You are on page 1of 4

POWER , AKE·OFF

MODEL 8-3311
(Formerly PT-7)

ASSEMBLY CLUTCH OPERATION AND ADJUSTMENT


Mount clutch rod mounting assembly plate and rod, Attaching tools are started and stopped by oper-
Part 7270 to engine face with two hex head bolts, ating the engine mounted clutch. By moving the clutch
Part 908032-4 and lock washer, Part 920083-4 rod from the outside notch in the brocket, to the inside
in the two lower right hand holes of the engine face. notch, (toward the tractor), the friction disc is engaged.
The other end of this rod is fork shaped with a %"
Install the plate adapter, Part 7273, to the hood locknut on each side. By moving these nuts in toward
stand, using the two )4-20 x ~ whizlock bolts. Fasten the tractor, more tension will be applied to the clutch.
the clutch rod bracket to the plate adapter with two Adjust nuts so that clutch just disengages with clutch
K6-18 x % Hex Bolts and Nuts. See exploded view rod in middle notch (above arrow) of bracket, Part
drawing. 4383. Refer to decal on bracket.

Place clutch plate assembly, Part 6655 over engine LUBRICATION


shaft and align the four holes with the holes in the The clutch housing has a needle bearing pressed
engine pulley. Slide the sleeve over the engine inside with a grease seal. This bearing has been
shaft. Place the two retainers in the groove of the greased at the factory. Every 25 hours the clutch
sleeve and secure with the four whizlock bolts, Port housing should be removed and a SMALL amount of
960151-4. good qua,lity multipurpose-type grease applied to
partially fill the spaces between the rollers.
Slide clutch housing, Port 6660 on the sleeve until
it comes in contact with the clutch plate. ENGINE PULLEYS
For all 8 H.P. tractors with standard geared trans-
Install clutch rod assembly, Part 4355 down thru missions and model 1046 use the 2~" dia. pulley,
the opening in the bracket, Part 4383 until the forked Part No. 7363. For all 8 H.P. tractors with the Wheel-
shaped part of the rod is between the two nuts on the A-Matic transmission (Hydro-Static) and model 1075
clutch rod mounting assembly plate, Part 7270. Now use the 3~" dia. pulley, Part No. 7362. Space pulley
insert hairpin cotter, Part 933506-4 thru clutch housing No . 7362 1" away from engine face. Space pulley No.
and plate on clutch rod. 7363 )4" away.
PARTS LIST
When ordering parts always list Part No. and Name of Part.

Ito," Part No. Ite," Part No.


No. No. Description Req'd. No. No. Description Req'd.
1 7270 Ass'y. - Plate and Shoft 1 14 6935 Race - Bearing 1
2 908032·4 Bolt Hex %.16 x % 2 15 6659 Retainer - Bearing Race 2
3 920083·4 lockwasher % Dia . 2 16 960151·4 Bolt - Whixlock Ji.20 x X 6
4 908017·4 Bolt Hex ~6·18 x % 2 17 6660 Housing - Clutch 1
5 915112·6 Nut ~6·18 Nylok 2 18 6662 Bearing 1
6 4355 Ass'y. Clutch Rod 1 19 6663 Seal 1
7 933506·4 Hair Pin 1 20 5196 Ball Bearing 1
8 2709 Knob 1 21 935032 Snap Ring 1% Internal 1
9 4383 Bracket 1 22 936125 Snap Ring % External 1
10 6655 Ass'y. Clutch Plate and Facing 1 23 5197 Shaft - Clutch 1
11 6656 Plate Clutch 1 24 7273 Plate Adaptor 1
12 4365 Facing 1 25 7359 Decal - Clutch Adj. 1
13 6657 Rivet 6 26 915663·4 Nut % ·16 Elastic Stop 2

1·17·67 FORM NO. 320


, PARTS LIST AND INSTRUCTIONS !
POWER TAKE·OFF
MODEL 8-3311
(Formerly PT-7)

WHEELHORSE PRODUCTS, -INC. • SOUTH BEND, clND.

ASSEMBLY CLUTCH OPERATION AND ADJUSTMENT


Mount clutch rod mounting assembly plate and rod, Attaching tools are started and stopped by oper-
Part 7270 to engine face with two hex head bolts, ating the engine mounted clutch. By moving the clutch
Part 908032-4 and lock washer, Part 920083-4 rod from the outside notch in the bracket, to the inside
notch, (toward the tractor), the friction disc is engaged.
in the two lower right hand holes of the engine face.
The other end of this rod is fork shaped with a Ye"
Install the plate adapter, Part 7273, to the hood locknut on each side. By moving these nuts in toward
stand, using the two ~ -20 x ~ whizlock bolts. Fasten the tractor, more tension will be applied to the clutch.
the clutch rod bracket to the plate adapter with two Adjust nuts so that clutch just disengages with clutch
7\6-18 x % Hex Bolts and Nuts. See exploded view rod in middle notch (above arrow) of bracket, Part
drawing . 4383. Refer to decal on bracket.

Place clutch plate assembly, Part 6655 over engine LUBRICATION


shaft and align the four holes with the holes in the The clutch housing has a needle bearing pressed
engine pulley. Slide the sleeve over the engine inside with a grease seal. This bearing has been
shaft. Place the two retainers in the groove of the greased at the factory . Every 25 hours the clutch
sleeve and secure with the four whizlock bolts, Part housing should be removed and a SMALL amount of
960151-4. good quality multipurpose-type grease applied to
partially fill the spaces between the rollers.
Slide clutch housing, Part 6660 on the sleeve until
it comes in contact with the clutch plate. ENGINE PULLEYS
For all 8 H.P . tractors with standard geared trans-
Install clutch rod assembly, Part 4355 down thru missions and model 1046 use the 2~" dia. pulley,
the opening in the bracket, Part 4383 until the forked Part No. 7363. For all 8 H.P. tractors with the Wheel-
shaped part of the rod is between the two nuts on the A-Matic transmission (Hydro-Static) and model 1075
clutch rod mounting assembly plate, Part 7270. Now use the 3~" dia. pulley, Part No. 7362. Space pulley
insert hairpin cotter, Part 933506-4 thru clutch housing No. 7362 1" away from engine face . Space pulley No.
and plate on clutch rod. 7363 }iN away.
PARTS LIST
When ordering parts always list Part No . and Name of Part.

Item Part No. Item Part No.


No. No. Description Req'd. No . No. Description Req'd.

1 7270 Ass' y. - Plate and Shaft 1 14 6935 Race - Bearing 1


2 908032·4 Bolt Hex % .16 x % 2 15 6659 Retainer - Bearing Race 2
3 920083·4 lockwasher % Dia . 2 16 960151·4 Bolt - Wh izlock );,1.20 x );2 6
4 908017·4 Bolt Hex ~6·18 x % 2 17 6660 Housing - Clutch 1
5 915112·6 Nut ~6· 18 Nylok 2 18 6662 Bearing 1
6 4355 Ass'y. Clutch Rod 1 19 6663 Seal 1
7 933506·4 Hair Pin 1 20 5196 Ball Bearing 1
8 2709 Knob 1 21 935032 Snap Ring 1% Internal 1
9 4383 Bracket 1 22 936125 Snap Ring % External 1
10 6655 Ass'y. Clutch Plate and Facing 1 23 5197 Shaft - Clutch 1
11 6656 Plate Clutch 1 24 7273 Plate Adaptor 1
12 4365 Facing 1 25 7359 Decal - Clutch Adj . 1
13 6657 Rivet 6 26 915663 · 4 Nut %. 16 Elastic Stop 2

lITHO IN U. S. A. 7·69 FORM NO . A·5167

You might also like