Professional Documents
Culture Documents
25 February 2010 Revisions required to Concise Eurocode 2 (Oct 06 edition) due to revisions in standards, notably Amendment 1 to NA to BS EN 1992-1-1:2004 dated Dec 2009, and interpretations.
Page 11 12 13 13
Why/old text Revisions to BS 8500-1 Revisions to BS 8500-1 Revisions to BS 8500-1 New reference
Revised text See A below See B below See C below BS 8500-1 A.2.4
14
4.5
30
5.6.2.1
NA Amd 1 The minimum cover for concrete cast on prepared ground (including blinding) is 40 mm and that for concrete cast directly against soil is 65 mm. Interpretation For columns in braced systems ei = l0/400 (i.e. i = l/200 for most braced columns). The design eccentricity should be at least (h/30) but not less than 20 mm.
The nominal cover for concrete cast on prepared ground (including blinding) should be at least 40 mm and that for concrete cast directly against soil should be at least 75 mm. For columns in braced systems ei = l0/400 (i.e. i = l/200 for most braced columns). The design eccentricity should be at least e0 = (h/30) but not less than 20 mm. 5.2.7 6.1(4)
30
5.6.2.1 5.2.7
31 43
Figure 5.10 Edit M0e + M2 7.3.2 NA Amd 1 1 VRd,max = bw z fcd /(cot + tan ) VEd with vertical links = bw z fcd(cot + cot )/(1 + cot2 ) VEd with inclined links 7.3.2 NA Amd 1 Additional text normally be used = 0.6 [1 (fck/250)] = . . . NA Amd 1 Additional text = angle of inclination of the strut, such that cot lies between 1.0 and 2.5. The value of cot should be obtained by substituting VEd for VRd,max
See D below
VRd,max = bw z 1 fcd /(cot + tan ) VEd with vertical links = bw z 1fcd(cot + cot )/(1 + cot2 ) VEd with inclined links
43
43
7.3.2
= angle of inclination of the strut, such that cot lies between 1.0 and 2.5. The value of cot should be obtained by substituting VEd for VRd,max. For sections under axial tension (not restraint) cot should be limited to 1.25
Page 1 of 5
43
7.3.2
NA Amd 1 Additional text For vertical links cot = 0. NA Amd 1 Additional text . . . . given in Table 7.2.
53
8.6
At the . . . . given in Table 7.2. In addition at the first control perimeter vEd should be limited to 2vRd,c
56
9.2
Edit Torsional resistance governed by the Torsional resistance governed by the area of closed links is given by: area of closed links is given by: TRd = Asw/s) = TEd/(2Ak cot ) fywd TRd = 2Ak(fywdAsw/s)cot Therefore Asw/s = TEd/(2Ak cot fywd)
72
74
77
80
80
82
93
94
100
Interpretation Revise text The intention is to provide an even distribution/density of punching shear reinforcement within the zone where it is required. One simplification to enable rectangular perimeters of shear reinforcement is to use an intensity of Asw/u1 around rectangular perimeters. 12.5.2 NA Amd 1 Para 3 Additional text The spacing of transverse reinforcement should be the least of 13.2 Corrigendun No 1 Revised text Ftie,per = (20 + 4n0) kN 60 kN where n0 = number of storeys 14.1 NA Amd 1 Revised text Generally the design tensile strength fctd,pl = 0.6 fctk,0.05/c (as shown in Table 14.1). Table 14.1 NA Amd 1 Revised data. New values of fctd c, lim Table 14.2 NA Amd 1 Revised data. New values of fcvd F3 NA Amd 1 Revision to interpretation of s Delete text. See G below 15.8 NA Amd 1 Revision to interpretation of s for l/d The appropriate SLS stress in reinforcement, s, may be determined as outlined for F3 in Section 15.7. References NA Amd 1 1a National Annex to Eurocode 2Part 1-1. BSI 2005
12.4.3
For concrete class C50/60, the spacing of transverse reinforcement should be the least of
Generally the design tensile strength fctd,pl = 0.8 fctk,0.05/c (as shown in Table 14.1).
See E Below
See F Below
See G below The appropriate SLS stress in reinforcement, s, may be determined as outlined below + text from F3. See H below 1a National Annex to Eurocode 2- Part 1-1. Incorporating Amendment No.1 BSI 2009
Page 2 of 5
103
Table A1
C32/40 C30/37
RC50
RC40
RC35
RC30
C38/35 C28/35
IVB IVB-V
x3
C35/45 C32/40
C32/40 C28/45
0.55 320
C35/45 C32/40
IVB IVB-V x3
Page 3 of 5
RC50
RC45
RC40
RC35
IVB IVB-V
Note For corrosion induced by chlorides see BS8500-1 Table A.5
M0e + M2 M0e
Page 4 of 5
25 0.96 1.37 1.68 1.95 2.17 2.27 2.26 2.14 1.89 1.43
35 1.20 1.62 1.96 2.24 2.50 2.73 2.92 3.04 3.07 3.02 2.88
40 1.31 1.74 2.08 2.38 2.64 2.88 3.09 3.29 3.41 3.45 3.42
45 1.42 1.85 2.20 2.50 2.77 3.02 3.24 3.45 3.64 3.77 3.82
50 1.52 1.96 2.31 2.62 2.90 3.15 3.38 3.60 3.80 3.99 4.12
G Amends to p 93
New text:
as either 310/s using characteristic load combinations to determine the service stress, s
or (500/fyk)(As,prov /As,req)
H Amends to p94