Professional Documents
Culture Documents
R L
BASS
BOOST
50Hz/10KHz 0dB/+12dB
5) BASS BOOST: Reinforces the level of bass at low frequencies 25Hz to 110Hz. From 0 to +12 dB OBS: 750Wrms per coil.
centered at 45Hz. 1K5 H (1W
) - 2 (* 2 Ohms) x 800Wrms
1K5 H (2W
) - 2 (* 4 Ohms) x 800Wrms
6) VENTILATION OUTPUT: allows the output of heated air from the amplifier.
7) SPEAKERS OUTPUT: This output is MONO. Beware of the polarity of the connections with the speakers INSTALATION WITH 2 WOOFERS AND 2 DRIVERS
and check the minimum impedance allowed in this output. Use cables of at least 8 mm2.
8) COOLER: Cools the internal components of the amplifier. The air enter in the cooler and exits through
the exhaust ventilation (item 6).
9) + BATT: Connect the terminal (+ BATT) to the positive pole of the battery (+12 V) with a cable of at
least 21.0 mm². It is extremely important that you use a fuse or circuit breaker to protect this cable to a
maximum distance of 30 cm from the battery.
10) REM - DRIVE REMOTE: Connect the REM terminal to output for remote / antenna electric of CD/MP3-
Player. So when you turn on your CD/MP3-Player, the amplifier automatically turns on. A cable of 0.5 TABLE SPEAKERS
mm² is sufficient. DRIVER WOOFER
1K5 H 1ohm 60Wrms/8ohms 1K5 H 1 ohm 800Wrms/2ohms
11) GND - GROUND CONNECTION: Use cable with 21.0 mm². Plug the cable into the chassis of the 1K5 H 2ohms 100Wrms/8ohms 1K5 H 2 ohms 800Wrms/4ohms
vehicle.
AMPLIFIER IS FOR A SUBWOOFER, WOOFER, DRIVER
NOTE: Always connect the cable GND (-) of CD-Player, or other devices at the same point.
AND ALL SPEAKER THAT RESPONSE UNTIL 10KHZ.
LEDS INDICATORS (TOP OF THE AMPLIFIER)
- BLUE LED (POWER) - RED LED (PROT) illuminates only when - RED LED (CLIP) flashes when
lights when the power there is a problem in the functioning of the amplifier output begin to
is on. the device. distort the sound.
SYSTEM TROUBLESHOOTING
If some problem occurs, the amplifier will shut down and the RED LED will flash alternately with the BLUE LED. As
the problem occurred, the BLUE LED will blink a certain number of times. So we have a diagnosis according to the
table below:
DIGITAL LINE
USER’S GUIDE
Note: If only the RED LED blinks (BLUE LED OFF), turn on the device with the volume of CD/MP3-player down. If
the problem persists, please contact us.
WHAT TO DO IN CASE OF PROBLEMS
NOT TURN ON:
- The cables are not properly connected (terminals +BATT, GND and REM). Make sure that all
connections are mechanical and electrical contact.
- Fuses / breakers (external) are defective or burned. Pay attention to the correct value of the new fuse!
NO SOUND:
HALF
- The cables of the speakers or RCA plugs are not connected correctly.
- Check that the LEVEL control is not in the minimum.
BRIDGE
NO SOUND/PROTECTION RED LED FLASHING:
- See diagnosis UP (SYSTEM TROUBLESHOOTING). SPECIFICATIONS
- The speakers or cables defectives thus check the speakers, cables and connections.
POOR SOUND QUALITY (DISTORTION): MODEL: 1K5 H – 1 OHM 1K5 H – 2 OHMs 1K H – 1 OHM 1KH – 2 OHMs
Channels: 1 1 1 1
- The speakers are overloaded, therefore decrease the level and redo the gain setting (See item 2 / Power @ 13.8V Mono 1 Ohm: 1830 Watts RMS - 1360 Watts RMS -
OVERVIEW). Power @ 13.8V Mono 2 Ohms: 1090 Watts RMS 1710 Watts RMS 820 Watts RMS 1230 Watts RMS
WEAK BASS: Power @ 13.8V Mono 4 Ohms: 600 Watts RMS 960 Watts RMS 440 Watts RMS 686 Watts RMS
- Cables speakers (+) and (-) are reversed, speaker out of phase (see Section 7 / overview). Power @ 12.6V Mono 1 Ohm: 1500 Watts RMS - 1156 Watts RMS -
MOTOR NOISE, HORN, SIGNAL LIGHT, ETC: Power @ 12.6V Mono 2 Ohms: 930 Watts RMS 1500 Watts RMS 666 Watts RMS 1012 Watts RMS
Power @ 12.6V Mono 4 Ohms: 490 Watts RMS 810 Watts RMS 362 Watts RMS 542 Watts RMS
- Use suppressive cables in ignition candles. Minimum Work Impedance: 1 Ohm 2 Ohms 1 Ohm 2 Ohms
- Use capacitors in the alternator, horn and ignition. Minimum Input Sensitivity: 0,2V 0,2V 0,2V 0,2V
- Pass the RCA cable away from any other cable, because it is more sensitive to interference. Total Harmonic Distortion: < 0,9 % THD < 0,9 % THD < 0,9 % THD < 0,9 % THD
- Connect to power (+12 V) to separate the sound system. Use a fuse to 30 cm from the battery for Signal to Noise: > 90 dB > 90 dB > 90 dB > 90 dB
Crossover LOW PASS: 50 Hz to 10 KHz 50 Hz to 10 KHz 50Hz to 10 KHz 50 Hz to 10 KHz
protection. Freq. Response (-3dB) @ 8 Ohms: 20 Hz to 10 KHz 20 Hz to 10 KHz 20 Hz to 10 KHz 20 Hz to 10 KHz
- Make a good grounding of the amplifier. To do this removes the paint from the chassis of the vehicle at Bass Boost: 0 to +12dB @ 45Hz 0 to +12dB @ 45Hz 0 to +12dB @ 45Hz 0 to +12dB @ 45Hz
the desired point. Screw the cable using a ground terminal. To protect from oxidation, insulate with Subsonic Filter: 20 Hz to 80Hz 20 Hz to 80Hz 20 Hz to 80Hz 20 Hz to 80Hz
paint. Power Tension: 9 to 15V 9 to 15V 9 to 15V 9 to 15V
- Do not loop the ground wire. Avoid using several ground wires. Prefer a star connection, with all the Consumption Music Signal (12,6 V): 72 A 72 A 55 A 45A
ground wires aside from a single point. Consumption BASS Signal (12,6 V): 144 A 144 A 111 A 89 A
Dimentions mm (A x L x C): 70 x 280 x 170 70 x 280 x 170 70 x 280 x 170 70 x 280 x 170
Weight: 2,2 Kg. 2,2 Kg. 2,2 Kg. 2,2 Kg.
www.stetsom.com.br - export@stetsom.com MAR/10