You are on page 1of 11

BGS238 PROFESSIONAL SKILLS FOR APPLIED GEOCSIENTISTS

SCHOOL OF EARTH & ENVIRONMENTAL SCIENCES Engineering Geology of Dams

Engineering Geology of Dams

Brain-storm the various geological and engineering aspects of dam construction.

Engineering Geology of Dams



What is the purpose of a dam? Do you need to extend your list above to include aspects to do with the reservoir area?

Engineering Geology of Dams

What will influence the positioning of the dam?

Engineering Geology of Dams

How can we work out how big (how high) the dam needs to be?

Engineering Geology of Dams


Nature of Valley Chord Height Ratio

Gorges

Less than 3

Narrow Valleys

Between 3 - 6

Wide Valleys

Greater than 6

Flat Country Plains

Embankments used to create reservoir volume. Eg. Near Heathrow

Modified from Walter, R. C. S (1962) Dam Geology.

Engineering Geology of Dams

Types of Dam
Arch or Buttress Dam

Gravity Dam

Embankment Dam

Engineering Geology of Dams


Types of dam Principal design factors

Gravity

Stability derived from self-weight. Ground anchors can be used to increase stability. Masonry or concrete. Used in narrow to wide valleys with Chord / height ratio 5 to 8 eg Vyrnwy (Wales) =7 and the Three Gorges dam in China

Buttress

Reinforced concrete buttresses used to transfer thrust to foundation. Used in very wide valleys eg Errochy =10 and Shira =15 (Scotland)

Arch dam

Stability derived from the curved shape of the dam transferring the forces to the abutments. Reinforced concrete, can be thick (chord/height ratio of 3 5) or thin skinned (c/h< 3, radius <150m), single or double curvature. Can withstand large deflections in the foundations IF the deflections are uniformly distributed. Common in mountainous areas with gorges or narrow valleys eg Vaiont dam, Italy

Earthfill and Rockfill Embankments

Used in wide valleys where foundation materials are deformable and/or variable. Has a very wide footprint with shallow slopes. Constructed from local materials derived from within the reservoir area. The impermeable core can be clay or asphalt concrete. Very common in UK, but also the High Aswan dam (dune sand) in Egypt

Engineering Geology of Dams

Concrete Dams

Typical cross-section for concrete dams: (a) Gravity (b) Buttress (c) Arch Drainage measures for an arch dam. Drainage curtain: downstream (D) of grout (G) cut-off and upstream of stressed zone. The closure of fractures in the stresses zone in-situ reduces permeability and allows development of excessive groundwater pressure.

Engineering Geology of Dams

Arch Dam

Forces on a Arch Dam

Arch Dam: Forces The arch squeezes together as the water pushes against it. The weight of the dam also pushes the structure down into the ground.

Engineering Geology of Dams

Buttress Dam

Forces on a Buttress Dam

Buttress Dam: Forces Water pushes against the buttress dam, but the buttresses push back and prevent the dam from toppling over. The weight of the buttress dam also pushes down into the ground.

Engineering Geology of Dams

Embankment Dam

Forces on an Embankment Dam

Embankment Dam: Forces Water pushes against the embankment dam, but the heavy weight of the dam pushes down into the ground and prevents the structure from falling over.

Engineering Geology of Dams

Gravity Dams

Forces on a Gravity Dam

Gravity Dam: Forces Water pushes against the gravity dam, but the heavy weight of the dam pushes down into the ground and prevents the structure from falling over.

Engineering Geology of Dams

Principal Parts

Engineering Geology of Dams

Dam Location Issues

Catchment Reservoir Slope


Stability

Foundation
Rock

Silting

Engineering Geology of Dams

What Geological Input is required for the engineering of a large dam?

The stability and safety of the dam on its foundations; The water-tightness of the reservoir basin; The slope stability of the reservoir perimeter The availability of suitable local materials for its construction.

Engineering Geology of Dams

Finally, bearing in mind how the dam might behave, think through appropriate tests and hence decide on what sampling would be required.

Engineering Geology of Dams



Additional notes: Stability is obviously the major factor. This involves The Dam

The dam must function safely The water pressure acting on the face of the dam may cause
sliding and / or trigger earthquakes

The water pressure acting in any discontinuities, cracks or voids


in the foundations may cause uplift. Treatment may involve grout and / or drainage curtains

Engineering Geology of Dams



Additional notes: Stability is obviously the major factor. This involves Upstream : The Reservoir Rim

Will flooding impounding water trigger landslides Could a landslide cause a flood wave over the dam Will waves on the water surface cause erosion
Downstream.

Will spillway water cause erosion What would happen downstream in the event of failure or flood

Engineering Geology of Dams



Additional notes: Stability is obviously the major factor. This involves Other factors are topography and hydrology (which partly determines the capacity of the reservoir and height of the dam), erosion of the catchment and the rate of siltation, measures to allow safe overtopping during flood (spillway design), riparian water and earthquake accelerations. The aim is to build the most cost effective structure, commensurate with safety, which gives, for the particular river discharge, the largest reservoir capacity created by the cheapest dam.

10

Engineering Geology of Dams

Other Points to note:


For undergraduate projects, it is best to focus on either an embankment dam (soil or rock filled) or a concrete gravity dam, as it is possible to do a reasonable analysis in terms of stability. Concrete gravity dam :- sliding failure and toppling failure (see MD lectures at level3) Embankment dams (rock and soil fill):- Sliding failure, failure of upstream and downstream slopes (NK lectures at level 3). Also consider the source of the fill material, its suitability, excavation methods and the temporary stability of the borrow pits, (which should be in the reservoir area so that they are flooded to reduce visual and environment impact). With rock fill, there is also the question of forming an impermeable membrane or core of either clay (if there is some available locally) or asphalt.

Engineering Geology of Dams

Key references

EM 1110-2-2200 EM 1110-2-2201

088 238

CECW-ED CECW-ED

Gravity Dam Design Arch Dam Design

30 Jun 95 31 May 94

EM 1110-1-2908

065

CECW-EG

Rock Foundations

30 Nov 94

EM 1110-2-1420

148

CECW-EH-Y

Hydrologic Engineering Requirements for Reservoirs

31 Oct 97

11

You might also like