Professional Documents
Culture Documents
S Passive control
S Area ratio 2 : 1
S Valve spool with 2 mm or 4 mm nose and notch
S High flow rates with low ∆p
S Seat-valve shut-off from A → B and B → A
S Various opening pressures
S With integral orifice for pilot port
S All external parts zinc plated, chromited (CrVI-free)
S Can be fitted in a line-mounting body
1 Description
Series WL22SDLN..., WL22SDRN..., and WL22SDPN pressures in A and B. The area ratio AZ : AA = 2 : 1 results
passively controlled 2/2 logic valves are size 10, high per- in a net force on the valve spool, thus closing the A → B con-
formance screw-in cartridges with an M27 x 2 mounting nection. If the same pressure exists at the A and B ports,
thread. The conical-seat design ensures that the cartridges closing port Z will still cause the valve spool to close, but only
are leak-tight from A → B and from B → A. When the same due to the ≥ 2 bar spring. The valve’s opening and closing
pressure exists at ports A, B and Z, the valve spool is held switching times can be influenced by using suitable orifices
in its closed position by the ≥ 2 bar compression spring. The pairings (in the valve spool and in port Z) and spool nose
A → B and B → A connection is opened or closed by reliev- length (2 mm or 4 mm). 2/2 logic cartridge valves can be
ing or closing the pilot port Z. When the Z port is vented (A used in both mobile and industrial applications. All external
→ B and B → A connection open), there is a continuous dis- parts are zinc plated and chromited (CrVI-free) and are thus
charge of pilot oil through the spool orifice, the flow rate suitable for use in the harshest operating environments. If
being dependent on the ∆p in A, B and Z. When port Z is you intend to manufacture your own cavities or are design-
closed, the check valves that are incorporated in the valve ing a line-mounting installation, please refer to the section
spool allows the pressure in Z to rise to the higher of the two ”Related data sheets”.
2 Symbol
Z Z
B B
A A
3 Technical data
Reference: 400-P-140121-E-00/01.07
Classification: 430.300.-.305.320.335 1/7
General characteristics Description, value, unit
Ambient temperature range -25 °C … +80 °C
Flow direction A → B / B → A, see symbol
4 Performance graphs
measured with oil viscosity 33 mm2/s (cSt)
∆p = f (Q) Pressure drop - Flow rate characteristic ∆p = f (Q) Pressure drop - Flow rate characteristic
- WL22SDLN… (no spool nose) - WL22SDPN... (with spool nose, 4 mm notch)
- WL22SDRN… (with spool nose, 2 mm notch)
P0015.ai
20
20
P0014.ai 2
15
15 2
10 1
10
1
5
5
0
0 0 25 50 75 100 125 150 Q [l/min]
0 25 50 75 100 125 150 Q [l/min]
Attention
The ∆p characteristic is valid when the load pres-
sure in the A → B / B → A connection is higher than
the opening pressure. If the load pressure is lower
than the opening pressure, the load pressure
must first rise to overcome the opening pressure
before flow can occur.
400-P-140121-E-00/01.07 2/7
Series WL22SDLN…, WL22SDRN…, WL22SDPN…
5 Dimensions, sectional view
Model with no nose on the valve spool (WL22SDLN…) Model with nose and notch on the valve spool
- 2 mm nose (WL22SDRN…)
Typenbezeichnung - 4 mm nose (WL22SDPN…)
Model code
30 Typenbezeichnung
8 Model code
Ma = 80 ± 4 [Nm]
Ma = 60 ± 3 [Nm] 30
8
Ma = 80 ± 4 [Nm]
Ma = 60 ± 3 [Nm]
16
Ø 34 4 4
16
1
M27 x 2 Ø 34 1
I1
Z I2
2 M27 x 2
73
57
Z 2
5
73
I3
57
B
I6 5
3 I4
B
2
3
6
A
6
A
AZ = 100 %
AZ = 100 %
AB = 50 %
AB = 50 %
A A = 50 %
A A = 50 %
Z Area AZ : Area AA = 2 : 1
Area AZ : Area AB = 2 : 1
AZ Area AA : Area AB = 1 : 1
B
AB
AA
400-P-140121-E-00/01.07 3/7
Series WL22SDLN…, WL22SDRN…, WL22SDPN…
7 Adjuster types (optional)
Type ”E” adjuster (WL22S...E2D...) ”E” adjuster with ”P” tamper-proof cap (WL22S...P2D…)
Important Important
Can be used to limit the opening stroke, for exam- Valve settings can be sealed by fitting the tamper-
ple, or to block the valve spool in the closed posi- proof cap. To fit the cap, the snap ring 2) has to be
tion. removed. Subsequent adjustment is only poss-
ible by destroying the tamper-proof cap.
5
2)
9,5
16
58,5
52
24
Ma = 60 ± 3 [Nm]
8 Installation information
Important Seal kit no. DS-296-N
No adjustments are necessary, since the cartrid-
Pos. Pcs. Description
ges are set in the factory.
1 1 O-ring No. 119 ∅ 23.47 x 2.62 N90
Attention
2 1 O-ring No. 116 ∅ 18.72 x 2.62 N90
Only qualified personnel with mechanical skills
may carry out any maintenance work. Generally, 3 1 O-ring No. 114 ∅ 15.54 x 2.62 N90
the only work that should ever be needed is to 4 1 O-ring No. 016 ∅ 15.60 x 1.78 N90
check and possibly replace the seals. When
5 2 Backup ring ∅ 17.1 x 2.0 x 1.4 FI0751
changing seals, oil or grease the new seals thor-
oughly before fitting them. 6 2 Backup ring ∅ 15.3 x 2.0 x 1.4 FI0751
400-P-140121-E-00/01.07 4/7
Series WL22SDLN…, WL22SDRN…, WL22SDPN…
9 Application examples
Simplified symbol Simplified symbols
A B B B
P T TL A TL A
Application with 4/3 spool valve Application with 2/2 seat valve
A B
V4
V3
V1 Z
Z V1 Z
Ø 0,8
Ø 0,8 Ø 0,8
B B B
A A A
V1 V1
Z Z
V2
Ø 0,8 Ø 0,8 Application with 2/2 spool valve
B B V5
A A P A
V3
Z
T B
Ø 0,8
P T
B
A
Passively controlled
In the open condition (flow A → B / B → A), there is a continuous flow of pilot oil.
400-P-140121-E-00/01.07 5/7
Series WL22SDLN…, WL22SDRN…, WL22SDPN…
10 Ordering code
Ex. WL22 SD L _ 1 _ 2 D1 3 B -- 10 _ -- _
400-P-140121-E-00/01.07 6/7
Series WL22SDLN…, WL22SDRN…, WL22SDPN…
11 Related data sheets
Reference no. (Old no.) Description
400-P-040011 (i-32) The form-tool hire programme
400-P-060181 (i-45.11) Cavity type DJ
400-P-740131 (G-24.31) Line-mounting body, type GADJA (G 3/4”)
info.ch@bucherhydraulics.com www.bucherhydraulics.com
E 2007 by Bucher Hydraulics AG, CH-3714 Frutigen.
All rights reserved.
Data is provided for the purpose of product description only, and must not be considered as warranted characteristics in the legal sense.
The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to
continual improvement, we reserve the right to amend the product specifications contained in this catalogue.
400-P-140121-E-00/01.07 7/7
Series WL22SDLN…, WL22SDRN…, WL22SDPN…