Professional Documents
Culture Documents
LMD-1420
LMD-1410
SERVICE MANUAL
1st Edition
! WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
LMD-1420/1410
Table of Contents
1. Service Overview
2. Electrical Alignment
3. Troubleshooting
4. Spare Parts
LMD-1420/1410 1
5. Block Diagrams
2 LMD-1420/1410
Section 1
Service Overview
BA board
S board
J board
LMD-1420/1410 1-1
1-3. Disassembly
7 Three
5 Three hooks hooks
2 Stand
Cushion
1-3-2. Q Board
. Remove the rear cover. (Refer to Section 1-3-1.)
1 Two screws
(PWH3 x 6)
9 Two screws
(PSW3 x 12)
!/ AC holder
4 Screw 7 Two screws
(PSW4 x 8) (PWH3 x 6)
5 Harness
8 Q board
6 Two screws
(PWH3 x 6)
!- AC inlet
Cushion
1-2 LMD-1420/1410
1-3-3. GA Board
. Remove the rear cover. (Refer to Section 1-3-1.)
1 Three harnesses
2 Five screws
(PWH3 x 6)
3 GA board
Cushion
1-3-4. Inverter Board/BA Board
. Remove the rear cover. (Refer to Section 1-3-1.)
. Remove the Q board. (Refer to Section 1-3-2.)
6 Ten harnesses
4 Four screws
(PWH3 x 6) 7 Five screws
(PWH3 x 6)
3 Five harnesses
8 BA board
5 Inverter board
Cushion
LMD-1420/1410 1-3
1-3-5. DC Fan/Speaker
. Remove the rear cover. (Refer to Section 1-3-1.)
. Remove the Q board. (Refer to Section 1-3-2.)
5 Screw
(PWH3 x 6)
1 Screw
(PWH3 x 6) 8 DC fan
!] DC fan !; Speaker
![ Two screws
(B3 x 14)
Cushion
1-3-6. J Board
. Remove the rear cover. (Refer to Section 1-3-1.)
. Remove the Q board. (Refer to Section 1-3-2.)
1 Two screws
(PWH M3 x 8)
3 J board
2 Harness
6 AC cover
5 Three hooks
4 AC button
Cushion
1-4 LMD-1420/1410
1-3-7. LCD Panel
. Remove the rear cover. (Refer to Section 1-3-1.)
. Remove the Q board. (Refer to Section 1-3-2.)
. Remove the GA board. (Refer to Section 1-3-3.)
. Remove the inverter board and BA board. (Refer to Section 1-3-4.)
. Remove the DC fan and speaker. (Refer to Section 1-3-5.)
. Remove the J board. (Refer to Section 1-3-6.)
1 Screw
(PWH3 x 6)
2 Cable retainer
4 Four screws
3 Four screws
(PWH M3 x 8)
(PWH M3 x 8)
5 Main frame
8 LCD panel
!/ Two cushions
9 Two cushions
!- Protection plate
7 Two screws
(PWH3 x 6)
6 Two screws
(PWH3 x 6)
Cushion
LMD-1420/1410 1-5
1-3-8. H Board/X Board (X Board: LMD-1420 only)
. Remove the rear cover. (Refer to Section 1-3-1.)
. Remove the Q board. (Refer to Section 1-3-2.)
. Remove the GA board. (Refer to Section 1-3-3.)
. Remove the inverter board and BA board. (Refer to Section 1-3-4.)
. Remove the DC fan and speaker. (Refer to Section 1-3-5.)
. Remove the J board. (Refer to Section 1-3-6.)
. Remove the LCD panel. (Refer to Section 1-3-7.)
1 Harness
2 Six screws
(PWH M3 x 8) 3 H board
4 Harness
5 Two screws
(PWH M3 x 8)
6 X baord
(LMD-1420 only)
7 ESD plate
Cushion
Boards requiring use of unleaded solder are printed with a lead free mark (LF) indicating the solder
contains no lead.
(Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular
size.)
m
. Be sure to use the unleaded solder for the printed circuit board printed with the lead free mark.
. The unleaded solder melts at a temperature about 40 dC higher than the ordinary solder, therefore, it is
recommended to use the soldering iron having a temperature regulator.
. The ordinary soldering iron can be used but the iron tip has to be applied to the solder joint for a
slightly longer time. The printed pattern (copper foil) may peel away if the heated tip is applied for too
long, so be careful.
1-6 LMD-1420/1410
1-5. Warning on Power Connection
LMD-1420/1410 1-7
Section 2
Electrical Alignment
LMD-1420/1410 2-1
Section 3
Troubleshooting
Are harness
No Connect the harness and
and flexible flat cable
connected correctly? flexible flat cable correctly.
Yes
No
No
LMD-1420/1410 3-1
3-2. System does not start
Are harness
No Connect the harness and
and flexible flat cable
connected correctly? flexible flat cable correctly.
Yes
No
Is the symptom No
improved when another Replace the J board.
J board is installed?
Yes
Are harness
No Connect the harness and
and flexible flat cable
connected correctly? flexible flat cable correctly.
Yes
Is the symptom
improved by the external No
Replace the BA board.
operation of PARALLEL
REMOTE terminal?
n
Yes For the external operation of PARALLEL REMOTE terminal,
refer to the Operating Instructions.
3-2 LMD-1420/1410
3-4. Image is abnormal
Image is abnormal.
Are harness
No Connect the harness and
and flexible flat cable
connected correctly? flexible flat cable correctly.
Yes
No
No
Yes
No
LMD-1420/1410 3-3
3-6. Output function is abnormal
Fan is abnormal.
Are harness
No Connect the harness and
and flexible flat cable
connected correctly? flexible flat cable correctly.
Yes
Yes
Yes
Is the symptom improved? No problem.
No
No
3-4 LMD-1420/1410
Section 4
Spare Parts
2. Standardization of Parts
Some repair parts supplied by Sony differ from those
used for the unit. These are because of parts common-
ality and improvement.
Parts list has the present standardized repair parts.
3. Stock of Parts
Parts marked with “o” at SP (Supply Code) column of
the spare parts list may not be stocked. Therefore, the
delivery date will be delayed.
4. Harness
Harnesses with no part number are not registered as
spare parts.
In need of repair, get components shown in the list and
repair using them.
LMD-1420/1410 4-1
Overall Block
4-2. Exploded Views
PWH4 x 14
PWH4 x 14
PWH4 x 14
14
PWH
3x6
PWH3 x 6
2
PWH3 x 6
19 PSW3 x 12
PWH3 x 6
PWH
3x6
PWH3 x 6 PSW4 x 8
8
PWH3 x 6
11
9
PWH
PWH3 x 6 3x6
PWH3 x 6
PWH3 x 6
PWH
M3 x 8
PWH M3 x 8
B3 x 14
3
PWH M3 x 8
4
PWH3 x 6
P2 x 14
PWH3 x 6 4
PWH3 x 6 P2 x 14 PWH3 x 6
10
12
PWH M3 x 8
17
18
5 18
17 16
PWH3 x 6
PWH3 x 6
PTP2 x 6
13
1 PWH M3 x 8
PWH
M3 x 8 PWH M3 x 8
6
7
15
4-2 LMD-1420/1410
Overall Block
LMD-1420/1410 4-3
4-3. Electrical Parts List 4-4. Packing Materials & Supplied
Accessories
*1:[LMD-1410]
*2:[LMD-1420] ----------------------------------------
PACKING MATERIALS & SUPPLIED ACCESSORIES
Ref. No. ----------------------------------------
or Q'ty Part No. SP Description Ref. No.
or Q'ty Part No. SP Description
1pc *2 1-789-212-11 s MOUNTED CIRCUIT BOARD, X
1pc *2 1-789-213-11 s MOUNTED CIRCUIT BOARD, Q 1pc 2-581-512-01 s CD-ROM
*1 1-789-229-11 s MOUNTED CIRCUIT BOARD, Q 1pc 2-590-000-01 s MANUAL, INSTRUCTION
1pc 1-789-214-11 s MOUNTED CIRCUIT BOARD, J (JAPANESE,ENGLISH)
1pc *2 1-789-215-11 s MOUNTED CIRCUIT BOARD, H 1pc 2-990-242-01 s HOLDER (B),PLUG
*1 1-789-228-11 s MOUNTED CIRCUIT BOARD, H 1pc ! ------------ CORD, POWER
1pc 1-789-263-11 s MOUNTED CIRCUIT BOARD, BA (See Sec 1-5. Warning on Power Connection)
1pc 1-789-265-11 s MOUNTED CIRCUIT BOARD, S
1pc 1-789-266-11 s MOUNTED CIRCUIT BOARD, GA
4-4 LMD-1420/1410
Overall Overall
Section 5
Block Diagrams
Q BA GA
FLASH
SPEAKER MEMORY POWER
BLOCK
L
AMP+DC
FAN MEMORY
CONTROL 128 x 2 S
SENSOR
YUV422
VIDEO INPUT
PROCESSOR SYNC LDVS NS LCD
RECEIVER LVDS PANEL
L
NTSC
3-DIMENSION
ADG779
DIGITAL
COM FILTER
FOR APL
X
CVBS
YC
FOR NTSC TALLY_G
YC
TALLY_R
KPD[0..6]
TALLY
RX / TX
CVBS
(FOR LMD-1420)
B/Cb
R/Cr
H+V
G/Y
5-INPUT 2-OUTPUT AUDIO/VIDEO SW I2C / VCC
KEY PAD
SP232
CVBS
YC
CVBS
L
L
L
YC
Overall
LMD-1420/1410 5-1 5-1
Frame Wiring Frame Wiring
Section 6
Frame Wiring Diagram
1
J12 J6
J1
1 SENSOR1
SENSOR1 1 GND 1 1 GND
2 2 DUMMY 2
SENSOR2 GND 2 GND
3 SENSOR2 3
RXIN1+ 3 RXIN1+
S LCD_5V
RXIN1_
4
5
4
5
LCD_5V
RXIN1_
LCD_5V 6 6 LCD_5V
GND 7 7 GND
GND
RXIN2+
8
9
8
9
GND
RXIN2+ LCD
RXCLKIN+ 10 10 RXCLKIN+
CN601 CN701 J8
RXIN2_
RXCLKIN_
11
12
11
12
RXIN2_
RXCLKIN_
PANEL
1 N +12V 1 +12V 13
J 2 L +12V
GND
2
3
1
2
3
+12V
GND
GND
GND
RXIN3+
14
15
13
14
15
GND
GND
RXIN3+
GND 4 4 GND RXIN0+ 16 16 RXIN0+
VCC 5 5 VCC RXIN3_ 17 17 RXIN3_ 2
+9V 6 6 +9V RXIN0_ 18 18 RXIN0_
VCC 7 7 VCC GND 19 19 GND
VCC 8 8 VCC GND 20 20 GND
GND 9 9 GND
GND 10 10 GND
NC 11 11 NC
GA GND
LCD_ON
LCD_BR
12
13
14
12
13
14
GND
LCD_ON
LCD_BR
CN702
19V 1 1 19V
INVERTER 19V
GND
2
3
2
3
19V
GND
J1
BOARD LCD_BR 4 4 LCD_BR J2
GND
LCD_ON
GND
5
6
7
5
6
7
GND
LCD_ON
GND BA
GND
R_J2
G_J2
1
2
3
1
2
3
GND
R_J2
G_J2
X
(FOR LMD-1420) 3
J5 J1
INT_I/O 1 1 INT_I/O
GND 2 2 GND
SCL_KEYPAD 3 3 SCL_KEYPAD
SDA_KEYPAD 4 4 SDA_KEYPAD
SPEAKER J27 J1
GND
V33_KEYPAD
5
6
5 GND
6 V33_KEYPAD
J26
1 AUD_OUT+
CVBS_PAL
GND
S_Y
1
2
3
1 CVBS_PAL
2 GND
3 S_Y
V33_KEYPAD 7 7 V33_KEYPAD
H
2 AUD_OUT_
S_C 4 4 S_C
GND 5 5 GND
G_COMP_Y_IN 6 6 G_COMP_Y_IN
R_COMP_CR_IN 7 7 R_COMP_CR_IN
B_COMP_CR_IN 8 8 B_COMP_CR_IN
GND 9 9 GND
EXT_SYNC_IN 10 10 EXT_SYNC_IN J9 FAN1 4
GND 11 11 GND 12V_FAN2 1
SDA_1 12 12 SDA_1 FANSPIN2 2
SCL_1 13 13 SCL_1 GND 3
SYS_MUTE 14 14 SYS_MUTE GND 4
AUD_VOL 15 15 AUD_VOL
Q J24 FAN2
J4 J10
KPD0 1 1 KPD0 12V_FAN1 1
KPD1 2 2 KPD1 FANSPIN1_1 2
KPD2 3 3 KPD2 GND 3
KPD3 4 4 KPD3
KPD4 5 5 KPD4
KPD5 6 6 KPD5
KPD6 7 7 KPD6
GND 8 8 GND
TXD 9 9 TXD J11
FAN3
RX 10 10 RX 12V_FAN1 1 5
GND 11 11 GND FANSPIN1_2 2
SDI_EN 12 12 SDI_EN GND 3
VCC 13 13 VCC
+9V 14 14 +9V
Frame Wiring
LEAKAGE TEST
To Exposed Metal
Parts on Set
AC
0.15 µF 1.5 kZ voltmeter
(0.75V)
Earth Ground
LMD-1420/1410
LMD-1420 (SY) Printed in Japan
LMD-1410 (SY) E Sony Corporation 2005. 3 22
9-968-137-01 B&P Company ©2005