Professional Documents
Culture Documents
7 Modem–Transceiver–Branching connections
permitted without written authorization from Alcatel–Lucent
The connections among Modems, Transceivers and Branching depend on the following possible
document, use and communication of its contents not
configurations:
All rights reserved. Passing on and copying of this
INSTALLATION AND TECHNICAL HANDBOOK 9600LSY Rel.1.x & 2.x LHR version
HARDWARE INSTALLATION HANDBOOK
3DB 02839 AAAA Ed.10 163 / 522
a) Without Reuse and without Diversity
N.B. For CABLE TYPE and CABLE SIDE related information, please refer to para.1–10.3 on
page 153.
For the connections between TRANSCEIVER unit and Rx / Tx Branching, refer to documents cited
in para.1–9.7.1 on page 145.
Requirements:
• MODEM does not need any CANC–COMB module (see Fig. 63. on page 120)
9600LSY Rel.1.x & 2.x LHR version INSTALLATION AND TECHNICAL HANDBOOK
HARDWARE INSTALLATION HANDBOOK
164 / 522 3DB 02839 AAAA Ed.10
permitted without written authorization from Alcatel–Lucent
document, use and communication of its contents not
All rights reserved. Passing on and copying of this
MODEM n
G2
J1
BASE BAND SHELF
J2
F2
J3
J4
J5
BRANCHING
RX
J9
TRANSCEIVER SHELF
F1
J10
J11
G1
J5
J6
J14 TRANSCEIVER n
BRANCHING
TX
INSTALLATION AND TECHNICAL HANDBOOK 9600LSY Rel.1.x & 2.x LHR version
HARDWARE INSTALLATION HANDBOOK
3DB 02839 AAAA Ed.10 165 / 522
b) Without Reuse and with Diversity
N.B. For CABLE TYPE and CABLE SIDE related information, please refer to para.1–10.3 on
page 153.
For the connections between TRANSCEIVER unit and Rx / Tx Branching, refer to documents cited
in para.1–9.7.1 on page 145.
Requirements:
• MODEM needs one CANC–COMB module (see Fig. 63. on page 120)
9600LSY Rel.1.x & 2.x LHR version INSTALLATION AND TECHNICAL HANDBOOK
HARDWARE INSTALLATION HANDBOOK
166 / 522 3DB 02839 AAAA Ed.10
permitted without written authorization from Alcatel–Lucent
document, use and communication of its contents not
All rights reserved. Passing on and copying of this
MODEM n
G2
J1
BASE BAND SHELF
J2
F2
J3
H2
J4
J5
BRANCHING
RX
J1 J9
TRANSCEIVER SHELF
H1 F1
J2 J10
J3 J11
G1
J5
J6
TRANSCEIVER n
J14
BRANCHING
TX
INSTALLATION AND TECHNICAL HANDBOOK 9600LSY Rel.1.x & 2.x LHR version
HARDWARE INSTALLATION HANDBOOK
3DB 02839 AAAA Ed.10 167 / 522
c) With Reuse and without Diversity
N.B. For CABLE TYPE and CABLE SIDE related information, please refer to para.1–10.3 on
page 153.
The connections must be done between two contiguous pairs of channels, i.e.:
• (MODEM 0 + TRANSCEIVER 0) connected to (MODEM 1 + TRANSCEIVER 1)
• (MODEM 2 + TRANSCEIVER 2) connected to (MODEM 3 + TRANSCEIVER 3)
• ....
• (MODEM 8 + TRANSCEIVER 8) connected to (MODEM 9 + TRANSCEIVER 9)
For the connections between TRANSCEIVER unit and Rx / Tx Branching, refer to documents cited
in para.1–9.7.1 on page 145.
Requirements:
• both MODEMs need one CANC–COMB module (see Fig. 63. on page 120)
• TRANSCEIVER ASSEMBLY TYPE (see Tab. 19. on page 129 ) and Rx Local Oscillator
MASTER/SLAVE configuration (see para.1–9.6.6 on page 140 ) : the two transceivers must be
configured differently from each other:
hardware setting: the Rx Local Oscillator hardware setting: the Rx Local Oscillator
must be configured as “MASTER” must be configured as “SLAVE”
WARNING: in Frequency Reuse systems with Transceiver and Modem units powered on,
whenever you must disconnect the cable N1–N2 shown in Fig. 93. on page 169 (e.g.
for troubleshooting), it is mandatory to disconnect before the cable K1 (slave TR ) –
K2 (master TR). This caution is not necessary in the unit replacement procedures of
para.4–7.4 from page 328 , because they envisage the Transceiver or Modem unit
switch off, before the cable remotion.
9600LSY Rel.1.x & 2.x LHR version INSTALLATION AND TECHNICAL HANDBOOK
HARDWARE INSTALLATION HANDBOOK
168 / 522 3DB 02839 AAAA Ed.10
permitted without written authorization from Alcatel–Lucent
document, use and communication of its contents not
All rights reserved. Passing on and copying of this
J2 J2
F2 F2
J3 J3
K2 K2
J4 J4
J5 J5
BRANCHING
RX
J9 J9
TRANSCEIVER SHELF
F1 F1
TRANSCEIVER V (H)
J10
TRANSCEIVER H (V)
J10
K1 K1
J11 J11
G1 G1
J5 J5
N1 N2
J6 J6
J14 J14
BRANCHING
TX
INSTALLATION AND TECHNICAL HANDBOOK 9600LSY Rel.1.x & 2.x LHR version
HARDWARE INSTALLATION HANDBOOK
3DB 02839 AAAA Ed.10 169 / 522
d) With Reuse and with Diversity
N.B. For CABLE TYPE and CABLE SIDE related information, please refer to para.1–10.3 on
page 153.
The connections must be done between two contiguous pairs of channels, i.e.:
• (MODEM 0 + TRANSCEIVER 0) connected to (MODEM 1 + TRANSCEIVER 1)
• (MODEM 2 + TRANSCEIVER 2) connected to (MODEM 3 + TRANSCEIVER 3)
• ....
• (MODEM 8 + TRANSCEIVER 8) connected to (MODEM 9 + TRANSCEIVER 9)
For the connections between TRANSCEIVER unit and Rx / Tx Branching, refer to documents cited
in para.1–9.7.1 on page 145.
Requirements:
• both MODEMs need two CANC–COMB modules (see Fig. 63. on page 120)
• TRANSCEIVER ASSEMBLY TYPE (see Tab. 19. on page 129 ) and Rx Local Oscillator
MASTER/SLAVE configuration (see para.1–9.6.6 on page 140 ) : the two transceivers must be
configured differently from each other:
hardware setting: the Rx Local Oscillator hardware setting: the Rx Local Oscillator
must be configured as “MASTER” must be configured as “SLAVE”
WARNING: in Frequency Reuse systems with Transceiver and Modem units powered on,
whenever you must disconnect the cable N1–N2 shown in Fig. 94. on page 171 (e.g.
for troubleshooting), it is mandatory to disconnect before the cable P1 (slave TR ) –
P2 (master TR). This caution is not necessary in the unit replacement procedures of
para.4–7.4 from page 328 , because they envisage the Transceiver or Modem unit
switch off, before the cable remotion.
9600LSY Rel.1.x & 2.x LHR version INSTALLATION AND TECHNICAL HANDBOOK
HARDWARE INSTALLATION HANDBOOK
170 / 522 3DB 02839 AAAA Ed.10
permitted without written authorization from Alcatel–Lucent
document, use and communication of its contents not
All rights reserved. Passing on and copying of this
G2 G2
J1 J1
BASE BAND SHELF
J2 J2
F2 F2
J3 J3
H2 H2
J4 J4
P2 P2
J5 J5
BRANCHING
RX
J1 J9 J1 J9
F1 H1
TRANSCEIVER SHELF
F1
TRANSCEIVER V (H)
J2 J10
TRANSCEIVER H (V)
J2 J10
H1
J11
P1
J3 J3 J11
P1
G1 G1
J5 J5
N1 N2
J6 J6
J14 J14
BRANCHING
TX
INSTALLATION AND TECHNICAL HANDBOOK 9600LSY Rel.1.x & 2.x LHR version
HARDWARE INSTALLATION HANDBOOK
3DB 02839 AAAA Ed.10 171 / 522