Professional Documents
Culture Documents
1. CAPACITORS: Storage of Voltage and Filtering of Voltage. It indicate It is POLARITY Spare (+, -). =C
2. RESISTER: It Work CUT OFF Voltage and drug off Voltage. It indicate It is NON POLARITY Spare (+). =R
3. DIODE: It Work To converter A.C to D.C It indicate It is POLARITY Spare (+, -). =V
=L
=F
7. TRANSFORMER: Transformers are 2 types. 1. Step up transformer. 2. Step down transformer. 1. STEP UP TRANSFORMER: This type transformer is used for increase the Voltage.
Page 1 of 18
2. STEP DOWN TRANSFORMER: This type Transformer is used for to Convert A.C to D.C. It indicate
=V
=N
== X == I.C (Integrity Carquet) Working Conditions: 1. Anita Switch 2. PF, PA. 3. RX filter 4. TX filter 5. 13 Mega H Z Cristal. 6. Hazer 7. VCO 8. Power I.C. 9. Audio I.C. 10. R.T.C 11. C.P.U 12. Flash I.C 13. Charging I.C. 1. Anita Switch: - It Work to dived the RX Signals and TX Signals. If it is Failure or Un solaring No Net Work found 2. PA: - It Work to Transpecting the TX Signals. If it is Failure or Un solaring No Access 3. RX Filter: - To Filtering the unwanted Signals. If it is Failure or Un solaring No Net Work found 4. TX Filter: - To Filtering the unwanted Signals. If it is Failure or Un solaring No Access 5. 13 Mega H Z Cristal : - It Work receiving the 26 mega Hz frequenceing. Then Convert 13 Mega HZ. If it is Failure or Un solaring Seat dead, No Net Work 6. Hazer: - It Work Modulation and Demodulation. If it is Failure or Un solaring Seat dead, No Net work 7. V C O (Voltage Control Oscillator) : - It Work to Pass Voltage L.N.A (Low Noise Amplifier) Section. If it is Failure or Un solaring Seat dead, No Net work problems. 8. Power I.C: It Work to receiving the Primary Voltage and transecting the Secondary Voltage. { Primary Voltage Battery + & # Voltage, Secondary Voltage I.C out put + & # Voltage } If it is Failure or Un solaring Seat dead, No Net Work, Insert sim card, Buzzer problems 9. Audio I.C: - It Work to Convert Unlock to Digital Signals. If it is Failure or Un solaring No Speaker and No Mic.
Page 2 of 18
10. R.T.C: - It Work to Update regular time. If it is Failure or Un solaring to Display irregular Timing. 11. C.P.U (Central Processing Unit): - It Work to Control in the all the spears. If it is Failure or Un solaring Display problem, Key pad problem, etc 12. Flash I.C: - It Work booting the mobile phones. It store Flash data. If it is Failure or Un solaring Seat dead, No Net Work, Phone Hanging problems. 13. Charging I.C: - It Work to Controlling the Charging. If it is Failure or Un solaring Not Charging problems.
3310 Diagrams
Page 3 of 18
1100 Diagrams
VOLTEGES
Voltages are 2 types.
Page 4 of 18
1. Primary Voltage.
2. Secondary Voltage.
1. PRIMARY VOLTAGE: - Primary Voltage come to POWER I.C input (3.6 Volts)
2. SECONDARY VOLTAGE: - Secondary Voltage Come to POWER I.C output (1.5 V to 2.8 V) VANA V FLASH V CORE VIO VR VVCO - 2.8 V - 2.8 V - 1.8 V - 1.8 V - 2.8 V - 2.8 V
MULTI METTER
V DC 20 20 K
CHARGING PROBLEM
Page 5 of 18
General Checking 1. 2. 3. 4. Check the Charger ( it comes 6 Volts) If it is OK, then Check Charging Connector. If it is working then Check Charging Connector to Charging I.C or Power I.C input (6 Volts). If it is OK, then Check Charging output {(Power I.C to Battery Connector) (3.6 Volts)}.
NOTE:1. Check the Charging Connector. 2. Then Check F100, It comes Double Side 6Volts. 3. If it is OK, Then Check L100, It comes Double Side 6Volts. 4. If it is OK, Then Check C100, It Comes Single side 6Volts. 5. If it is OK, Then Check V1100, It Comes Double Side 6Volts. 6. If it is OK, Then Check OUT PUT of POWER IC, It Comes 3.6 Volts. 7. If it is OK, Then Check R200, It Comes Double Side 3.6Volts. 8. If it is OK, Then Check C201, It Comes Single Side 3.6Volts. 9. If it is OK, Then Check C202, It Comes Single Side 3.6Volts 10. If it is OK, Then Check C243, It Comes Single Side 3.6Volts 11. If it is OK, To Replace the BATTERY.
=== X ===
1. Check The Speaker Volume. 2. If it is OK, Then Check Speaker (with help of Multi Metter in BUZZER condition, It comes BUZZER Sound) 3. If it is OK, Then Check tips. 4. If it is OK, Then Check it tracks to Audio IC 5. If it is OK, Conform Audio IC if Failure.
____________________________________________________________________
NOTE: 1. 2. 3. 4. 5. 6. Check the Speaker Volume. If it is OK, Then Check the Speaker, with help of Multi Metter in BUZZER condition. If it is OK, Then Check Speaker Pad. If it is OK, Then Check Speaker Pad to Audio IC If it is OK, Then Check A track to L150 If it is OK, Then Check A track L150 to R161 (It Comes Double Side BUZZER Sound or with comes Single side Sound, another side Sounds 1.5 ). 7. If it is OK, Then Check B track L150 8. If it is OK, Then Check B track L150 to 10R (It Comes Double Side BUZZER Sound or with comes Single side Sound, another side Sounds 1.5 ) 9. If it is OK, Conform Audio IC is Failure. === O ===
1. Check The MIC and Replace 2. If it is OK, Then Check MIC tracks (Out put Audio IC) 3. If it is OK, Audio IC is failure.
--------------------------------------------------------------------------------------------------------
NOTE:1. Check the MIC, with help of Multi Metter 2. If it is OK, Then Check MIC tips. 3. If it is OK, Then Check MIC IC 4. If it is OK, Then Check A track to L102 5. If it is OK, Then Check A track L102 to C102. 6. If it is OK, Then Check A track C102 to R156. 7. If it is OK, Then Check A track L102 to R153 (GND) 8. If it is OK, Then Check A track R156 to C151 9. If it is OK, Then Check A track C151 to R151 10. If it is OK, Then Check A track R151 to R152 11. If it is OK, Then Check B track L102 12. If it is OK, Then Check B track L102 to C103 13. If it is OK, Then Check B track C103 to R157 14. If it is OK, Then Check B track R157 to C152 15. If it is OK, Then Check B track C152 to C152 16. If it is OK, Then Check B track C152 to R151 17. If it is OK, Then Check B track R151 to R155 18. If it is OK, Audio IC is Failure. === X ===
BUZZER PROBLEM
(To Hearing the RING TONE, LOUD SPEAKER and to Hearing the MP3 SONGS)
Page 8 of 18
GENERAL CHECKING:1. Check the Profile (Silent / Vibrating / Ringing). 2. If it is OK, Then Check BUZZER (with help of Multi Metter in BUZZER condition, It comes BUZZER Sound) 3. If it is OK, Then Check BUZZER tips. 4. If it is OK, Then Check BUZZER tracks. 5. If it is OK, Power IC is Failure.
------------------------------------------------------------------------
NOTE: 1. 2. 3. 4. 5. 6. 7. 8. 9. Check the Buzzer. If it is OK, Then Check A track to C192. If it is OK, Then Check A track C192 to L188 If it is OK, Then Check A track L183 to C188 If it is OK, Then Check B track C191 If it is OK, Then Check B track C191 to L182 If it is OK, Then Check B track L182 to C187 If it is OK, Then Check B track C187 to Battery + tip. If it is OK, Power IC is Failure. ==== O ====
2. NO ACCESS - (TX) 1) NO NET WORK FOUND:MENU SETTING PHONE SETTING NET WORK SELECTION MANUAL SELECTION. GENERAL CHECKING: 1. 2. 3. 4. 5. Check the ANTINA Then Check ANTINA SWITCH (then Replace) If it is OK, Then Check RX Filter (then Replace). If it is OK, Then Check 13 MHz Cristal (Replace). If it is OK, HUZZER IC is Failure.
NOKIA 3310,3330,3410,3315
NOKIA 7250
ALCATEL 311
SAMSUNG N500
Page 10 of 18
SAMSUNG N620
2) NO ACCESS : MENU SETTING PHONE SETTING NET WORK SELECTION MANUAL SELECTION. Then Show Net work option. Then Select perfect net work. It show NO ACCESS problem. GENERAL CHECKING: 1. 2. 3. 4. 5. Check the ANTINA. If it is OK, Then Check the PF. Then Check PF to Battery tips. If it is OK, Then Check TX filter. If it is OK, HUZZER IC is Failure. === X ===
GENERAL CHECKING:1. 2. 3. 4. Check the SIM. If it is OK, Then Check SIM tray. If it is OK, Then Check SIM tracks. If it is OK, Then Replace SIM IC.
----------------------------------------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------------------------------------
GENERAL CHECKING:1. 2. 3. 4. Check the Keypad lock. If it is OK, Then Check Keypad Cristal. If it is OK, Then Check Keypad Row and Column track. If it is OK, Then Replace Keypad IC.
=== X ===
1. 2. 3. 4. 5.
Check the Battery (3.6 Volts). If it is OK, Then Check Soft Ware (FLASHING). If it is OK, Then Check DRAY SOLARING with help of BLOWER) If it is OK, Then Check PRIMARY VOLTAGE (Battery Connector to Power IC input 3.6 Volts). If it is OK, Then Check SECONDARY VOLTAGE [Power IC output (1.5 V to 2.8 V)]. I. VANA 2.8 V (C.P.U) II. V.FLASH 2.8 V (FLASH IC) III. V.CORE 1.8 V (HUZZER) IV. V I O 1.8 V (FLASH IC) V. V R 2.8 V (V C O) VI. V V C O 2.8 V (AUDIO IC) 6. If it is OK, Then Replace the 13 MHz Cristal IC. === O ===
-------------------------------------------------------------------
=== X===
GENERAL CHECKING:1. 2. 3. 4. Check the Battery Connector. If it is OK, Then Check PF (Replace). If it is OK, Then Check Bluetooth IC (Replace). If it is OK, Then Check Power IC.
BLUETOOTH PROBLEM
GENERAL CHECKING:1. Check the Bluetooth Voltage track. 2. If it is OK, Then Check Bluetooth IC. === O ===
=== O ===
GENERAL CHECKING:1. 2. 3. 4. 5. Check the Display Contrast. If it is OK. Then Check Display Contract. If it is OK, Then Replace Display Strip. If it is OK, Then Display tracks. If it is OK, Then Replace Display IC.
----------------------------------------------------------------------------
=== O ===
GENERAL CHECKING:1. 2. 3. 4. 5. Check the Display Settings. If it is OK, Then Check Display (Replace). If it is OK, Then Check it tracks. If it is OK, Then Replace COIL. If it is OK, Then Replace LED IC.
=== X ===
VIBRETING PROBLEM
GENERAL CHECKING:Page 17 of 18
1. 2. 3. 4.
Check the Profile. If it is OK, Then Check VIBRATOR, with help of DC Power Supply (1.5 Volts). If it is OK, Then Check it tips. If it is OK, Then Check OUTPUT OF POWER IC and V.BAT.
--------------------------------------------------------------------
NOTE: REMOVE ICS:- SIM IC, KEY PAD IC, BLUETOOTH IC, MMC (Micro Memory Card) IC, DISPLAY IC, LED IC Winnsoft solutions Anand Sir Ph: 9346394613
Page 18 of 18