Professional Documents
Culture Documents
greater than of lessthan than Vref.The comparator is sometimes also called a voltage level detector because, for a desired value of Vref the voltage level of voltage Vin can be detected. Procedure: Adder: 1) Connections are made as per the circuit diagram. 2) V1, V2, V3 terminals are given to Ttl logic 0 to +5V 3) Output is observed on CRO at pin no. 6 4) Output values are noted down for different input combinations(000, 001, 010, 011, 111) 5) Compare theoretical and practical values. Subtractor: 1) Connections are made as per the circuit diagram. 2) V1, V2 terminals are given to Ttl logic 0 to +5V 3) Output is observed on CRO at pin no. 6 4) Output values are noted down for different input combinations(00, 01, 10, 11) 5) Compare theoretical and practical values. Comparator: 1) Connections are made as per the circuit diagram. 2) Vref is given as +5V 3) Vin is given as +20Vp-p. 4) Output is observed on CRO at pin no. 6 5) Channel 1 is connected to output and channel 2 is connected to sine wave input.
6) Note down the + Vsat value from the output.
Result: For adder and subtractor theoretical and practical values are compared and found to be equal (appro.,). For Comparator +Vsat= 22V
Input 000 001 010 011 100 101 110 111 Input 00 01 10 11
Output Theoritical
Output Practical
Output theoretical
Output practical
2. INTEGRATOR AND DIFFERNTIATOR USING IC 741 OP-AMP Aim: To Design an Integrator and Differentiator using IC-741 Op amp and also Study the frequency response of both integrator and differentiator. Apparatus:
1) IC 741 Op-amp (1).
2) Resistors: 82(1), 1K(1), 5K(1), 10K (1) 3) Capacitors: 0.005F(1), 0.01F(1), 0.1F(1) 4) Signal Generator 5) CRO
6) Connecting wires & Probes
7) Trainer kit Theory: Integrator is normally operated in the inverting mode. If Vin is the input voltage applied at the inverting terminal of the Op-amp, Vo is the output, which is delivered by the relationship Vo=-(1/R1Cf) Vin dt The output voltage is directly proportional to the negative integral of the input voltage and inversely proportional to the time constant R1Cf .The integrator converts the sinusoidal to cosine or a triangular to a square wave. For perfect integration the time period T of the signal is larger than or equal to R1Cf. i.e. T> R1Cf where R1Cf = 1/2fa
Where fa is gain timing frequency. Integrator is in analog computers and Analog to digital converters and signal wave shaping circuits. Differentiator: It is normally operated in the inverting mode. If Vin is the input voltage applied at the inverting terminal of the Op-amp,vo is the output, which is derived by the relationship Vo=-R1Cfd/dt(Vin) The output voltage is directly proportional to the negative derivative of the input voltage and inversely proportional to the time constant R1Cf. the Differentiator converts square to a spikes.For perfect integration the time period T of the signal is larger than or equal to RFCF i.e. T> RFCF, where RFCF = 1/2fa Where, fa is gain timing frequency. Differentiator is used in wave shaping circuits, and FM modulators. Design of Integrator: Gain limiting frequency fa= 1/2RfCf Let fa=1 KHz, RF= 10K CF=1/2faRF F Design of differentiator: fa=1/2RFC1, fb=1/2RFc1 Let fa=1KHz,C1=0.1F fb=20fa, R1=1/2fbC1 Procedure 1) Connections are made as per the circuit diagram.
2) The input is applied from a signal generator to the inverting terminal and the
Result: Thus the integrator and differentiator were designed and their frequency resposes were studied.
3. Active Low Pass and & High Pass Butterworth (Second Order) Filter
Aim: To obtain the frequency responses of the second order LPF and second order HPF. Apparatus: 1) IC-741 Op-amp(1) 2) Resistors 10K(3), 33K(2), 27K(1) 3) Potentiometer-22k(1) 4) Capacitors-0.01F(1),0.0047F(2) 5) CRO 6) Probes & connecting wires 7) Trainer kit Theory: The second order LPF uses an RC network for filtering and an Op-amp is in NI configuration hence it does not load down the RC network. The gain magnitude and phase angle equation of the LPF can be obtained by Vo/Vin=Af/(1+(f/fh)2 )
= -tan-1(f/fh)
fh =1/2RC Af =1+(Rf/R1) Second order HPF can be formed by simply inter changing the frequency determining resistors and capacitors in LPF. A 2nd order HPF is formed from a 2nd order LPF by inter changing components R &C. It has a lower cutoff frequency fh at which the magnitude of the gain 0.5 times the pass band value the highest frequency in passband is determined by closed loop bandwidth of the Op-amp. Vo/Vin=Af (f/f1)/(1+(f/f1)2 ) Where f1=1/2RC Designs of II order LPF: Let fh=1 KHz, R1= 1K,C=0.01F fh =1/2RCR=15.9K Af =1+ (Rf/R1)=2 Rf=R1=10K Design of II order HPF: Let f1=1KHz, C=0.01F R=(1/2f1C) =15.9K Af=1+(Rf/R1)=2Rf=R1=10K
Procedure:
1) Connections are made as shown in the circuit diagrams fo both LPF and HPF.
2) Switch on the power supply. 3) Connect the output pin (pin 6) to CRO. 4) By varying the frequencies of the input signals observe and note down the output values. 5) Plot the frequency response of LPF and HPF on graph sheet with gain in db on Y-axis and frequency in Hz on X-axis.
Precautions:
1) Avoid loose connections 2) Avoid unnecessary short connections Result: The frequency responses for 2nd order LPF & HPF are observed and plotted on the graph sheet.
Frequency Response: LPF: Vin constant Vin Frequency (in Hz) Vo(in V) Gain=20log(Vo/Vin) (in db)
3) Capacitors: 0.1F(3) 4) CRO 5) Connecting Wires & Probes 6) Trainer Kit Theory: This is the one type of audio frequency RC oscillator. The Op-amp provides a phase shift of 1800 as it is used in inverting mode. An additional phase shift of 1800 as it is provided by the
feedback RC network. The gain Av should be greater than 29 to ensure that variations in circuit parameters will not make (Av)<1, otherwise oscillations will die out . Design: fo=1/2 RC and Rf=29R
Let C=0.1F fo =500Hz R=1.3K To prevent loading R1=10R Therefore take R1=10R=15K Rf =29*15K=435K Procedure: 1) Connections are made as per the circuit diagram 2) See the output waveform on the oscilloscope and adjust rf to obtain a sine wave output.
3) Measure the frequency of oscillation, voltage amplitude and plot the waveforms.
Precautions: 1) Avoid loose connections 2) Avoid unnecessary short connections Result: The RC phase shift oscillator is constructed by using IC -741 Op-amp and the frequency of oscillations fo is obtained.
2) Resistors: 3.3K(2), 12K(1) 3) Potentiometer: 50K(1) 4) Capacitors:0.05F(2) 5) Probes & Connecting Wires 6) CRO 7) Trainer Kit Theory: This is one of the audio frequency oscillator, in which the feedback signal is given to the positive input terminal of the Op-amp. So it is called as a non inverting amplifier. Therefore the feedback network needs not to provide any phase shift. The condition of zero phase shift is achieved by balancing the bridge. As =1/3 at fo. Therefore for sustained oscillation, the amplifier must have a gain of precisely 3. Design: fo= 1/2RC and Rf=2R1 Let C=0.05F, fo=1KHz R=1/2foC Procedure: 1) Connections are made as per the circuit diagram 2) Observe the output wave form on the CRO 3) Note down the amplitude and frequency of the waveform.
4) Compare the practical and theoretical values.
Precautions: 1) Avoid loose connections 2) Avoid unnecessary short connections Result: Wein bridge oscillator is constructed by using IC-741 Op-amp and frequency of oscillations fo is obtained.
Procedure: 1) Connect the circuit as per the circuit shown in the diagram
2) Apply the square wave input to the input of trigger circuit and apply the output of trigger circuit at the pin 2 of the 555 timer 3) Note downthe pulse width of the monostable multivibrator. 4) Compare the theoretical and practical values
Precautions: 1) Avoid loose connections 2) Avoid unnecessary short connections Result: The working of the 555 timer in the monosatble mode is studied.
upper threshold voltage VUT and lower threshold Voltage VLT. These threshold voltages are obtained by using voltage divider R1-R2, where the voltage across R1 is fed back to the +ve input. The voltage across R1 is variable reference threshold voltage that depends on the value and polarity of the output voltage Vo. When Vo=+Vsat, The voltage\e across R1 is called the upper threshold voltage VUT. The input voltage Vin must be slightly more positive than VUT in order to cause the output Vo to switch from +Vsat to Vsat. As long as Vin <Vsat, Vo is at + Vsat. VUT=(R1/(R1+R2))(+Vsat). On the other hand, when Vo is at Vsat, the voltage across R1 is referred as lower threshold voltage, VLT.Vin must be slightly more negative than VLT inorder to cause Vo to switch from Vsat to +Vsat, i.e. for Vin values greater than VLT is at Vsat VLT=(R1/(R1+R2))(-Vsat). Thus if the threshold voltages VLT and VUT are made larger than the input noise voltages, the +Ve feedback will eliminate the false output transitions. Also the +Ve feedback, because of its regenerative action, will make Vo switch faster between +Vsat and Vsat. The output of the Schmitt trigger is a square wave when the input is a sine wave. Procedure: 1) Connect the circuit as per the circuit diagram. 2) Input of 1 Vp-p sinewave is given from function generator. 3) Output is observed on CRO
4) VUT and VLT are calculated and noted down by observing the output on CRO. 5) The hysteresis voltage is found as Vhy=VUT-VLT.