Professional Documents
Culture Documents
Gen'l. Availability Corrosion Resistance Cut to Length Sheet Typical Characteristics* Weldability Arc Resistance, spot and steam Cold Workability Machinability Specified Mechanical Properties Where range is shown, property varies with specific width and/or thickness dimensions Tensile Strength - Ksi Ultimate
11 16 14 20 25 31 34 63-64 56-64 58-62 58-63 56-63 55-61 30 42 40-42 30 76-77 67-77 68-75 15.5 21 19 26 31 38 41 32 30-32 22 40 36-39 3.51 141 51 171 9.51 231 261 42 40-41 38 39-40 40-41 34-38 12 16 35 35 14 65-66 53-66 58-64 Elongation in 2" or 4 times diameter -percent minimum
Sheet Plate
Alloy
Brazability
Plate
Yield
14 14 12 21 20-21 -
Gas
1100
3003
5052
Alclad 2024
6061
O H14 F O H14 F O H32 H34 O3 T3 T351 T422 O3 T3 T351 T422 O31 T4 T6 T651 T422 O1 T6 T651 O1 T6
x X X X X X X X X X X X X X X X X X
x X X X X X X X X X -
x X X X X X X -
X X X X X X X X X X -
A A A A A A A C C C C A A A A A A A A A C C C A A
A A A B A B B B C C C B D D D A C C C C D D D B D
D C D C D C C D B B B D B B B D C C C C D B B C B
A A A A C C C D D D D D D D D A A A A A D D D D D
A A A A A A A D D D D D D D D A A A A A D D D D D
A A A A A A A C C C C C C C C A A A A A D D D D D
B A B A B A A B A A A B A A A B A A A A B B B B B
15-30 3-9 14-25 1-7 15-20 4-9 3-7 12 10-15 12-15 10-12 10-15 10-15 10-18 10-16 4-10 10-16 10 7-8 9-10 5-8
Ratings A, B, C, D are relative in decreasing order of merit. weldability and brazability ratings are specifically defined as: A - Generally weldable by all commercial procedures and methods. B - Weldable with special technique or specific applications which justify preliminary trials or testing to develop welding procedure and weld performance. C - Limited weldability because of crack sensitivity or loss on resistance to corrosion, and all mechanical properties. D - No commonly used welding methods have so far been developed.
1 - These yield strengths not determined unless specifically requested. 2 - Although sheet and plate are not sold in this temper, material heat treated from any temper by the user should attain the mechanical properties applicable to this temper. 3 - Annealed (0 temper) material shall, upon heat treatment, be capable of developing the mechanical properties applicable to T 42 temper material. 4 - Annealed (0 temper) material shall, upon heat treatment and aging, be capable of developing the mechanical properties applicable to T 67 temper material.
1100
Alclad 2014
2024
3003
5052
6061 7075
1. Minimum permissible radius over which sheet or plate may be bent varies with nature of forming operation. type of forming equipment, and design and conditions of tools. Minimum working radius for a given material or hardest alloy and temper for a given radius can be ascertained only by actual trial under contemplated conditions of fabrication. Where range is shown, use a smaller radius with extreme caution.
2. Alclad sheet can be bent over slightly smaller radii than the corresponding tempers of the uncoated alloy. 3. Immediately after quenching, this alloy can be formed over appreciable smaller radii. 4217661360076962