You are on page 1of 14

Internal Use Only▲

DOCUMENT

FOR

Data Transfer Using Peer to Peer


Connectivity with CDMA FWT

Prepared By,
Adnan Buland Khan
MSS Engineer
Gwalior MSC

No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any
means without the prior written permission of ZTE Corporation page 1 total 14
Internal Use Only▲

All we have to do is to arrange two FWT’s (Here we had used Hantel).


Then we have done Programming in both FWT.

1. Go to menu.
2. Press 0.
3. Select 3rd option (Rx data mode).
4. In Rx data mode – Select” Modem until off”.
5. Come back to Menu.
6. Press 0.
7. Select 4th option (SIO).
8. In “SIO” Select “PORT MAP”.
9. In “Port Map” select “USB DIAG”.
10. Then Power off and power on handset.

Sender Number = 07522280002


Receiver Number = 07512050002

Connect both FWT’s to two different PC with Cables & Install the USB Driver of Hantel.

USB_driver.rar

No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any
means without the prior written permission of ZTE Corporation page 2 total 14
Internal Use Only▲

After connecting FWT with PC Open Hyper-terminal Programme:

Enter details for the calling number that we want to dial:

No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any
means without the prior written permission of ZTE Corporation page 3 total 14
Internal Use Only▲

Dial the number

Dialing is going on as shown in below picture.

No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any
means without the prior written permission of ZTE Corporation page 4 total 14
Internal Use Only▲

After dialing connection established and then we transfer the Data.

Browse the file and send

No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any
means without the prior written permission of ZTE Corporation page 5 total 14
Internal Use Only▲

File transfer is going on…

File transferred.

Note: Operation Above is carried out on the Calling party Number, to send the data on
the called number.

No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any
means without the prior written permission of ZTE Corporation page 6 total 14
Internal Use Only▲

Receiver’s end PC….. We open “hyper-terminal”

Enter details for the phone number that you want to DIAL:

No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any
means without the prior written permission of ZTE Corporation page 7 total 14
Internal Use Only▲

Then we click the Cancel option. No need to Dial… Just wait for the call from Calling
Number.

Then we see blank windows of Hyper-terminal

No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any
means without the prior written permission of ZTE Corporation page 8 total 14
Internal Use Only▲

Now put command and hit the ENTER key from keyboard.

Now put command and hit the ENTER key from keyboard.

No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any
means without the prior written permission of ZTE Corporation page 9 total 14
Internal Use Only▲

Now put command and hit the ENTER key from keyboard.

Now put command and hit the ENTER key from keyboard.

No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any
means without the prior written permission of ZTE Corporation page 10 total 14
Internal Use Only▲

Now put command and hit the ENTER key from keyboard.

Now we are ready for receiving data call.

No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any
means without the prior written permission of ZTE Corporation page 11 total 14
Internal Use Only▲

Ring is coming from 07522280002 as shown below:

Now the data call is connected.

No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any
means without the prior written permission of ZTE Corporation page 12 total 14
Internal Use Only▲
Now the data is coming

Place where our data will come

No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any
means without the prior written permission of ZTE Corporation page 13 total 14
Internal Use Only▲

Data received:

Test completed

No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any
means without the prior written permission of ZTE Corporation page 14 total 14

You might also like