5.0V
IC401
A_3.0V
LENS DRIVE
(2/10)
05
DSC-W80/W85_L2
3-4
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
12 1
CN001
MIC901
SW-494 MICROPHONE
BLOCK
BOARD
FLASH UNIT
RL-071/078 BOARD
LCD901
LCD MODULE
CN101 Note: CN101 is no mount.
1 8 (Direct solder)
RED
BLK
2.5INCH
C901 BACKLIGHT COLOR
CHARGING CAPACITOR LCD
1 12 39 1 CN707 BT901
CN701
CN708 38
CN713 2 8 1 BATTERY
FLEXIBLE FLAT CABLE 12 1 TERMINAL 39
(FFC-093)
RED
WHT
BLK
IC003
(Not supplied)
11
39
38
1
CN301
CN704
MEMORY STICK LOCK
CONNECTOR
1
51
50
10
IC211
12
(Not supplied)
CN402
LENS BLOCK
2
1 30
1
CN710
RED
BLK
FLEXIBLE FLAT CABLE
LEVEL3 LEVEL3
SY-173 BOARD SY-173 BOARD
(FFC-095)
SP901
(SIDE A) SPEAKER
(SIDE B)
30 1
26 2 CN101
Note: CN101 is no mount.
25 1 (Direct solder)
28 27
CN102
MC-176 BOARD (SIDE B)
MULTI CONNECTOR
DSC-W80/W85_L2
4-1 FRAME
4-2. SCHEMATIC DIAGRAMS
Link
DSC-W80/W85_L2
4-2. SCHEMATIC DIAGRAMS
Magenta
White
curve B, unless otherwise noted.
Cyan
Green
• Signal name
Red
Blue
XEDIT → EDIT PB/XREC → PB/REC
• 2: non flammable resistor
• 5: fusible resistor
• C: panel designation
• A: B+ Line
• B: B– Line A B A=B B A
• J : IN/OUT direction of (+,–) B LINE. Fig. a (Video output terminal output waveform)
• C: adjustment for repair.
• A: not use circuit
Electronic beam
(Measuring conditions voltage and waveform)
scanning frame
• Voltages and waveforms are measured between the
measurement points and ground when camera shoots CRT picture frame
color bar chart of pattern box. They are reference values
and reference waveforms.
(VOM of DC 10 MΩ input impedance is used)
• Voltage values change depending upon input
impedance of VOM used.) Fig.b (Picture on monitor TV)
Precautions for Replacement of Imager When indicating parts by reference number, please
• If the imager has been replaced, carry out all the adjustments include the board name.
for the camera section.
The components identified by mark 0 or dotted line with
• As the imager may be damaged by static electricity from
mark 0 are critical for safety.
its structure, handle it carefully like for the MOS IC.
Replace only with part number specified.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light. Les composants identifiés par une marque 0 sont
critiques pour la sécurité.
Ne les remplacer que par une pièce portant le numéro
spécifie.
DSC-W80/W85_L2
4-3
Schematic diagrams of the CD-701 flexible and SY-173 boards are not shown.
Pages from 4-5 to 4-15 are not shown.
DSC-W80/W85_L2
1 2 3 4 5 6 7 8 9 10 11 12
A MC-176 BOARD
MULTI CONNECTOR
XX MARK:NO MOUNT
B ACV_GND 30
ACV_GND 29
ACV_GND 28
XPOWER_ON 27
UART TX 26
UART Rx 25
XACV_DET 24
CHARGE_V 23
CHARGE_V 22
C CHARGE_V 21
ACV_UNREG 20
ACV_UNREG 19
ACV_UNREG 18
SY-173 REG_GND 17
(10/10)
CN710 HD Pr 16 CN102
Through the (MULTI CONNECTOR)
REG_GND 15
flexible flat cable To AV/USB multi cable
(FFC-095) HD Pb 14
D Page 4-15
REG_GND 13
of Level 3
USB_VBUS 12 2 HD Pr ACV_GND 1
USB_GND 11 4 HD Pb ACV_GND 3
AU_LINE_OUT 7 12 USB_DM
A_GND 6 14 USB_GND
E V_LINE_OUT 5 16 A_OUT_L UART Rx 15
HD Y 3 20 V_OUT XACV_DET 19
XACC_IN 1 24 HD Y ACV_UNREG 23
26 XACC_IN ACV_UNREG 25
F
Note:CN101 is not mounted.Flexible flat cable (FFC-095) is
soldered to this location instead. LND102 STATIC_GND
This FFC-095 is not supplied, but this is included in
MC-176 complete board.
05
DSC-W80/W85_L2
4-16 MC-176
• Refer to page 4-3 for mark 0.
1 2 3 4 5 6 7 8 9 10 11 12
A SW-494 BOARD
CONTROL SWITCH
XX MARK:NO MOUNT
B
CN001 XX BT001
LITHIUM
VL_3V 1 BATTERY
REG_GND 2
D001
D_3.0V 3 SML-510MWT86S
(AE/AF LOCK/SELF-TIMER)
XAE_LOCK_LED 4
SY-173 D002
R001 RB003
(10/10) XSTRB_LED 5 SML-310YTT86
2200 2200
CN708 (FLASH CHARGING/RECORD) 1 2
KEY_AD1 6 3 4
Through the
C flexible flat cable
(FFC-092)
KEY_AD2 7
5
7
6
8
MODE_DIAL1 12
4 3 4 3 4 3 4 3 4 3
S001 S004 S006 S008 S010
LCD901(2/2)
4 5
D BACKLIGHT
LND002 D005 (SELF-TIMER) (FLASH) (DISP) R005 (MACRO) (SET)
XX 2200
BL_L
32 1
BL_H
LND003 1 2
3 4
D003 D004 5 6
LND001 XX XX 7 8
STATIC_GND RB001
2200
STATIC_GND
LND004
E 2 1 2 1 2 1 2 1
4 3 4 3 4 3 4 3
S002 S005 S007 S009
W (ZOOM) T MENU HOME
AUTO
15 3
AUTO
4
16 HIGH SENS
5
SOFT SNAP
6
F 1
TWILIGHT PORTRAIT
7
1
3
2
4
COM TWILIGHT 5 6
8 7 8
2 LANDSCAPE R006
9 2200 RB002
COM LANDSCAPE 2200
10
BEACH 2 1
11
17 SNOW
12 4 3
MOVIE
18 13 S003
PROGRAM AUTO
14
R007
G S011
(MODE DIAL)
2200
05
DSC-W80/W85_L2
4-17 SW-494
• Refer to page 4-3 for mark 0.
1 2 3 4 5 6 7 8 9 10 11 12
A ST-160 BOARD
FLASH DRIVE
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
B CN001 12P
L001
2.2uH
T001
D001
MA2YF8000LS0 LND019
ST_UNREG 1 2 3 XE_A(H)
LND015
ST_UNREG 2 C007 R006
220p 4700 CHARGE+
TI_5.0V 3
1 4 R004 LND017
1M
SY-173 STRB_ON 4 C901
TRIGGER
49u
(10/10) STB_CHG_CNT 5 315V FLASH
CN701 C001 CHARGING TRIG_GND UNIT
REG_GND 6 22u LND016
Through the D003 CAPACITOR C004 LND018
flexible flat cable REG_GND 7 CHARGE- 0.047u
RB520S-40TE61
(FFC-093) 250V LND020
C Page 4-15
of Level 3
STRB_CHG 8
5 1
262
XE_K(L)
XSTRB_FULL 9
NC 10 6 2
AF_5.0V 11 7 3
HGND
N.C
VBATT
N.C
N.C
CY25BAJ-8F-T23-G02
FLASH DRIVE
D C005 C002
XX 1u
12
1
SW PGND
4.1
4 3 IC001 R003
11
2
5 2 SW PGND 100
FLASH CONTROL, R005
6 1 5 CHARGE CONTROL XX
0
10
D002 IC001
3
VCC CHG
CL-360S-TD4-X-TL TPS65552RGTR
0 3.1
SELF-TIMER/
4
9
F_ON XFULL
AF ILLUMINATOR
C006
XX
E
G_IGBT
I_PEAK
N.C
N.C
5 6 7 8
0 0
CL001
05
DSC-W80/W85_L2
4-18 ST-160
1 2 3 4 5 6
A
RL-071/078 BOARD Note:In this set, either RL-071 or RL-078 board is used.
All mounted parts and schematic diagram
CONTROL SWITCH,MIC are common to both RL boards. MIC901
MICROPHONE
XX MARK:NO MOUNT LND101
BLOCK
MIC_GND
MIC_SIG
LND102
B 2 1
S102
POWER
4 3
CN101 XX
MIC_SIG 1
MIC_GND 2 D101
SY-173 SML-412MWT86
(10/10) XPWR_ON 3 (POWER)
CN707
X_PWR_LED 4
Through the
C flexible flat cable
(FFC-094)
D_3.0V 5
REG_GND 6
Page 4-15
of Level 3 XSHUTTER_SW 7 S101
XAE_LOCK_SW 8 (SHUTTER)
6 5 C001 C002
0.047u 0.047u
4 2
1 3
D
Note:CN101 is not mounted. Flexible flat
cable (FFC-094) is soldered to this
location instead.
LND103 STATIC_GND
E LND104 STATIC_GND
05
DSC-W80/W85_L2
4-19 RL-071/078
4-3. PRINTED WIRING BOARDS
Link
DSC-W80/W85_L2
4-3. PRINTED WIRING BOARDS
4 1
DSC-W80/W85_L2
4-21
Printed wiring boards of the CD-701 flexible and SY-173 boards are not shown.
Pages from 4-23 to 4-25 are not shown.
DSC-W80/W85_L2
MC-176 (4 layers), SW-494 (2 layers)
: Uses unleaded solder.
>EP GW< 30 1
28 26 2 1 27
25 A
1-871-499- 1-871-499- 11 12
05 CN102 11 12 05
LND102
(MULTI CONNECTOR) Note: CN101 is not mounted. Flexible flat cable (FFC-095) is
soldered to this location instead.
Note: CN102 (multi connector) is not supplied, This FFC-095 is not supplied, but this is included in
MC-176 complete board.
but this is included in MC-176 complete board.
BT001
K A
(AE/AF LOCK/SELF-TIMER) CN001 +
D002
W (ZOOM) T
12 1
A
A D002
(FLASH CHARGING/RECORD)
3 1 3 1
S002 S005
Note: CN001 is not mounted. Flexible flat cable (FFC-092)
4 2 4 2 is soldered to this location instead.
2 8
1 7
LND003
BL-H RB001
TO LCD901 BT001
(BACKLIGHT) LITHIUM
BL-L BATTERY
B
15
16
LND002
13 14
4
B
5
12 2
N
S011
6
1
3
4
10 11
7
Note: S011 (mode dial) is not
S003
R007
8
18
17
9
(MODE DIAL)
RB002
7 1
R006
MENU 8 2
v
3
4
(DISP) C
S007
C RB003
2 4
2
2 8
1 7 S006
B
R005
b 1 3
2
3
3
4
4
S008
S010
S004
4
3
2
R001
D005 CAUTION
5
1
4
3
3 1
Danger of explosion if battery is incorrectly replaced. D
D A K S001 Replace only with the same or equivalent type.
3
4
D003
D004
K
4 2
1-871-501-
S009
V LND001
1-871-501- 11 12
2
DSC-W80/W85_L2
4-26 MC-176, SW-494
ST-160 (4 layers), RL-071/078 (2 layers)
: Uses unleaded solder.
LND103
6
2
3
R004
2
LND016
LND018 LND017
D101
C001
C002
S101
S102
C901
C007
R006
K A
D003
K
3 4
13
17 16
A
IC001
12
CHARGING D001
1
(POWER)
>EP GW<
A
K
-
+ T001
4
3
R005
C006
CAPACITOR
4
2 1
1
1-871-502- 12
5
4
9
8
S102
5
LND020
C002
LND015
+ C005 CL001
LND019 S101
05 (SHUTTER) POWER
1 11
C001
CN001
1-871-500-
B L001
2 12 11
12
05
1 2 3 MIC901
MICROPHONE
BLOCK
RL-071 BOARD (SIDE B) B R
ST-160 BOARD (SIDE B)
LND102 LND101
>EP GW<
B ST-160 B
-502-
1-871 8 1
3
CN101
D002
SELF-TIMER/
AF ILLUMINATOR
1-871-502- 12
1
B RL-071
LND104
1-871-500- 11
A
R003
R002
05
5
12
8
01
6
2
2
D101
S101
C001
C002
S102
K A
(POWER)
4
3
4
1
>EP GW<
1-874-109- 11
RL-078
S101 S102
POWER
05 (SHUTTER) A
MIC901
MICROPHONE
BLOCK
RL-078 BOARD (SIDE B) B R
LND102 LND101
>EP GW<
-109-
1-874 8
CN101
1
1-874-109- 11
B RL-078
LND104
05
DSC-W80/W85_L2
4-27 ST-160, RL-071/078
Mounted parts location of the SY-171 board is not shown.
Pages 4-29 and 4-30 are not shown.
DSC-W80/W85_L2
4-3. PRINTED WIRING BOARDS
DSC-W80/W85_L2
4-31E SW-494, ST-160
NOTE
A B C
LENS SECTION
RL-071/078 BOARD B
DSC-W80/W85_L2
5. REPAIR PARTS LIST
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from When indicating parts by reference number,
the original one. please include the board name.
• Items marked “*” are not stocked since they are seldom required for routine
service. Some delay should be anticipated when ordering these items. The components identified by mark 0 or
• The mechanical parts with no reference number in the exploded views are not dotted line with mark 0 are critical for safety.
supplied. Replace only with part number specified.
• Due to standardization, replacements in the parts list may be different from Les composants identifiés par une marque
the parts specified in the diagrams or the components used on the set. 0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
• CAPACITORS:
le numéro spécifié.
uF: µF
• COILS
uH: µH
• RESISTORS • Color Indication of Appearance Parts
All resistors are in ohms. Example:
METAL: metal-film resistor (SILVER) : Cabinet’s Color
METAL OXIDE: Metal Oxide-film resistor (Silver) : Parts Color
F: nonflammable
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , µPC... , µPC... ,
uPD..., µPD...
• Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
EE : East European model
HK : Hong Kong model
J : Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
TW : Taiwan model
DSC-W80/W85_L2
5-1
5. REPAIR PARTS LIST
5
4 7 6
#65
#65
#65
5
2
#65
#65
Main Board Section
(See Page 5-3)
#65 3
Ref. No. Part No. Description Ref. No. Part No. Description
1 X-2177-050-1 CABINET (FRONT) ASSY (W80: SILVER) 4 X-2177-063-1 CABINET (REAR) ASSY (W80: WHITE)
1 X-2177-051-1 CABINET (FRONT) ASSY (W80: BLACK/W85) 4 X-2177-064-1 CABINET (REAR) ASSY (W80: PINK)
1 X-2177-052-1 CABINET (FRONT) ASSY (W80: WHITE)
1 X-2177-053-1 CABINET (FRONT) ASSY (W80: PINK) 4 X-2177-065-1 CABINET (REAR) ASSY (W85)
* 2 3-197-910-01 SHEET, SY ELECTROSTATIC 5 3-099-626-01 SHEET, LCD WINDOW ADHESIVE
6 3-099-624-01 WINDOW, LCD
3 3-099-623-01 CABINET, SIDE 7 3-099-625-01 PLATE, MODE
4 X-2177-061-1 CABINET (REAR) ASSY (W80: SILVER) #65 2-635-591-01 SCREW (M1.4), NEW TRUSTAR P2 (Silver)
4 X-2177-062-1 CABINET (REAR) ASSY (W80: BLACK)
DSC-W80/W85_L2
5-2
5. REPAIR PARTS LIST
58
LCD/BT Holder Section
(See Page 5-4)
56 (Note 1)
57
ns MIC901
54 55
ns
53
(FFC-093) 61
#5
62 65
ns
#5
63
64 66
52
SY
-17 #30
3
#3
SP901
68
Lens Section (including IC003 (CCD imager) and
51 (See Page 5-5) CD-701 flexible complete board) (Note 2)
Note 1: In this set, either RL-071 or RL-078 board is used. Note 2: Be sure to read “Precuations for Replacement of
All mounted parts and schematic diagram are com- Imager” of level 3 on page 4-3.
mon to both RL boards.
Ref. No. Part No. Description Ref. No. Part No. Description
51 A-1253-161-A SY-173 BOARD, COMPLETE (SERVICE) 65 3-099-632-01 CABINET BOTTOM (W80: SILVER)
52 3-099-637-01 LABEL, FUSE 65 3-099-632-11 CABINET BOTTOM (W80: BLACK/W85)
* 53 3-099-634-01 SHEET, ST INSULATING 65 3-099-632-21 CABINET BOTTOM (W80: WHITE)
* 54 3-099-636-01 SHEET, RL INSULATING 65 3-099-632-31 CABINET BOTTOM (W80: PINK)
55 3-099-620-01 RETAINER, RELEASE 66 3-113-705-01 SHEET (PLUS), CD RADIATION
56 A-1246-054-A RL-071 BOARD, COMPLETE (Note 1) 68 A-1253-768-A CCD BLOCK ASSY (including IC003
56 A-1271-235-A RL-078 BOARD, COMPLETE (Note 1) (CCD IMAGER) and CD-701 flexible complete
57 1-833-618-11 CABLE, FLEXIBLE FLAT (FFC-094) board) (Note 2)
58 X-2177-054-1 RELEASE ASSY MIC901 1-542-721-11 MICROPHONE BLOCK
59 3-099-621-01 CABINET, UPPER SP901 1-826-614-21 LOUD SPEAKER (1.0CM)
#3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
60 3-099-622-01 SHAFT, STRAP #5 3-080-204-01 SCREW, TAPPING, P2 (Black)
61 A-1246-051-A MC-176 BOARD, COMPLETE
* 62 3-099-639-01 SHEET, MC RADIATION #30 3-086-156-11 SCREW B1.2 (White)
* 63 3-099-629-01 RETAINER, MULTI #65 2-635-591-01 SCREW (M1.4), NEW TRUSTAR P2 (Silver)
* 64 3-099-635-01 SHEET, MC INSULATING
DSC-W80/W85_L2
5-3
5. REPAIR PARTS LIST
105 BT001
LCD901
ns
107
108
104
#65
! : BT001 (BATTERY, LITHIUM
SECONDARY)
Board on the mount position.
(See page 4-26)
103
C901 ns
112
102
101 BT901 113
(Note) Note: Refer to HELP “Installation method of battery termi-
nal board” when changing the service terminal (BT).
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
• Refer to page 5-1 for mark 0.
Ref. No. Part No. Description Ref. No. Part No. Description
101 A-1246-052-A ST-160 BOARD, COMPLETE 111 1-833-616-11 CABLE, FLEXIBLE FLAT (FFC-092)
0 102 1-480-014-11 FLASH UNIT * 112 3-198-159-02 SHEET, BT TERMINAL
* 103 3-113-323-01 LABEL, MS CAUTION 113 X-2177-056-1 HOLDER ASSY, BT
104 3-099-631-01 SCREW, TRIPOD 0 BT001 1-756-710-11 LITHIUM RECHARGEABLE BATTERY
105 3-099-627-01 FRAME, MAIN BT901 A-1257-452-A TERMINAL, SERVICE (BT) (Note)
DSC-W80/W85_L2
5-4
5. REPAIR PARTS LIST
HARDWARE LIST
ns
151
#30
ns #30
155
(Note 2)
M901 (Note 2)
154 ns
(Note 1) 157
153 (Note 2)
ns
(Note 1)
152
(Note 1)
156 (Note 2)
#30
Note 1: Be sure to read “Exchange method of barrier block” Note 2: Be sure to read “Exchange method of zoom gear
on page 2-6. block” on page 2-8.
Ref. No. Part No. Description Ref. No. Part No. Description
151 A-1231-924-A LSV-1160A (SERVICE) 156 2-689-850-01 SPRING, FG LEAF (Note 2)
152 2-689-851-01 RING (A), ORNAMENTAL (Note 1) 157 X-2177-203-1 GEAR (S), NARUTO (Note 2)
153 2-691-890-01 TAPE, BARRIER (Note 1) M901 1-479-864-11 GEAR BLOCK, ZOOM (1160) (Note 2)
154 A-1205-001-A BARRIER BLOCK ASSY (Note 1) #30 3-086-156-11 SCREW B1.2 (White)
155 2-689-849-01 SPRING, Z LEAF (Note 2)
DSC-W80/W85_L2
5-5
Electrical parts list of the CD-701 board is
not shown.
Page 5-6 is not shown.
DSC-W80/W85_L2
MC-176 RL-071 RL-078 ST-160 SW-494
1-833-618-11 CABLE, FLEXIBLE FLAT (FFC-094) 0 T001 1-445-108-21 TRANSFORMER, D.C-D.C CONVERTER
DSC-W80/W85_L2
5-8
Ver. 1.1 2008.05
The changed portions from
Ver. 1.0 are shown in blue.
Battery Charger Battery Charger USB, A/V Cable for Power Cord
BC-CSGC BC-CSGC Multi-use Terminal 0 1-555-074-91 (AUS)
0 1-480-175-11 (J) 0 1-480-175-31 1-829-866-51 0 1-832-121-31 (CH)
0 1-480-175-21 (US, CND) (EXCEPT US, CND) 0 1-833-892-21 (KR)
0 1-827-269-12 (UK, HK)
0 1-824-910-71 (AEP, E)
0 1-792-549-41 (JE)
0 1-783-952-61 (AR)
Rechargeable Battery Pack Battery Case Wrist Strap (W80) Neck Strap (W85)
NP-BG1 (Note) 2-050-981-01 2-674-454-31
(Note)
Conversion (2P) Adaptor Conversion (2P) Adaptor Soft Carrying Case (W85)
0 1-569-007-12 (JE) 0 1-569-008-12 (E: NTSC) 3-106-988-01
DSC-W80/W85_L2
5-14
Ver. 1.1 2008.05
The changed portions from
Ver. 1.0 are shown in blue.
Instruction Manual
3-095-004-02 (JAPANESE) (W80: J)
3-095-004-12 (ENGLISH) (W80: CND, AEP, UK, E, HK, AUS, JE/
W85: CND, AEP, UK, E, AUS)
3-095-004-22 (FRENCH, ITALIAN) (W80: CND, AEP/W85: CND, AEP)
3-095-004-32 (SPANISH, PORTUGUESE) (W80: AEP, E, AR, JE/W85: AEP, E)
3-095-004-42 (GERMAN, DUTCH) (W80: AEP/W85: AEP)
3-095-004-52 (TRADITIONAL CHINESE, SIMPLIFIED CHINESE)
(W80: E, HK, CH, JE/W85: E)
3-095-004-62 (RUSSIAN) (W80: AEP/W85: AEP)
3-095-004-72 (ARABIC, PERSIAN) (W80: E/W85: E)
3-095-004-82 (KOREAN) (W80: KR, JE/W85: KR)
3-095-004-92 (POLISH, CZECH) (W80: AEP/W85: AEP)
3-095-005-12 (HUNGARIAN, SLOVAK) (W80: AEP/W85: AEP)
3-095-005-22 (SWEDISH, FINNISH) (W80: AEP/W85: AEP)
3-095-005-32 (NORWEGIAN, DANISH) (W80: AEP/W85: AEP)
3-095-005-42 (THAI, MALAY) (W80: E/W85: E)
3-095-005-52 (TURKISH, GREEK) (W80: AEP/W85: AEP)
3-095-005-62 (ENGLISH, SPANISH) (W80: US)
CD-ROM
(Cyber-shot Application Software/
“Cyber-shot Handbook”/ Cyber-shot Handbook (PDF)
“Cyber-shot Step-up Guide”)
The CD-ROM supplied contains all of language version of
3-094-911-02 (EXCEPT J)
the Handycam Handbook (PDF) for printing.
3-198-533-02 (J)
・ The printed matter is not supplied. If required, please
order it with the part number below.
・ (Only for destination Japanese model)
日本国内については日本語のみが印刷での部品供給可能です。
3-094-994-02 (JAPANESE) 3-094-995-42 (KOREAN)
3-094-994-12 (ENGLISH) 3-094-995-52 (POLISH)
3-094-994-22 (FRENCH) 3-094-995-62 (CZECH)
3-094-994-32 (ITALIAN) 3-094-995-72 (HUNGARIAN)
3-094-994-42 (SPANISH) 3-094-995-82 (SLOVAK)
3-094-994-52 (PORTUGUESE) 3-094-995-92 (SWEDISH)
3-094-994-62 (GERMAN) 3-094-996-12 (FINNISH)
3-094-994-72 (DUTCH) 3-094-996-22 (NORWEGIAN)
3-094-994-82 (TRADITIONAL CHINESE) 3-094-996-32 (DANISH)
3-094-994-92 (SIMPLIFIED CHINESE) 3-094-996-42 (THAI)
3-094-995-12 (RUSSIAN) 3-094-996-52 (MALAY)
3-094-995-22 (ARABIC) 3-094-996-62 (TURKISH)
3-094-995-32 (PERSIAN) 3-094-996-72 (GREEK)
DSC-W80/W85_L2
5-15E
DSC-W80/W85
LEVEL 2
US Model
SERVICE MANUAL Canadian Model
AEP Model
Ver. 1.1 2008.05 UK Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Argentine Model
Brazilian Model
SUPPLEMENT-1 Japanese Model
Tourist Model
File this supplement with the service manual.
(DI08-010)
Note: Please refer to Ver. 1.1 of SERVICE MANUAL (9-852-194-31) for the revision of accessories.
• Suffix No. of MC-176 and ST-160 boards have been changed from 11 , 12 into 12 , 22 .
About suffix No. 11 and 12 , 22 , there are no change of schematic diagram and printed wiring board.
2008E0500-1
DSC-W80/W85_L2 © 2008.5
9-852-194-84 Sony EMCS Co. Published by Kohda TEC
5. REPAIR PARTS LIST
5-1. EXPLODED VIEWS
& : Points added portion.
Page Former New
+
11
5 4
4 #65
7 6 #65
7 5 6
9 11
5-2 #65
5 10
))
#65
)5
9*
10
+
#65 #65
Ref. No. Part No. Description Ref. No. Part No. Description
5 3-099-626-01 SHEET, LCD WINDOW ADHESIVE 5 3-099-626-02 SHEET, LCD WINDOW ADHESIVE
9 3-275-132-01 CUSHION (L), LCD
10 3-098-449-02 CUSHION, LCD
11 3-275-133-01 SHEET (L), LCD WINDOW ADHESIVE
DSC-W80/W85_L2
—2—
& : Points added portion.
: Points changed portion.
Page Former New
56 (Note 1) 56 (Note 1, 2)
57 57
ns MIC901 ns MIC901
69 *
54
ns
55 53 54 +
(FFC-093) ns
55 53 62
(FFC-093)
ns
ns
52
5-3 SY
-17 52
3 SY
-17
3
#3
#3
SP901
SP901
51
51
Ref. No. Part No. Description Ref. No. Part No. Description
52 3-099-637-01 LABEL, FUSE 52 3-099-637-03 LABEL, FUSE
56 A-1246-054-A RL-071 BOARD, COMPLETE (Note 1) 56 A-1246-054-A RL-071 BOARD, COMPLETE (Note 1, 2)
56 A-1271-235-A RL-078 BOARD, COMPLETE (Note 1)
* 69 3-269-269-01 SHEET, RL PREVENTION RUST
5-4 0 BT001 1-756-710-11 LITHIUM RECHARGEABLE BATTERY 0 BT001 1-756-711-11 LITHIUM RECHARGEABLE BATTERY
0印の部品,または0印付の点線で囲まれた部品は,
安全性を維持するために,重要な部品です。
従って交換時は,必ず指定の部品を使用してください。
DSC-W80/W85_L2
—3—
5-2. ELECTRICAL PARTS LIST
Page Former New
Ref. No. Part No. Description Ref. No. Part No. Description
A-1246-054-A RL-071 BOARD, COMPLETE A-1246-054-A RL-071 BOARD, COMPLETE
A-1271-235-A RL-078 BOARD, COMPLETE ***********************
*********************** The RL-071 flexible board is compatible with
the RL-078 flexible board.
When replace the RL-078 flexible board, change it to
5-7 the RL-071 flexible board.
S102 1-786-885-42 SWITCH, TACTILE (POWER) S102 1-771-844-21 SWITCH, TACTILE (POWER)
5-7 0 BT001 1-756-710-11 LITHIUM RECHARGEABLE BATTERY 0 BT001 1-756-711-11 LITHIUM RECHARGEABLE BATTERY
S001 1-786-885-42 SWITCH, TACTILE (V (SELF-TIMER)) S001 1-771-844-21 SWITCH, TACTILE (V (SELF-TIMER))
S002 1-786-885-42 SWITCH, TACTILE (W (ZOOM)) S002 1-771-844-21 SWITCH, TACTILE (W (ZOOM))
S003 1-786-885-42 SWITCH, TACTILE (N) S003 1-771-844-21 SWITCH, TACTILE (N)
S004 1-786-885-42 SWITCH, TACTILE (B (FLASH)) S004 1-771-844-21 SWITCH, TACTILE (B (FLASH))
S005 1-786-885-42 SWITCH, TACTILE (T (ZOOM)) S005 1-771-844-21 SWITCH, TACTILE (T (ZOOM))
S006 1-786-885-42 SWITCH, TACTILE (v (DISP)) S006 1-771-844-21 SWITCH, TACTILE (v (DISP))
S007 1-786-885-42 SWITCH, TACTILE (MENU) S007 1-771-844-21 SWITCH, TACTILE (MENU)
S008 1-786-885-42 SWITCH, TACTILE (b (MACRO)) S008 1-771-844-21 SWITCH, TACTILE (b (MACRO))
5-8 S009 1-786-885-42 SWITCH, TACTILE (HOME) S009 1-771-844-21 SWITCH, TACTILE (HOME)
S010 1-786-885-42 SWITCH, TACTILE (z (SET)) S010 1-771-844-21 SWITCH, TACTILE (z (SET))
0印の部品,または0印付の点線で囲まれた部品は,
安全性を維持するために,重要な部品です。
従って交換時は,必ず指定の部品を使用してください。
DSC-W80/W85_L2
—4—
HARDWARE LIST (1/4)
#1: M1.7 X 2.5 #2: M1.7 X 4.0 #3: M1.7 X 2.5 #4: M1.4 X 2.5 (Tapping)
(Black) (Black) (Red) (Dark Silver)
2-635-562-11 2-635-562-31 2-660-401-01 3-348-998-81
#5: M1.7 X 3.5 (Tapping) #6: M1.4 X 1.7 #7: M1.7 X 1.6 #8: M1.7 X 3.5 (Tapping)
(Black) (Silver) (Black) (Silver)
3-080-204-01 2-598-474-01 7-627-552-18 3-078-890-01
#9: M1.7 X 5.0 (Tapping) #10: M1.7 X 4.0 #11: M1.7 X 4.0 (Tapping) #12: M1.7 X 5.0 (Tapping)
(Silver) (Silver) (Silver) (Black)
3-078-890-21 2-599-475-31 3-078-890-11 3-080-204-21
#13: M1.7 X 2.5 (Tapping) #14: M1.7 X 2.5 #15: M1.4 X 1.5 #16: M1.4 X 2.5
(Silver) (Silver) (Silver) (Silver)
3-085-397-01 2-599-475-11 3-062-214-01 2-586-337-01
#17: M1.7 X 1.5 #18: M1.4 X 2.5 #19: M1.2 X 4.0 (Tapping) #20: M1.4 X 3.0
(Silver) (Silver) (Red) (Silver)
2-586-389-01 2-635-591-21 3-086-156-21 2-635-591-31
1.5
2.5 4.0 3.0
3.5
HARDWARE LIST (2/4)
#21: M1.4 X 3.0 #22: M1.7 X 5.0 (Tapping) #23: M1.7 X 4.0 (Tapping) #24: B1.7 X 5.5 (Tapping)
(Black) (Silver) (Black) (Black)
2-662-396-21 3-083-261-01 3-080-204-11 4-679-805-11
#25: M1.7 X 3.0 #26: M1.4 X 2.0 #27: M1.4 X 2.0 #28: M1.4 X 4.0 (Tapping)
(Black) (Silver) (Black) (Dark Silver)
2-635-562-21 2-635-591-11 2-662-396-11 3-348-998-61
#29: M1.4 X 2.5 #30: M1.2 X 3.5 (Tapping) #31: M3.0 X 4.0 #32: M2.0 X 4.5 (Tapping)
(Black) (White) (Silver) (Silver)
2-662-396-01 3-086-156-11 2-102-434-01 2-102-498-01
#33: M3.0 X 6.0 #34: M3.0 X 8.0 #35: M4.0 X 6.0 (Tapping) #36: M3.0 X 6.0
(Silver) (Black) (Silver) (Silver)
3-077-331-21 3-077-331-41 3-975-291-02 4-886-821-11
#37: M2.0 X 6.0 (Tapping) #38: M3.0 X 20.0 (Tapping) #39: M2.6 X 5.0 (Tapping) #40: M2.0 X 4.0 (Tapping)
(Black) (Silver) (Black) (Silver)
3-080-206-31 7-685-651-79 7-685-791-09 7-685-851-04
3.0
20.0
6.0 5.0 4.0
HARDWARE LIST (3/4)
#41: M3.0 X 8.0 (Tapping) #42: M2.0 X 4.0 (Tapping) #43: M1.7 X 4.0 #44: M1.7 X 3.0 (Tapping)
(Silver) (Silver) (Red) (Silver)
3-065-748-01 7-628-253-00 2-660-401-31 3-078-890-61
#45: M1.4 X 2.5 #46: M1.7 X 3.0 #47: M1.4 X 3.0 (Tapping) #48: M1.7 X 2.5
(Silver) (Red) (Silver) (Silver)
2-587-151-01 2-660-401-11 2-665-774-01 3-973-497-91
#49: M2.0 X 4.0 #50: M2.0 X 3.0 #51: M2.0 X 2.5 #52: M2.0 X 4.0 (Tapping)
(Black) (Red) (Silver) (Black)
2-630-005-31 2-891-494-11 3-073-686-01 3-080-206-11
#53: M2.0 X 5.0 (Tapping) #54: M1.75 X 6.0 (Tapping) #55: M2.0 X 4.0 #56: M2.0 X 3.5
(Black) (Black) (Silver) (Silver)
3-080-206-21 3-318-203-11 2-655-582-11 3-067-187-11
#57: M1.7 X 4.0 #58: M2.0 X 6.0 (Tapping) #59: M2.0 X 5.0 (Tapping) #60: M2.6 X 5.0
(Black) (Silver) (Silver) (Black)
7-627-852-18 3-719-408-11 3-080-205-21 3-061-062-11
#61: M3.0 X 10.0 #62: M2.0 X 3.0 #63: M5.0 X 12.5 #64: M1.7 X 5.0 (Tapping)
(Black) (Silver) (Black) (Silver)
7-682-549-09 3-080-202-21 3-060-811-21 2-666-551-21
10.0 12.5
3.0 5.0
#65: M1.4 X 3.5 #66: M1.4 X 1.4 #67: M1.4 X 2.0 #68: M1.7 X 4.0
(Silver) (Silver) (Silver) (Silver)
2-635-591-01 2-635-591-41 3-389-523-16 2-655-581-01
3.0 5.0
2.0
[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)]
Toolbar
Finding a text
1. Click the Find button . Moving with link
2. Enter a character string to be found into a text box, and click
the [Find]. (Specify the find options as necessary) 1. Select either palm tool , zoom tool , text selection tool
, or graphic selection tool .
Application to the Service Manual: 2. Place the pointer in the position in a text where the link exists
To execute “find” from current page toward the previous pages, (such as a button on cover and the table of contents page, or
select the check box “Find Backward” and then click the blue characters on the removal flowchart page or drawing
“Find”. page), and the pointer will change to the forefinger form .
3. Then, click the link. (You will go to the link destination.)
Switching a page
• To move to the first page, click the .
• To move to the last page, click the . “Rotate”
• To move to the previous page, click the . • Click rotate tool , and the page then rotates 90 degrees each.
Revision History
S.M. Rev.
Ver. Date History Contents
issued
1.0 2007.03 Official Release — —
1.1 2008.05 Supplement-1 • Change of Board’s Suffix No. Yes
(S1 DI08-010) • Change of Repair Parts
• Correction of Self-diagnosis Code Table
• Revision of Accessories
S.M. revised: Page 1-6, Page 5-14, Page 5-15
DSC-W80/W85_L2