Professional Documents
Culture Documents
I cannot remember the options to many questions but I do remember 116 of them. There were 120
technical questions and 36 questions on English, quantitative aptitude and GK.
Technical:
1. what is used for heat dissipation in ICs
2. for an amplifier, given IC(dc) and IC(ac)(p) for a 1k load calculate avg dc power dissipated.
3. given hfe calculate hfc.
17. dynamic characteristics of capacitive transducers are similar when used as HPF/LPF/…
6. The o?p voltage e1 & e2 of 2 full-bridge inverters added using o/p transformer. In
order to eliminate 5th harmonic from o/p voltage, the phase angle between e1&e2 will
be-
8. An SCR has half cycle surge current rating of 3000A for 50Hz. One cycle surge
current will be. (double of that)
9. When compared to an symmetrical thyristor, the turn off time & reverse blocking
voltage of an asymmetrical thyristor will be-
10. A step-up chopper is feed from an 220v dc source to deliver a load voltage of 66o v.
If the non conducting time is 100micro-sec then reqd pulse width will be. (get duty
cycle only)
11. There were some 5-6 numerical problems which I could not remember totally but
they consist of firing angle & power transfer of inverter, SCR. Go llok for that.
12. Relay current setting & Ct ratio was given you have to find out Relay Pick up
Current.
13. One question from Dc shunt motor- like a resistance is added of 4.5 ohm in series
with arm where rest of arm is 0.5 ohm. Machine is supplied 220v. find out the null
current.
14. In aptitude part see through series completion there was a 5-6 no of that.
19. Good transformer oil contains how much amount of water in ppm?
21. K/s(s+1)(s+5) then find out the value of K so that system become stable.
24. If a square waveform if given to the supply side of a 2wdg transformer its o/p
waveform will be-
26. If a transformer is operating in .8 PF lag & at efficiency of .9, if now P is .8 lead the
efficiency will become.
29. A alternator is connected to a grid. Now its prime mover is go slow by ½. Change in
its exiting current to held in synchronism.
31. The voltage of a generator and an infinite bus are given 0.92, 10 deg & 1.0, 0 deg
resp. the generator acts as a –
32. A wave will not experience any reflection when impedance of line is equal to- surge
imp
38. Read all electrostatic instrument related question from any competitive exam book.
43. A question like an ac is applied against a moving coil meter it will reads-
Test Paper :5
Hai friends,,
Here are the some of the technical questions posed in the HAL exam for the post of
Management/Design Trainee on 26-11-2006 for electrical branch.
4) What is the approximate peak overshoot for a unity feedback system with damping
factor 0.6?
a)10% b)5% c)15% d)20%
6) On no load in EHV lines what is the relation between receinving and sending end
voltage?
ans: receiving end voltage > sending end voltage
9) If both the juctions of transistor are forward biased, in wat region transistor works
ans: saturation region
12) What is the GMD if the distance between the lines are 6m,6m,12m?
ans: 7.058m( approx)
15)There are two to three questions based on Laplace and Inverse Laplace transforms
17)When do two wattmeters show same value of opposite readings in two wattmeter
method
a) 300 lag
b) 600 lag
c) between 600 and 900 lag
d) zpf lag
ans: d
19) What is the value of resistance when both length and diameter of the wire are
doubled?
ans: halved
22) What happens to the value of inductance when self GMD is doubled?
26) What is the easier method for finding no. of poles in the right half of s-plane?
a) Niquist plot
b) R-H criterion
c) Root-Locus method
d) Polor plot
ans: b
27) How many no of poles located in the right half of s-plane for the characteristic
equation...
c) Ampere Hours
d) Joules
29)What is the gate used to get high output when all the inputs are low?
a) NOR
b) NAND
c) Ex-OR
d) Ex-NOR
ans: b
31) What is the line current of a circuit when the current transformer of 1000:5 rating
measures 4Amperes?
ans: 800A
32) If the time delay of relay with TMS setting 0.1 is 10 sec, then what is the time
delaty when the TMS setting is changed to 0.5
38) In the following locations where is hydal power plant is not located?
ans: i dont remember the places
45) What are the avg and rms values of full wave rectifier
ans: 2Vm/pie, Vm/21/2
Regards,
Prashanth Tirungari
There were 36 questions in this section, about 12 questions each in verbal,quant and GK. some of the GK
questions were:
Hallo friends
We are from mechanical stream ..and followeing paper will help you for oveall idea
about exm...
imp subject for HAL are IC INGINE , MD ,SOM,TOM, EM......also some Qs from
MAnegment subject
total 100 qs all are tech.... ......
15 to 20 days deep study wiil crack the exm easily.............
7.The largest negative no can be represented with 8 bits in 2's compliment representation?
11.The model transform function of a All pass filter I know the ans but I can't type here?
13.For Tx line given Zoc and Zac then asked to find out characteristic impedance Zo?
Ans : Zo= sqrt of(Zsc*Zoc).
14. And for a tx line given L and C value asked to find out impedance of the tx line?
16. How the electric and magnetic fields are related in a EM wave?
18. Advance photo diodes are used more in opticalcommunicatoin compared to PIN
diode why?
A q's on potential barrier in diodes.
19. A ckt of voltage regulator is given and asked to find the load resistance.
22. A q's on FET amp to find Vds gives Vgs and Igs.
24. In AM given modulation index and total power asked to find out the carrier power?
GK(10) English(10) are easy u can do easily like oldest mountains (aravali mountains)
HAL PAPER
2. A system in which 2 or more cpu’s are interconnnected and share a common Main
memory is called:
(a) Pipeline machine
(b) Multifunctional system
(c) Multiprocess
(d) None of these
Q4. which of the following is/are true about 1's and 2's complements:
i)In 1's complement form. 0 has two representations
ii)in 1's complement, the magnitude of lowest number is equal to the magnitude of
highest number
iii)In 2's complement, 0 has two representations
Q5.if(base
{
cout<<"recovery stable"<
}
else
{
cout<<"recovery unstable"<
}
which of the values will print "recovery stable"?
a)base=8,height=8
b)base=3 height=2
c)base=5 height=3
d)base=4 height=7
ans:-d
Q7. which of the addressing modes require largest memory access time?
a)Direct
b)Indirect
c)base Index
d)PC relative
ans:b
Q8.Network Protocol doesn't consists of which of the following:
a)character Length
b)baud length
c)BIOS
d)none of these
ans:c
Q9.A token while passing from one token ring network to another requires the services
of:
a)a simple bridge
b)a transparent bridge
c)repeater
d)router
ans: b
Q14.calorimeter measures:
a)quantity of heat generated
b)heat radiation
c)temperature
d)none of these
ans:b
29. apttitude ques of pipes and cisterns, compound interest, time and distance, cubes, hcf
and lcm, multiplication,
34. there were 4 questions like if A*B represents Ais the son of B, C/D represents Cis the
husband of D then how A and D are related.
By,
Abhi
Questions were 160 in number,containing one mark each.Total=160 marks
Q1.Functional Dependency is:-
a)a type of constraint
b)data constraint
c)varies with time
d)none of these
ans:-a
Q4. which of the following is/are true about 1's and 2's compements:
i)In 1's complement form. 0 has two representations
ii)in 1's complement, the magnitude of lowest number is equal to the magnitude of
highest number
iii)In 2's complement, 0 has two representations
Q5.if(base<HEIGHT)
{
cout<<"recovery stable"<<ENDL;
}
else
{
cout<<"recovery unstable"<<ENDL;
}
which of the values will print "recovery stable"?
a)base=8,height=8
b)base=3 height=2
c)base=5 height=3
d)base=4 height=7
ans:-d
Q7. which of the addressing modes require largest memory access time?
a)Direct
b)Indirect
c)base Index
d)PC relative
ans:b
Q9.A token while passing from one token ring network to another requires the services
of:
a)a simple bridge
b)a transparent bridge
c)repeater
d)router
ans: b
By : Prashanth Tirungari
Hai friends,,
Here are the some of the technical questions posed in the HAL exam for the post of
Management/Design Trainee on 26-11-2006 for electrical branch.
4) What is the approximate peak overshoot for a unity feedback system with damping
factor 0.6?
a)10% b)5% c)15% d)20%
6) On no load in EHV lines what is the relation between receinving and sending end
voltage?
ans: receiving end voltage > sending end voltage
9) If both the juctions of transistor are forward biased, in wat region transistor works
ans: saturation region
10) Where is the hydel power plant located in following places?
ans: I dont remember the places
12) What is the GMD if the distance between the lines are 6m,6m,12m?
ans: 7.058m( approx)
15)There are two to three questions based on Laplace and Inverse Laplace transforms
17)When do two wattmeters show same value of opposite readings in two wattmeter
method
a) 300 lag
b) 600 lag
c) between 600 and 900 lag
d) zpf lag
ans: d
19) What is the value of resistance when both length and diameter of the wire are
doubled?
ans: halved
22) What happens to the value of inductance when self GMD is doubled?
26) What is the easier method for finding no. of poles in the right half of s-plane?
a) Niquist plot
b) R-H criterion
c) Root-Locus method
d) Polor plot
ans: b
27) How many no of poles located in the right half of s-plane for the characteristic
equation...
28) Burden of current transformers is measured in..
a) Watts
b) Volt Amperes
c) Ampere Hours
d) Joules
29)What is the gate used to get high output when all the inputs are low?
a) NOR
b) NAND
c) Ex-OR
d) Ex-NOR
ans: b
31) What is the line current of a circuit when the current transformer of 1000:5 rating
measures 4Amperes?
ans: 800A
32) If the time delay of relay with TMS setting 0.1 is 10 sec, then what is the time delaty
when the TMS setting is changed to 0.5
38) In the following locations where is hydal power plant is not located?
ans: i dont remember the places
45) What are the avg and rms values of full wave rectifier
ans: 2Vm/pie, Vm/21/2
Regards,
Prashanth Tirungari
Hello friends, this is Richa Gupta,B.Tech- EEE from (GZSCET Bathinda) with the help
of my friend Ridhima goining to give you the details experience of EIL-2009 which
we wrote on 15 March 2009. Paper was easy based on simple basics, covered all the
subjects of our engineering but max. ques were from Power System and Induction
motor.
Part-1
Out of 50 ques hardly 3-4 were of general English, no ques.is from aptitude the rest
all were GK ques.
5. Recently India has done "Science Express Deal" with which of the following
countries:
a) Germany, b) Japan, c) China, d) Russia
6. Pandit Jwaharlal Nehru award was given first time to the president of which of the
following countries:
a) Brazil, b) Mexico, c) Austria, d ) Sweden.
30. I would hope that you ____ take tea with me 2mrw.
a)shall, b) will, c) would, d) could
1. Dimensions of Power:
a) M1L2T-3, b) M1L2T-2, c) M1L1T-3, etc...
7. Those instruments which give constants and direction only are called:
a) Secondary type, b) Absolute type, c) Deflection type, d) Integrating type.
9. 1 ques like... If relay setting is at 125% and the CT ratio is 400/5, then the fault
current in hv winding is?
Ans. 6.25 amp.
10. If capacitve reactance of a 200 km line is 2000 ohm then what will be the
charging reactance of a 100 km line?
a) 2000 ohm, b) 4000ohm, c) 500 ohm, d) 8000ohm.
12. With the increase in feedback of the system which will increase:
a) stability, b) gain, etc...
15. Operation and maintenance cost is min. in which of the following plants:
a) Thermal, b) Nuclear, c) Hydel, d) Diesel.
18. The reflection coefficient for voltage of a short circuited line is:
a) -1, b) 1, c) 0, d) 2
20. If resistance of the secondary winding of the transformer is given as .02ohm and
reactance .06ohm then find out the primary resistance and reactance respectively:
Ans. .08 ohm and .24ohm
21. Skewing in the squirrel cage rotor of Induction motor is purposely done to :
Ans. to avoid interlocking and reduce noise.
23. The normal frequency RMS voltage that appears across the breaker poles after
final arc extinction is known as:
Ans. Recovery voltage
24. 1 ques like...... In power factor meter , which element is used as shunt in
instruments:
a) silver, b) copper, c) manganin, etc...
25. 1 ques like...If anode of the SCR is made positive and cathode is made negative
thenit will be:
Ans. forward biased and conducting.
31. On increasing the frequency of the transformer , hysterisis loss and eddy current
loss respectively:
a) decreases and remains same, b) decreases and increases, c) both
increases , d) both decreases.
36. Which of the following bridges is used to measure dielectric losses in capacitor:
a) Schearing Bridge, b) Wein's Bridge, c) De-Sauty Bridge, d) Maxwell
Bridge.
38. 1 ques like..... A full wave centre tap thyristor is given.. find out the PIV..? dnt
remember exactly some values were given...
a) 141.3 V, b) 100 V, c) 248.2 V, etc...
39. Speed of the Induction Motor at full load is 1400 rpm , what will be the speed at
half the load...
a)1400rpm, b) 1420rpm, c) 1440rpm, d) 1460rpm.
40. The line feeding from distribution system to the consumers is called:
a) feeder, b) service mains, c) distributor, etc...
44. Diac is a:
a) 4 terminal 2junction device, b) 3 terminal 2 junction device, c) 5 terminal 3
junction device, d) 6 terminal 3 junction device.
47. In Air Blast circuit breakers the air pressure inside is:
a) 1kg/cm2, b) 100 mm of Hg , c) 20-30 kg/cm2, d) 200-300 kg/cm2.
50. 1 ques like.... how the corona effect varies with size and frequency, it increases
with..
a) increasing size and reducing supply frequency, b) reducing size and incresing
supply frequency, etc...
51. 1 ques was based on..... in frequency variable method which of the following
factor is kept constant:
a) V/f = constant, b) Vf = constant, c)V=constant, d) none of these..
52. 1 ques was based on ..... relation of Voltage with load angle delta..... options
were...
a) V/1-& , b) V/1+&, c) 1-&/&V, d) &/(1-&)V
54. If CT winding connections are made in star/delta on the primary side of the T/F
then CT connections on the secondary side winding of T/F will be:
Ans. delta/star.
57. 1 ques like..... In cycloconverters the O/P frequency power factor will bw as
compared to I/P frequency power factor:
a) higher, b) lower, c) same..
62. 1 ques like....Two transformers are connected in parallel R/X is smthing..... then
the currents in the two T/F will be:
a) Ia lags Ib , b) Ia leads Ib, c) both will be in phase, etc....
69. Why earth pit is filled with alternate layers of salt and charcoal:
Ans. to reduce earth's resistance.
73. Which gas is used in the gas fired prime movers at gas power plants:
a) LPG, b) CNG, etc.
so friends, in the end i would like to say u that paper is not at all difficult ... if your
basics are clear...as u c ppr was theoretical type... hardly 4-5 numerical's were
there. so go through theory carefully...
Total 2hrs time for the test.
GK Question:
I am writing the question as I remember.
I am not writing the option , writing only correct option which i
remembered. RO: Right Option
Some more questions are given on current affairs, 5-6 questions are from english
grammer (easy) , if u have the habit of reading newspaper then that questions will be
easy. These are some questions from general awareness. (50 questions in this section).
Now coming to technical part, as I said that technical part was conceptual, so you
should have good knowledge of Fluid Mechanics, Mass Transfer, Heat Transfer, CRE,
Chemical Process Industries (CPI), Process Control .(question from these subject
were in major part)
As my point of view there are many objective books available for chemical
engineering, but O.P. Gupta & Ram Prashad is good books for all the PSU exams.
Prepare well for the exam. ALL THE BEST AND WISH U GOOD LUCK for your
future.
Your friendfriends, this is Richa Gupta,B.Tech- EEE from (GZSCET Bathinda) with the
help of my friend Ridhima goining to give you the details experience of EIL-2009
which we wrote on 15 march 2009. Paper was easy based on simple basics, covered
all the subjects of our engineering but max. ques were from Power System and
Induction motor.
Paper consists of 2 parts:
1. Non-tech. (50 ques.)
2. Technical (100
ques.) Duration: 2 hrs
Part-1
Out of 50 ques hardly 3-4 were of general English, no ques.is from aptitude the rest all
were GK ques.
ques. like...
5. Recently India has done "Science Express Deal" with which of the following countries:
a) Germany, b) Japan, c) China, d) Russia
6. Pandit Jwaharlal Nehru award was given first time to the president of which of the
following countries:
a) Brazil, b) Mexico, c) Austria, d) Sweden.
30. I would hope that you ____ take tea with me 2mrw.
a) shall, b) will, c) would, d) could
1. Dimensions of Power:
a) M1L2T-3, b) M1L2T-2, c) M1L1T-3, etc...
7. Those instruments which give constants and direction only are called:
a) Secondary type, b) Absolute type, c) Deflection type, d) Integrating type.
8. The internal resistance of a meter is 4 ohm and current drawn is 30mA. If we want to
increase its range as voltmeter upto 150V then find out the series resistance added in the
circuit?
Ans. 4996 ohm
9. 1 ques like... If relay setting is at 125% and the CT ratio is 400/5, then the fault current
in hv winding is?
Ans. 6.25 amp.
10. If capacitve reactance of a 200 km line is 2000 ohm then what will be the charging
reactance of a 100 km line?
a) 2000 ohm, b) 4000ohm, c) 500 ohm, d) 8000ohm.
12. With the increase in feedback of the system which will increase:
a) stability, b) gain, etc...
15. Operation and maintenece cost is min. in which of the dollowing plants:
a) Thermal, b)Nuclear, c) Hydel, d) Diesel.
18. The reflection cofficient for voltage of a short circuited line is:
a) -1, b) 1, c) 0, d) 2
20. If resistance of the secondary winding of the transformer is given as .02ohm and
reactance .06ohm then find out the primary resistance and reactance respectively:
Ans. .08 ohm and .24ohm
21. Skewing in the squirrel cage rotor of Induction motor is purposely done to :
Ans. to avoid interlocking and reduce noise.
22. 1 ques like.......capacitance of 3phase line is given 4microF. if we consider single line
to groundthen its capacitance will be:
a) 4microF, b) 2microF, c) 1microF, d) 8microF
23. The normal frequency RMS voltage that appears across the breaker poles after final
arc extinction is known as:
ans. Recovery voltage
24. 1 ques like...... In power factor meter , which element is used as shunt in instruments:
a) silver, b) copper, c) manganin, etc...
25. 1 ques like...If anode of the SCR is made positive and cathode is made negative thenit
will be:
ans. forward biased and conducting.
31. On increasing the frequency of the transformer , hysterisis loss and eddy current loss
respectively:
a) decreses and remains same, b) decreases and increases, c) both increases , d)
both decreases.
32. Rotor copper losses are small in Induction Motor as compared to transformer becoz:
Ans. Rotor core is laminated.
33. 1 ques like.... arrange the following in ascending order:
resistance split, capacitor start capacitor run etc motors were given...
36. Which of the following bridges is used to measure dielectric losses in capacitor:
a) Schearing Bridge, b) Wein's Bridge, c) De-Sauty Bridge, d) Maxwell Bridge.
38. 1 ques like..... A full wave centre tap thyristor is given.. find out the PIV..? dnt
remember exactly some values were given...
a) 141.3 V, b) 100 V, c) 248.2 V, etc...
39. Speed of the Induction Motor at full load is 1400 rpm , what will be the speed at half
the load...
a)1400rpm, b) 1420rpm, c) 1440rpm, d) 1460rpm.
40. The line feeding from distribution system to the consumers is called:
a) feeder, b) service mains, c) distributor, etc...
44. Diac is a:
a) 4 terminal 2junction device, b) 3 terminal 2 junction device, c) 5 terminal 3
junction device, d) 6 terminal 3 junction device.
47. In Air Blast circuit breakers the air pressure inside is:
a) 1kg/cm2, b) 100 mm of Hg , c) 20-30 kg/cm2, d) 200-300 kg/cm2.
50. 1 ques like.... how the corona effect varies with size and frequency, it increases with..
a) increasing size and reducing supply frequency, b) reducing size and incresing supply
frequency, etc...
51. 1 ques was based on..... in frequency variable method which of the following factor is
kept constant:
a) V/f = constant, b) Vf = constant, c) V=constant, d) none of these..
52. 1 ques was based on ..... relation of Voltage with load angle delta..... options were...
a) V/1-& , b) V/1+&, c) 1-&/&V, d) &/(1-&)V
54. If CT winding connections are made in star/delta on the primary side of the T/F then
CT connections on the secondary side winding of T/F will be:
Ans. delta/star.
57. 1 ques like..... In cycloconverters the O/P frequency power factor will bw as
compared to I/P frequency power factor:
a) higher, b) lower, c) same..
62. 1 ques like....Two transformers are connected in parallel R/X is smthing..... then the
currents in the two T/F will be:
a) Ia lags Ib , b) Ia leads Ib, c) both will be in phase, etc....
69. Why earth pit is filled with alternate layers of salt and charcoal:
Ans. to reduce earth's resistance.
73. Which gas is used in the gas fired prime movers at gas power plants:
a) LPG, b) CNG, etc.
Section - I
1. First women Prime minister in the world…..
a) S.Bandarunaike b)……..
2. In the following countries which is not included in SARC?
a) India b) Pakistan c) Afghanistan d) Srilanka
3. The No of judges is in the Supreme Court sit in front of main justice ……
a) 36 b) 24 c) 30 d) 28
4. The % of forests in India …….
a) 6% b) 19% c) 22.5% d) 28%
5. On which date & year Indian constitution came into force….?
6. Which state having highest costal line In India?
a) Orissa b) Karnataka c) Andhra Pradhesh d) Kerala
7. The No of spokes in Ashoka chakra…..
a) 36 b) 24 c) 30 d) 28
8. In which state ‘sun temple’ is located?
9. In India which crop depends on mainly on rainfall?
a) Paddy b) wheat c) barja d)….
10. From which form government gets more Income?
a) direct taxes b) indirect taxes c) interests d)…..
11. Which income is not shared by state govt. from central govt.
a) i/c tax b)……..
12. The first Indian educational satellite launched by ISRO is
a) EDSATILL b) EDUSAT c) EDUSALLL d) SATEDUCATION}
13. In which place Indian Institute of ocean Technology is located?
a) Mumbai b) Hyderabad c) Bangalore d) Chennai
14. The fast Bowler who claims the hat trick wickets in ODI match.
15. Who became the captain of Indian team at the youngest age?
16. In the following which is not the function of vitamins
a) to give energy b) In digestion c)……..
17. Who got the ‘raman megasis’ award?
a) M.Swaminathan b)……..
18. The 2006 commonwealth games are conducted in ….
a) London b) Melbourne c) Switzerland d)…..
19. On which matter recently Benajeer Butto appears in News?
20. On which day we celebrate the youth day?
a) jan 9 b) jan 12 c) jan 24 d) jan 31
21. world health day ……… march 12 / april 24 / oct 15………
22. The first deputy PM of India
a) sardhar patel b) Rajendra Prasad c)…….
23 ‘Geetanjali’ is written by Tagore / Rajendra Prasad / sardhar patel
24. The famous Orissa dancer………..
25. The parliment ‘Nityanidhi’ belongs to
a) Nepal b) …… c) Bangladesh d)….
26. The famous Indian who spoke ‘ jai javan jai kisan’
a) sarjioni devi b) Indira Gandhi c) Rajaram d)………..
Up to 50.
/////////////////////
Section - II
51. The resistance of earth wire in ohm is ………..
a) 1 b) 20 c) 100 d)……….
52. In which connection the distribution T/F is connected?
a) ▲ / Y b) Y / ▲ c) ▲ / ▲ d) Y / Y
53. Skin effect is proportional
a) f b) f2 c) doesn’t depend on f d)……..
54. A 3P supply is connected in Y connected Resistance. If one of the resistors is
removed then the % of reduced load is
a) 33 1/3 b) 50 c) 66 2/3 d) 75
55. A 25MVA 3300/400V T/F is termed as per winding is ……
a) primary 3300V & Secondary 400V
b) primary 3300V & low voltage winding 400V
c) High voltage winding 3300V & Secondary 400V
d) High voltage winding 3300V & low voltage winding 400V
56. T/F oil is useful for ……..
a) protection & cooling b)… c)………….
57. Buchholz relay is used ……….
a) protection T/F b) oil T/F c) Air core T/F d)……..
58. Resistor switching is used in which type Circuit Breaker?
a) oil filled CB b) Air blast CB c) Gas filled CB d)……..
59. Comparing to AC transmission, corona & R in DC transmission is…….
a) lower b) higher c) same d) ………..
60. Form factor is the ratio of ………
a) peak to avg b) rms to avg c)…. d)……..
61. To transmit the Power which must be present…?
a) Reactance b) Resistance c) Capacitance d) none of above
62. If the characteristic Impedance is equal to load Impedance then……
a) voltage will be increased b) power transmission is zero c) …… d) max. power
is transmission to load
63. In general the conductor used in transmission system is
a) cu b) ACSR c) ………… d)……..
64. In EHV tranm. The conductors are ……..
a) Cu roads b) Cu bars with Si c) Cu tube with Si plate d)…….
65.The normal highest generated voltage in India is
a) 6.6KV b) 132KV c) 11KV d)……..
66 From the point of economy, the voltage of transm. is…….
a) small b) medium c) high d) very small
67 In general the insulation of conductor depends on
a) lighting Voltage b) switching V. c) surge vol. d)……….
68. the max. power will be transferred if ……
a) sending end vol. is high b) receiving end v is high c)…….. d) corona loss is
least
69. By which compensation the stability is increased
a) shunt compns b) series compn c) .. d)……
70. Meggar is used for measuring ……..
a) low resistance b) medium resi c) high & insulation resis
71. Moving Iron instruments are applicable with
a) DC only b) AC only c) DC & AC
72. Meggar is used to find the resistance in
a) short ckt condition b) O/C cond c) at high resistance
73. Inductance is measured by ……
a) weins bridge b) Schering c) Maxwell’s bridge d)…..
74. low resistance is measured by…….
a) resistance box b) Anderson bridge c) Kelvin-double brdg d)….
75. Induction type 1-p wattmeter reads …..
a) true value b) apparent value c)volt ampere value d)……..
76. The string chat is used for
a) To measure Insulation b) To decide the distance b/w towers c)…. d)..
77. The string effcy in AC sys is 80% Then for same power, the string effcy in dc sys is
a) less than 80% b) 80% c) more than 80% d) zero
78. The machine with same rating, with increase in voltage then …….
a) size increases b) cost increases c)……. d)……
79. The temperature rise in the sys, which leads to …..
a) Increases stress& length b) increases stress but decreases length c) Decreases stress
& increase length d) decrease stress & length
80. The min. distance from cable to foundation of Building is ……..
a) 1cm b) 10cm c) 100cm d)1000cm
81. In single core cable which is not present
a) sheath b) steal armouring c)…
82. The component which is the ore of lead.
a) ceramic b) citric c)……
83. To absorb the lighting surges which of the following is used…?
a) Breather b) Conservator c) Horn Caps d)….
84. The coefficient of reflection in open ended transmission is
a) -1 b) 0 c) α d) 1
85. For 50KVA & 132KV base voltage base voltage, the p.u. impedance is 0.4 ohm then
for 100KVA & 132 KV base voltage then the p.u impedance is ….ohm
a) 0.4 b) 0.8 c) 0.2 d) 1.6
86. According to underground cables
a) stress b/w sheath & conductor is high b) inrush of core & conductor c)……. d)
…
87. The corona effect is more in
a) summer b) winter c) dry weather d) humidity weather
88. One joule cycle is
a)…. b)……
89. One Q. depends on energy meter, ie which measures power in general ( not
exactly…….)
a) ampere hour meter b) volt-ampere meter c) watthour meter d)…….
90. In radial network the source is fed from
a) One end b) both ends c) at central d) ……..
91. In Indicating instrument some error is shown when meter is in full scale deflection,
then error is
a) same for half scale def. b) same at any deflection c) less than full-scale def. d)
half at half scale def.
92. The reactive power at the load end
a) Proportional to sending end vol. b) Proportional to line vol drop. c) Proportional
to line reactive vol drop d)……..
93. Which of the following is high speed turbine
a) wind b) steam c) hydro d)……
94. The steady state stability limit is max. when…..
a) low regulation voltage b) high sending end voltage c) low line reactance d)
………. EIL PAPER ON 6th APRIL AT BANGALORE
Hi friends, This is shiva, I am from instrumentation background. I had attended for the
Engineers India Limited (EIL) exam on 6th April, 2008 in Bangalore . Before that I want
to reveal one thing, before few days I have searched for the eil papers in freshersworld,
but I cant get anything, so I am uploading this after I attended for the exam. I think it
may be useful for anyone of freshersworld visitors……..
Getting into the details…………
In whole test paper there is no aptitude questions n one more imp thing is negative
marking is there, for every wrong answer 1/4th mark will be deduced. The paper
comprises of 150 questions, 50 are General awareness and remaining 100 are technical
questions. All are multiple choice questions.
Some more questions are given on current affairs, if u have the habit of reading
newspaper then that questions will be easy. These are some questions from general
awareness. (50 questions in this section).
Coming to the Technical paper, it will consist of 100 questions. Since I am from
instrumentation background.
Prepare well for the exam. ALL THE BEST AND WISH U GOOD LUCK for your
future.
Regards,
Venkata Siva. V
95. Synchronous M/C with under excitation with reactive power absorption , acts as
a) synch. Motor b) synch gen c) synchr capacitor d)……..
96. Q based on pettier ▲le ……..ie what’s the ratio of resistance something
like……………..
97. At the time of Arc extension ,the arc quenching at
a) zero vol b) zero current c) maxi vol d) maxi current
98. Over excited operation of Syncr M/C is for….
a) lead compensation b) lag cmp. c) lead lag com. d)……..
99. A 10KVA T/F having cu loss at full load is 1600W, when operated at half load the cu
loss would be in W
a) 800 b)1600 c) 200 d) 400
100. The rating of syncs gen is 75KW at 0.8 pf means……
a) The m/c delivers 75kw to lagging loads only
b) The supply for gen is 75kw at 0.8 power factor
c) The rating of gen is 75kw and gives 0.8 pf lagging
d) ………
101. One Q depends on armature reaction………what is the cause of
demagnetization……..
102. The skin effect is minimum when the conductor is in the shape of……
a) circular b) flat c) oval d) hallow
103. Damper bars used in syn gen is to …
a) reduce the losses b) produce the induction action c) reduce unbalances d)…….
104. The o/p of controller is given to…
a) sensor b) amplifier c) processor d)….
105. PID controller is used for which type of compensation……
a) lead comp. b) lag com. c) lead lag com. d)……
106. One simple Q based on Root locus…..
107. The gain margin or phase margin r calculated to find the…….
a) time response b) f resp. c)…….. d)……
108. In a 3p full converter the conducting angle b/w two diodes is
a) 60o b) 90o c) 1200o d) 120o
109. To fed the Rl Load ,How many components are in 1p inverter ...
a) 2 diodes b) 2 thy 2 D c) 2 Thy d)……
110. One Simple Q on overlapping of two thyr
111. Two more Q on Basics of PE
113. According to Thyr wnhich of the foll is correct?
a) holding curnt > latching crnt
b) holding curnt < latching crnt
c) …...
………..
………….
……………..
149.
150.
That’s allllllllll
//////////////////////////////
The qns are from just basics of over all subjects……………..
So prepare welllllllll . definitely u ll get through…………….
Still we r also waiting for result…….may take 1 month………….
ALL THE BEST
Posted by
Naresh & Bhaskar
Hi friends, This is shiva, I am from instrumentation background. I had attended for the
Engineers India Limited (EIL) exam on 6th April, 2008 in Bangalore . Before that I want
to reveal one thing, before few days I have searched for the eil papers in freshersworld,
but I cant get anything, so I am uploading this after I attended for the exam. I think it
may be useful for anyone of freshersworld visitors……..
Getting into the details…………
In whole test paper there is no aptitude questions n one more imp thing is negative
marking is there, for every wrong answer 1/4th mark will be deduced. The paper
comprises of 150 questions, 50 are General awareness and remaining 100 are technical
questions. All are multiple choice questions.
Some more questions are given on current affairs, if u have the habit of reading
newspaper then that questions will be easy. These are some questions from general
awareness. (50 questions in this section).
Coming to the Technical paper, it will consist of 100 questions. Since I am from
instrumentation background.
Regards,
Venkata Siva. V
Hi friends,Here are the some of the technical questions posed in the NALCO exam for
the post of Graduate engineering trainee on 28 oct. 2007 for Electrical branch. Out of 120
questions 60 technical questions, 60 non-tech questions and time duration was 2 and half
hours.
There were still more question but I couldn’t remember all of them. The questions mostly
have taken from electrical handbook, gate papers. Almost all questions were come simple
basics.
CHANDRAMOHAN
DATE: - 4th AUGUST, 2008
COLLEGE: - KALYANI GOVT. ENGG. COLLEGE, WEST BENGAL
Hi, I m Sougata Pani, (Information Technology) from Kalyani Govt. Engg. College,
WestBengal . I got selected in Vedanta Resources through campus interview in our
college. I want to share my experience with u.
Eligibility Criteria
1. The candidate must not have crossed 24 years of age as on 30 Sept, 08.
2. The candidate must have achieved first class in his/her 10th & 12th with
first/single attempt. And no year gaps in between.
3. The candidate must be having no Keep Terms/ Backlogs history and must have
got above aggregate of 60% or first class in his/her engineering.
4. The candidate should not have more than one-year gap between 12th and
Engineering admission.
No Diploma / Lateral entry engineers.
5. They should be medically fit as per our medical norms, eye power should be
within limit of +/- 4 with no color-blindness.
One important thing about VEDANTA is that they are very strict about their Eligibility
Criteria. They are not relaxing the criteria whatsoever.
The written exam was a set of 35 easy simple questions to be completed in 50 mins .You
need not be an expert to solve these questions. Only 2 questions came from Verbal
Ability. It was a simple analogy. Another was a word meaning. There was a set of 6
puzzle problems where one has to identify A,B,C,D,E,F. Relevant informations were
given.
The APTI part was simple Class 10 questions involving simple SPEED-TIME-
DISTANCE problems (4questions on train crossing each other) , few numerical
sequential problems, simple Profit-Loss-Discount problems ( 3-4), there was set of 5-6
graphical interparatation problem ( between Demand and Supply of 3 companies), Few
Age problems, problems on simple Probability, Percentage problems…
4. A train of 110 mtr long is running at 60 kmph . In what time it will pass a man
who is running at 6 kmph in the direction opposite to train ?
ans – 6 sec.
5. A radio when sold at a certain price gives a gain of 20%. What will be the gain percent,
if sold for thrice the price?
A) 260%
B) 150%
C) 100%
D) 50%
Ans: 260%
Of the six men of literature A,B,C,D,E and F being considered here, two belonged to
the 17th century, three to the 19th and one to the 20th century. Four were recognized
as great poets, three as great novelists and three as great dramatists. One
contributed to Bengali literature, two to Hindi, two to Marathi and one to Tamil. The
20th century writer wrote poetry only and contributed to Marathi literature and the
other Marathi writer contributed to poetry, novel and drama. One Hindi writer and
the only Tamil writer belonged t other 19th century. The former contributed to poetry
and novel while the latter to novel and drama. The Bengali writer belonged to the
17th century and contributed to poetry only. A belonged to the 20th century, B wrote
drama only, C contributed Marathi literature, D was a Hindi Poet and novelist and
belonged to the 19th century. E also belonged to the 19th century, and F contributed
to Poetry only.
I cleared the written exam. Then there was GD round… each group have 6 members
….
Results were out br 8.00 Pm, I was happy that i was selected...our offer intimation
letters were given on the same day..
So friend don’t upset if u not selected in this company… then u think that there r
better company wait for u…
I attended so many campus interviews in our college. At last I selected in the better
company i.e. VEDANTA.....
Test Paper :4
There were separate marks for written test, GD & Interview. The sum total of all the
marks was taken for the final results. Although the written test was the only elimination
round, they didn’t eliminate anyone in the GD.
Eligibility Criteria:
1. Ist class in Ist attempt in 10th 12th and in BE
2. Aggregate 60% in 10th 12th & BE
3. No history of Backlog
4. Maximum 1 year gap between 12th & BE
5. No gap b/w 10th & 12th
6. Must be medically fit (no colour blindness)
2nd Round:-
The ppt was followed by a written test. It consists of 35 questions to be completed in 45
minutes. The questions were very simple but speed was the main factor. There was no
negative marking in the written test.
The aptitude questions were simple but time management is very important. They were
mainly from both R.S. Aggrawal. The topics were- Average, Problems on ages,
Percentage, Profit & Loss, problems on train, ratio, numbers, probability, chain rule,
volume & surface area, series completion, coding& decoding, analogy(verbal), venn
diagram, syllogism.
For Data interpretation, refer RS Aggrawal- quantitative aptitude.
3rd Round:-
The written test was the elimination round. It was followed by a Group Discussion. Out
of 28 students 18 were selected for G.D.
don’t forget to go in the GD room with a pen & a register, they had given us one minute
to think on the topic. They checked our registers what we had write in the register in
that one min.
4th Round:-
The last round was the Interview. The interview consists of Technical + HR
INTERVIEW
1. What about ur GD?
2. Tell me about yourself?
3. Reason for one year drop?
4. Future ambition?
5. Favourate subjects?
I have said microprocessor, transformer and machines. But he didn’t ask me any
question from microprocessors.
6. Transformer rating in KVA but motor rating in KW, why?
7. What is power factor?
8. What is active and reactive power, difference?
9. What are the effects of reactive power, how can you reduce the effects of reactive
power?
10. What is capacitor bank, how it works?
11. When reactive power enters the system, what happens in the system?
12. Can u explain all this technical terms to any laborer, worker?
13. different tests on the transformer, and their details?
14. conditions for parallel test?
15. types of faults, what are symm. And asymm. Faults?
16. At last the result was announced.
Test Paper :5
Hi friends...
I m arun doing my final eee in sengunthar engg college, thiruchengode. I got
placed in VEDANTA GROUPS on 29.01.2008. I m very happy to join in vendanta
family... I like 2 share my experience with all of u.. so that it may help u....k..
First the company is very very strict in thier eligible criteria... If u r eligible 2 the
following criteria only u can attend...
ELIGIBLE CRITERIA
u must scored 1st class in 10th,12th, completing the B.E. course with a first class
(60%) in the first attempt. NO backlocks should b there...
APTITUDE ROUND
The first round was very easy only.... It contains 35 Questions U should answer
within 50 mins..
5. Meanings (2)
6. Percentage (3)
7. Profit and Loss (3)
U need not b a expert 2 solve tis problem.. just go through R.S. Agarwal book...Just
c the formula d solve d practice 1 r 2 problems..its enough...
While solving the questions during exam...Try 2 solve bar charts d analytical venn
diagram first.. so that u can score easily..
GROUP DISCUSSION
This is also easy.. u just speak out its enough.. but u should open ur mouth.. dont
worry about the grammer.. do confidently....
HR + TECHNICAL
This round i like it very much...Dont b worry abt the technical questions.. it is very
very basic only.. what term u r saying from ur mouth.. they wil ask questions from
that...just open ur mouth..say something r say i dont know.. they wil help u to
answer the questtions...b frank what u know.. tel ur area of intrest they wil ask
from that.. r else learn basics in CONTROL SYSTEM and MEASUREMENT and
INSTRUMENTATION...
They wil ask ur aim d family background.. u just b frank d tel something.. they
need communication not the grammer r knowledge... b confident...b bold...b
smiling face...they wil surely select u....
-arunkumar.k
Hi, I m Shivshankar Podder, (electronics n comm.) from NIT, Bhopal . I got selected in
Vedanta Resources through campus interview in our college. I want to share my
experience with u.
** There were separate marks for written test, GD & Interview. The sum total of all the
marks was taken for the final results. Although the written test was the only elimination
round.
The session started with the PPT. It was of 1 hr. The ppt was followed by a written test. It
consists of 35 questions to be completed in 50 minutes. The questions were very simple
but speed was the main factor. The written consists of
• 20 aptitude questions (simple maths)
• 5 questions- venn diagram
• 5 questions- Data Interpretation
• 5 questions – Logical reasoning
The aptitude questions were very simple. They were mainly from R.S. Aggrawal. The
topics were Average, Problems on ages, Percentage, Profit & Loss, problems on train,
volume & surface area, series completion, coding& decoding,
Analogy questions( Barron’s GRE 12th edition- chapter 4)
The written test was the elimination round. It was followed by a Group Discussion.
The topic for our group was “SHOULD THE INDIAN COMPANIES RECRUIT
FOREIGN PEOPLE”
The last round was the Interview. The interview consists of Technical + HR
INTERVIEW
1) Tell me about yourself?
2) Tell me about your family background?
3) Question on my CV?
4) Difference b/w electronics & comm Engg and Electronics & Instrumentation Engg
5) What is instrumentation?
6) Are you interested in Software or core?? Why??
7) Questions from PPT
8) Do u have any relocation problem?
9) What is the difference between Microcontroller and Microprocessor?
10) Architecture of Intel’s 8085
11) What is accumulator, Program counter, stack pointer?
12) What is stack?
13) Difference between 8085 and 8086
14) What is the difference between analog and digital communication?
15) Questions on Vocational training
16) Status flag and PSW in 8085
17) Multiplexers and decoders
18) What is 3G?
19) Are you really interested to work in our company??
20) Do u want to ask any question??
At last the results were announced. Total 16 students got selected. I was the only one
from the Electronics n comm. Just be confident on whatever you know.
The selection procedure is very easy .Screenining of students are take place in four steps
1. very tough eligiblity creteria
2.written test(totally apptitude)
3.G.D(very very small chance)
4.Interview(technical+hr both at a same time)
Eligiblity creteria is u donot have more than one yr drop.there should be no backlog in
whole semesterand u must have adegree of more than 60%
written test will be very easy and u can easily score more than 90% marks,so don,t worry
in our college they didn,t took G.D
By,
Test Paper :8
There are total 35 Questions, Most of them are directly from R.S. Agrawal, very
easy,Total time allotted was 50 mins.
1. Find the next term of series
0, 6, 24, 60, 120, 210, 210, ?
ans - 336
2. Preamble: Constitution ::
ans- Book: Preface.
3. Greed: Corruption ::
Ans - Guilty: Enemy
4. There are some no. of men and horses , After some time half of the men left, then total
no. of legs (of men and horses) will be 70, find the no of horses.
Ans – 14
5. If a train runs at 40kmph it reaches its destination late by 11 mins,but if it runs at
50kmph then it late only by 5 mins The correct time to complete its journey is-
ans- 19 mins
6.A train of 110 mtr long is running at 60 kmph . In what time it will pass a man who is
running at 6 kmph in the direction opposite to train ?
ans – 6 sec.
7.
if x = y+2;and xy = 24 then z= ?
The diagram given below shows the no. of students who got distinction in three subjects
out of 500 students. Study the diagram and give the ans.
11. What is the percentage of students who got distinction in two subjects ?
ans- 8%
12. What is the % of students who got distinction ?
ans 38 %
13. The % of students with distinction marks in maths is –
ans 17.8%
14. Statements :-
some bananas are apple.
All apples are tomatoes.
Some potatoes are tomatoes.
Conclusion :
(I)Some bananas are tomatoes.
(II)Some potatoes are bananas.
(III)Some apples are potatoes.
(IV)Some apples are bananas.
Ans- Only (I) and (IV) follows.
Dear Friends,
Normally when we go through placement paper website we seldom come across papers
of Tech/Core companies. But we have made a humble beginning………Anyways,
VEDANTA came to our college on the 6th of August. In the mail that was sent to our
college it was mentioned that VEDANTA requires 785 GET. So friends the requirement
at VEDANTA is Huge…….So they are recruiting in Large numbers from the colleges
they are visiting.
Eligibility Criteria : 60% and above throughout in Secondary, +2 and in all semesters
(till date); No backlogs; Vision max -4 D ; Maximum 1 year drop after +2 b4 u join
college ;
One important thing about VEDANTA is that they are very strict about their Eligibility
Criteria. They are not relaxing the criteria whatsoever.
1. Written
2. Interview ( Tech & H. R )
The written exam was a set of 35 easy simple questions to be completed in 50 mins .You
need not be an expert to solve these questions. Only 2 questions came from Verbal
Ability. It was a simple analogy. Another was a word meaning. There was a set of 6
puzzle problems where one has to identify A,B,C,D,E,F. Relevant informations were
given.
The APTI part was simple Class 10 questions involving simple SPEED-TIME-
DISTANCE problems (4questions on train crossing each other) , few numerical
sequential problems, simple Profit-Loss-Discount problems ( 3-4), there was set of 5-6
graphical interparatation problem ( between Demand and Supply of 3 companies), Few
Age problems, problems on simple Probability, Percentage problems…
This is all that I can recall at present but I can assure you that all the questions were very
easy and less time consuming.
The interview was very simple. Hardly any tech questions were asked.. Almost all the
guys who sat for the interview were selected. Out of the 35 students who were eligible to
sit only 13 qualified for the written out of which 12 were finally selected.
• First 5 questions were based on a bar dia. about demand and production.
• It was followed by quantitative part consisting of following chapters
diff. geometrical shapes were related with each other and based on that 5 questions were
asked. (refer R.S. Aggrawal verbal and non-verbal reasoning)
Written test was easy to crack. Out of 27 students 19 were selected for G.D. but somehow
G.D. was cancelled. Next was the technical interview along with HR. And finally out of
19, 12 were selected. Believe in yourself. They need honest, energetic and confident
candidates.
Regards,
Harshit Anada.
Hi friends .i am final year student of chemical engineering got placed in vedanta this was my 7th
company,so always keep patience and confidence and wait for a lucky day.
the company expects that you fulfill technical skills and have general command on the core subjects.On
27th august vedanta conducted campus drive for our batch in which students of the branches EEE, ECE,
MECH, ICE AND CHEMICAL participated.
totally 37 students appeared out of which 21 cleared the aptitude test out of which 12 were selected for the
interview after GD and finally 4 out of 12 were selected.
for the INTERVIEW,they will ask questions regarding your area of interest ,industrial training ,industrial
visit(if any) and some easy questions from mccabe,like types of heat exchangers ,steam traps,flow
characterstics of fluid,name of some heat transfer equipments,some of the mechanical operations name...so
technical will be easy,they just ask basic questions...if you have one year break in studies.than you should
carry some proof in interview because they are very strict regarding this.
Be confident and always have faith in yourself and keep a smiling face in interview.
ANAND MOHAN.
The company is generally requiring only persons with full of confidence and engineering
knowledge,they basically donot select people for the sake of selecting some nos they
expect when they come to college.They usually select people who is having 60% start
from X and till the latest course of study with no history of arrears even in X or XII TH
also ,they donnot take diploma holders.
In my collge we started with 34 and the elimination process was not very harsh and hence
30 were selected,after that GD inwhich they give chances to everyone and it was
encouraging. BUT 17 were selected for the next round.Finally there comes interview
which was very easy for me and they asked only some basic engineering questions. But
you should be serious while attending and not so cool ,better dont eat or drink any thing
they give bcse my friends were rejected for their cool answers and not being serious.
DEAR FRIENDS,
WRITTEN PAPER CONTAIN 35 Q,SOMPLE
MATHS(P&L,PERCENTAGE,AVERAGE,VENN DIAGRAM(5Q),ONE PASSAGE IS
THERE LIKE(5 TEACHERS R THERE HAVING DIFFERENT INTERESR...U HAVE
TO FIND WHAT THESE PEOPLE R INTERESTED.......VERY SIMPLE ..REFER R.S.
AGGARWAL)
BY,