Professional Documents
Culture Documents
POWER RELAY
1 POLE - 6A Slim Type (Medium Load Control)
FTR-LY Series
n FEATURES
lSlim 15.0mm (h) x 5.0 mm (w) x 28.0mm (l)
l1 form C and right angle type available
Mounting space: 140mm2, weight: 5.0g
l
compliance
Socket type available
l
RoHS compliant
l
n PARTNUMBER INFORMATION
FTR-LY A A 005 Y - SK
[Example] (a) (b) (c) (d) (e) (f )
Actual marking does not carry the type name : "FTR" and "SK"
E.g.: Ordering code: FTR-LYAA005Y-SK Actual marking: LYAA005Y
1
FTR-LY
FTR-K1SERIES
SERIES
n SPECIFICATION
Item LY (C,R) A ( ) (Y,E,V) LY (A,P) A ( ) (Y,E,V)
Contact Configuration 1 form C (SPDT) 1 form A (SPST-NO)
Data Construction Single
Material Y: AgSnO2 / E: AgNi / V: AgSnO2 + Au 0.3μm
Y, E: Max. 100 mOhm at 6 VDC, 1 A
Resistance (initial)
V: Max. 30 mOhm at 6 VDC, 1A
Contact rating 6A, 250VAC / 24VDC
Max. carrying current 6A
Max. switching voltage 250VAC
Max. switching power 1,500VA / 144W
Y, E: 100 mA 5 VDC
Min. switching load *
V: 10mA 5 VDC
Life Mechanical Min. 10 x 106 operations
Min. 50 x 103 operations (N.O.)
Electrical Min. 30 x 103 operations (N.C.) at 6A, 250VAC /
30VDC resistive
Coil Data Rated power 170 to 217 mW
Operate power 74 to 76 mW
Operating temperature range -40 °C to +85 °C (no frost)
Timing Data Operate (at nominal voltage) Max. 8ms (no diode, without bounce)
Release (at nominal voltage) Max. 4ms (no diode, without bounce)
Insulation Resistance (initial) Min. 1,000MOhm at 500VDC
Dielectric strength Open contacts 1,000VAC (50/60Hz) 1min.,10mA detection current
Contacts to coil 4,000VAC (50/60Hz) 1min.,10mA detection current
Surge strength Coil to contacts 6,000V / 1.2 x 50µs standard wave
Clearance 8 mm
Creepage 8 mm
EN61810-1, VDE0435 Voltage 250V
Pollution degree 3
Material group III a
Category C / 250V
Other Misoperation 10 to 55Hz double amplitude 1.0mm
Vibration resistance
Endurance 10 to 55Hz double amplitude 1.5mm
Misoperation Min. 50m/s² (11 ± 1ms) Min. 100m/s² (11 ± 1ms)
Shock
Endurance Min. 1,000m/s² (6 ± 1ms)
Weight Approximately 5 g
Sealing Plastic sealed RTIII
* Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual
load before production since reference values may vary according to switching frequencies, environmental contions
and expected reliability levels.
2
FTR-LY
FTR-K1SERIES
SERIES
n COIL RATING
Note: All values in the table are valid for 20°C and zero contact current.
* Specified operate values are valid for pulse wave voltage.
n SAFETY STANDARDS
Type Compliance Contact rating
UL UL 508 Flammability: UL 94-V0 (plastics)
5A, 277 VAC (resistive)
E63614 5A, 30 VDC (resistive)
CSA C22.2 No. 14 1/10 HP, 277VAC /125VAC
LR 40304 Pilot duty: D300, C300, R300
VDE EN 61810-1 (VDE 0435-Part 250VAC;6A
40006591 201) 2004-07 30VDC;6A
EN 61984 (VDE 0627) 250VAC;6(1,5)
EN 60730-1 (VDE 0631-Part 1) 250VAC;3(1,5)
EN 60335-1 (VDE 0700-Part 1)
SEMKO EN 61058-1:1992+A1 250V, 6(3)A
EN 61095:1993+A1+A11
3
FTR-K1SERIES
FTR-LY SERIES
n CHARACTERISTIC DATA
4
FTR-LY
FTR-K1SERIES
SERIES
n DIMENSIONS
Straight terminal type
5
FTR-LY
FTR-K1SERIES
SERIES
n DIMENSIONS
Socket type
6
FTR-LY
FTR-K1SERIES
SERIES
at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf
l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified.
This material has been verified to be compatible with PbSn assembly process.
3. Moisture Sensitivity
l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated.
4. Tin Whiskers
l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length
whisker was found by our in house test.
7
FTR-K1SERIES
FTR-LY SERIES
©2010 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective
owners.
The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for gen-
eral information purposes.
The use of the contents, data and information provided in this datasheet is at the users’ own risk.
Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehen-
sive, complete and up to date.
Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf
of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information
and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof.
Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility
or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for
particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy,
comprehensiveness, usefulness, availability and completeness thereof. Rev. August 17, 2010