Professional Documents
Culture Documents
RP Heads
53
Accuracy
Versatility
Accuracy completely independent of pulse rate, duration or history. Built-in wavelength correction.
Measurements of very long and very short pulses (e.g. excimer and holmium) with same head. Nova, Nova II and Laserstar displays with Smart Connector, compatible with all Ophir Thermopile and Photodiode heads. Measurement from nW to KW, J to 200J with appropriate heads Nova and Laserstar displays show average power, frequency, average energy, exposure, energy bar graph and more. Nova II and Laserstar displays allow on-board storage and transmission of every pulse to >1500Hz.
Performance Pulse rate to 5000Hz (PE10). Energy measurement to 10pJ (PD10-pJ). High damage threshold. Diffuser models for high energy YAG / Holmuim / Erbium lasers. Diffuser is removable. Metallic and broadband coatings. Wide dynamic range.
RP Heads
The use of Ophir RP (Repetitive Pulse) models together with the Laserstar display allows you to measure energy of repetitively pulsed lasers with a high degree of accuracy. The innovative principle of the RP (patented) combines highly accurate measurement of average power using a thermal head, with measurements of relative pulse energy using a photodiode that provides the energy per pulse. This innovation allows RP to measure powers and energies only a thermal head is able to measure with measurement of repetitive pulse energy. You can also measure at repetition rates never before available. The RP also gives you a wealth of information about your laser. Along with pulse energy it provides data about average power, frequency, minimum and maximum values, missing pulses, time jitter and standard deviation. The display of pulse energies can be either numerical or in graphs. Up to 50,000 points, of data can be stored on-board in nonvolatile memory and can be sent either offline or online to PC. The RP heads have a separate fast photodiode to measure temporal pulse shape. When the BNC output is connected to a fast scope, the pulse shape is displayed with ns resolution. The RP also does everything a standard Ophir thermal head can do such as power measurement, single shot energy and laser power tuning.
54
Pyroelectric and Photodiode Heads for Repetitive Pulses Photodiode Heads PD10
Pulse Energy Measurements 1nJ to 20J, up to 10,000Hz
Recommended Use: Measurement of low energies and high repetition rates Special Features: Energies down to nanojoules and frequencies up to 10KHz
Spectral Response: Surface reflectivity: Aperture: Energy Scales: Lowest Measurable Energy: Noise on Lowest Range: Maximum Pulse Width: Additional Error with Frequency: Maximum Average Power: Maximum Average Power Density: Maximum Energy vs. Wavelength Silicon Photodiode, 0.19 - 1.1m 50% approx. 10mm 20J/2J/200nJ/20nJ 2nJ at 900nm 0.2nJ 5s 1% to 10000Hz 50mW at 800nm 50W/cm Wavelength Maximum Energy <300nm 15J 350 - 550nm 8J >800nm 5J 0.1J/cm 5% Additional Error Wavelength 3% 193nm, 200-250nm 0 250-950nm 2% 950-1100nm 1% for > 10% of full scale PD10
Linearity:
PD10-pJ
Pulse Energy Measurements 10pJ to 200nJ, up to 10,000Hz
Recommended Use: Measurement of extremely low energies and high repetition rates Special Features: Energies down to picojoules frequencies up to 10KHz
Spectral Response: Surface Reflectivity: Aperture: Energy Scales: Lowest Measurable Energy: Noise on Lowest Range: Maximum Pulse Width: Additional Error with Frequency: Maximum Average Power: Maximum Average Power Density: Maximum Energy vs. Wavelength Silicon Photodiode, 0.2 - 1.1m 30% approx. 10mm 200nJ/20nJ/2nJ/200pJ 10pJ at 900nm 2pJ 5s 1% to 10000Hz 0.5mW 5W/cm Wavelength Maximum Energy <300nm 150nJ 350-550nm 75nJ >800nm 50nJ 0.1J/cm 5% Additional Error Wavelength 2% 200-250nm 0 250-950nm 2% 950-1100nm 1% for > 10% of full scale
NEW
PD10-pJ
Linearity:
Ordering information Description Photodiode energy meter for up to 15J and 10KHz Photodiode energy meter for up to 200nJ and 10KHz
55
PE9 PE9-F 15s 0.5s 4KHz 20KHz 2.5% to 3KHz, 8% to 4KHz 2% error to 20kHz <0.2J 0.3J Operates with all Ophir smart Operates only with Nova II displays Laserstar and USB Interface Metallic absorber 0.19-12m 50% approx 1mJ, 200J, 20J, 2J 30nJ 3% 10% 0 4% 0 0 8% 15% 0.1J/cm 0.2J/cm 8mm 2W 50W/cm 1% 10nJ for >10% of full scale a Convection
NEW
PE9
a. For PE9-F on lowest scale, offset can reach - 100nJ for frequencies below 5KHz
Ordering information Description Pyroelectric energy meter for very low energies 0.2J to 1mJ, 4KHz, metallic absorber. Pyroelectric energy meter for very low energies 0.3J to 1mJ, 20KHz, metallic absorber. Operates with Nova II, Laserstar and USB Interface only.
56
PE10 / PE10BB
Pulse Energy Measurements 2J - 10mJ, up to 4000Hz
Recommended Use: High and low repetition rate pulse measurement of low energy lasers Special Features: Very low energies
Specifications PE10 PE10BB Spectral Response: Metallic absorber 0.15 - 12m Black absorber 0.15 - 20m Surface Reflectivity: 50% approx. 5% approx. Maximum Pulse Width: 20s 500s Maximum Pulse Rate: 4000Hz 150Hz Energy Scales: 10mJ / 2mJ / 200J / 20J 10mJ / 1mJ / 100J Lowest Measurable Energy: 2J 10J Noise on Lowest Range: 0.3J 2.5J Additional Error with 1.5% to 3KHz,3% to 4KHz 1.5% to 150Hz Frequency: Calibration Accuracy: 3% 3% Additional Error with Wavelength: 157nm 10% 193nm 0 2% 240-800nm 4% 2% 1064nm 0 0 2-3m 8% 2% 10.6m 15% 5% Damage Threshold: <100ns 0.1J/cm 0.3J/cm 1s 0.2J/cm 0.3J/cm 300s 3J/cm 1J/cm Aperture: 12mm Maximum Average Power: 2W Maximum Average Power Density: 50W/cm Linearity: 2% for >10% of full scale Cooling: Convection
PE10
Ordering information Description Pyroelecric energy meter for low energies 2J to 10mJ. Spectral range 0.19 - 12m PE10 with broadband spectrally flat absorber
57
PE25/PE25BB/PE25BBH
Pulse Energy Measurements 15J - 10J, up to 5000Hz
Recommended Use: General use for medium aperture pulsed lasers to 10ms and 5000Hz Special Features: PE25: High repetition rate, high sensitivity PE25BB: Spectrally flat, high damage threshold PE25BBH: Spectrally flat, low reflection, high repetition rate
Specifications Spectral Response: Surface Reflectivity: Max Pulse Width Setting: Maximum Pulse Width: Maximum Pulse Rate: Energy Scales: Lowest Measurable Energy: Noise on Lowest Range: Additional Error with Frequency: Calibration Accuracy: Additional Error with Wavelength: 157nm 193nm 248nm 355nm 300-800nm 1064m 1.5-2m 2.94m 10.6m Damage Threshold: <100ns 1s 300s 2ms Linearity: Aperture: Maximum Average Power: Maximum Average Power Density: Cooling:
Notes:
PE25 Metallic absorber 0.15 - 3m 50% approx. Short Long 30s 1ms 5000Hz 250Hz 10J to 200J 10J to 2mJ 15J 70J 0.8J 2J 2% to 5KHz 1% 3% 5% 2% 0 0 2% 0 2% 0 N.A. 0.1J/cm 0.2J/cm 2J/cm 6J/cm 2% for >10% of full scale a 24 x 24mm 10W 10W/cm Convection
PE25BB Black absorber 0.15 - 20m 5% approx. Short Long 3ms 10ms 40Hz 12Hz 10J to 2mJ 10J to 20mJ 100J 1mJ 20J 100J 1% 2% 3% N.A. 2% 2% 2% 2% 0 2% 2% 5% 0.3J/cm 0.3J/cm 1J/cm 2J/cm 2% for >10% of full scale
PE25BBH High speed black absorber 0.15 - 1.7m, 10.6m 5% approx. Short Long 50s 1ms b 1400Hz 200Hz 10J to 200J 10J to 2mJ 20J 100J 1J 4J 2% 1% 3% 5% 2% 0 1% 2% 0 2% N.A. 5% 0.2J/cm 0.3J/cm 2J/cm 6J/cm 2% for >10% of full scale
PE25/PE25BB/ PE25BBH
Ordering Information Description 24x24mm aparture pyroelectric energy meter with metallic absorber 24x24mm aperture pyroelectric energy meter with broadband absorber 24x24mm aperture pyroelectric energy meter with high rep rate spectrally flat black absorber
58
PE50/PE50BB/PE50BBH
Pulse Energy Measurements 25J to 10J, up to 4000Hz
Recommended Use: General for large aperture pulsed lasers to 10ms and 4000Hz Special Features: PE 50: High repetition rate, high sensitivity PE 50BB: Spectrally flat, high damage threshold very long pulses PE 50BBH: Spectrally flat, 10W reflection, high repetition rate
Specifications PE50 Metallic absorber Spectral Response: 0.15 - 3m Surface Reflectivity: 50% approx. Max Pulse Width Setting: Short Long Maximum Pulse Width: 30s 1ms Maximum Pulse Rate: 4000Hz 250Hz Energy Scales: 10J to 200J 10J to 2mJ Lowest Measurable Energy: 25J 80J Noise on Lowest Range: 2J 8J Additional Error with 2% 1% Frequency: Calibration Accuracy: 3% Additional Error with Wavelength: 157nm 5% 193nm 2% 248nm 0 355nm 0 300-800nm 2% 1064nm 0 1.5-2m 2% 2.94m 0 10.6m N.A. Damage Threshold: <100ns 0.1J/cm 1s 0.2J/cm 300s 2J/cm 2ms 6J/cm Linearity: 2% for >10% of full scale Maximum Average Power: 20W Aperture: Maximum Average Power Density: Cooling:
Notes:
PE50BB Black absorber 0.15 - 20m 5% approx. Short Long 3ms 10ms 40Hz 10Hz 10J to 2mJ 10J to 20mJ 100J 1mJ 15J 40J 1% 3% 1%
PE50BBH High speed black absorber 0.15 - 1.7m, 10.6m 5% approx. Short Long 50s 1ms a 1000Hz 150Hz 10J to 200J 10J to 2mJ 20J 100J 2J 10J 1.5% 3% 1% PE50/PE50BB/PE50BBH
N.A. 2% 2% 2% 2% 0 2% 2% 5%
5% 2% 0 1% 2% 0 2% N.A. 5%
0.3J/cm 0.2J/cm 0.3J/cm 0.3J/cm 1J/cm 2J/cm 2J/cm 6J/cm 2% for >10% of full scale 2% for >10% of full scale 15W 15W 46mm 10W/cm Convection
a. 3% lower reading at pulse width >500s. PE50BBH-L version available with pulse widths up to 10ms
Ordering information Description 46mm aperture pyroelectric energy meter with metallic absorber 46mm aperture pyroelectric energy meter with broadband absorber 46mm aperture pyroelectric energy meter with high rep rate spectrally flat black absorber 46mm aperture pyroelectric energy meter with spectrally flat black absorber for pulse widths up to 10ms KF40 Vacuum flange to replace PE50 front flange. Fits PE50 to vacuum system for measuring vacuum UV 157nm radiation
59
PE25BB-DIF/PE25-DIF
Pulse Energy Measurements 50J to 20J, up to 2500Hz
Recommended Use: PE25BB-DIF: High evergy YAG lasers, general PE25-DIF: High rep rate high energy lasers Special Features: Diffuser for high damage threshold
Specifications Aperture: Spectral Response: Surface Reflectivity: Calibration Accuracy: Additional Error with Wavelength: 193nm 248nm 400-800nm 1064nm 1.5-2.5m 2.1m 10.6m Damage Threshold: <100ns 1s 300s Linearity: Maximum Average Power: Max Ave Power Density: Max Pulse Width Setting: Maximum Pulse Width: Maximum Pulse Rate: Energy Scales: Lowest Measurable Energy: Noise on Lowest Range: Additional Error with Frequency: Cooling Convection
Notes:
PE25BB-DIF Diffuser out 24x24mm 0.15 20m 5% approx. 3% 2% 2% 2% 0 -4% (See note c) -4% (See note c) 5% (See note c) 0.3J/cm 0.3J/cm 1J/cm 2% for>10% of full scale 10W 10W/cm Short Long 3ms 12ms 40Hz 10Hz 10J to 2mJ 10J to 20mJ 50J 500J 5J 20J 1% 2%
Diffuser in 20mm 0.4 2.5m 15% approx. 3% N.A. N.A. See note a 0 See note b 0 N.A. 1.5J/cm 2J/cm 10J/cm 2% for >10% of full scale 30W 300W/cm Short Long 3ms 12ms 40Hz 10Hz 20J to 4mJ 20J to 40mJ 200J 1mJ 10J 50J 1.5% 1.5%
PE25-DIF Diffuser in only 20mm 0.4 2.5m 15% approx. 3% N.A. N.A. See note a 0 See note b N.A. N.A. 1.5J/cm 3J/cm 30J/cm 2% for >10% of full scale 30W 300W/cm Short Long 50s 1ms 2500Hz 250Hz 20J to 4mJ 20J to 4mJ 150J 200J 10J 10J 1.5% 1%
a. Calibrated for 532nm b. With diffuser installed, head is not calibrated at these wavelengths but provision is made for user calibration c. When set to 106 setting
PE25BB-DIF
PE25-DIF
Ordering information Description 24x24mm/20mm aperture pyroelectric energy meter with broadband absorber and removable diffuser 20mm aperture pyroelectric energy meter with fixed diffuser for high rep rates.
60
PE50BB-DIF/PE50DIF-ER
Pulse Energy Measurements 60J to 40J, up to 400Hz
Recommended Use: PE50BB-DIF: High energy YAG lasers, general PE50DIF-ER: High rep rate high energy lasers, Erbium lasers Special Features: Removable diffuser for high damage threshold
Specifications Aperture: Spectral Response: Surface Reflectivity: Calibration Accuracy: Additional Error with Wavelength: 193nm 248nm 400-800nm 1064nm 1.5-2.5m 2.1m, 2.94m 10.6m Damage Threshold: <100ns 1s 300s Linearity: Maximum Average Power: Max Ave Power Density: Max Pulse Width Setting: Maximum Pulse Width: Maximum Pulse Rate: Energy Scales: Lowest Measurable Energy: Noise on Lowest Range: Additional Error with Frequency: Cooling Convection
Notes:
PE50BB-DIF Diffuser out 46mm 0.19 - 20m 5% 3% 2% 2% 2% 0 2% 2% 5% 0.3J/cm 0.3J/cm 1J/cm 2% for>10% of full scale 15W 10W/cm Short 3ms 40Hz 10J to 2mJ 100J 15J 1%
Diffuser in 33mm 0.4 - 2.5m 15% 3% N.A. N.A. See note a 0 See note b N.A. N.A. 3J/cm 3J/cm 10J/cm 2% for >10% of full scale 40W 500W/cm Short 3ms 40Hz 40J to 8mJ 500J 80J 1%
PE50DIF-ER Diffuser out 46mm 0.19 - 3m 50% 3% N.A. 0 2% 0 N.A. N.A. N.A. 0.1J/cm 0.2J/cm 4J/cm 2% for >10% of full scale 20W 10W/cm Short 200s 400Hz 10J to 2mJ 60J 5J 1%
Diffuser in 33mm 0.4 - 3m 15% 3% N.A. N.A. See note b 0 See note b 0 N.A. 1.5J/cm 3J/cm 40J/cm 2% for >10% of full scale 40W 500W/cm Short Long 200s 1ms 400Hz 200Hz 30J to 6mJ 30J to 6mJ 300J 0.5mJ 30J 50J 1% 1%
a: Calibrated for 532nm b: With diffuser installed, head is not calibrated at these wavelengths but provision is made for user calibration
PE50BB-DIF/PE50DIF-ER
DIFFUSER in
DIFFUSER out
Ordering information Description 33/46mm aperture pyroelectric energy meter with broadband absorber and removable diffuser 33/46mm aperture pyroelectric energy meter with metallic absorber and removable diffuser
61
PE50-DIF-U
Pulse Energy Measurements 40J to 10J, up to 3000Hz
Recommended Use: High energy excimer lasers in the UV Special Features: High damage threshold and high repetition rate Millions of pulses with no change in calibration
Spectral Response: Surface reflectivity: Maximum Pulse Width: Maximum Pulse Rate: Energy Scales: Lowest Measurable Energy: Noise on Lowest Range: Additional Error with Frequency: Calibration Accuracy: Additional Error with Wavelength: 193nm 248nm 308nm 351nm Damage Threshold for <100ns pulses: Linearity: Maximum Average Power: Aperture: Maximum Average Power Density: Uniformity over the Surface: Change in Calibration with Dose: Cooling: 0.19 - 0.4m 15% approx. 30s 3000Hz 10J / 2J / 200mJ / 20mJ / 2mJ / 200J 30J 1.5J 1% 3% 0 0 3% 2% >300mJ/cm 2% for >10% of full scale 20W 33mm 25W/cm 2% 1% change with 150,000J/cm Convection
PE50-DIF-U
PE50HD
Pulse Energy Measurements 1mJ to 10J, up to 100Hz
Recommended Use: High energy excimer lasers at 193nm Special Features: High damage threshold for 193nm radiation
Spectral Response: Surface Reflectivity: Maximum Pulse Width: Maximum Pulse Rate: Energy scales: Lowest Measurable Energy: Noise on Lowest Range: Additional Error with Frequency Calibration Accuracy: Damage Threshold: Linearity: Maximum Average Power: Aperture: Maximum Average Power Density: Uniformity over Surface Cooling:
Note: Note:
HD type for 157nm 12m, calibrated at 193nm ~10% in the UV 1ms a 100Hz 10J/1J/100mJ/10mJ 0.5mJ 20J 1% 3% at 193nm 1J/cm b 2% for >10% of full scale 15W 46mm 10W/cm 3% over 80% of area Convection
PE50HD
a. Linearity with pulse width: 1% 0 - 400s, 4% at 1ms b. At energy densities above 0.5J/cm reading may be lower with no permanent damage.
Ordering information Description 33mm aperture pyroelectric head with high damage threshold and high repetition rate for UV lasers 46mm aperture pyroelectirc head with very high damage threshold absorber for 193nm
62
Beam Splitter: Aperture: Maximum Energy Density on window J/cm2 for single or repetitive pulses: Fraction split off by beam splitter at 45o:
UV grade fused silica. Spectral range 0.19-3m 60mm pulse width 10ns >300s damage threshold 5J/cm2 >200J/cm2
4% to 9% depending on wavelength
Ordering Information Item Description Beam Splitter Beam Splitter for PE and thermal heads Replacement window for Beam Splitter
63
SCOPE ADAPTER
FIBER ADAPTER
TEST SLIDES
Description Plugs in between the PE head and display. Provides BNC output to scope to see every pulse up to the maximum frequency of the head. PE Metallic Test Plate - set of 3 Damage threshold test plate for metallic coating PE heads PE BB Test Plate - set of 3 Damage threshold test plate for BB coating PE heads PE BBH Test Plate - set of 3 Damage threshold test plate for BBH coating PE heads Ferrite choke Ferrite choke to install on head cable near head to reduce electromagnetic interference in situations of high EMI
Fiber Adapters
Mounting fiber optics to your pyroelectric heads requires an adapter bracket then the fiber optic adapter for the type of fiber used. The information below also shows the distance from the fiber tip to the absorber or diffuser surface. Ordering Information for Fiber Adapter Mounting Bracket (Each bracket can be used for all adapters below) Head P/N Bracket P/N Distance from fiber to detector surface 1Z02823 1Z08236 10mm 1Z02824 1Z08236 10mm 1Z02877 1Z08231 10mm 1Z02862 1Z08236 10mm 1Z02861 1Z08231 10mm 1Z02865 1Z08231 10mm 1Z02860 1Z08232 15mm 1Z02864 1Z08232 15mm 1Z02866 1Z08232 15mm 1Z02867 1Z08232 15mm
PE head typePD10-V2 PD10-pJ-V2 PE9 PE10-V2 PE25-V2 PE25BB-V2 PE50-V2 PE50BB-V2 PE50BB-DIF-V2 PE50DIF-ER-V2
Ordering Information for Fiber Adapters LC Fiber Adapter ST Fiber Adapter FC Fiber Adapter 1Z08228 1Z08226 1Z08229
RP Heads 30A-P-RP
CW & Single Pulse Measurements 30mW - 30W up to 15000Hz pulse rate, up to 200ms pulse width
Recommended Use: Q switched and general pulsed lasers Special Features: 30W average power, temporal pulse shape
Absorber: Spectral Range for Power: Spectral Range for Energy: Aperture: Digital Power Scales: Maximum Average Power Density: Power Noise Level: Power Accuracy: Stabilization Time: Energy Scales: Energy Accuracy: Minimum Energy: Minimum Average Power: Maximum Pulse Width: Maximum Energy Density and Repetition Rate: P type 0.19 - 6m 0.19 - 1.1m 17mm 30W/3W 50W/cm 3mW 3% 6s 3J to 30mJ 5% for energies >30% of full scale 50J in repetitive mode, 30mJ in single shot mode 30mW 200ms Pulse width J/cm Max Rep Rate <10s 1 15KHz 0.5ms 1 1.4KHz 5ms 1 150Hz 100ms 1 7Hz 6ns 0.5V for 10MW peak power at 1064nm 30A-P-RP
System/Display Specifications when used with Laserstar Display Function Specification Frequency Measurement Accuracy: 0.01% Statistics Displayed: Min, Max, Std Dev, Jitter, Missing points Data Memory Capacity (nonvolatile): 50,000 points Computer Interface: RS232 Standard, GPIB Optional Maximum Data Acquisition Rate: Sample to 15KHz, every pulse to 280 Hz Max. Real Time Data Transfer to PC: 100Hz with GPIB
Item 30A-P-RP
Ordering information Description RP power/energy meter for powers to 30W, energies to 3J and rep rates to 15,000Hz
65
FL250A- RP
CW & Single Pulse Measurements 100mW - 250W, up to 15000Hz pulse rate, up to 200ms pulse width
Recommended Use: Large aperture pulsed lasers Special Features: 250W average power, temporal pulse shape
Absorber: Spectral Range for Power: Spectral Range for Energy: Aperture: Digital Power Scales: Maximum Average Power Density: Power Noise Level: Power Accuracy: Stabilization Time: Energy Scales: Energy Accuracy: Minimum Energy: Minimum Average Power: Maximum Pulse Width: Maximum Energy Density and Repetition Rate: Broadband 0.19 - 6m 0.19 - 1.1m 50mm 250W / 30W 8KW/cm 10mW 3% 6s 100J to 3mJ 5% for energies >30% of full scale 100J in repetitive mode, 50mJ in single shot mode 100mW 200ms Pulse width J/cm Max Rep Rate <10s 0.3 15KHz 0.5ms 5 1.4KHz 5ms 20 150Hz 100ms 400 7Hz 1s ~0.2V for 10MW peak power at 248nm Fan
FL250A-RP
Pulse Shape Photodiode Response Time: Approximate peak voltage into 50 Cooling:
System/Display Specifications when used with Laserstar Display Function Specification Frequency Measurement Accuracy: 0.01% Statistics Displayed: Min, Max, Std Dev Data Memory Capacity (nonvolatile): 50,000 points Computer Interface: RS232 Standard, GPIB Optional Maximum Data Acquisition Rate: Sample to 15KHz, every pulse to 280 Hz Max. Real Time Data Transfer to PC: 100Hz with GPIB
Item FL205A-RP
Ordering information Description RP power/energy meter for powers to 250W, energies to 100J and large apertures. For spectral range 0.19-1.1m. Good for diode lasers and metal vapor lasers.
66
L1500W-LP-RP
CW & Pulse Measurements 10W - 1500W, up to 1500Hz pulse rate, up to 200 ms pulse width
Recommended Use: Industrial YAG lasers Special Features: High power and energy density and large aperture
Spectral Range: Absorber: Aperture: Digital Power Scales: Maximum Average Power Density: Power Noise Level: Power Accuracy: Stabilization Time: Energy Scales: Energy Accuracy: Minimum Energy: Minimum Average Power: Maximum Pulse Width: Maximum Energy Density and Repetition Rate: 0.6 - 1.1m LP high damage threshold absorber 50mm 1500W/300W 6KW/cm2 0.7W 5% 8s 100J to1J 5% for energies > 30% of full scale 150mJ in repetitive mode, 500mJ in single shot 10W 200ms
L1500W-LP-RP
RP: Pulse width J/cm2 Max Repetition Rate <10s 0.1 15KHz 0.5ms 20 1.4KHz 5ms 120 150Hz 100ms 900 7Hz System / Display Specifications when used with Laserstar Display Function Specification Frequency Measurement Accuracy: 0.01% Statistics Displayed: Min, Max, Std Dev Data Memory Capacity (nonvolatile): 50,000 points Computer Interface: RS232 Standard, GPIB Optional Maximum Data Acquisition Rate: Sample to 15KHz, every pulse to 280Hz Max. Real Time Data Transfer to PC: 100Hz with GPIB
Ordering Information Item L1500W-LP-RP Description RP power/energy meter for industrial YAG and other long pulse lasers, for powers up to 1500W and energies to 100J. Ophir P/N 1Z02907
Maximum Laser Repetition Rate for a Given Pulse Width Setting for RP Heads
Maximum Pluse Width Setting (ms)
0.01 0.1 1 10 100 10000 100000
10000
1000
1000
10
67
BBH 10.6M
ABSORPTIVITY IN %
70.0 60.0
Pyro metalic
1.0 WAVELENGTH IN M
10.0
Thermal Heads
100
HE1,BB HE,SV P P LP HE1 HE BB BB Thermal
90 80 70 ABSORPTIVITY IN %
LP LP1
SV
LP1
60 50 40 30 20 10 0 0.1 1 WAVELENGTH IN M 10
68
Thermal Heads
100K
SV LP1 BB thermal <300W
1K
100
P P
10
2
0.1
LP LP1
0.01 10-10
10-9 1ns
10-8
10-7
10-6 1s
10-5
10-4
10-3 1ms
10-2
10-1
1 1s
Pyroelectric Heads
100K
10K
2
1K
100
10
2
Pyro BBH
1
0.5 0.3 0.2
0.1
0.01 10-10
10-9 1ns
10-8
10-7
10-6 1s
10-5
10-4
10-3 1ms
10-2
10-1
1 1s
69