Professional Documents
Culture Documents
Patm
H
Hg
h
H
16 For a given heat flow and for the same thickness, the temperature drop across the
material will be maximum for
(a) copper (b) steel (c) glass wool (d) refractory brick
OR
Temperature variation under steady state conduction across a composite slab of
two materials with thermal conducting K1 & K2 is shown in the figure. Which of
the following is correct?
(a) K1 > K2 (b) K1 = K2 (c) K1 < K2 (d) K2≈ 0
Mahindra & Mahindra Ltd., Auto Sector.
Graduate Engineer Trainee: Written Test
Heat Flow
K1
K2
18 As the temperature of the intake air increases, the effeciency of the IC engine
improves, but the efficiency of the air compressor falls down. This statement is
(a) false (b) true (c) depends on the type of compressor
(d) can’t say
19 A free bar of length L is uniformly heated from zero deg C to t deg C. If a is the
coefficient of linear expansion and E the modules of elasticity, the stress in the
bar will be
(a) atE (b) atE/2 (c) zero (d) infinite
21 An engine receives 15000 J/S heat and produces 5kW of power. Its efficiency is
(a) 33% (b) 20% (c) 100% (d) 66%
25 Two shafts A & B have their diameters specified as 100 ± 0.1 mm and 0.1 ±
0.0001 mm respectively. Which of the following statements is/are true
(a) Tolerance in the dimension is greater in shaft A
(b) The relative error in the dimension is greater in shaft A
(c) Tolerance in the dimension is greater in shaft B
(d) Shaft A is smoother than shaft B
28 __________ of the material should be taken as criterion for shaft design under
dynamic stress
(a) elastic limit (b) yield trength (c) Poisson’s ratio (d) endurance limit
31 A test specimen is stressed slightly beyond the yield point and then unloaded. Its
yield strength will
(a) decrease (b) increase (c) remain unchanged (d) become equal to UTS
33 The correct Bending Moment diagram of the cantilever beam loaded as shown in
the figure below will be
w/m
A.
36 A block of steel is acted upon by a tangential force on its top surface while the
Mahindra & Mahindra Ltd., Auto Sector.
Graduate Engineer Trainee: Written Test
surface is held rigidly. The deformation of the block is due to
(a) shear only F
(b) bending only
(c) shear & bending
(d) torsion
37 The number of degrees of freedom of a five-link plane mechanism with five
revolute pairs (see figure below) is
4 3
2
5 1
B
O
A
44 A body cools from 60 to 52 deg C in 5 minutes. All other conditions remaining the
same, this body will take _____ minutes to cool from 52 to 44 deg C
(a) 5 (b) more than 5 (c) less than 5 (d) this is an ill-posed problem
46 Heat transfer coefficients for (I) free convection in gases, (ii) forced convection in
gases (iii) forced convection in liquids, (iv) boiling water will have the following
ascending order
(a) i, ii, iii, iv (b) ii, i, iii, iv (c) iv, iii, ii, i (d) iii, iv, i, ii
49 A box with a square base and open top is to have a volume of 32 cc. Find its
dimensions if it is to be made with minimum area of material.
50 On the psychrometric chart, consider a point at a given drg and wet bulb
temperature. At this point, show directions of
d
c
(a) sensible cooling
(b) sensible heating
a
(c) adiabatic saturation o b
(d) isothermal humidificaiton w
(e) cooling & dehumidificaiton e
t
Mahindra & Mahindra Ltd., Auto Sector.
Graduate Engineer Trainee: Written Test
51 A 4-cyld 4-stroke SI engine develops a max brake torque of 160 N-m at 3000 rpm.
Estimate the bore size. The brake mep at the max engine torque point is 960 kPa.
Assume bore is equal to stroke.
52 A circular disc of mass 10 kg and radius 0.2 m is rotated about an axis (passing
through its center and perpendicular to its plane) by a torque of 10 N-m. Calculate
the angular velocity of the disc at the end of 6 seconds from start.
53 A single block brake with a 300 mm dia brake drum (see fig below) is used to absorb
a torque of 75N-m. Co-efficiency of friction between the drum and the lining is 0-35.
The pressure on the block is uniform. Estimate the force P.
250 mm P
200 mm *
50
300 dia