Professional Documents
Culture Documents
1.1. SITE
The equipment subject to this document to be purchased will be lime kiln unit. It is integrated
in SSL. plant area which is located in Lukavac approximately. 12 km away from TUZLA Canton
at Bosnia Herzegovina.
2. SCOPE
2 ( two ) complete set of pump including the motor and auxilarry drive units and all necessary
accessories. Supplier shall also give necessary drawings and/or technical specifications
relevant to the surrounding installations including but not limited to inlet-exit connections,
frames,couplings,lubricating oil, cooling system ( if necessary ), instruments, protective
equipment, .etc.
3. TECHNICAL SPECIFICATIONS
3.1. USAGE
Pump will be installed on the Lime kiln unit and used for transport of milled waste
4. TECHNICAL REQUIREMENTS
The vendor shall assume unit responsibility for all the equipment and all auxilliary systems
included in the scope of the order.
All accesories of the same duty condition and classification, shall be identical and the product
of the same manufacturing source.
In case of a need for parallel-pump operation, pumps selected shall have characteristics
specifically suitable for the service without unstable operation.
All materials shall be suitable for indicated operating conditions and shall be selected corrosion
SSL SISECAM SODA LUKAVAC
Pump seals shall be cartridge type ( packed box ) or have the manufacturer's standard
mechanical seals for the specified service over the fluid defined in this document.
Packing shall be soft woven non-asbestos material with not less than 25 percent by weight of
tetrafluoroethylene resin.
Pump shall be suitable for operation at indicated operating conditions with indicated fluid.
Pump shall be suitable for operation at indicated temperature without vapor binding and without
cavitation under any system operating condition.
Factory Tests
The following tests shall be submitted from the manufacturer prior to shipping the pump from the
factory, hydraulic tests, efficiency tests, vibration tests, output efficiency tests, surface
hardness tests, and shaft deflection tests.
Main dimensions
Static and dynamic loads
Size and position of anchorage bolts.
MECHANICAL
Drawings with a scale of 1:50 showing the main outer dimensions and all connections should
be enclosed to the offer. Last revised drawings of the equipment showing the main outer
dimensions and all connections.
- Material standards used during the manufacturing of the equipment.
- Cross-sectional drawings of mechanical equipment covering identification of spare parts
norms.
- Manufacturing drawings of necessary spare parts.
ELECTRICAL
- Technical characteristic sheets those are belonging to electric motors should be enclosed
to the offer.
INSTRUMENTATION
- P&I diagram showing the type of process control should be enclosed to the offer.
All equipment should be so packed as to provide maximum protection and easy manipulation
and safety transportation with security.
Each packing should be marked as “SSL doo/BiH” and materials contained in each packing
and their weights should be clearly identified on each packing.
All packing charges should be included in the offer.
8. REQUIRED GUARANTEES
Guarantees to be clearly indicated in the offer are given below:
- Guarantee type and period against material and/or manufacturing defaults.
- Supplier should remove any material and/or manufacturing defaults by replacing and/or
repairing free of charge within the shortest time. This period should not exceed one month.
- Supplier should give performance guarantee that the equipment they have offered will
operate at the predetermined capacity, efficiency and accuracy limits and should clearly
indicate the guarantee conditions in their offer.
- Suppier should give a guarantee to supply for each spare part appeared in the spares list
throughout the specified service life. Delivery period of each item should also appear on the
list.
9. PRICE
The equipment to be offered should be priced as for pump and motor separately. Equipment
will be offered as delivered to SSL’s site.
Spare parts recommended for 2 years of operation should be enclosed to the offer separately
each of piece’s price.
Erection, supervision and start-up services should be included in the offer and each be quoted
separately.
10. ASSEMBLY
Assembly and/or installation and commissioning of the equipment shall be done in two
alternatives:
- Either the technical service team of the supplier shall carry out all work except for civil
ones (preparation of foundation, cabling,anchors and mounting base) or,
- SSL (or his subcontractor) shall do it under the supervision of an expert working for the
supplier.
In both cases, at least one expert should be available at SSL site. The expert shall make
necessary inspections prior to commissioning.
11. REFERENCES
Bidders shall provide for their portfolio indicating companies in chemical or mining industries to
which they have already sold similar equipment as reference, if available.
Prepared By
Mersed Đulović