Professional Documents
Culture Documents
This document originally produced and documented by EvoScan. Special thanks to those others whom contributed to this document. http://www.limitless.co.nz/Evoscan You can visit the website for the latest version of this document. Please do not distribute this document without the EvoScan website address and EvoScan logo attached, thanks.
USDM Rom / wiring only Possible fault codes Yellow Tabs IC sprayer system Optional Red Tabs wiring changes for ECU swap Evo 8 RalliArt JDM/USDM
Pin
Evo 5 / Evo 6
Evo 4
1 No. 1 Injector each injector is 2 - 3 plus resistor pack is 5.8 - 6.2 2 No. 3 Injector 3 Fuel Pressure Solenoid 4 Idle Speed Control (ISC) Motor Coil (A1) 5 ISC Motor Coil (B1) 6 EGR Solenoid 7 8 A/C compressor relay 9 Evaporate Emission Purge Solenoid 10 Ignition Power Transistor (for cyl 1&4) 11 Turbo Wastegate Solenoid 12 12V Switched Power Supply 13 Chassis Ground 14 No. 2 Injector 15 No. 4 Injector 16 17 ISC Motor Coil (A2) 18 ISC Motor Coil (B2) 19 Volume Air Flow Sensor Reset Signal 20 21 Radiator Fan Motor Relay (PWM Output) 22 Fuel Pump Relay 2 23 Ignition Power Transistor (for cyl 2&3) 24 A/C load signal 25 12V Switched Power Supply 26 Chassis Ground Pin 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 Pin 51 52 53 54 55 56 57 58 59 60 61 62 Pin 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92
No.1 injector each injector is 2 - 3 plus resistor pack is 5.8 - 6.2 No.3 injector Fuel pressure control valve Idle Speed Control (ISC) Motor Coil (A1) ISC Motor Coil (B1) Secondary air control solenoid valve Fuel pump relay 1 Ignition Power Transistor (for cyl 1&4) Turbo Wastegate Solenoid 12V Switched Power Supply Chassis Ground No.2 injector No.4 injector ISC Motor Coil (A2) ISC Motor Coil (B2) Volume Air Flow Sensor Reset Signal Radiator fan motor relay (Hi) Coolant temp. above 105C Radiator fan motor relay (Lo) Coolant temp. 90-100C A/C compressor relay Ignition Power Transistor (for cyl 2&3) 12V Switched Power Supply Chassis Ground
No.1 injector each injector is 2 - 3 plus resistor pack is 5.8 - 6.2 No.3 injector Fuel pressure control valve Idle Speed Control (ISC) Motor Coil (A1) ISC Motor Coil (B1) Secondary air control solenoid valve Fuel pump relay 1 Ignition Power Transistor (for cyl 1&4) Turbo Wastegate Solenoid 12V Switched Power Supply Chassis Ground No.2 injector No.4 injector ISC Motor Coil (A2) ISC Motor Coil (B2) Volume Air Flow Sensor Reset Signal Radiator fan motor relay (Hi) Coolant temp. above 105C Radiator fan motor relay (Lo) Coolant temp. 90-100C A/C compressor relay Ignition Power Transistor (for cyl 2&3) 12V Switched Power Supply Chassis Ground
Connector 60/C119
Condensor Fan Relay (Hi) Coolant temp. above 105C Generator G Terminal Condensor Fan Relay (Lo) Coolant temp. 90-100C Intercooler Sprayer activation light Check Engine Light (Service Engine Soon) Power Steering Pressure Switch (Input) Engine control relay Fuel Pump Relay 3 (Additional pressure for higher loads) Sensor Ground (IAT, Cam and Crank Angle Sensors) Alternator FR terminal Clutch Position Switch (Input) Intercooler Sprayer switch (Auto) A/C pressure switch Fuel Tank Level (Input) USDM Connector 61/C117 Imobilizer ECU (Anti-Theft) Secondary Air System solenoid O2 Sensor Heater (rear) EVAP Vent Solenoid Valve USDM / IC spray relay JDM Diagnostic OBDII Pin 1 IC spray relay USDM Tachometer signal O2 Sensor Heater (front) Fuel Tank Differential Pressure Sensor USDM Diagnostic OBDII Pin 7 - ISO K Line Condensor Fan Relay (Hi) Coolant temp. above 105C Generator G Terminal Condensor Fan Relay (Lo) Coolant temp. 90-100C Intercooler Sprayer activation light Check Engine Light (Service Engine Soon) Power Steering Oil Pressure Switch Engine control relay Fuel Pump Relay 3 Alternator FR terminal Alternator G terminal Alternator G terminal
Check Engine Light (Service Engine Soon) Power Steering Pressure Switch (Input) Engine control relay Fuel pump relay No.2 (Additional pressure for higher loads) Sensor Ground (IAT, Cam and Crank Angle Sensors) Alternator FR terminal
Check Engine Light (Service Engine Soon) Power Steering Pressure Switch (Input) Engine control relay Fuel pump relay No.2 (Additional pressure for higher loads) Exhaust temperature warning lamp Alternator FR terminal
Imobilizer ECU (Anti-Theft) Secondary Air Control Solenoid Valve O2 Sensor Heater (rear) IC spray relay JDM Diagnostic OBDII Pin 1 Tachometer signal O2 Sensor Heater (front) Diagnostic OBDII Pin 7 - ISO K Line
Diagnostic OBDII Pin 1 Tachometer signal O2 Sensor Heater (front) Diagnostic OBDII Pin 7 - K Line
Recap For Evo4/5/6 to Evo7/8 Ecu wiring conversion: Connect cable 8 to pin 22 (Fuel pump relay swaps with AC control relay) *not req. for Evo7 ecus I checked Connect cable 22 to pin 8 (AC control relay swaps with Fuel pump relay) *not req. for Evo7 ecus I checked Disconnect pin 87 AYC/ACD signal Connect Cable 20 to pin 32 (Rad. fan hi to Condensor fan hi) Connect Cable 21 to pin 34 (Rad. fan lo to Condensor fan lo) Connect cable 6 Secondary air system to pin 53 Disconnect pin 91 or rewire for IC sprayer manual operation Evo 4 only: Disconnect pin 40 and ground cable or connect to pin 92 sensor ground *definitely required Evo 4 only: Disconnect pin 33 if alternator is not charging battery *not required for any Evo4's I tried