You are on page 1of 26

1 Top of Form

A routing issue has occurred in your internetwork. Which of the following type of devices should be exam
to isolate this error?
access point

host

hub

router

switch
Bottom of Form

2 Top of Form
Which password would allow a user to establish a Telnet session with a Cisco device?
VTY password

enable password

console password

enable secret password


Bottom of Form

3 Top of Form
An administrator makes changes to the default configuration of a router and saves them to NVRAM. Afte
testing, it is discovered that the configurations did not have the desired effect and must be removed. Wha
must be taken to remove the changes and return the router to the default configuration?
Reboot the router.

Use no version of the commands that are issued.

Issue the erase startup-config command, and then reboot the router.

Issue the erase running-config command, and then reboot the router.
Bottom of Form

4 Top of Form
What are three characteristics of CSMA/CD? (Choose three.)
Devices can be configured with a higher transmission priority.

A jam signal indicates that the collision has cleared and the media is not busy.

A device listens and waits until the media is not busy before transmitting.
The device with the electronic token is the only one that can transmit after a collision.

All of the devices on a segment see data that passes on the network medium.

After detecting a collision, hosts can attempt to resume transmission after a random time delay has ex
Bottom of Form

5 Top of Form
What is the Cisco IOS?
system software for Cisco devices

Read Only Memory in Cisco devices

non-volatile storage for device configurations

an initial operating system that is used for boot functions


Bottom of Form

6 Top of Form
A network administrator is asked to design a new addressing scheme for a corporate network. There are 6
in the main office, 40 users in the branch office, 28 users in manufacturing, 12 in the sales office, and 4 u
the research office. Which VLSM addressing scheme that uses the 192.168.88.0/24 network will fulfill th
requirements while wasting the fewest addresses?
192.168.88.0/26 main
192.168.88.32/26 branch
192.168.88.64/26 manufacturing
192.168.88.96/27 sales
192.168.88.128/28 research
192.168.88.0/26 main
192.168.88.64/26 branch
192.168.88.128/27 manufacturing
192.168.88.160/28 sales
192.168.88.176/29 research
192.168.88.0/27 main
192.168.88.32/27 branch
192.168.88.64/28 manufacturing
192.168.88.80/29 sales
192.168.88.88/30 research
192.168.88.0/27 main
192.168.88.64/28 branch
192.168.88.80/28 manufacturing
192.168.88.96/29 sales
192.168.88.104/30 research
Bottom of Form

7 Top of Form
Refer to the exhibit. Which two layers of the OSI model describe the same functions as the transport and
layers of the TCP/IP model? (Choose two.)
application layer

presentation layer

session layer

transport layer

network layer

data link layer

physical layer
Bottom of Form

8 Top of Form
Which requirement would cause a network designer to use a router instead of a switch in a network desig
creating smaller collision domains

providing both UTP and fiber ports

connecting end-user devices to the network core

interconnecting several networks using different technologies


Bottom of Form

9 Top of Form
Which identifier is contained in the header of the Layer 2 Ethernet frame?
timing and synchronization of bits
source and destination port numbers

logical source and destination addresses

physical source and destination addresses


Bottom of Form

10 Top of Form

Refer to the exhibit. The router of the company failed and was replaced. After the replacement, hosts C an
the Education office are able to ping each other, but they are unable to access the hosts in the Accounts off
What is the likely cause of the problem?
The IP address at the fa0/0 interface of the router is incorrectly configured.

The subnet mask at the fa0/1 interface of the router is incorrectly entered.

The IP address at the serial interface of the router is incorrectly configured.

The hosts in the Accounts office are not on the same subnet as the hosts in the Education office.
Bottom of Form

11 Top of Form
Refer to the exhibit. Which two facts can be determined about the topology? (Choose two.)
Three networks are needed.

Two logical address ranges are required.

Three broadcast domains are present.

Three collision domains are present.

Four networks are needed.


Bottom of Form

12 Top of Form
Which option shows how a router will route packets to a remote network?
Bottom of Form

13 Top of Form

Refer to the exhibit. From global configuration mode, an administrator is attempting to create a message-
day banner by using the command banner motd V Authorized access only! Violators will be prosecut
When users log in using Telnet, the banner does not appear correctly. What is the problem?
The banner message is too long.

The delimiting character appears in the banner message.

The symbol “!” signals the end of a banner message.

Message-of-the-day banners will only appear when a user logs in through the console port.
Bottom of Form

14 Top of Form
Which two statements are true of private IP addresses? (Choose two.)
They cannot be routed.

They are defined by RFC 790.

They can only be assigned to hosts.

They will not be forwarded by Internet routers.

They are in the reserved range of 224.0.0.0 to 239.255.255.255.


They must be translated to public addresses to access the Internet.
Bottom of Form

15 Top of Form

Refer to the exhibit. Which list refers only to end devices?


D,E,F,G

A,H,B,C

A,D,E,F

A,D,E,G
Bottom of Form
16 Top of Form

Refer to the exhibit. Host A wants to connect to host B on a different network. Which three IP addresses c
assigned to host A to enable this connectivity? (Choose three.)
172.16.11.36
172.16.11.95

172.16.11.88

172.16.11.70

172.16.11.64

172.16.11.67
Bottom of Form

17 Top of Form
A network administrator subnets the network 192.168.1.0/24 into four subnets. Which option correctly ad
Router1 and host A into the second subnet created?

Bottom of Form

18 Top of Form
Which TCP/IP model layer creates additional overhead on network resources due to acknowledgments, tr
and retransmission of data?
internet

transport

application

network access
Bottom of Form

19 Top of Form
Which prompt is associated with the privileged exec mode?
R1>

R1#

R1(config)#

R1(config-router)#
Bottom of Form

20 Top of Form
A network has grown too large for technicians to configure network addresses and hosts files for name
resolution. Which two application layer services should be added to the server to allow these needs to be
satisfied dynamically? (Choose two.)
DNS

FTP

DHCP

HTTP

SMTP
Bottom of Form

21 Top of Form
Refer to the exhibit. Assume all devices are using default configurations. How many subnets are required
address the topology that is shown?
1

7
Bottom of Form

22 Top of Form
What can the user do from the command prompt, Router(config-line)# ?
Configure one of the network interfaces.

Configure one of the physical or virtual lines.

Verify the running configuration on the device.

Configure the parameters for one of the routing protocols.


Bottom of Form

23 Top of Form
Which protocol is a client/server file sharing protocol and also a request/response protocol?
FTP

SMB

TCP

UDP
Bottom of Form
24 Top of Form
Which answer lists the CLI mode hierarchy from least level of privilege to greatest?
global, privileged, user, specific

global, user, privileged, specific

user, global, privileged, specific

user, privileged, global, specific


Bottom of Form

25 Top of Form

Refer to the exhibit. An employee wants to access the organization intranet from home. Which intermedia
device should be used to connect the organization intranet to the Internet to enable this access?
hub

switch

router

wireless access point


Bottom of Form

26 Top of Form
Which password is automatically encrypted when it is created?
vty

aux
console

enable secret

enable password
Bottom of Form

27 Top of Form

Refer to the exhibit. Which type of network design is shown?


client/server

wide area

dedicated server

peer-to-peer
Bottom of Form

28 Top of Form
Refer to the exhibit. Which logical topology describes the exhibited network?
star

ring

point-to-point

multi-access
Bottom of Form

29 Top of Form

Refer to the exhibit. A host is connected to hub 1. Which combination of IP address, subnet mask, and de
gateway can allow this host to function in the network?
IP address: 172.16.31.36 Subnet mask: 255.255.255.240 Default gateway: 172.16.31.35

IP address: 172.16.31.63 Subnet mask: 255.255.255.224 Default gateway: 172.16.31.35

IP address: 172.16.31.29 Subnet mask: 255.255.255.248 Default gateway: 172.16.31.35

IP address: 172.16.31.32 Subnet mask: 255.255.255.224 Default gateway: 172.16.31.35

IP address: 172.16.31.29 Subnet mask: 255.255.255.240 Default gateway: 172.16.30.1

IP address: 172.16.31.37 Subnet mask: 255.255.255.224 Default gateway: 172.16.31.35


Bottom of Form

30 Top of Form
Which physical component is used to access and perform the initial configuration on a new unconfigured
Bottom of Form

Top of Form

3 Top of Form

1
Refer to the exhibit. The diagram represents the process of sending e-mail between clients. Which list correctly
identifies the component or protocol used at each numbered stage of the diagram?
1.MUA 2.MDA 3.MTA 4.SMTP 5.MTA 6.POP 7.MDA 8.MUA

1.MUA 2.POP 3.MDA 4.SMTP 5.MTA 6.MDA 7.SMTP 8.MUA

1.MUA 2.POP 3.SMTP 4.MDA 5.MTA 6.SMTP 7.POP 8.MUA

1.MUA 2.SMTP 3.MTA 4.SMTP 5.MTA 6.MDA 7.POP 8.MUA


Bottom of Form

3 Top of Form

f
Athens

Ankara

London

Paris
PC4
Bottom of Form

33 Top of Form

Refer to the exhibit. Each media link is labeled. What type of cable should be used to connect the differen
devices?
Connection 1 - rollover cable
Connection 2 - straight-through cable
Connection 3 - crossover cable
Connection 1 - crossover cable
Connection 2 - rollover cable
Connection 3 - crossover cable
Connection 1 - straight-through cable
Connection 2 - crossover cable
Connection 3 - crossover cable
Connection 1 - straight-through cable
Connection 2 - crossover cable
Connection 3 - straight-through cable
Connection 1 - crossover cable
Connection 2 - straight-through cable
Connection 3 - crossover cable
Bottom of Form

34 Top of Form
Which application layer protocol allows administrators to log into a server from remote locations and con
server as though logged in locally?
DNS

FTP

DHCP

SMTP

Telnet
Bottom of Form

35 Top of Form
Refer to the exhibit. A technician is working on a network problem that requires verification of the router
interface. What address should be pinged from this host to confirm that the router interface is operational?
127.0.0.1

192.168.64.196

192.168.254.1

192.168.254.9

192.168.254.254
Bottom of Form

36 Top of Form
An administrator is in the middle of entering a lengthy command when suddenly output from the IOS app
stating that an interface has gone down and then up again. Consequently, the command that the administr
was typing is no longer legible on the terminal. What CLI keystrokes can be entered to return to the line t
administrator was typing?
Ctrl-D

Ctrl-K

Ctrl-R

Ctrl-Z
Bottom of Form
37 Top of Form
A technician wishes to connect two computers to move data from one to the other before reloading the op
system. The NICs on both PCs do not support autosensing feature. Which procedure will satisfy the
requirement?
Interconnect the two PCs with a rollover cable.

Interconnect the two PCs with two rollover cables and a hub.

Interconnect the two PCs with a crossover cable.

Interconnest the two PCs with two crossover cables and a hub.
Bottom of Form

38 Top of Form
Which of the following are the address ranges of the private IP addresses? (Choose three.)
10.0.0.0 to 10.255.255.255

200.100.50.0 to 200.100.25.255

150.150.0.0 to 150.150.255.255

172.16.0.0 to 172.31.255.255

192.168.0.0 to 192.168.255.255

127.16.0.0 to 127.31.255.255
Bottom of Form

39 Top of Form
Refer to the exhibit. Host A is able to access resources on the local LAN but is unable to access any resour
the Internet. What is the likely cause of this problem?
The host subnet mask in incorrect.

The network uses private addresses.

The host address is a network address.

The default gateway is on a different subnet from the host.


Bottom of Form

40 Top of Form
Which OSI layer offers ordered data reconstruction services?
application layer

network layer

presentation layer

session layer

transport layer
Bottom of Form

41 Top of Form
Refer to the exhibit. An administrator made several changes to the configuration of the router but did not
accomplish the desired result. To undo the changes the reload command was used. What will happen if th
administrator answers yes to the prompt?
The changes will be lost and the configuration file in RAM will be loaded.

The changes will be saved and the configuration file in RAM will be loaded.

The changes will be lost and the configuration file in NVRAM will be loaded.

The changes will be saved and the configuration file in NVRAM will be loaded.
Bottom of Form

42 Top of Form

Refer to the exhibit. A network administrator is troubleshooting a link that is down between Router1 and
Router2. To correct the problem, which wire pairs need to be switched on one of the Ethernet cable ends?
pair 1 and pair 2

pair 1 and pair 3

pair 2 and pair 3

pair 2 and pair 4


Bottom of Form

43 Top of Form
Refer to the exhibit. A network technician has made several changes to R1 since the configuration has las
saved. The modified configuration did not produce the desired changes. The technician wants to store a b
copy of the saved configuration on a TFTP server before reloading. Which action will cause the unmodifi
to be saved on the TFTP server?

Bottom of Form

44 Top of Form
Which location of router memory is cleared with the erase startup-config command?
flash

RAM

ROM

NVRAM
Bottom of Form

45 Top of Form
A network technician has made a UTP cable that is terminated as T568A on one end and T568B on the op
end. What type of cable has been constructed?
patch

console

crossover

straight-through
Bottom of Form

Top of Form

4 Top of Form

Refer to the exhibit. Host A is accessing multiple servers. Which combination of port number and address will
uniquely identify a particular process running on a specific server?
MAC address of the server and port number of the service
IP address of the host and port number of the service

MAC address of the host and port number of the service

IP address of the server and port number of the service


Bottom of Form

4 Top of Form

Refer to the exhibit. Host A sends a frame with the destination MAC address as FFFF.FFFF.FFFF. What action
will the switch take for this frame?
It will drop the frame.

It will send the frame back to host A.

It will send the frame to all hosts except host A.

It will forward the frame to the default gateway.


Bottom of Form

48 Top of Form
Which two types of media can provide bandwidth up to 1 Gb/s? (Choose two.)
10 BASE-T

100 BASE-T

100 BASE-FX
1000 BASE-TX

1000 BASE-SX
Bottom of Form

49 Top of Form
Which physical connector type is used for a serial V.35 connection to the CSU/DSU?

Bottom of Form

50 Top of Form
How can ARP be used to help document the network?
It can list each hop on the way to a destination host.
It can show the average latency of hosts on the network.

It can provide a list of physical addresses on the network.

It can indicate which hosts are not responding to network traffic.


Bottom of Form

51 Top of Form
What happens when a host station receives a frame that contains its own MAC address in the destination
The Layer 2 information is removed and the frame is pushed up to Layer 3.

The host station will copy the information to its buffers and send it back out.

The frame originated from the host and will be ignored.

The Layer 3 information is added to the frame.


Bottom of Form

52 Top of Form
Which option correctly identifies the interface or interfaces used to connect the router to a CSU/DSU for
connectivity?
Bottom of Form
Bottom of Form
Bottom of Form

You might also like