Professional Documents
Culture Documents
PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 30 - 45 minutes
● Tool Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape,
Wire cutter, Safety glasses and (1) 13W CFL Spring self-ballasted GU24 base bulb (supplied) .
● Helpful Tools (not included): Wire strippers.
1 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER: FQ8308MKFL01
STEP 1:
a. Screw the Mounting Screws into the Crossbar, place Mounting Screw
Crossbar
the Lock Washers over the Mounting Screws and
thread the Hex Nuts onto the Mounting Screws as Hex Nut
shown. Secure the position of the Mounting Screws by
tightening the Hex Nuts against the Crossbar.
b. Secure the Crossbar to the Outlet Box with Outlet Box
Screws.
Lock Washer
Outlet Box
Outlet Box Screw
STEP 2:
Use Wire Connectors (not supplied) to connect the
WHITE OR RIBBED WHITE OR RIBBED
wires.
a. Connect the House Ground Wire to the Fixture Ground FROM HOUSE FROM FIXTURE
Wire.
b. Connect the House White (or Ribbed) Wire to the
Fixture Supply Wire (Black or Smooth Side). BLACK (OR RED) WIRE BLACK OR SMOOTH
c. Connect the House Black (or Red) Wire to the Fixture FROM FIXTURE
FROM HOUSE
Supply Wire (Black or Smooth Side).
d. Wrap each connection with approved electrical tape
and carefully stuff all of the connected wires into the GROUND WIRE GROUND WIRE
Outlet Box.
FROM HOUSE FROM FIXTURE
STEP 3:
a. Place the Backplate over the Mounting Screws and
secure with Mounting Balls. Hand-tighten until snug. Mounting Screw
Backplate
Outlet Box
Mounting Ball
2 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER: FQ8308MKFL01
STEP 4:
Lock Screw
a. Locate the Shade inside of the Cage. Attach the Tabs
Tab
onto the top edge of the Shade, line up the holes on
them and the Mounting Holes in the top edge of the
Cage. Using screwdriver, thread the Lock Screws into
the Mounting Holes and hand-tighten until snug to
secure the Shade.
Shade
Mounting Hole
Cage
STEP 5:
a. Install the Bulb (supplied) into the GU24 Base by
aligning the pins on the Bulb with the keyholes in the
GU24 Base. Once they are aligned, gently push the
Bulb into the keyholes and twist the Bulb to lock it in
place.
GU24 Socket
Bulb (supplied)
3 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER: FQ8308MKFL01
STEP 6:
a. Place the Bolts at the top edge of the Cage with Shade
through the holes on the Fixture Hood. Secure by
threading the Mounting Balls onto the Bolts. Hand-
tighten until snug.
Fixture Hood
Mounting Ball
Bolt
STEP 7:
a. Screw the Nipple into the Hex Coupling at the bottom
center of the Cage with Shade. And then thread the
Finial onto the Nipple and hand-tighten until snug.
Cage with Shade
Hex Coupling
Nipple
Finial
4 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER: FQ8308MKFL01
STEP 8:
a. Refer to the following information for caulking instructions:
MOUNTING BALL
With the OUTDOOR FIXTURE properly installed in accordance with supplied Assembly/installation instructions,
proceed with caulking instructions below.
Note: Be sure EXTERIOR WALL SURFACE and FIXTURE BACKPLATE are free to dirt to caulking. Using
EXTERIOR GRADE CAULK, start on one side of FIXTURE BACKPLATE and follow contour, were the FIXTURE
BACKPLATE meets the EXTERIOR WALL SURFACE upward. Proceed to caulk over top of backplate and down
other side. DO NOT CAULK BOTTOM OF FIXTURE BACKPLATE to ensure proper moisture drainage.
EXTERIOR GRADE
CAULK
OUTDOOR
FIXTURE BACKPLATE
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
5 OF 5